Robinhood OBAC606D57SS Installation and Operation Guide

Description: Robinhood Alto 5, 6 & 10 Function Stainless Steel 60cm Ovens

Model Numbers: OBAC605M57SS, OBAC606D57SS, OBAC610D57SS

OBAC605M57SS

Issue 9

OBAC606D57SS

OBAC610D57SS

Warning and safety information

This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.

Do not leave this oven unattended or unsupervised whilst children or infirmed are present.

During use the appliance will become hot, care should be taken to avoid touching heating elements inside the
oven.

Accessible parts may become hot during use, to avoid burns young children should be kept away.

The installation of this oven is to be carried out by using only a qualified electrician and must be earthed.

This oven is to be installed in accordance with the local, national building, electrical and plumbing codes.

If the power supply cable is damaged, it must be replaced by the manufacturer or its service agent or similarly
qualified person to avoid a hazard

The oven is not intended to be operated by means of an external timer or separate remote-control system.

Do not allow electrical fittings or cables to be in contact with hot areas of the appliance.

Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven glass doors since they can
scratch the surface, which may result in shattering of the glass

Do not clean the oven with an steam cleaner

.

Installing the built in oven

Important: the power supply to the appliance must be turned off before any adjustments or maintenance work.

Installation of Built-in Oven

To ensure the proper working order of the built-in appliance, the kitchen unit must be of a suitable size.
To provide adequate ventilation, there must be appropriate ventilation openings in the front bottom and the top part of

200 cm2, and an exhaust opening on the bottom of a least 200 cm2 , and an exhaust opening of at least 60 cm2 .
The unit panels next to the cooker must be heat resistant. In the case of veneered wood units, glues must be resistant
to a temperature of 100℃.

In accordance with safety standards, once the appliance has been mounted, there must be no possible contact with
electrical parts. Any protective parts must be secured so that they can only be removed with the use of tools.

2

Installing the built in oven

Positioning the appliance
Ensure that the aperture that you will be fitting

the oven into, is of the size given in the
diagram.

The oven must be fitted into an oven housing
with the ventilation cut-outs shown in the
“Ventilation requirements” section below

Ensure that the rear panel of the furniture
housing unit has been removed.

Cooling fan
A tangential cooling fan is fitted inside of this
appliance, to make the internal temperature
of the oven stable and the external surface
temperature lower. After the oven has been
used the cooling fan will run on for a period
of time, until the oven is sufficiently cooled.

Ventilation requirements

(Figure shows the ventilation and cut-out requirements
for the installation of the appliance into a standard
kitchen unit).

(Figure shows the ventilation and cut-out requirements
for the installation of the appliance into a tall housing unit).

Fastening the oven

Insert the appliance into the
compartment; open the oven
door and fasten the oven to
the cabinet using the four
screws “A”, remembering to
place the special spacers
provided between the hole
and the screw itself.

3

Installation- continued

Electric connection

Cookers with a three-pole power supply cable are designed to operate with alternated current at the supply frequency and
voltage indicated on the data plate (at the bottom of the oven dashboard). The earthing conductor of the cable is the
yellow-green conductor.

Connecting the power supply cable to the mains

The appliance must be directly connected to the mains using an circuit-breaker with a minimum contact opening of 3 mm
installed between the appliance and the mains, suitable for the load indicated and complying with
current directives (the earthing wire must not be interrupted by the circuit-breaker).

The power supply cable must be positioned so that it does not exceed 50℃ more than room temperature at any point
of its length.

Before making the connections check that:

•the household circuits can support the appliance load (see data plate);

•the power supply system has an efficient earthing connection which complies with the provisions of current regulations;

•The socket or circuit-breaker is easily accessible once the cooker has been installed.

Fitting on a power supply cable

Opening the terminal board:

•Using a screwdriver, press on the side tabs of the terminal board cover;

•Pull open the cover of the terminal board

•To install the cable, proceed as follows:

•Remove the wire clamp screw and the three contact screws L-N

•Fasten the wires beneath the screw heads using the following colour scheme; Blue( N) Brown( L), Yellow- Green

•Fasten the supply cable in place with the clamp and close the cover of the terminal board.

4

Instruction on use - OBAC605M57SS

Control panel

1. Oven function selector knob

See functions on next page

2. Indicator light

3.The oven timer

To operate the timer, turn the timer knob as you wish, select time from 0~120
mins, the oven will power off when the timer stops
Set the timer at 0 if not required to prevent oven turning off expectantly

4.Oven operating light

This light will come on to indicate that the oven’s heating elements are in
operation. The light will turn off when the temperature set on the thermostat
control knob has been reached. It will cycle on and off throughout the cooking
time.

5 Thermostat/temperature control knob

The oven thermostat control knob sets the required temperature of the oven.

1

2

4

5 3

It is possible to regulate the temperature within a range of 50 - 250°C.
Turn the control knob clockwise.

5

Instruction on use - OBAC605M57SS

Selecting a cooking function and temperature

1.When your appliance is connected to your mains supply for the first
time, the power indicator light will come on, after selecting the cooking
function and setting a temperature, the operating light will come on and
the oven will start working, finally setting the cooking time;(the cooking
time is from 0min to 120mins, revolving the knob in clockwise direction to

the corresponding time on panel when setting the cooking time.

2.The oven function selector knob should be used to select the particular
mode of cooking that you require. The appliance will utilise different
elements within the oven cavity, depending on the oven function that you
select. When a function is selected, the power indicator light will come on.

No

6