Robinhood HED604FKG User Manual

Description: Robinhood Ceramic Cooktop 60cm

Model Numbers: HED604FKG

Issue 2

Warning and safety information

This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.

Do not leave this cooktop unattended or unsupervised whilst children or infirmed are present.

WARNING: Accessible parts will become hot when in use and directly after use, care should be taken to avoid
touching the burners. To avoid burns and scalds keep children away.

The installation of this cooktop is to be carried out by using only a qualified electrician.

This cooktop is to be installed in accordance with the local, national building, electrical and plumbing codes.

If the power supply cable is damaged, it must be replaced by the manufacturer or its service agent or similarly
qualified person to avoid a hazard

The cooktop is not intended to be operated by means of an external timer or separate remote-control system.

WARNING: If the glass surface is cracked, switch off the appliance to avoid the possibility of electric shock, as
the ceramic glass protects live parts.

Do not clean the oven with a steam cleaner

Installing the built in cooktop

The appliance must be installed by an qualified person in accordance with local and national building regulations.
Panels and furniture lining of the kitchen cabinet receiving the cooktop must be treated with temperature resistant

adhesives 100°C (otherwise they may become discoloured or deformed due to inadequate temperature resistance).
The cooktop is intended for installation into a benchtop above a kitchen cabinet of min 600mm width or more.
After the installation of built-in cooktop make sure that there is free access to the two fixing elements in front.
The distance between the top of the cooktop and any cabinets or rangehoods above must be no less than 600mm such

as indicated in the instructions for installation of the rangehood.
The use of hard wood decorative borders around the worktop behind the appliance is allowed, in case the minimum

distance remains as indicated on the installation illustrations.
Minimum distance between the built-in cooktop and rear wall is indicated at the illustration for the installation of the built-

in cooktop.
Induction cooktop may be installed into benchtop between 25mm to 40mm thick.
Kitchen cabinet must not have a drawer directly below cooktop. It must be fitted with a horizontal board 20mm away

from the cooktop bottom surface. Space between the plate and the cooktop must be empty and no objects may be
stored or kept there.

Rear side of the kitchen element must also have a 50mm high opening along the entire width of the element, and the
front part must have an opening of no less than 5mm .

Incorporation of the oven under the induction cooktop is permissible for ovens equipped with a cooling fan.

Installation - continued

Built in induction cooktop cutout dimensions.

A (mm) 580

B (mm) 510
C (mm) 560
D (mm) 490
E (mm) 50

F (mm) 10
G (mm) 50

HED604FKG

Installing the foam gasket

Before inserting the appliance into the opening in the kitchen benchtop, the supplied foam
gasket must be attached to the lower side of the glass ceramic (glass) cooktop between
the benchtop and cooktop.

Do not install the appliance without the foam gasket!

The gasket should be attached to the appliance in the following way:

• Remove the protective film from the gasket.

• Then, attach the gasket to the lower side of the glass, approximately 2-3mm from the edge.

• The gasket must be attached along the entire length of the glass edge and should not overlap at the corners.

• When installing the gasket, make sure that the glass does not come into contact the with any sharp objects.

Installation - continued

Installation procedure.

Worktop must be placed absolutely horizontal.

• Suitably protect the edges of the cut aperture.

• Connect the cooktop to the mains power supply (see instructions for the connection of the cooktop to the mains power

supply).

• Insert the cooktop into the cut aperture.

• Press the cooktop firmly towards the worktop from above.

Connection to the power supply.

Connections must be carried out by a qualified electrician only. The earth protection must comply with the national
regulations.

1. Connection terminals are revealed when the connection box cover is removed.

2. Prior to any attempted connection check that the voltage indicated on the rating plate is in line with your home power
supply.

• The rating plate is located underneath the appliance.

• The appliance is manufactured for use with the power supply voltage 220-240 V~.

3. The electric wiring should be equipped with a circuit breaker able to isolate the appliance from the mains in all points,
with the distance between terminals of at least 3 mm in open position. This may be done by means of fuses, safety
switches, etc.

4. The connection should be selected in accordance with the declared charge capacity of the mains and the fuse power.

5. Such appliances are allowed to be mounted on one side next to a high kitchen cabinet, the height of which may
exceed that of the appliance. On the opposite side however, only a kitchen cabinet of equal height as the appliance is
allowed.

6. Upon the completion of installation, live wires and isolated cables must be adequately protected against accidental
touching.

7. In accordance with the mains voltage, the appliance should be connected in line with the attached diagram.

8. The earth wire (PE) must be connected to the terminal marked with the earth symbol .

9. Connection may be carried out means of harmonized cables as H05V2V2-F (90°C), or with equal or better features.

10. The power cable must lead through the relief safety device, protecting it from accidental pull out.

11. Upon the completion of installation switch all the hotplates on for about 3 minutes to check the proper functioning

Attention

Only qualified electricians should attempt any repairs on the appliance, always disconnect the power supply beforehand.