Robinair Robinair AC1234-4 Manual

Download

Page 1

99 Washington Street Melrose, MA 02176

Phone 781-665-1400 Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

Original Instructions Instrucciones originales Consignes originales

Model AC1234-4

Recover, Recycle, Recharge Machine for R1234yf A/C System

Page 2

Description: Recover, recycle, and recharge machine for use with R1234yf equipped air conditioning systems.

PRODUCT INFORMATION

Record the serial number and year of manufacture of this unit for future reference. Refer to the product identication label on the unit for information.

Serial Number: _______________________________Year of Manufacture: ____________

DISCLAIMER: Information, illustrations, and specications contained in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without obligation to notify any person or organization of such revisions or changes. Further, ROBINAIR shall not be liable for errors contained herein or for incidental or consequential damages (including lost prots) in connection with the furnishing, performance, or use of this material. If necessary, obtain additional health and safety information from the appropriate government agencies, and the vehicle, refrigerant, and lubricant manufacturers.

Page 3

Table of Contents

Safety Precautions .......................2

Explanation of Safety Signal Words ............... 2

Explanation of Safety Decals. . . . . . . . . . . . . . . . . . . . . 2

Protective Devices ............................. 4

Refrigerant Tank Test ........................... 4

J2843 Requirement Regarding Lubrication .......... 4

Introduction .............................5

Technical Specications ........................5

Features ....................................6

Control Panel Functions ........................ 8

Icon Legend .................................. 9

Setup Menu Functions. . . . . . . . . . . . . . . . . . . . . . . . . 10

Initial Setup ............................ 11

Unpack the Accessory Kit .......................11

Power Up the Machine .........................11

Select Language ............................. 12

Load Language .............................. 12

Select Units .................................12

Set Date and Time ............................ 12

Edit Print Header ............................. 13

Service Vacuum .............................. 13

Adjust Background Fill Target ................... 13

Tank Fill ....................................14

Unit Activation ............................... 15

Operating Instructions ................... 16

Enter Service Data ...........................16

Recover Refrigerant from a Vehicle. . . . . . . . . . . . . . . 17

Evacuate the Vehicle A/C System ................ 18

Flushing the Hoses ........................... 19

Recharge the Vehicle A/C System. . . . . . . . . . . . . . . . 20

Automatic Function ........................... 21

System Flush ................................ 22

Maintenance ............................24

Maintenance Schedule ........................ 24

Adjust Background Fill Target ................... 25

Tank Fill ....................................25

Filter Maintenance ............................ 26

Check Remaining Filter Capacity ............... 26

Replace the Filter ........................... 27

Calibration Check ............................ 28

Change Vacuum Pump Oil .....................29

Leak Check ................................. 30

Edit Print Header ............................. 31

Replace Printer Paper ......................... 31

Install a Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Replace Oxygen Sensor in Refrigerant Identier .... 33

Refrigerant Identier .......................... 34

Replace Service Hoses and/or Service Couplers .... 35

Tank Fill Hose Filter Service .................... 35

A/C Service Function ....................37

Replacement Parts ........................... 37

Glossary ...................................37

Troubleshooting Messages ............... 38

Troubleshooting Procedures ..............42

Setup, Tank Fill & Background Tank Fill Functions

Display Message: Purity Test Failed .............. 42

Recovery Function or Automatic Function Display

Message: Purity Test Failed ....................43

Storage and Transportation of Equipment ...44

Storage .................................... 44

Transportation of Equipment .................... 44

Disposal of Equipment ...................45

Disposal of Recycled Materials ..................45

Disposal of the Machine ....................... 45

Disposal of Batteries .......................... 45

579425 REV A

Software License Notices ................. 46

Page 4

Safety Precautions

Explanation of Safety Signal Words Used in this Manual

The safety signal word designates the degree, or level, of hazard seriousness.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, could result in minor or

moderate injury. CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not

avoided, could result in property damage. These safety messages cover situations Robinair is aware of. Robinair cannot know, evaluate, or advise as to

all possible hazards. The user must verify that conditions and procedures do not jeopardize personal safety.

Explanation of Safety Decals Used on the Machine

Carefully read the instructions.

Do not use in open air in case of rain or high humidity.

Wear gloves.

Wear protection goggles.

Alternating voltage.

Grounding protection.

Electrical shock hazard.

579425 REV A

Page 5

Safety Precautions

WARNING: To prevent personal injury,

ALLOW ONLY QUALIFIED PERSONNEL TO OPERATE THE MACHINE. Before operating the machine, read and follow the instructions and warnings in this manual. The operator must be familiar with air conditioning and refrigeration systems, refrigerants, and the dangers of pressurized components. If the operator cannot read this manual, operating instructions and safety precautions must be read and discussed in the operator’s native language.

USE THE MACHINE AS OUTLINED IN THIS MANUAL. Using the machine in a manner for which it was not designed will compromise the machine and nullify the protections provided.

PRESSURIZED TANK CONTAINS LIQUID REFRIGERANT. Do not overll the internal storage vessel (ISV). Overlling can cause explosion resulting in personal injury or death. Do not recover refrigerants into nonrellable containers; use only type-approved rellable containers that have pressure relief valves.

HOSES CAN CONTAIN LIQUID REFRIGERANT UNDER PRESSURE. Contact with refrigerant can cause personal injury, including blindness and frozen skin. Wear protective equipment, including goggles and gloves. Disconnect hoses using extreme caution. Ensure the phase is complete before disconnecting the machine to prevent the release of refrigeration to the atmosphere.

AVOID BREATHING A/C REFRIGERANT AND LUBRICANT VAPOR OR MIST. Exposure can irritate eyes, nose, and throat. To remove refrigerant from the A/C system, use only equipment certied for the type of refrigerant being removed. Use the unit in locations with mechanical ventilation that provides at least four air changes per hour. If accidental system discharge occurs, ventilate the work area before resuming service.

DO NOT DISPERSE REFRIGERANT INTO THE ENVIRONMENT. Prevent the possible presence of refrigerant in the working environment.

TO REDUCE THE RISK OF FIRE, do not use the machine in the vicinity of spilled or open containers of gasoline or other ammable substances.

TO REDUCE THE RISK OF FIRE, do not use an extension cord. An extension cord can overheat and cause re. If an extension cord must be used, use the shortest possible cord with a minimum size of 14 AWG.

TO REDUCE THE RISK OF FIRE, do not use the machine in the vicinity of ames and hot surfaces. Refrigerant can decompose at high temperatures and free toxic substances to the environment that can be noxious to the user.

TO REDUCE THE RISK OF FIRE, do not use the machine in environments containing explosive gases or vapors. TO REDUCE THE RISK OF FIRE, do not use this machine in ATEX classied zones or areas. Protect the

machine from conditions that can cause electrical failure or other hazards relating to ambient interaction.

CAUTION—DO NOT PRESSURE TEST OR LEAK TEST EQUIPMENT AND/OR VEHICLE AIR CONDITIONING SYSTEMS WITH COMPRESSED AIR. Mixtures of air and R1234yf refrigerant can be combustible at elevated

pressures. These mixtures are potentially dangerous and can result in re or explosion causing personal injury and/or property damage.

HIGH VOLTAGE ELECTRICITY INSIDE THE MACHINE HAS A RISK OF ELECTRICAL SHOCK. Exposure

can cause personal injury. Disconnect power before servicing the machine.

NEVER LEAVE THE MACHINE LIVE IF AN IMMEDIATE USE IS NOT SCHEDULED. Disconnect the electrical supply before a long period of inactivity or before internal maintenance is performed.

DO NOT MODIFY THE PRESSURE RELIEF VALVE OR CHANGE THE CONTROL SYSTEM SETTINGS.

Using the machine in a manner for which it was not designed will compromise the machine and nullify the protections provided.

579425 REV A

Additional health and safety information can be obtained

from refrigerant and lubricant manufacturers.

Page 6

Safety Precautions

CAUTION : To prevent equipment damage,

TO PREVENT CROSS-CONTAMINATION, USE THIS MACHINE WITH R1234YF REFRIGERANT ONLY.

The machine is equipped with special connectors to recover, recycle, and recharge only R1234yf refrigerant. Do not attempt to adapt the machine for another refrigerant. Do not mix refrigerant types through a system or in the same container; mixing of refrigerants will cause severe damage to the machine and the vehicle air conditioning system.

DO NOT USE THIS MACHINE IN DIRECT SUNLIGHT. Position the machine far from heat sources, such as direct sunlight, which can cause excessive temperatures. The use of this machine under normal environmental conditions (10°C to 50°C) keeps pressures under reasonable limits.

DO NOT USE THIS MACHINE OUTDOORS DURING RAIN OR HIGH HUMIDITY. Protect the machine from conditions that can cause electrical failure or other hazards relating to ambient interaction.

DO NOT USE THIS MACHINE IN AREAS WHERE THERE IS A RISK OF EXPLOSION. SET UP THE MACHINE ON AN EVEN SURFACE AND UNDER SUFFICIENT LIGHTING. LOCK THE FRONT

WHEELS, AND DO NOT SUBJECT THE MACHINE TO VIBRATION. TO AVOID CHEMICAL INCOMPATIBILITIES WITH THE INTERNAL COMPONENTS OF THE MACHINE,

USE ONLY OILS APPROVED BY THE VEHICLE MANUFACTURER. Problems resulting from the use of

non-approved oils will void the warranty.

Additional health and safety information can be obtained

from refrigerant and lubricant manufacturers.

Protective Devices

The machine is equipped with the following protective devices:

• Over pressure valves.

• A maximum pressure switch stops the compressor when excessive pressure is sensed.

WARNING: Tampering with these protective devices could result in serious injury.

Refrigerant Tank Test

Ofcial records and recurring tests necessary for pressurized instruments are governed by laws and/or national regulations dependent upon the country where the refrigerant tank is used. The system manager is responsible for compliance with laws, regulations, and technical rules. During normal service, refrigerant tanks do not need maintenance. Refer to the Maintenance section of this manual for more information.

J2843 Requirement Regarding Lubricant

Only new lubricant, as specied by the system manufacturer, shall be installed in the MAC System. Lubricant removed from the system and/or the equipment shall be disposed of in accordance with the applicable federal, state and local procedures and regulations.

579425 REV A

Page 7

This machine is used on R1234yf equipped vehicles and is designed to be compatible with existing service equipment and standard service procedures. This machine is a single-pass system (i.e. refrigerant ows through a lter once) that meets specications for recycled refrigerant. Follow recommended service procedures for the containment of R1234yf

In order to meet the SAE J2843 specication for a machine that is capable of servicing both conventional belt-driven compressors and the high-voltage electric compressors found on hybrid vehicles, the internal oil charge feature has been removed, and both service hose ush and vehicle A/C system ush features have been added.

The unit includes a 1.5 cfm (42 l/m) high-vacuum pump for fast, thorough evacuation. The compressor pulls the A/C system to 0 psig, then works in series with the vacuum pump to achieve highly efcient recovery and immediate recharge. If the system is not opened for service, there is no need to pull additional vacuum. If the system is opened for service, use the unit’s vacuum cycle to remove air and moisture from the A/C system. (A minimum 10-minute vacuum is recommended, or follow the vehicle manufacturer’s specications.)

Introduction

CAUTION: R1234yf systems require special oils. To prevent

equipment damage, refer to the A/C system manufacturer’s service manual for oil specications.

Technical Specications

Dimensions .................107 cm x 56 cm x 80 cm

Display ...........5 × 9 cm (4.3-in. diag) graphical LCD

Filter ..............................150 kg (330 lb)

Humidity . . 10-50°C (50-122°F), 86% RH non-condensing

Manometer ......................Ø 100 mm (3.9 in.)

Maximum Pressure . . . . . . . . . . . . . . . . . 31 bar (450 PSI)

Noise .................................<70 dB(A)

Nominal Voltage

AC1234-4 ..........................115V, 60 Hz

Oil Bottle Capacity. . . . . . . . . . . . . . . . . . . .355 ml (12 oz)

Operating Temperature ...10°C to 50°C (50°F to 122°F)

Power Consumption ...................... 1380 VA

Vacuum Pump Free-Air Displacement

.......................1.5 CFM (42 L/m) @ 60 Hz

Service Hoses ..................2.74 m / SAE J2886

Tank Capacity .....................9.5 kg (20.94 lb)

Weight .............................82 kg (176 lb)

579425 REV A

Page 8

Introduction

Features

579425 REV A

Page 9

Introduction

Item

No.

1 Oil Drain Bottle

2 Printer Cap

3 Low-side (blue) and High-side (red) Manifold Gauges

4 Graphic Display and Keypad

6 Vacuum Pump Oil Sight Glass

7 Vacuum Pump Oil Drain Fitting

8 Power Switch

9 Wheel Lock

10 Vacuum Pump Oil Fill Cap and Port

(detailed view shown without protective cover)

USB and SD Card Connections

Description

11 Contamination Recovery Port

12 Service Hoses

13 Service Hose Storage Ports

14 Power Cord

579425 REV A

Page 10

Introduction

Control Panel Functions

ARROW UP highlights the previous item. ARROW DOWN highlights the following item. ARROW RIGHT scrolls to next screen. ARROW LEFT scrolls to previous screen. SELECTION ARROWS make a selection or answer a query.

Control Panel Keypad

579425 REV A

Page 11

Icon Legend

Introduction

AUTOMATIC ICON

Pressing the key under this icon will enter the automatic refrigerant recovery, vacuum, and charge process.

RECOVER ICON

Pressing the key under this icon will enter the refrigerant recovery process.

VACUUM ICON

Pressing the key under this icon will enter the system vacuum process.

CHARGE ICON

Pressing the key under this icon will enter the refrigerant charge process.

NEXT/FORWARD ICON

Pressing the key under this icon will

proceed to additional menu selection options, or proceed to an additional

step in a function or process.

BACK ICON

Pressing the key under this icon will return to previously seen menu selection options, or return to the previous screen within a function or process.

HELP ICON

Pressing the key under this icon will provide help and information corresponding to the current screen and/ or function being viewed or performed.

DATABASE ICON

Pressing the key under this icon will enter the vehicle database retrieval process.

SETUP MENU ICON

Pressing the key under this icon will enter the Setup Menu.

RETRY ICON

Pressing the key under this icon will retry the current process or function.

CHARGE PATH SELECTION ICON

Pressing the key under this icon will toggle the desired path of refrigerant charge between high side, low side, and both side.

ON/OFF ICON

Pressing the key under this icon will toggle the highlighted function on or off as desired.

BACKSPACE ICON

Pressing the key under this icon will delete a text character to the left of the current selection.

PAUSE ICON

Pressing the key under this icon will pause the current process.

RESUME ICON

Pressing the key under this icon will resume a process that has been paused.

PRINT ICON

Pressing the key under this icon will print a summary corresponding to the current completed process.

DELETE ICON

Pressing the key under this icon will delete a selected entry from the memory of the machine.

CHANGE UNITS ICONS

Pressing the key under one of these icons will toggle the unit of measurement for the current entry eld.

579425 REV A

YES/ACCEPT ICON

Pressing the key under this icon will accept any choices made on the current screen and proceed to the next step of the function.

NO/CLOSE ICON

Pressing the key under this icon will reject any choices made on the current screen and return to the previous step of the function or the Main Menu.

Page 12

Introduction

Setup Menu Functions

Access the following functions by pressing the Menu key and selecting Setup.

Calibration Check

Use to verify internal scale calibration. Refer to Calibration Check in the Maintenance section of this user manual.

Edit Print Header

Programs information that will appear on the printout each time a print function is used.

Filter Maintenance

The lter removes acid, particulates, and moisture from the refrigerant. To meet requirements, it is mandatory to replace the lter after 150 kg (330 lb) of refrigerant has been ltered.

This menu item displays the lter capacity remaining until the machine locks down and no longer functions. Refer to Filter Maintenance in the Maintenance section.

Flush Hoses

Flushes residual oil from the machine’s service hoses to prepare for service of next vehicle.

Production Menu

For Robinair production use only.

Pump Maintenance

Displays the amount of time remaining until the next vacuum pump oil change is needed. For maximum vacuum pump performance, change vacuum pump oil every time the lter is replaced. Refer to the Change Vacuum Pump Oil in the Maintenance section.

Refrigerant Management

Displays the amount of refrigerant recovered, charged, and replenished (for the life of the machine), and ltered since the last lter change.

Select Language

Select a language for screen prompts. English is the default language.

Service Menu

For Robinair service center use only.

Vacuum Default Time

Program machine with a value to use as a default time during vacuum service.

Replace Service Hoses

Use to replace service hoses on the machine.

Select Units

Program the machine to display units of measure.

Date and Time

Program the machine for current date and time.

System Flush

Provides a method of removing oil by forcing liquid refrigerant through an A/C system or components of an A/C system. After ushing, the refrigerant is recovered by the machine and ltered by the recycling circuit.

System Information

Displays the revision level of the software in the machine.

Tank Fill

Use this Setup Menu item to transfer refrigerant from a source tank to the ISV. The tank ll value may be adjusted up or down to suit the user’s needs. Refer to Tank Fill in the Maintenance section.

Unit Activation

Failure to register and activate the machine within 30 days of initial startup will cause the machine to lock out and no longer function. Select this Setup Menu item and follow the prompts before the trial period expires.

View Service Data

Displays vehicle information that was entered into the Enter Service Data screen. Vehicles are displayed by date of service and VIN number. The database stores 25 VIN entries.

Hose Equalize

Use this Setup Menu item to recover refrigerant from the service hoses back into the vehicle A/C system. This item is useful after performing diagnostics which do not require the need to recover the A/C system into the RRR machine. The user will be prompted to connect the low side service hose to the appropriate port and to start the vehicle’s A/C system on max.

Adjust Background Fill Target

Program the machine with a value to set as the automatic ll amount when the machine is idle.

Note: Requires external connection to the tank ll hose.

579425 REV A

Page 13

Unpack the Accessory Kit

Unpack the accessory kit from the box, and remove the plastic packaging.

Calibration Check

Weight

533 g (1.18 lb)

Tank Fill Hose Adapter

Pouch containing the user manual, SDSs, EPA

information, MACS information, and a service center list.

Initial Setup

WARNING: To prevent personal injury while working with refrigerant, read and follow the instructions and warnings in this manual, and wear protective equipment such as goggles and gloves.

IMPORTANT:

• This procedure can take several hours. Perform this initial setup procedure BEFORE the machine is needed for its rst vehicle A/C service.

• During initial setup, the machine prompts through the following steps. Any changes to these settings after the initial setup can be completed through the Unit Setup menu.

Power Up the Machine

1. Unwind the power cord from the handle, and plug it into a correct voltage, grounded outlet.

2. Position the machine so the plug and the power switch are of easy access for the operator. Verify the fan vents on the rear of the machine are not obstructed.

3. Lock the front wheels.

4. Toggle the power switch on the control panel to turn the machine ON.

The machine launches into the initial Setup mode.

CAUTION: The machine is programmed

to run the setup procedure as outlined here. To prevent personal injury, do NOT operate the machine without the oil ll port installed because the vacuum pump is pressurized during normal operation.

579425 REV A

Page 14

Initial Setup

Select Language

The operator selects the language for the screen prompt displays. English is the default language.

1. Use the UP or DOWN arrow key to toggle through the

available languages one line at a time.

2. Select

Note: To update an existing language or to add a new language, refer to Load Language in the Maintenance section of this manual.

to set the selected language.

Load Language

Use the following instructions to add or update a language from an SD card.

1. Choose SELECT LANGUAGE from the SETUP MENU.

2. Use the arrow keys to scroll to LOAD NEW. Select

3. Insert the SD card containing the language data into the side panel on the machine. See Figure 1.

4. Follow the prompts to select the language to load or update. If loading a new language, select which language to replace.

Select Units

The operator sets the display for units of measure. Metric is the default.

Insert SD card containing new or updated language.

Figure 1

1. Use the ARROW UP or ARROW DOWN key to toggle Imperial or Metric units.

Note: If Imperial is selected, weights will be displayed in Metric units (per SAE standard J2843); pressures and temperature will be displayed in Imperial units.

2. Select

to choose the displayed unit of measure.

Set Date and Time

Use the arrow keys to move the cursor. Use the keypad to modify the information displayed.

1. Use the ARROW UP and ARROW DOWN keys to select which item to change: day, month, year, or time. Select

to toggle between AM and PM.

2. Use the multi-tap interface on the numeric keypad to modify the information.

3. Select

to save.

579425 REV A

Page 15

Edit Print Header

This machine has the capability to store recovery, vacuum, charge, and ush information for up to 25 vehicles. The information loaded into Edit Print Header will appear on each printout.

1. Enter text by using the arrows and the multi-tap interface

on the numeric keypad:

Initial Setup

WARNING: To prevent personal injury while working with refrigerant, read and follow the instructions and warnings in this manual, and wear protective equipment such as goggles and gloves.

• ARROW LEFT and

• ARROW RIGHT moves the cursor to the right.

• 0 (ZERO) acts as a spacebar when pressed twice.

• ARROW UP and DOWN navigate between the rows.

2. Select

to the previous header without saving data.

to save/exit the function; select to return

key act as backspace key.

Service Vacuum

At this point the machine clears its internal plumbing before proceeding with setup.

1. Check the vacuum pump oil level sight glass and verify

the oil level is at the center of the sight glass.

2. When prompted, connect the service hoses from the

machine to their storage ports as shown in Figure 2.

Select

3. The machine enters a 5-minute vacuum and will automatically

enter the next set-up process when complete.

to continue.

Service Hoses

Connected to

Storage Ports

Figure 2

Adjust Background Fill Target

This machine possesses a background tank ll feature. An external refrigerant storage vessel can be uidly connected to the machine (using the black tank ll hose) for a continuous topping off of the internal storage vessel. Drawing from the refrigerant within the connected external storage vessel, the machine will periodically charge the ISV tank to the desired ll target.

Using the arrows and the numeric keypad, enter the desired ll target (default amount is 3.6 kg).

579425 REV A

Page 16

Initial Setup

Tank Fill

This procedure transfers refrigerant from a source tank to the internal storage vessel (ISV) in the machine. The maximum capacity of the ISV is 9.5 kg (21 lb). Use arrow keys to move the cursor; use the keypad to enter a value.

1. The machine displays elds for desired tank ll amount, charge capacity, and the amount of recoverable refrigerant (recover capacity) within the internal storage vessel. Enter the desired tank ll amount.

Note: Add at least 3.6 kg of refrigerant to ensure enough is available for charging.

2. Connect the tank ll (black) hose to the liquid connector on the source tank.

3. Open the source tank valve.

4. Position the source tank in such a way that liquid refrigerant is supplied to the connection.

5. Select tank to verify that it is R1234yf and not contaminated.

6. Select lling the internal storage vessel (ISV). Add at least 3.6 kg of refrigerant to ensure enough is available for charging. This process takes 15–20 minutes.

. The machine checks the refrigerant in the source

to start the tank ll process. The machine begins

Note: Charge Capacity: The amount of refrigerant

in the ISV that can be charged into a vehicle A/C system.

Recover Capacity: The amount of additional refrigerant that could be recovered into the ISV.

7. The machine stops when the designated amount of refrigerant has been transferred to the ISV or when the source tank is empty. Follow the messages on the display.

8. Close the source tank valve.

9. Select

The machine is ready for operation.

Note:

• There is no need to calibrate the scale; it is calibrated at the factory.

• After the tank ll process is complete, the display does

not show the same amount as the programmed ll level.

The display shows the amount of refrigerant that is available for charging, which is approximately 0.67 kg (1.4 lb) less than the total amount of refrigerant in the tank.

to return to the Setup Menu.

579425 REV A

Page 17

Unit Activation

Failure to register and activate the machine within 30 days of initial startup will cause the machine to lock out and no longer function.

1. Select Unit Activation from the Setup Menu. The

machine displays

XX Days Left on Trial Period to activate unit. Activate Now?

2. Select to start the activation process. The machine

displays

Product Activation

Personal product code: XXXXXXXXXXX

Enter code: XXXXXXXXXXXX

Initial Setup

3. Open a web browser on a personal computer and

enter https://register.servicesolutionsportal.com.

4. Enter the user name and password, and log in to the

website.

Note: If a rst-time user, select REGISTER to create

a user name and password.

5. On the personal computer, enter the Personal Product

Code of the machine into the Product Activation key box on the website to receive an activation code.

6. On the machine, enter the activation code into the

correct eld. Note: Enter the code exactly as received. Capitalization is required.

7. Record the activation code on a piece of paper and

le it in a secure place. Select

8. The machine displays

Activation successful.

Select . The machine has been activated.

579425 REV A

Page 18

Operating Instructions

Enter Service Data

After selecting any service function, information about the vehicle may be entered into and stored in the machine’s database.

The machine displays

Enter service data new

1. Select to enter a new record, or scroll to select a previously serviced vehicle and then select . The highlighted selection will be in red. The machine displays

Enter service data VIN: _____________________________ Mileage: _______________________ Make: ___________________________ Model: _________________________

2. Use the arrow keys to move between rows and the multitap keypad to enter text.

Information entered on this screen is stored by date and vehicle identication number (VIN). The database stores the latest 25 entries, with the most recent at the top of the list.

The information will also appear on service summary printouts.

579425 REV A

Page 19

Operating Instructions

Recover Refrigerant from a Vehicle

1. Empty the oil drain bottle before starting a recovery.

Remove the oil drain bottle from the machine by pulling the bottle straight down—do not use a twisting or rocking motion. Reinstall the oil drain bottle. See Figure 3.

2. Connect the high-side (red) and low-side (blue) service

hoses to the vehicle A/C system.

3. Open the coupler valves on the hoses by turning the

collars clockwise.

WARNING: To prevent personal injury while working with refrigerant, read and follow the instructions and warnings in this manual, and wear protective equipment such as goggles and gloves.

4. Select RECOVER

5. The machine will enter the service data entry form. Enter

all applicable data and select checks the refrigerant in the vehicle to conrm that it is R1234yf and not contaminated. If the refrigerant purity is acceptable, the machine begins the recovery process. A clicking noise indicates the solenoid is opening and closing — this is normal.

The machine runs a self-clearing cycle to clear any internal refrigerant from its internal plumbing.

System recovery begins and includes a timed vacuum, deep recovery process.

After recovery, the machine will perform an oil drain, which may require up to 90 seconds to complete.

6. After the oil drain is complete, a summary is displayed

showing the total amount of refrigerant recovered. The user is prompted to “Check Oil Drain Bottle” to note amount of oil drained. Recovery information can be printed by selecting

7. Select

Note: The displayed recovered weight can vary depending on ambient conditions and should not be used as an indicator of scale accuracy.

on machines equipped with a printer.

to return to the Main Menu.

from the MAIN MENU.

to continue. The machine

Oil Drain

Bottle

Note: The amount of oil that was removed from the A/C system is the amount of new oil that should be charged into the A/C system after evacuation is complete.

• Only new lubricant, as specied by the system manufacturer, shall be installed in the MAC System. Lubricant removed from the system and/or the equipment shall be disposed of in accordance with the applicable federal, state and local procedures and regulations.

579425 REV A

Figure 3

Page 20

Operating Instructions

Evacuate the Vehicle A/C System

1. Connect the service hoses to the vehicle’s service ports.

2. Open the service hose coupler valves by turning the collars clockwise.

WARNING: To prevent personal injury while working with refrigerant, read and follow the instructions and warnings in this manual, and wear protective equipment such as goggles and gloves.

3. Select VACUUM

4. Select Vacuum Leak Check, if desired, to automatically perform a 5-minute pressure rise leak check after the vacuum.

5. Select or enter a desired vacuum time using the number keys.

Note: The vacuum process will halt if pressure rises above .35 bar (5 psi). Recover refrigerant before proceeding.

The machine pulls a vacuum on the A/C system for the programmed amount of time.

Vacuum information can be printed by selecting machines equipped with a printer.

6. Select

to accept the 10-minute default evacuation time,

to return to the Main Menu.

from the MAIN MENU.

579425 REV A

Page 21

Operating Instructions

Flushing the Hoses

If the next vehicle to be serviced contains a different type of oil than the previous vehicle serviced, it is recommended the service hoses be ushed of residual oil to prevent contamination.

1. Select FLUSH HOSES from the SETUP MENU. The

machine displays

Connect service hoses to storage ports and open coupler valves.

2. Connect the service hoses to the machine’s storage port

connections as shown in Figure 4.

3. Open the service hose coupler valves by turning the

collars clockwise.

4. Select

three minutes, followed by a recovery. When the hose ushing process is compete, the display

reads

FLUSH HOSES Complete

5. Select to return to the Setup Menu.

6. Close the coupler valves by turning the collars

counterclockwise.

to begin the hose ush process, which runs for

Storage

Port

Connections

Figure 4

579425 REV A

Page 22

Operating Instructions

Recharge the Vehicle A/C System

The following tests are automatic and are performed as required by SAE J2843:

• Vacuum test that runs 5-20 minutes to achieve the correct level

• 5-minute vacuum rise test

• 15% charge

• Manual leak test using a leak detector certied to SAE J2913

Notes:

• J2843 leak testing is intended to nd a gross leak before charge, for safety reasons. It is not intended to take the place of other established leak test practices.

• The 15% charge is automatically recovered before recharging the programmed amount.

• To avoid false failures, the temperatures of the vehicle system and the recovery machine should be within ±5°C.

1. Select CHARGE The display shows

Is the service being performed on a system with an electric compressor using POE oil?

2. If the system does NOT have an electric compressor with POE oil, select to continue. If the system has an electric compressor with POE oil, select to ush all residual oil from the hoses. The user will be prompted to “Connect service hoses to storage ports and open coupler valves.” See Figure 4 on page 19. Continuing will begin the process of ushing the hoses. Once complete, select

to continue through the Charge process.

3. The user will be prompted to enter service data. Select

once complete to continue. The display shows

Charge: XX.XXX kg on High Side

from the MAIN MENU.

6. Using the arrow keys, maneuver to the charge path selection. High Side is default. To change, select panel. This will allow the user to toggle between high, low, and both side charge paths. The current selection is indicated on the display.

7. Select Moving or bumping the machine at this point may result in an inaccurate charge. When the charge cycle approaches the desired weight value, the machine slows down. It will charge, settle, charge again, settle, etc.

8. When prompted, select equalization. Select to perform hose compensation.

Note: Hose equalization requires the user to start the vehicle. Hose compensation adds a preset amount of refrigerant to the chart to compensate for service hose volume.

9. When the CHARGE COMPLETE screen appears, it includes a summary of charge results. The user may select summary, if a printer is installed. Select to proceed to clear the service hoses.

10. The user will be prompted to close the coupler valves and disconnect the hoses from the vehicle. Select remaining refrigerant from the hoses. Once the hose clear is complete, the machine will return to the Main Menu.

The vehicle A/C system is now ready for use.

to start the charge process.

on the control

to perform hose

to print the

to recover any

4. Connect both service hoses to the vehicle’s service ports and open coupler valves.

5. Use the arrow keys and the numeric keypad to enter the desired charge amount. Select

to change units.

579425 REV A

Page 23

Operating Instructions

Automatic Function

The AUTOMATIC function allows a user to perform an automatic recovery, vacuum, leak test, and/or charge sequence. A total automatic sequence may take up to an hour to complete.

1. Connect high-side (red) and low-side (blue) service hoses

to the A/C system.

2. Open the service hose coupler valves by turning the

collars clockwise.

3. Select AUTOMATIC

shows

from the MAIN MENU. The display

WARNING: To prevent personal injury while working with refrigerant, read and follow the instructions and warnings in this manual, and wear protective equipment such as goggles and gloves.

10. The user will be prompted to close the coupler valves and disconnect the hoses from the vehicle. Select remaining refrigerant from the hoses. Once the clear is complete, the machine will return to the Main Menu.

The vehicle A/C system is now ready to use.

to recover any

Vacuum Time: XX:XX Vacuum Leak Test: ON Charge: XX.XXX kg on High Side

4. Use the numeric keypad to enter the desired length of vacuum.

5. Using the arrow keys, maneuver downwards to choose whether to perform a vacuum leak test or not. ON is the default setting. To toggle, select

6. Use the arrow keys and the numeric keypad to enter the desired charge amount.

7. Using the arrow keys, maneuver to the “charge path selection.” High Side is default. To change, select on the control panel. This will allow the user to toggle between high, low, and both side charge paths. The text on the display will change to the current selection.

8. Select now automatically proceed through all applicable functions: RECOVER, VACUUM, and CHARGE. If the vehicle being serviced has previously undergone a recover and vacuum procedure, the machine will only perform a CHARGE.

to begin the AUTOMATIC cycle. The unit will

on the control panel.

Notes:

• The CHARGE function for vehicles

equipped with a single-service fitting

should be carried out manually according to procedures in the vehicle manufacturer’s service manual.

• After the RECOVER process, the user

will be prompted to “Check oil bottle and enter oil to be added.” The amount of oil added should be equal to the amount of oil drained and can be found by looking at the graduations on the drain bottle.

• If problems are encountered during the automatic sequence, an audio alert sounds three times. The sequence remains paused until the user enters a decision regarding how to proceed.

9. When the AUTOMATIC COMPLETE screen appears, it

includes a summary of results. The user may select to print the summary, if a printer is installed. Select to proceed.

579425 REV A

Page 24

Operating Instructions

System Flush

The following tests are automatic and are performed as required by SAE J2843:

• Vacuum test that runs 5-20 minutes to achieve the correct level

• 5-minute vacuum rise test

• 15% charge

• Manual leak test using a leak detector certied to SAE J2913

Notes:

• J2843 leak testing is intended to nd a gross leak before charge, for safety reasons. It is not intended to take the place of other established leak test practices.

• The 15% charge is automatically recovered before recharging the programmed amount.

WARNING: To prevent personal injury while working with refrigerant, read and follow the instructions and warnings in this manual, and wear protective equipment such as goggles and gloves.

• To avoid false failures, the temperatures of the vehicle system and the recovery machine should be within ±5°C.

The SYSTEM FLUSH function is performed using a vehicle manufacturer-approved flushing adapter. Refer to the instructions included with the adapter while the following steps are performed.

1. Verify the usher lter and strainer are not plugged.

2. Mount the usher to the rear of the machine.

3. Remove the oil drain bottle (see Figure 5) from the Robinair machine. Drain the oil bottle, and dispose of the oil according to applicable regulations. Reinstall the oil drain bottle on the machine.

4. Recover all refrigerant from system to be ushed.

5. Note the amount of oil collected during recovery. This amount must be replaced, as well as any oil collected during ush.

Note: The amount of oil collected and reported during

system ush does not include the amount of oil collected

during the initial recovery.

Oil Drain

Bottle

Figure 5

6. Verify there are at least 6.0 kg (13.2 lb) of refrigerant in the machine. The machine will not be able to complete a system ush without at least 6.0 kg of refrigerant in the ISV.

Note: If the machine does not have at least 6.0 kg

(13.2 lb) of refrigerant on-board, see “Tank Fill” on page 14.

7. Disconnect the machine from the vehicle.

8. Refer to the vehicle service manual, and connect the appropriate ushing adapters and bypasses.

579425 REV A

Page 25

Operating Instructions

9. Connect the low-side (blue) service hose directly to the

lter of the ushing kit.

10. Remove the high-side (red) service coupler, and connect

the high-side (red) service hose to the system suction line adapter.

11. Use the supplied hose to connect the system discharge

adapter to the usher inlet.

12. Connect hoses according to the instructions included

with the ush kit.

13. Select SYSTEM FLUSH from the SETUP MENU. The unit

will prompt for any service data entry, if desired. Select

to continue to the system ushing process. The user may be prompted to enter in a total Flush Time depending upon which ush process is enabled.

The machine will then automatically enter the VACUUM process and proceed to a leak test.

Once the vacuum and leak tests are completed, the unit will enter the actual system ushing process, followed by an oil drain.

14. When the Flush Complete screen appears, it includes a system ush result summary. The user may select to print the summary, if a printer is installed. Select to return to the SETUP MENU.

The vehicle A/C system has been ushed.

WARNING: Do NOT disconnect service

couplers during the ushing process. Refrigerant could spray out of the ttings,

and exposure may cause personal injury.

CAUTION: The ushing kit has a replaceable

lter as well as a debris strainer, both of

which can get plugged. At the end of the

ush cycle, check the high-side (red)

gauge for system pressure, and check the adapter for complete removal of refrigerant.

If pressure exists or refrigerant remains, exit

the ushing cycle and enter the recovery

mode to recover refrigerant through both the high-side (red) and low-side (blue)

hoses. Then service the lters and repeat the ush process.

579425 REV A

Page 26

Maintenance

Maintenance Schedule

Maintenance Task Recommended Interval

Change lter

Change vacuum pump oil

After 150 kg (330 lb) of refrigerant has been ltered. Refer to Filter Maintenance in the Maintenance section of this manual.

When the lter is replaced. Refer to Change Vacuum Pump Oil in the Maintenance section of this manual.

Change refrigerant identier sample hose

Check casters and wheels for ease of operation Monthly.

Check internal scale calibration

Check machine for leaks

Clean airow outlet panel (see Figure 6) Monthly. Use a clean cloth.

Clean cabinet and control panel Monthly. Use a clean cloth. Inspect power cord and hoses for cuts and abrasions Daily. Lubricate wheel bearings and inspect brake components Monthly.

Pressure Test

Airow

Outlet

When lter is replaced, refer to Refrigerant Identier section of this manual.

Monthly. Refer to Calibration Check in the Maintenance section of this manual.

Monthly. Check hoses and connections for leakage. Disconnect power, remove the shroud, and use an electronic leak detector to check ttings.

Every 10 years. Performed by an authorized Robinair service center.

WARNING: To prevent personal injury

only qualied personnel may perform

inspections and repairs to this machine. Read and follow instructions and warnings in this manual, and wear protective equipment such as goggles and gloves.

Figure 6

579425 REV A

Page 27

Adjust Background Fill Target

1. Select ADJUST BACKGROUND FILL TARGET in the SETUP MENU.

2. Using the arrows and the numeric keypad, enter the desired ll target. Select exit. Select to exit and continue to use the previously entered amount.

to save the new value and

Tank Fill

Maintenance

WARNING: To prevent personal injury while working with refrigerant, read and follow the instructions and warnings in this manual, and wear protective equipment such as goggles and gloves.

This menu item is used to transfer refrigerant from a source tank to the ISV.

The maximum capacity of the internal storage vessel (ISV) is 9.5 kg (21 lb). Use the arrow keys to move the cursor; use the keypad to enter a value.

Note: Add at least 3.6 kg of refrigerant to ensure sufcient

refrigerant is available for charging.

1. Connect the tank ll (black) hose to the liquid connector on a full source tank.

Note: Tank ll hose and tank access port have left-handed

threads.

2. Position the source tank in such a way that liquid refrigerant is supplied to the connection. Open the source tank valve and verify that the tank does not restrict airow from the vent.

3. Select TANK FILL from the SETUP MENU. The machine displays

Tank Fill Fill Amount: XX.XYY Charge Capacity: XX.XXYY Recover Capacity: XX.XXYY

5. The machine begins lling the ISV and automatically stops when the preset tank ll level is reached. To stop the tank ll before the preset level is reached, select option to exit will appear on the display.

6. Once complete, remove the hose from the source tank.

. An

4. Enter the quantity to recover, and select . The machine checks the refrigerant in the source tank to verify that it is R1234yf and not contaminated.

Note: Add at least 3.6 kg of refrigerant to ensure sufcient

refrigerant is available for charging.

579425 REV A

Page 28

Maintenance

Filter Maintenance

The lter is designed to trap acid and particulates, and to remove moisture from refrigerant. To meet the mandate for adequate moisture and contaminant removal, the lter must be replaced after 150 kg (330 lb) of refrigerant has been ltered.

The machine gives a warning when 100 kg (220 lb) of the lter capacity has been used; the machine locks down when the 150 kg (330 lb) lter capacity has been reached and will no longer function.

Check Remaining Filter Capacity

1. Select FILTER MAINTENANCE from the SETUP MENU

or when the machine prompts. The machine displays

Remaining Filter Capacity: XXX.X kg Replace lter now?

The machine displays the amount of lter capacity remaining until the machine locks down.

WARNING: To prevent personal injury while working with refrigerant, read and follow the instructions and warnings in this manual, and wear protective equipment such as goggles and gloves.

2. Select the machine.

WARNING: The components in the machine are under

high pressure. To prevent personal injury, change the

lter only when the machine prompts.

to change the lter; select to resume using

579425 REV A

Page 29

Replace the Filter

Maintenance

1. If was selected to change the lter, the machine prompts

for the new lter code to be entered.

Enter new lter serial number

Use the keypad to enter the serial number that appears on the new lter, and select to continue.

Note: If “Invalid serial number” is displayed, the serial

number has been incorrectly entered, or the lter has

already been used in this machine.

2. The machine clears the existing lter and displays

Serial number accepted. Turn power off and replace lter.

Turn off the machine. Remove the oil bottle. Remove the four screws holding the shroud. See Figure 7.

3. Hang the shroud on the back of the machine as shown

in Figure 8.

4. Remove the lter by turning it counterclockwise (as viewed

from the bottom of the lter).

5. Look at the new lter. Verify both o-rings are lubricated

and correctly located in the grooves.

Remove the four screws holding the shroud.

Figure 7

6. Install the new lter by threading it clockwise into place.

Verify the lter is positioned correctly as shown in Figure 8. Tighten the lter to 20 Nm.

7. Power the machine on. The Change Vacuum Pump Oil

operation will begin, and the screen will display

Warming oil for drain XX:XX

See “Change Vacuum Pump Oil” procedure in this manual for more information.

The machine will then begin the Leak Check operation. See the “Leak Check” procedure in this manual for more information.

Caution: To prevent equipment damage, use only

authentic Robinair No. 34724 lters in this machine. All

performance tests and claims are based on using this

specic lter.

Hang Shroud

Here

Filter

579425 REV A

Figure 8

Page 30

Maintenance

Calibration Check

This function is used to ensure the machine’s internal scale is always calibrated. During this test, use only the calibration weight that is provided with the machine.

1. Refer to Figure 9, and verify the magnet on the bottom of the machine is clean.

2. Select CALIBRATION CHECK from the SETUP MENU. The machine displays

Place calibration weight onto the magnet located on the bottom of the machine.

3. Attach the calibration weight to the magnet on the bottom of the machine. Select to continue.

4. The machine displays

Remove calibration weight from the magnet located on the bottom of the machine.

Remove the calibration weight from the magnet. Select

to continue.

• If the display shows

Calibration check passed

the scale is in calibration. Select to return to the Setup Menu.

• If the display shows

Calibration check failed. Retry?

the scale is out of calibration. To retry, select . If calibration continues to fail, contact an authorized Robinair service center for assistance.

Magnet

Figure 9

579425 REV A

Page 31

Change Vacuum Pump Oil

1. Select PUMP MAINTENANCE from the SETUP MENU or

when prompted. The display shows how long the vacuum pump has operated since the last oil change.

Remaining oil life: XXX:XX (hhh:mm) Change oil now?

Maintenance

WARNING: To prevent personal injury,

do NOT operate the machine at any other

time without the oil ll port cap installed,

because the vacuum pump is pressurized during normal operation.

2. Select to change vacuum pump oil. If the machine

displays

Warming oil for drain XX:XX

allow the vacuum pump to run for up to two minutes to warm up the oil. If the oil is already warm, the display shows:

Drain used oil from pump and replace with 150 ml of new oil Remove ll cap to speed draining of oil

while the compressor runs to eliminate any pressure in the vacuum pump.

3. After the compressor stops, slowly open the oil ll cap to

verify there is no pressure in the machine. Then carefully remove the cap. See Figure 10.

4. Remove the oil drain tting cap and drain the oil into a

suitable container for disposal. Replace the cap and close tightly. Slowly add 150 ml of vacuum pump oil to pump through oil ll port. Select

5. The machine displays

to continue.

Oil Fill Cap

and Port

Sight

Glass

Oil Drain

Fitting

Figure 10

Fill vacuum pump to the center of the sight glass Reinstall ll cap

Slowly add vacuum pump oil to the pump through the oil ll port until the oil reaches the center of the sight glass. Install the cap on the oil ll port and close tightly. Select

to return to the SETUP MENU.

Note: For proper oil level, ensure the machine is on a at,

level surface.

579425 REV A

CAUTION: It is the responsibility of the user to monitor vacuum pump oil level and clarity. If contaminated oil is not removed from the vacuum pump and replaced, the vacuum pump will be permanently damaged.

Page 32

Maintenance

Leak Check

A leak test may be performed on the machine at any time. During this test, components containing refrigerant are pressurized and monitored for pressure decay, which could indicate a leak.

1. Select LEAK CHECK from the SETUP MENU. The machine displays

Connect service hoses to storage ports and open coupler valves

2. Connect the service hose couplers to the storage ports at the rear of the machine. Open the couplers by turning the collars clockwise.

WARNING: To prevent personal injury while working with refrigerant, read and follow the instructions and warnings in this manual, and wear protective equipment such as goggles and gloves.

3. Select and displays

Recover in progress

The machine performs a 30-second vacuum test and displays

Vacuum leak check in progress

If the vacuum test fails, the machine will prompt to check for leaks.

Once the machine passes the vacuum test, a controlled pressure is applied to its internal components. The machine displays

Pressure leak check in progress

Pressure is held for ve minutes and monitored for decay. Minutes and seconds count down on the display.

• If an acceptable pressure decay is detected, the

• If an unacceptable pressure decay is detected, the

to start. The machine performs a self-recovery

machine recovers refrigerant and returns to the Setup Menu, ready for normal operation.

machine will prompt to check for leaks. Take the machine to an authorized Robinair service center for repair.

WARNING: To prevent personal injury should the machine require transport to a local Robinair service center, follow local government regulations regarding transportation of equipment containing R1234yf.

579425 REV A

Page 33

Edit Print Header

To make changes to text that appears in this screen:

1. Select EDIT PRINT HEADER from the SETUP MENU.

2. The cursor is in the rst eld. Update the text by using the arrows and the multi-tap interface on the numeric keypad:

Maintenance

• ARROW LEFT and

• ARROW RIGHT moves the cursor to the right.

• ZERO (0) key acts as a spacebar.

• ARROW UP and DOWN navigate between the rows.

3. Select Menu; select to return to the previous header and exit

to the Setup Menu.

to save the changes and return to the Setup

act as a backspace key.

Replace Printer Paper (if equipped)

To install a new paper roll in the printer:

1. Remove the cover on the printer by pulling out on the tab as shown in Figure 11.

2. Remove the paper core.

3. Install the new roll of paper with the end of the paper at the top of the roll.

4. Assemble the cover onto the printer with the leading edge of the paper over the roller.

Leading Edge of

Paper Over Roller

579425 REV A

Tab

Figure 11

Page 34

Maintenance

Install a Printer

1. Turn OFF the machine and disconnect it from its power

source.

2. Remove the oil drain bottle.

3. Remove the screws holding the shroud. See Figure 7.

4. Hang the shroud on the back of the machine as shown in Figure 8.

5. Remove the two screws on the top corners of the control panel, allowing the control panel to swivel forward.

6. Remove the cap from the printer location cutout by pressing on the cap’s tabs from the back of the control panel and pushing the cap out of the panel.

7. Remove the two locking arms from the printer by inserting the face of a athead screwdriver under each tab near the back of its locking arm. Pry the tab outward while sliding the entire arm away from the printer.

Figure 12

8. Place the printer into the cut-out area on the control panel. Press the face of the printer ush to the panel, oriented with the paper coming out at the top of the printer as shown in Figure 11.

9. Replace the printer locking arms from within the inside of the control panel. Push them forward until they come into rm contact with the inside face of the control panel.

10. Using the harness included with the printer, connect to the control board as shown in Figure 12. The wires are marked with their respective connector labels.

11. Attach the two free connectors to the appropriate connectors on the back of the printer.

12. Swivel the control panel back into place and fasten it using the two screws removed in Step 5.

13. Assemble the shroud back onto the machine and install the screws removed in Step 3.

14. Reinstall the oil drain bottle.

The printer is now ready for use.

579425 REV A

Page 35

Replace the Oxygen Sensor in the

Refrigerant Identier

Maintenance

The refrigerant identier in the machine contains a replaceable oxygen sensor that can affect the way the machine works if the sensor is not functioning correctly.

• If the machine displays the following message, immediately replace the oxygen sensor:

OPERATING TIME OF THE IDENTIFIER AND UNIT ARE

LIMITED

REPLACE ID O2 SENSOR SOON

UNIT WILL BECOME NONFUNCTIONAL

• If the machine displays the following message, the oxygen sensor has expired. Neither the identier nor the machine is able to recover or add refrigerant to the internal tank.

ANALYZER ERROR 6

O2 SENSOR FAILURE

SENSOR MUST BE REPLACED

UNIT WILL NOT RECOVER OR ALLOW TANK FILL

SEE MANUAL

Replacement Procedure

1. Disconnect the machine from its power source.

2. Remove the oil bottle, and remove the four screws holding the shroud. See Figure 13. Hang the shroud on the back of the machine.

Remove four screws holding shroud.

Figure 13

3. Disconnect the wire harness, USB connector, and sample hose from the identier. See Figure 14.

4. Remove the two screws holding the identier to the machine, and remove the identier.

5. Carefully pry the oxygen sensor cap from the housing. Gently pull on the cap and wires until the connector exits the housing.

CAUTION: The wire connected to the cap is connected

internally to the identier. To prevent equipment damage,

do NOT pull on this wire.

579425 REV A

Disconnect wire harness,

USB connector,

and sample hose

Oxygen

Sensor

Cap

Figure 14

Page 36

Maintenance

6. Disconnect the wire harness at the connector by pressing on the center tab. Pull the connectors apart. See Figure 15.

7. Move the cap and harness aside. Hold the lead from the sensor, and use a at-blade screwdriver to unthread and remove the oxygen sensor. See Figure 16.

8. Remove the pink protective lm from the threaded end of the new oxygen sensor.

9. Install the new oxygen sensor, using the screwdriver to thread it into place. Tighten the sensor to 4 in. lb.

10. Reconnect the lead at the connector, and tuck the wires into the opening.

11. Replace the cap and push until it “clicks” into place. Install the identier onto the machine, and reconnect the wire harness, USB connector, and sample hose.

12. Verify the wiring is not binding, and replace the shroud.

Press to disconnect wire harness

Use at-blade

screwdriver to remove sensor.

Figure 15

Refrigerant Identier

The refrigerant identier samples refrigerant going into the ISV to verify that it is R1234yf and not contaminated. Replace the sample hose assembly during every lter change and also if prompted by an error message saying that the hose is clogged. See Figure 17.

1. Disconnect the existing sample hose assembly between the solenoid and the refrigerant identier, and install a new sample hose assembly.

Note: If the lter is any color but white, the lter needs to

be replaced also.

2. Pull th lter out of the brackets while removing the barbs from the rubber connectors.

3. Install a new lter with the arrow pointing upward as shown. Push the lter barbs into the rubber connectors.

4. Install the shroud on the machine and swith the power ON.

Figure 16

Barb

Refrigerant Identier

Sample Hose

Assembly

Install new lter with

arrow shown.

positioned as

↑

Figure 17

Replace the sample hose assembly during

every lter change.

579425 REV A

Page 37

Replace Service Hoses and/or Service Couplers

Ensure pressure has been removed from service hoses before disconnecting a hose or coupler from the machine. Pressure gauges must read at or below 0 psig.

If pressure exists, recover the refrigerant from the hoses before disconnecting a hose or coupler.

1. The machine performs a 30 second vacuum to ensure

hoses are empty.

2. The machine displays

Disconnect old hoses and replace with new hoses Press OK to continue

Press ESC to exit

Remove and replace old service hoses. Press OK.

Maintenance

3. The unit directs the user to connect hoses to the storage

ports and press OK to begin unit conditioning.

4. A vacuum is performed on the unit until excess air has

been removed from the service hoses.

5. The machine is now ready to use.

Tank Fill Hose Filter Service

The tank ll hose at the rear of the machine (see Figure 18) contains a lter that can be cleaned when it appears that refrigerant ow is restricted.

When the machine senses low ow, it can display one of the following messages:

• SOURCE TANK EMPTY, but the source tank is known

to contain refrigerant, connections are secure, and the source tank valve is open.

• REPLACE IDENTIFIER FILTER, but the refrigerant

identier lter is known to be unrestricted, the source tank contains refrigerant, connections are secure, and the source tank valve is open.

The tank ll hose lter might be plugged.

579425 REV A

Tank Fill

Hose

Figure 18

Page 38

Maintenance

Cleaning the Tank Fill Hose Filter

1. First ensure that pressure does not exist in the line. Disconnect the external source tank, and perform a manual tank ll to capture any refrigerant in the line.

2. Disassemble the tank ll hose at the lter housing as shown in Figure 19.

3. Remove the lter. The recommended method to remove debris from the lter is by using air pressure.

Note: If a solvent is used, allow adequate drying time before reassembly.

4. After the lter has been installed back into the lter housing, torque the housing assembly to 8.5 N•m (6 ft. lb.).

Disassemble the

Filter Housing

Figure 19

579425 REV A

Page 39

A/C Service Function

Replacement Parts

Contact Robinair Customer Service (1-800-533-6127) for more information regarding the replacement parts listed here.

Component

Calibration Weight 16214 Filter 34724 Oil Drain Bottle 19100

Printer 30038

Printer Paper (3 rolls) 34214 LP Service Coupler 18122 HP Service Coupler 18123 Service Coupler Set

(high-side [red] and low-side [blue] couplers) Hose Set without Couplers

(high-side [red] and low-side [blue]) Service Hose without Coupler (low-side, blue) 70123 Service Hose without Coupler (high-side, red) 70124 Vacuum Pump Oil (pint) 13119 Vacuum Pump Oil (quart) 13203 Vacuum Pump Oil (gallon) 13204 Vinyl Dust Cover (optional) 17499 Identier Filter 16913 Identier Oxygen Filter 16916 Identier Sample Hose 16106 Tank Fill Hose Filter 10233

Replacement

Part No.

18124

71234

WARNING: To prevent personal injury, use only those repair parts called out in this parts list. Items found in this parts list have been carefully tested and selected by Robinair.

Glossary

A/C System : The vehicle air conditioning system being serviced. Evacuation : Moisture and other non-condensables are removed from an A/C system by a vacuum pump. Internal Storage Vessel (ISV) : The rellable refrigerant storage tank designed specically for this machine;

9.5 kg (20.94 lb) capacity. Leak Test (Vacuum) : Components containing refrigerant are evacuated and monitored for pressure rise,

which could indicate a leak.

Machine : Model No. AC1234-4. Leak Check : Components containing refrigerant are pressurized and monitored for pressure decay, which

could indicate a leak.

Recovery / Recycling : Refrigerant is recovered from an A/C system, ltered, and stored in the ISV. Refrigerant : R1234yf.

579425 REV A

Page 40

Troubleshooting Messages

Display Cause Solution

CALIBRATION CHECK

FAILED

CHARGE STALLED!

DATABASE NOT AVAILABLE

EXCESS TANK WEIGHT

FILTER CAPACITY

EXHAUSTED, FILTER MUST

BE REPLACED

FILTER WEIGHT XXX.XYY

REPLACE FILTER NOW?

Internal scale is out of calibration.

Refrigerant is stalled in the ISV or the machine.

Machine is not shipped with database installed.

Overll safety circuit tripped. Machine is locked out because of too much refrigerant in ISV.

150 kg (330 lb) or more refrigerant has been recovered since last lter change.

Select If calibration continues to fail, exit current test and contact a Robinair authorized service center for repair.

Verify connections are secure, valves are in correct position, and ISV contains enough refrigerant to complete charge.

Contact a Robinair authorized service center for more information.

Refer to Filter Maintenance

section of this manual for

instructions to change lter.

to retry calibration check.

FILTER SERIAL NUMBER

HAS ALREADY BEEN USED.

RE-ENTER OR EXIT?

HIGH TANK PRESSURE

INSUFFICIENT

REFRIGERANT.

6.00 KG REQUIRED FOR SYSTEM FLUSH

INSUFFICIENT

REFRIGERANT

AVAILABLE FOR CHARGE

SELECTED: XX.XXYY AVAILABLE: XX.XXYY

Filter serial number entered into the machine is not correct.

Machine is locked out because pressure in ISV is too high, possibly because of excessively high tank temperature.

Not enough refrigerant in the ISV to perform a system ush.

After a desired weight is entered, if the charge process will leave less than 0.67 kg (1.4 lb) of refrigerant in ISV, the charge function will not start.

Filter has already been used on

this machine. Obtain new Robinair

lter No. 34724.

Allow machine to cool before performing additional A/C service. If problem continues, contact a Robinair authorized service center for more information.

Refer to Tank Fill in Maintenance

section of this manual.

Refer to Tank Fill in the

Maintenance section of this manual.

579425 REV A

Page 41

Troubleshooting Messages

Display Cause Solution

INVALID CODE

INVALID SERIAL NUMBER!

NO PRESSURE ON INLETS

CHECK CONNECTIONS

RECOVER ANYWAY?

OIL DRAIN HALTED.

PRESSURE ERROR,

RETRY OR EXIT?

Activation code entered into the machine is not correct.

Filter serial number entered into the machine is not correct.

System pressure is below 0.35 bar gauge.

Accumulator pressure failed to rise above 1.10 bar within the minute before an oil drain was supposed to occur.

Verify activation code is entered exactly as received. Capitalization is required.

Verify serial number entered

matches serial number on lter. Verify lter has not been used on

machine previously.

Verify high-side (red) and low-side

(blue) hoses are connected and

coupler valves open. Select

to RECOVER; select bypass recover and proceed to VACUUM.

Adequate pressure is required within the accumulator to force the oil, which has been separated from the refrigerant, out of the system. Select

to exit.

to retry; select

OIL DRAIN HALTED.

FLOW ERROR,

RETRY OR EXIT?

OIL LIFE REMAINING

XX:XXX

CHANGE OIL NOW?

OUT OF RANGE

ACCUMULATOR PRESSURE

OUT OF RANGE

ISV PRESSURE

OUT OF RANGE

ISV TEMPERATURE

Accumulator pressure failed to drop below 0.62 bar, indicating all oil failed to drain within the time given for oil drain.

Display shows vacuum pump oil life remaining until machine locks down.

Accumulator pressure transducer is not reading pressure correctly.

Internal storage vessel

pressure transducer is not

reading pressure correctly.

Internal storage vessel

temperature sensor is not

reading temperature correctly.

Unit may need time to drain all the oil back due to low temperature, thick oil viscosity, or large oil quantity Select select to escape.

Refer to Maintenance section of this manual for instructions to change vacuum pump oil.

Exit current test and contact a Robinair authorized service center for more information.

to retry, or

579425 REV A

Page 42

Troubleshooting Messages

Display Cause Solution

OUT OF RANGE

LS PRESSURE SENSOR

POWER BOARD

COMMUNICATION FAILED

PRESSURE LEAK TEST

FAILED

CHECK UNIT FOR LEAKS

PURITY TEST FAILED

SOURCE TANK IS EMPTY

Low-side pressure transducer is not reading pressure correctly.

Failed communication with relay board.

A leak in vehicle A/C system.

Refrigerant tested is not R1234yf or it is contaminated.

Refrigerant cannot be transferred to the ISV because the source tank is empty.

Exit current test and contact a Robinair authorized service center for more information.

Cycle power. If problem continues, contact a Robinair authorized service center for more information.

Exit current test and perform repairs on vehicle A/C system.

Do not recover contaminated refrigerant into the machine; use an external refrigerant recovery machine dedicated to contaminated refrigerant. See "Recover Refrigerant from a Vehicle" on p. 17.

Exit current test and replace the source tank.

TANK FULL. REMOVE

REFRIGERANT BEFORE

CONTINUING

TRIAL PERIOD EXPIRED

UNIT ACTIVATION

REQUIRED TO CONTINUE

USE

VACUUM TEST FAILED.

CHECK SYSTEM FOR LEAKS

PRESS CONTINUE TO HOSE

EQUALIZE

PRESS ABORT TO HOSE

COMPENSATE

ISV is too full to recover additional refrigerant.

Failure to register and activate the machine within 30 days of initial startup will cause the machine to lock out and no longer function.

A leak in vehicle A/C system.

Choose method to complete Charge service.

Perform a charge process to remove refrigerant from ISV before any further recovery attempts.

Select

Activation section in this manual to register the machine.

Exit current test and perform repairs on vehicle A/C system.

Choose F3 key to complete

service by Hose equalize. Vehicle needs to be turned ON to complete the procedure.

Otherwise choose F3 to complete

by compensation.

and refer to Unit

579425 REV A

Page 43

Troubleshooting Messages

Display Cause Solution

CLOGGED FILTER

INSUFFICIENT VACUUM FOR

SETUP

FILTER CAPACITY LOW

O2 SENSOR ON THE

IDENTIFIER WILL HAVE TO

BE REPLACED SOON

VACUUM LEAK TEST FAILED

PRESSURE LEAK TEST

FAILED

REFRIGERANT IDENTIFIER

ERROR

Debris in the Flush Filter may be restricting ow.

Leak found in the A/C system. Contact service center.

Warning message to prepare user for lter replacement.

Warning message to replace O2 sensor on the identier.

Leak found in the vehicle A/C unit.

Problem with the connection to the identier.

Follow screen instructions.

Recover refrigerant and replace

lter.

Filter will lock-out soon. Replace lters. See screen information to

order parts.

System will be locked-out once

the sensor goes bad. Contact service center to replace O2 sensor.

Exit current test and perform repairs on the A/C system.

Follow screen instructions.

Contact service center if issue persists.

PRINTER OUT OF PAPER Empty printer paper.

USED OIL BOTTLE FULL

AIR FLOW ERROR

REAL-TIME CLOCK FAILURE System clock is incorrect.

VACUUM HALTED. INLET

PRESSURE IS TOO HIGH.

Used oil bottle is lled completely.

Not enough air ow inside the equipment.

Vacuum cannot be performed with high inlet pressure.

Replace printer paper and continue.

Empty bottle to avoid overow of

oil.

Check for obstruction. Machine is not safe to operate. Contact service center.

Contact service center. The time on the machine is incorrect. Data stored and printed on the machine is inaccurate.

Check for pressure. Perform recovery.

579425 REV A

Page 44

Troubleshooting Procedures

Setup, Tank Fill, and Background Tank Fill Functions

Display Message: Purity Test Failed

During SETUP, TANK FILL, or BACKGROUND TANK FILL, if the machine displays

purity test failed recover contaminated refrigerant from system and hoses. ok to Retry esc to quit

the refrigerant in the source tank is either not R-1234yf or it is contaminated. In either case, it should not be added to the internal storage vessel (ISV) in the machine. The contaminated refrigerant sampled by the refrigerant identier in the machine must be removed.

A refrigerant recovery machine (Robinair

25700) dedicated to contaminated refrigerant is required for the following steps. Refer to Figure 20.

1. Connect the tank ll hose adapter (provided in the Accessory Kit) to the low-side coupler of the 25700 refrigerant recovery machine.

2. Connect the other end of the adapter to the tank ll hose tting on the machine.

3. Connect the discharge hose from the to a tank specied to receive contaminated refrigerant.

4. Start the 25700 and open the coupler valve. Run a recovery until the gauge on the 25700 indicates vacuum.

5. Shut off the 25700.

6. Slowly and carefully disconnect the adapter from the tank ll hose and the 25700. There might still be a small amount of pressure in the line.

Robinair 25700

Refrigerant Recovery Machine

Tank Fill Hose

Adapter

No. 17990

Contaminated

Refrigerant Tank

Figure 20

579425 REV A

Page 45

Troubleshooting Procedures

Recovery Function or Automatic Function

Display Message: Purity Test Failed

During the RECOVERY function or AUTOMATIC RECOVERY function, if the machine displays

purity test failed recover contaminated refrigerant from system and hoses. ok to Retry esc to quit

the refrigerant in the source tank or in the vehicle A/C system is either contaminated or it is not R-1234yf. In either case, it should not be added to the internal storage vessel in the machine.

The contaminated refrigerant sampled by the refrigerant identier in the machine must be removed.

A refrigerant recovery machine (Robinair 25700) dedicated to contaminated refrigerant is required for the following steps:

Connect Robinair 25700

contaminated refrigerant

recovery machine here.

Figure 21

1. With the machine still connected to the vehicle and the couplers open, connect the low-side (blue) coupler from the 25700 to the contaminant recovery port on the back of the machine. See Figure 21. Open the coupler valves.

2. Connect the discharge hose from the 25700 to a tank designed to receive contaminated refrigerant.

3. Start the 25700 and run a recovery according to instructions supplied with the machine.

4. Upon achieving a vacuum in the vehicle (or per recovery machine instructions), disconnect the 25700 from the machine.

5. Clear the vehicle of residual contamination according to the vehicle manufacturer’s instructions before continuing service.

579425 REV A

Page 46

Storage and Transportation of Equipment

Storage

Never leave the machine live if an immediate use is not scheduled.

1. Disconnect the machine from its power supply.

2. Loop the service hoses around the handle twice and attach them to the storage ports. See Figure 22.

3. Store the machine in a dry, stable area, away from ames and hot surfaces. The temperature of the storage area should range between -18°C and 60°C (0°F and 140°F).

4. Lock the front wheels.

Transportation of Equipment

WARNING: To prevent personal injury, should the machine require transport to a Robinair service center, follow local government regulations regarding transportation of equipment containing R1234yf.

Figure 22

Hose couplers connected to storage ports.

579425 REV A

Page 47

Disposal of Equipment

At the end of its useful life, dispose of the R1234yf machine according to current government regulations.

• Public administration and producers of electrical / electronic equipment (EEE) are involved in facilitating the processes of the re-use and recovery of waste electrical / electronic equipment through the organization of collection activities and the use of appropriate planning arrangements.

• Do not dispose of this equipment as miscellaneous solid municipal waste. Arrange to have it collected separately. Unauthorized disposal of waste electrical / electronic equipment is punishable by law with appropriate penalties.

• The reuse and correct recycling of electrical / electronic equipment (EEE) is required for the protection of the environment and the well-being of humans.

Disposal of Recycled Materials

It is the responsibility of the user to determine if a material is a hazardous waste at the time of disposal. The user must ensure compliance with all applicable laws and regulations.

1. Deliver the refrigerant recovered from A/C systems to gas suppliers for recycling or disposal.

2. Deliver the lubricants extracted from A/C systems to used oil collection centers.

3. Review the laws in your jurisdiction to determine correct disposal procedures for pump oil.

Disposal of the Machine

1. Detach and vent the gas from the machine circuit. Completely discharge the refrigerant tank in compliance with current government regulations.

2. Deliver the machine to an appropriate disposal center.

Disposal of Batteries

At the end of their useful life, dispose of batteries according to current government regulations. Batteries must be recycled or disposed of correctly. Do not throw away batteries as part of normal refuse disposal.

WARNING: To prevent personal injury, do not throw batteries into open ame.

CAUTION: R1234yf systems have special ttings (per SAE specications) to avoid cross-contamination. Do not adapt your unit to a different refrigerant system, as failure will result.

579425 REV A

Page 48

Software License Notices

BOSCH AUTOMOTIVE SERVICE SOLUTIONS SOFTWARE LICENSE NOTICES

Bosch Automotive Service Solutions 28635 Mound Road Warren MI 48092 USA

Phone numbers USA 800-533-6127 EMEA +49 (0) 6182 959-225

This Bosch Automotive Service Solutions software is released under the software license agreement presented at product activation. All other products or service names are the property of their respective owners. Registered trademarks of their respective companies and are hereby acknowledged. The following notices pertain to this Bosch Automotive Service Solutions software license:

1. This product contains IAR Standard libraries. IAR software license agreement is reported below and located at http://www.iar.com/Global/Products/Software_licenses/SLA_February_2013.pdf.

IAR standard library includes third party software as declared in the third party licenses document reported below and located at

http://www.iar.com/Global/Products/Software_licenses/3rdpartyLicenses.html

2. This product contains LibTomCrypt is a fairly comprehensive, modular and portable cryptographic toolkit that provides developers with a vast array of well known published block ciphers, one-way hash functions, chaining modes, pseudo-random number generators, public key cryptography and a plethora of other routines. http://www.libtom.org. LibTomCrypt is public domain. As should all quality software be. Tom St Denis

3. This product contains Freescale software as part of the Freescale microcontroller BSP. Refer to the Freescale Semiconductor License Agreements for the use terms below reported and located at

https://www.freescale.com/webapp/sps/download/license.jsp?colCode=DL-MQX-CX&prodCod e=MQX&appType=file2&location=null&DOWNLOAD_ID=null&fsrch=1&sr=1&pageNum=1&Parent_ nodeId=&Parent_pageType

579425 REV A

Page 49

IAR Software License Agreement

Concerning the Products: IAR Embedded Workbench® and visualSTATE® from IAR Systems AB

PREAMBLE

THIS SOFTWARE LICENSE AGREEMENT (“THE AGREEMENT”) APPLIES TO PRODUCTS LICENSED BY IAR SYSTEMS AB INCLUDING ANY OF ITS SUBSIDIARIES (“IAR SYSTEMS”) OR DISTRIBUTORS (“IAR DISTRIBUTORS”), TO YOU (“THE LICENSEE”).

The order confirmation from IAR Systems, or when applicable the agreement between IAR Systems and the Licensee, will set out, apart from the applicable licensed product and license fee (which will also be stated in the Invoice), a) if the License in question is a PC-locked License or a Multi-user License, b) in case of a Multi-user License with the allowed number of simultaneous users, c) if the license includes a time limited Support and Update Service and in such cases the expiry date of such service. Any opening of a package where these terms have been stated or referred to, and any use of IAR Systems software, is subject to these terms and conditions.

YOU AS A USER OF THE LICENSED PRODUCTS STATED ABOVE AND ON THE INVOICE, WILL BIND THE CORPORATION OR ORGANIZATION ALSO SET OUT ON THE INVOICE TO THIS AGREEMENT, BY OPENING OF A PACKAGE OR INSTALLING SOFTWARE WHERE THIS AGREEMENT HAS BEEN STATED OR REFERRED TO. IF YOU ARE NOT IN AGREEMENT WITH THE TERMS HEREIN, OR DO NOT HAVE THE AUTHORITY TO BIND YOUR CORPORATION OR ORGANIZATION TO THESE TERMS, YOU SHALL IMMEDIATELY CONTACT IAR SYSTEMS AND YOU MAY NOT INSTALL ANY SOFTWARE OR MAKE USE OF ANY PARTS OF THE PRODUCT.

1. DEFINITIONS

The following terms have the meanings set forth below whenever they are used in this Agreement:

1.1 “Executable Software” means a copy of the executable code version of the software program(s) included in the enclosed package or otherwise specified in this Agreement or Invoice (including any link-time and runtime modules), along with templates and other instructions and any Software updates, revisions, and additional modules and templates (if any) that the Licensee may receive from IAR Systems hereunder from time to time.

1.2 “Software Source Code” has the meaning set out in section 3.7.

1.3 “Software” is a collective term for Executable Software and Software Source Code as defined above.

1.4 “Documentation” means a copy of the documentation, as provided by IAR Systems together with the Software for use by the Licensee.

1.5 “Product” means the Software and Documentation licensed to the Licensee under the conditions of this Agreement.

1.6 “Invoice” means IAR Systems’ or IAR Distributor’s invoice to the Licensee for the Product license granted hereunder.

1.7 “PC-locked License” has the meaning set out in section 3.2.

1.8 “Mobile License” has the meaning set out in section 3.3.

1.9 “Multi-user License” has the meanings set out in section 3.4.

1.10 “Network License” has the meanings set out in section 3.5.

1.11 “Global Network License” has the meanings set out in section 3.6.

1.12 “Concurrent Users” has the meaning as set out in section 3.7.

1.13 “Commuter license” has the meaning as set out in section 3.8.

1.14 “Evaluation License” has the meanings set out in section 3.12.

1.15 “Site” means the physical premises of the Licensee within the borders of one city.

1.16 “Target Architecture” means the family or group of embedded micro-controller and micro-processor devices belonging to one processor architecture, as defined by its instruction set, and as specified on the Invoice.

1.17 “Support and Update Services” means the services set out in section 12.

2. TERM OF AGREEMENT

2.1 This Agreement shall become effective on the latest at the Licensee’s receipt of the Software and shall remain in effect for an indefinite period in time, subject to the terms and conditions set out below – in particular the right of IAR Systems to terminate the Agreement upon Licensee’s breach. Registration of the Licensee as a rightful user of Licensed Products shall be made in accordance with applicable instructions from IAR Systems.

2.2 For the avoidance of doubt: Also for Software delivered with a temporary license key (for some products called quick start key) enabling use for a limited time, the Agreement terms have become effective, including but not limited to its payment terms and use restrictions, already upon the Licensee’s receipt of the Software, regardless of whether registration is made or not. (Evaluation licenses without obligation to pay license fees, are available to the extent separately provided by IAR Systems.)

3. OWNERSHIP AND LICENSE GRANT

3.1 IAR Systems holds the copyright, trade secrets, and any other intellectual property rights which subsist in the Licensed Product and all copies thereof. No title or other rights in the Licensed Product (other than rights expressly granted herein) shall pass to the Licensee.

THE PRODUCT IS LICENSED, NOT SOLD, TO THE LICENSEE FOR USE ONLY UNDER THE TERMS OF THIS AGREEMENT. THE LICENSEE ACKNOWLEDGES THAT THE PRODUCT CONSISTS OF PROPRIETARY, UNPUBLISHED PRODUCTS OF IAR SYSTEMS, PROTECTED UNDER INTERNATIONAL COPYRIGHT AND TRADE SECRET LAWS.

579425 REV A

Page 50

IAR Software License Agreement

3.2 PC-locked License: To the extent the relevant license granted is a PC-locked License, the terms in 3.2.a

and 3.2.b shall apply. A PC-locked License is a single-user license, locked to the computer where the software is installed.

3.2.a Subject to the terms and conditions of this Agreement, IAR Systems hereby grants to the Licensee a

personal, non-transferable and non-exclusive PC-locked License to use the Software. The Licensee’s number of authorized users of the Software under the PC-locked License, if more than one, is stated in the Invoice or otherwise in writing from IAR Systems.

3.2.b The PC-locked License may be used by the Licensee only on one single, self-contained computer unit

(stationary or portable), designated through its IP number or other means of identification. A switch of the designated computer to another single computer may be allowed to transfer the license via a transfer program provided by IAR Systems within the license management system. The Software may not be accessed by users from other computer units than the unit designated as set forth in this clause; through modem, Internet or any other means of network or remote access.

3.3 Mobile License: To the extent the relevant license granted is a Mobile License, the terms in 3.3.a and 3.3.b

shall apply. A Mobile License comes with a hardware lock (dongle). A hardware lock is a device to be attached to one of the computer’s external ports, which allows the Licensee to move the license to another computer. A hardware lock is part of the product package only to the extent explicitly ordered.

3.3.a Subject to the terms and conditions of this Agreement, IAR Systems hereby grants to the Licensee a

personal, non-transferable and non-exclusive Mobile License to use the Software. The Licensee’s number of authorized users of the Software under the Mobile License, if more than one, is stated in the Invoice or otherwise in writing from IAR Systems.

3.3.b The Mobile License may be used by the Licensee only for one single user, but with the right to a switch of

the designated computer to another single computer using a hardware lock. The Software may not be accessed by users from other computer units than the unit designated as set forth in this clause; through modem, Internet or any other means of network or remote access.

3.4 Multi-user License: To the extent the Product license granted is a Multi-user License, the terms in this 3.4

shall apply. Subject to the terms and conditions of this Agreement, IAR Systems hereby grants to the Licensee a personal, non-transferable and non-exclusive Multi-user License to use the Software. The Licensee’s number of authorized users of the Software under the Multi-user License, if more than one, is stated in the Invoice or otherwise in writing from IAR Systems or IAR Distributors.

3.5 A Network License is a Multi-user License, located on a single designated license server and used by multiple

users on a network and on one Site only. The Network License is locked either to the computer where the license server software runs, or to a hardware lock (dongle). The use of a hardware lock allows to move the Network License to another server computer, in case of server failure. The Network License can be used on all client computers on the network where the Software is installed. However, the Network License is made for a maximum number of concurrent users.

3.6 A Global Network License is a Multi-user License, located on a license server and used by multiple users on

a network that can be accessed from multiple Sites globally. The Global Network License is locked either to the computer where the license server software runs, or to a hardware lock (dongle). The use of a hardware lock allows to move the Global Network License to another server computer, in case of server failure. The Global Network License can be used on all client computers on the network where the Software is installed. However, the Global Network License is made for a maximum number of concurrent users.

3.7 Concurrent Users: For Products that are Executable Software and licensed as Network Licenses, the

definition of concurrency is given by the license server software, which also keeps track of the number of current of users. A user session of an Executable Software is always a minimum of thirty (30) minutes, and is deemed to last for additional thirty (30) minutes after the last license activation by the license server. For Products including Software Source Code, the software shall be deemed in (concurrent) use on a computer when it is loaded into temporary memory (i.e. RAM) or installed into permanent memory (e.g., hard disk, CDROM, or other storage device) of that computer.

3.8 Commuter licensing: For Products released 2012 and later including a new license management system

(LMS) a commuter license is granted. Commuter licensing permits a temporary use of a network license on a personal computer not connected to the network for up to 15 days. The commuter license permits the use of the Product outside the designated Site.

3.9 Source Code License: If the Product Licensee receives hereunder contained software modules or components

in source code format (“Software Source Code”), the following shall apply to such Software Source Code, in addition to all other provisions of this Agreement: The Licensee may use such Software Source Code only in conjunction with the Product and the Software Source Code or any derivative works thereof. The Software Source Code may only be compiled and linked with products

579425 REV A

Page 51

IAR Software License Agreement

from IAR Systems, and only in accordance with the provisions on such use set out in the Documentation and/ or this Agreement. The Licensee is strictly prohibited to make any other use of the Software Source Code. Any breach of this Section 3.9 shall be considered a material breach of this Agreement.

THE LICENSEE ACKNOWLEDGES THAT THE SOFTWARE SOURCE CODE EMBEDS COPYRIGHTED AND PROPRIETY INFORMATION OF IAR SYSTEMS, AND THAT MAKING SOFTWARE SOURCE CODE ACCESSIBLE TO OTHERS OUTSIDE THE SCOPE OF THIS AGREEMENT, BY THE NATURE OF SOURCE CODE, SEVERELY DAMAGES THE INTELLECTUAL PROPERTY RIGHTS OF IAR SYSTEMS, AND AGREES TO COMPENSATE IAR FOR ALL DAMAGE RESULTING FROM SUCH BREACH, THAT CAN BE REASONABLY SUBSTANTIATED BY IAR. The Licensee shall keep and protect the Software Source Code with at least the same degree of care as its own proprietary source code, as further specified in section 5.

3.10 If the Product the Licensee receives hereunder contains Third Party-Owned software, the use of such Third Party-Owned software may be restricted to a specific Target Architecture. See Section 11.2 below.

3.11 Back-up Copies: The Licensee may make back-up copies of the Software in machine executable code form, only to be used in the event and to the extent that the copy of the Software received from IAR Systems fails to function, is lost, damaged, or destroyed. The Licensee warrants that it will make no other copies of the Software and will not allow, authorize, or assist others to copy any part or all of the Software in any form without the prior written approval of IAR Systems. There may be no more copies than are necessary to form part of a reasonable back-up cycle for the Licensee. Back-up copies of the Software may be kept by the Licensee in a bank deposit or other such secure place as is normally used by the Licensee for storage of its computer program back-ups. The rights for the Licensee under this section shall not in any case include any measures to affect or decrease the function of the software protection included in the software.

3.12 An Evaluation License is solely intended for testing and evaluation purposes. Any other use than for testing and evaluation is prohibited. IAR Systems has no obligation to provide support or related services and no warranties. IN NO EVENT SHALL IAR SYSTEMS BE LIABLE TO THE OTHER FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL, PUNITIVE OR TORT DAMAGES OF ANY NATURE OR KIND WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOST PROFITS, IN CONNECTION WITH OR ARISING OUT OF THE USE OR PERFORMANCE OF SOFTWARE, SUPPORT MATERIALS, OR THE PROVISION OF SERVICES, EVEN IF THE OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Section 11 in this Software License Agreement may also apply to an Evaluation License.

4. LICENSE RESTRICTIONS

4.1 The Licensee may not remove, make emulation, reverse engineer, decompile, or disassemble the Executable Software. Licensee is not allowed to derive the source or assembly code of files provided in executable or object formats. The Licensee accepts that all information gained about the Software is the valuable intellectual property of IAR Systems and as such must be treated as confidential as described under Article 5. The Licensee warrants that it will not sell, license, lease, rent, loan, lend, transmit, network, communicate, or otherwise distribute or transfer the Software in any manner to any third party whether on a permanent or temporary basis, except as explicitly stated in this Agreement. Furthermore the Licensee warrants that it will not use or permit the use of (including without limitation by time sharing or network use) the Software for the benefit of any entity other than the Licensee; or in a computer service business; make unauthorized copies of the documentation; make verbal or media translations of the documentation; make telecommunications data transmissions of the Software; use long-haul gateways on any central processing unit on which the Software is used. The Licensee is also expressly prohibited from adapting, modifying, revising, improving, upgrading, enhancing, and creating derivative works of the Executable Software for any purpose including error correction or any other type of maintenance.

4.2 The Licensee shall keep records of the Licensee’s use of Software. The Licensee shall make the records available to either IAR Systems or a neutral third party on reasonable notice, as agreed between the parties. In the case of a neutral third party audit, IAR Systems and Licensee shall in good faith mutually appoint an auditor. Should such an agreement not be reached within 60 days after IAR Systems notice, then the parties agree to have Business Software Alliance conduct such an audit, or itself elect an auditor. The Licensee will permit IAR Systems or a third party, as the case may be, to have access to the Licensee’s records and computer systems and to use software audit tools on the Licensee’s systems to ensure that the Licensee is using its software in accordance with the applicable license terms. Upon the Licensee’s request, the party conducting the audit with the Licensee shall enter into a non-disclosure agreement with the Licensee, to protect the Licensee’s propriety and/or confidential information. Information retrieved and/or conveyed to IAR Systems as a result of such an audit as here described shall be limited as to only ensure that the Licensee is using its software in accordance with the applicable license terms, or evidence of the contrary.

4.3 Subject to the other terms herein, and with the Licensee as fully responsible for all actions or omissions of such a consultant, Licensee may let a consultant use the Software for work solely on behalf of the Licensee for the licensed purpose and provided that the Software is not used for any other purpose or third party.

4.4 Upon each and every breach by the Licensee hereunder a contractual penalty amounting to 200% for breach

579425 REV A

Page 52

IAR Software License Agreement

under sections 3.2, 3.3, 3.4, 3.5, 3.6, 3.11, 4.1 or 4.3 and 1000% for breach under section 3.8 of the applicable licensee fee under the relevant Invoice is payable by the Licensee to IAR Systems. In case IAR Systems’ actual damage due to the breach would exceed this amount, also the remainder shall be paid by the Licensee, see also Section 3.8.

5. CONFIDENTIALITY

5.1 The Licensee agrees that all material and information relating to the Software is made available for the

use solely under and in accordance with this Agreement. The Licensee has no right at any time during or after cancellation or termination of this Agreement to disclose such material and/or information relating to the Software, whether directly or indirectly, to any third party without IAR Systems’ prior written approval. The Licensee shall hold harmless, defend, and indemnify IAR Systems from and against any and all losses, costs, damages, and expenses arising out of or in connection with the Licensee’s failure to comply with requirements of this Article 5. The Licensee’s confidentiality obligations hereunder shall survive cancellation or termination, for any reason, of this Agreement.

6. PAYMENT TERMS AND CONDITIONS

6.1 In consideration of the rights granted and services rendered by IAR Systems under this Agreement, the

Licensee shall pay the license fees for the Software as specified in the Invoice. Payments are to be made according to the payment schedule stated in the Invoice, or if not stated, invoices are payable within 30 days of the invoice date.

6.2 If the Licensee fails to effect payment within the stipulated time, IAR Systems or IAR Distributors shall be

entitled to a) charge interest after due date as stated in the Invoice, or if not stated in the invoice, the interest charged will be the reference rate set by Sweden’s central bank (the Riksbank) + 8%. b) postpone the fulfilment of any of its own obligations until payment is made, and/or c) terminate the Agreement by notice in writing to the Licensee and recover from the Licensee any and all loss incurred.

6.3 All prices are exclusive of, and the Licensee is responsible for, all fees and taxes, including custom duties,

importation fees, sales, use, withholding, gross revenue, and like taxes, dues, and charges assessed or incurred in connection with the provision of goods and services under this Agreement.

7. LIMITED WARRANTY

7.1 IAR Systems warrants that the media on which the Software is recorded upon receipt by the Licensee will

be free from defects in materials and faulty workmanship under normal use for a period of ninety (90) days from the date of delivery to the Licensee. During this warranty period IAR Systems will, at its option, after its receipt of the media in return, repair or replace, free of charge, defective media upon which the Software was supplied and record a copy of the Software on the repaired or replacement media. Said repair or replacement shall be the Licensee’s exclusive remedy under this media warranty. Notwithstanding the foregoing, IAR Systems shall have no responsibility to repair or replace a media which, in IAR Systems’ opinion, has been damaged by the Licensee by accident, abuse, or as a result of attempted self-maintenance service.

7.2 IAR Systems does not warrant that the Software will meet the Licensee’s requirements or that the operation

of the Software will be uninterrupted and error free. The Licensee is solely responsible for the selection of the Software to achieve its intended results or for the results actually obtained.

7.3 The above warranty does not apply to conditions resulting from improper use, external causes, including

service or modifications not performed by IAR Systems or a contractor appointed by IAR Systems, or operation outside the specified environmental parameters. IAR Systems will not be responsible for operation of the Software other than on the host equipment specified in the Invoice and in conjunction with the operating environment designated for each version of the Software. Minor deviations from the above warranty, which are of little importance for the intended use of the Software and which do not cause more than minor inconvenience for the Licensee shall not be considered as breaches of the above warranty.

7.4 THE ABOVE WARRANTY IS IAR SYSTEMS’ ONLY WARRANTY WITH REGARD TO THE SOFTWARE AND

THIS AGREEMENT AND, SAVE AS PROVIDED IN THIS AGREEMENT, NO OTHER WARRANTY OR CONDITION, EXPRESSED OR IMPLIED, WILL APPLY, AND THE LICENSEE WILL NOT RAISE ANY OTHER CLAIMS BASED ON THE PERFORMANCE OR LACK OF PERFORMANCE OF THE SOFTWARE. IAR SYSTEMS SPECIFICALLY EXCLUDES ALL OTHER WARRANTIES, REPRESENTATIONS OR UNDERTAKINGS, EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ABILITY TO ACHIEVE A PARTICULAR RESULT, OR OF ANY OTHER WARRANTY OBLIGATION ON THE PART OF IAR SYSTEMS.

7.5 IAR Systems expressly disclaims any liability for any hardware or software solutions at the Licensee which

may affect the performance of the Software, including but not limited to network configurations.

7.6 The provisions of this Article 7 shall survive any expiration or termination of this Agreement.

8. INTELLECTUAL PROPERTY INFRINGEMENT

8.1 IAR Systems will in the way set out in 8.2, and subject to all limitations therein, act on any action brought

against the Licensee to the extent it is based on a claim that the Software as it exists on the date of the Invoice infringes any patent or copyright duly issued under the laws of the country under which IAR Systems or the

579425 REV A

Page 53

IAR Software License Agreement

Licensee is organized.

8.2 IAR Systems shall, in the way set out below, as sole remedy, act on a third-party claim that the Software infringes the intellectual property rights of such party, provided that IAR Systems is given prompt notice of such claim and is given information, reasonable assistance, and sole authority to defend or settle the claim. IAR Systems may at its option obtain the right for the Licensee to continue using the infringing IAR Product, replace or modify the infringing Product until it becomes non-infringing, or if such replacement or modification is not reasonably available, terminate this license with respect to the infringing Product and provide for a reasonable refund of fees paid by the Licensee to IAR Systems for the IAR Product so affected.

8.3 IAR Systems shall not have any liability if the alleged infringement arises out of unauthorized use of the Software, postdelivery, non-IAR Systems modifications, or the combination with other products or devices not furnished by IAR Systems. THE OBLIGATIONS STATED IN THIS SECTION ARE IAR SYSTEMS’ SOLE LIABILITIES

AND THE LICENSEE’S SOLE REMEDIES FOR INFRINGEMENT OF PATENTS AND COPYRIGHTS. FOR THE AVOIDANCE OF DOUBT: THE LIABILITY OF IAR SYSTEMS UNDER THIS SECTION 8 MAY NEVER EXCEED THE LICENSE FEE PAID BY THE LICENSEE.

9. FORCE MAJEURE

9.1 Either party shall be excused from fulfilment of any obligation under this Agreement only to the extent that and for so long as such performance is prevented or delayed by an industrial dispute or any other cause beyond its reasonable control, such as, but not limited to, riots; floods; war; warlike hostilities; fires; embargo; shortage of labor, power, fuel, means of transportation, or common lack of other necessities. A party wishing to claim relief under this Article shall forthwith notify the other party in writing on the intervention and on the cessation of such circumstance.

10. LIMITATION OF LIABILITY

10.1 THE USE OF THE SOFTWARE AND ALL CONSEQUENCES ARISING THEREFROM IS THE SOLE RESPONSIBILITY OF LICENSEE. IAR SYSTEMS SHALL NOT BE LIABLE TO THE LICENSEE FOR ANY LOSS OR DAMAGE CAUSED ARISING DIRECTLY OR INDIRECTLY IN CONNECTION WITH THE SOFTWARE, THE USE OF THE SOFTWARE, OR OTHERWISE.

10.2 IAR SYSTEMS’ LIABILITY VIS-À-VIS THE LICENSEE UNDER THIS AGREEMENT SHALL UNDER ALL CIRCUMSTANCES BE LIMITED TO FIFTY (50) PER CENT OF THE LICENSE FEE FOR THE SOFTWARE PAID BY THE LICENSEE HEREUNDER, PROVIDED HOWEVER THAT IF SECTION 8 IS APPLICABLE THE TOTAL LIABILITY OF IAR SYSTEMS HEREUNDER MAY INSTEAD NEVER EXCEED 100% OF THE LICENSE FEE PAID BY THE LICENSEE HEREUNDER FOR SUCH SOFTWARE.

10.3 IAR SYSTEMS SHALL IN NO EVENT BE LIABLE TO THE LICENSEE UNDER THIS AGREEMENT FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES UNDER ANY LEGAL THEORY, SUCH AS LOSS OF DATA, USE AND/OR PROFITS, BUSINESS INTERRUPTION OR DOWNTIME COSTS AND CAPITAL COSTS OR CLAIM OF THIRD PARTY, WHETHER ON ACCOUNT OF DEFECTS, PERFORMANCES, NON-PERFORMANCES, DELAYS, PERSONAL INJURIES, PROPERTY DAMAGES, OR OTHERWISE, REGARDLESS WHETHER IAR SYSTEMS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

10.4 NOTHING IN THIS AGREEMENT SHALL EXCLUDE OR LIMIT THE LIABILIT Y UNDER APPLICABLE COMPULSORY LAW OF IAR SYSTEMS FOR DEATH OR PERSONAL INJURY RESULTING FROM ITS NEGLIGENCE.

10.5 The provisions of this Article 10 shall survive the cancellation or termination of this Agreement.

11. THIRD PARTY RIGHTS

11.1 The IAR Embedded Workbench for Eclipse includes Eclipse Materials. This License does not apply to such Eclipse Material and this is not included in the term “Software” under this License. You agree to comply with all terms and conditions imposed on you in respect of such Eclipse Materials.

11.1.1 The Eclipse Materials are licensed under the terms of the Eclipse Public License (EPL), Version 1.0, a copy of which is included in the Eclipse Materials and also available at http://www.opensource.org/licenses/ eclipse-1.0.php.

11.2 The IAR Embedded Workbench may include Third Party-Owned software. In addition to all other provisions of this License the Third Party-Owned software shall also be subject to the supplemental terms and conditions governing such Third Party-Owned software. These supplemental terms add to the terms of this License and shall supersede any inconsistent or conflicting terms in this License as they pertain to the Third Party-Owned software. If the Product the Licensee receives hereunder contains Third Party-Owned software the Licensee agree to comply with all terms and conditions imposed on you in respect of such Third Party-Owned software.

11.2.1 The Third Party-Owned Software is subject to the additional terms of each Third Party and a copy of these supplemental terms is available at http://www.iar.com/en/products/software-licenses.

12. SUPPORT AND UPDATE AGREEMENT (SUA)

12.1 Excluding what is specified in Section 12.2 and/or Section 7 of this Agreement, this Agreement does not grant the Licensee any right whatsoever to any improvements, modifications, enhancements or updates to the Software, or any other support services relating to the Software.

12.2 To the extent that the license granted includes a time-limited Support and Update Service, the Licensee

579425 REV A

Page 54

IAR Software License Agreement

will be entitled to the services defined in the Support and Update Agreement (“SUA”) attached hereto. In the case that the license granted does not include Support and Update Services or in the case where such services have expired, the Licensee may, depending on the nature of the granted license, purchase additional periods of Support and Update Services

12.3 Use of improvements, modifications, enhancements or updates received by the Licensee under IAR Systems’

Support and Update Agreement (SUA) or received under Section 7 of this Agreement, shall be governed by the terms and conditions contained herein.

13. TERMINATION OF THE AGREEMENT

13.1 IAR Systems shall have the right to terminate this Agreement with immediate effect if the Licensee is in

breach of any of its obligations under this Agreement, including, but not limited to (a) use of the Software in any manner other than pursuant to the rights granted in Article 3 and 4, (b) breach of the confidentiality provisions of Article 5, or (c) failure of the Licensee to remit payments as provided in Article 6.

13.2 This Agreement will terminate immediately without notice if Licensee suspends its payments, becomes

bankrupt or insolvent or enters into liquidation or otherwise can be regarded as insolvent.

13.3 Upon IAR Systems’ termination of this Agreement, as set out in this Article, then, IAR Systems may, at its

option, and in addition to any other rights hereunder, and in addition to any other remedies available to IAR Systems under the law, in writing require the Licensee to return or destroy all versions of the Software and the Documentation and any and all documentation relating thereto on any media and in any form in Licensee’s possession. Licensee shall give a written confirmation to IAR Systems that all material related to the Software and its operation has been returned to IAR Systems or destroyed. The provisions of this Section 13.3 shall survive the cancellation or termination of this Agreement.

14. EXPORT CONTROL REGULATIONS

14.1 The Software and the Documentation is subject to export or import regulations in various countries,

including the regulations of the United States Export Administration Act. The Licensee hereby agrees that the Licensee will not knowingly (a) export or reexport, directly or indirectly, any product or technical data or any controlled products restricted by applicable national regulations, including software, received from IAR Systems under this agreement, (b) disclose such technical data for use in, or (c) export or reexport, directly or indirectly, any direct product of such technical data or of such other controlled products, including software, to any destination to which such export or reexport is restricted or prohibited by U.S. or applicable non-U.S. law, without obtaining prior written consent of IAR Systems.

15. MISCELLANEOUS

15.1 This Agreement shall not in any situation be assignable or transferable in whole or in part by either party,

without the prior written approval of the other party. This notwithstanding, IAR Systems shall be entitled to assign this Agreement in whole or in part to a company within the IAR Systems Group, and IAR Systems may assign this Agreement without penalty or detriment to its rights under this Agreement, and without the Licensee’s prior written consent, in the event of a merger or similar reorganization or sale of substantially all of IAR Systems’ assets.

15.2 No alteration or amendment to this Agreement shall be valid unless such alteration or amendment is made

in writing and signed by the parties hereto.

15.3 Any notice or other communication under this Agreement shall be made in writing either by hand or by

telefax (confirmed by airmail) or by certified or registered airmail first-class postage prepaid to the parties at the addresses stated in the Invoice (or at such other address a party may specify by written notice to the other).

15.4 This Agreement contains the entire understanding between the parties on its subject matter, and annuls

and replaces any other agreements or understandings, whether written or oral, which may exist or have existed between the parties on the subject matter hereof.

15.5 This Agreement shall be governed by and construed in accordance with the substantive to the courts of

the country in which IAR Systems is incorporated. Any dispute concerning this agreement or the interpretation or validity thereof, or any other dispute based thereon, shall be submitted to the courts of the country in which IAR Systems is incorporated.

15.6 The provisions of this Article 15 shall survive the cancellation or termination of this Agreement.

This document contains Third Party Software Notices and/or Additional Terms and Conditions for licensed third party software components included within IAR Systems software product IAR Embedded Workbench. These notices and/or additional terms and conditions are made a part of and incorporated by reference into the IAR Software License Agreement.

579425 REV A

Page 55

IAR Software License Agreement

1. Components used internally in IAR Embedded Workbench

Third Party

Software

SCINTILLA

IBM ICU

Notice/Terms

License for Scintilla and SciTE Copyright 1998-2002 by Neil Hodgson. All Rights Reserved. Permission to use, copy, modify, and distribute this software and its documentation for any purpose and without fee is hereby granted, provided that the above copyright notice appear in all copies and that both that copyright notice and this permission notice appear in supporting documentation. NEIL HODGSON DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFT WARE,INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL NEIL HODGSON BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE

ICU License - ICU 1.8.1 and later COPYRIGHT AND PERMISSION NOTICE Copyright (c) 1995-2003 International Business Machines Corporation and others All rights reserved. Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, provided that the above copyright notice(s) and this permission notice appear in all copies of the Software and that both the above copyright notice(s) and this permission notice appear in supporting documentation. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS NOTICE BE LIABLE FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization of the copyright holder. All trademarks and registered trademarks mentioned herein are the property of their respective owners

579425 REV A

Page 56

IAR Software License Agreement

The Apache Software License, Version 1.1 Copyright (c) 1999-2003 The Apache Software Foundation. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. The end-user documentation included with the redistribution, if any, must include the following acknowledgment: “This product includes software developed by the Apache Software Foundation (http://www.apache.org/).” Alternately, this acknowledgment may appear in the software itself, if and wherever such third-party acknowledgments normally appear.

4. The names “Xerces” and “Apache Software Foundation” must not be used to endorse or promote products derived from this software without prior written permission. For written

Apache

LLVM

permission, please contact apache@apache.org.

5. Products derived from this software may not be called “Apache”, nor may “Apache” appear in their name, without prior written permission of the Apache Software Foundation. THIS SOFTWARE IS PROVIDED ``AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE APACHE SOFTWARE FOUNDATION OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOTLIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This software consists of voluntary contributions made by many individuals on behalf of the Apache Software Foundation and was originally based on software copyright (c) 1999, International Business Machines, Inc., http://www.ibm.com. For more information on the Apache Software Foundation, please see <http://www.apache.org/>

LLVM Release License University of Illinois/NCSA. Open Source License. Copyright (c) 2003-2011 University of Illinois at Urbana-Champaign. All rights reserved. Developed by: LLVM Team University of Illinois at Urbana-Champaign. http://llvm.org Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal with the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimers. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimers in the documentation and/or other materials provided with the distribution. * Neither the names of the LLVM Team, University of Illinois at Urbana-Champaign, nor the names of its contributors may be used to endorse or promote products derived from this Software without specific prior written permission. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE CONTRIBUTORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS WITH THE SOFTWARE..

579425 REV A

Page 57

Boost C++

Libraries

Protocol

Buffers

IAR Software License Agreement

Boost Software License - Version 1.0 - August 17th, 2003 Permission is hereby granted, free of charge, to any person or organization obtaining a copy of the software and accompanying documentation covered by this license (the “Software”) to use, reproduce, display, distribute, execute, and transmit the Software, and to prepare derivative works of the Software, and to permit third-parties to whom the Software is furnished to do so, all subject to the following: The copyright notices in the Software and this entire statement, including the above license grant, this restriction and the following disclaimer, must be included in all copies of the Software, in whole or in part, and all derivative works of the Software, unless such copies or derivative works are solely in the form of machine-executable object code generated by a source language processor. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT. IN NO EVENT SHALL THE COPYRIGHT HOLDERS OR ANYONE DISTRIBUTING THE SOFTWARE BE LIABLE FOR ANY DAMAGES OR OTHER LIABILITY, WHETHER IN CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Protocol Buffers - Google’s data interchange format Copyright 2008 Google Inc. All rights reserved. http://code.google.com/p/protobuf/ Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. * Neither the name of Google Inc. nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

2. Components potentially used in customer applications

Third Party

Notice/Terms

Software

dlmalloc

579425 REV A

Version of malloc/free/realloc (aka dlmalloc) written by Doug Lea and released to the public domain, as explained at http://creativecommons.org/publicdomain/zero/1.0/.

Page 58

IAR Software License Agreement

Dinkum Abridged/C Library Sub license Denition: The term “Licensed Source” shall mean the Dinkum Abridged Library source code, the

Dinkum C Library source code and the Dinkum Abridged Library Reference, or a later version of the same products. A Sub license is granted solely in conjunction with, and for use with IAR C/EC++/ C++ Cross Compiler owned by IAR Systems AB. The Sub Licensee shall supply to Dinkumware Ltd (“Licensor”) with the following protections:

(a)Plauger’s ownership. a.Sub Licensee acknowledges and agrees that: *Title and all rights of ownership to the Licensed Source, and all copies of all or any part thereof, are and remain with Plauger; *Sub Licensee shall not lend, sell, lease, hypothecate or otherwise dispose of the Licensed Source. *All copies of the Licensed Source, or any part thereof, in any form whatsoever, including but not limited to, forms cognizable to the human eye (directly, or upon enlargement or translation), or to data processing or other equipment, shall be the sole and exclusive property of Plauger, as described immediately above; and *Licensor has represented that the Licensed Source may contain Licensor’s trade secrets and proprietary information, whether or not any portion thereof is or may be copyrighted or patented. b.Sub Licensee agrees to preserve unchanged all copyright notices in all copies of the Licensed Source. c.Licensor acknowledges and agrees that Sub Licensee shall have no obligation to deliver or disclose to Licensor any modications that Sub Licensee makes to the Licensed Source, ant that Sub Licensee shall own and have exclusive marketing rights to any such undisclosed modications. d.Sub Licensee acknowledges and agrees that any modications that Sub Licensee makes to the Licensed Source and discloses to Licensor, unless otherwise indicated in writing by Sub Licensee on or before disclosure (“Disclosed Modications”), shall become the property of Plauger. Disclosed Modications to the Licensed Library Source shall become the property of Plauger. Sub Licensee hereby assigns to Plauger all of Sub Licensee’s right, title, and interest in and to such Disclosed Modications and in and to the copyrights and all

Dinkum C++ Library

other rights in the Disclosed Modications. (b) License. a.Licensor hereby grants to Sub Licensee a personal, non-exclusive, and non-transferable license to use or modify the Licensed Source for its own internal business purposes solely in conjunction with IAR C/EC++/C++ Cross Compiler owned by IAR Systems. b.Notwithstanding the foregoing, Sub Licensee may make only such copies of the Licensed Source as are reasonably necessary for it to exercise its right hereunder. Sub Licensee acknowledges that it may not sell, assign, sublicense, lease or otherwise transfer, or permit others to use or execute the Licensed Source, or any port thereof, or any modication or improvement of the Licensed Source, or any object code which is derived from the Licensed Source. c.Sub Licensee agrees to comply with all applicable laws, regulations, rulings, and executive order from the United States relating to the export or re-export of the Licensed Source, and with all applicable foreign laws which must be complied with in order to protect or preserve Licensor’s copyright(s), trade secret(s), and other proprietary rights in and to the Licensed Source. Sub Licensee agrees that it will not knowingly ship or divert the Licensed Source for use in any country which has ratied neither the Berne Copyright Convention nor the Universal Copyright Convention without rst obtaining written permission from Licensor. (c)Warranty and Disclaimer of Warranty. a.Licensor warrants that, at the time of delivery, the Licensed Source will be in good operating condition and will be Standard Conforming in all essential respects. b.Licensor represents and warrants that it is not aware that the Licensed Source is created in whole or in part by violation of the protected trade secret of another or that the Licensed Source infringes any U.S. patent or copyright.

c.THE FOREGOING LIMITED WARRANTIES ARE THE ONLY WARRANTIES OF LICENSOR TO SUB LICENSEE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

(d)Limitation of Liability. a.In no event shall Licensor be liable to Sub Licensee for any lost prots, incidental, special, exemplary, punitive, indirect or other consequential dam ages, even if Licensor knows or has been advised of the possibility of such damages, or for any claim against Sub Licensee by any other person or entity, or for any damage caused by Sub Licensee’s failure to perform its responsibilities.

Updated: 2013-02-15. IAR Systems AB.

579425 REV A

Page 59

Freescale MQX RTOS 4.0.2

IMPORTANT. Read the following Freescale Semiconductor Software License Agreement (“Agreement”) completely. By selecting the “I Accept” button below, you indicate that you accept the terms of this Agreement. You may then install the software.

FREESCALE SEMICONDUCTOR SOFTWARE LICENSE AGREEMENT

This is a legal agreement between you (either as an individual or as an authorized representative of your employer) and Freescale Semiconductor, Inc. (“Freescale”). It concerns your rights to use this file and any accompanying written materials (the “Software”). In consideration for Freescale allowing you to access the Software, you are agreeing to be bound by the terms of this Agreement. If you do not agree to all of the terms of this Agreement, do not download the Software. If you change your mind later, stop using the Software and delete all copies of the Software in your possession or control. Any copies of the Software that you have already distributed, where permitted, and do not destroy will continue to be governed by this Agreement. Your prior use will also continue to be governed by this Agreement.

LICENSE GRANT. Exclusively in conjunction with Licensee’s development and sale of a product containing a programmable processing unit (e.g., a microprocessor, microcontroller, or digital signal processor) supplied directly or indirectly from Freescale (“Freescale System”)and listed under “By Products” on the Freescale MQX website (www.freescale.com/mqx), Freescale grants to you, free of charge, the non-exclusive, non-transferable right (1) to use the Software, (2) to reproduce the Software, (3) to prepare derivative works of the Software, (4) to distribute the Software and derivative works thereof in object (machine-readable) form as part of a Freescale System, and (5) to sublicense to others the right to use the distributed Software as included within the Freescale System. You must prohibit your sublicensees from translating, reverse engineering, decompiling, or disassembling the Software except to the extent applicable law specifically prohibits such restriction. If you violate any of the terms or restrictions of this Agreement, Freescale may immediately terminate this Agreement, and require that you stop using and delete all copies of the Software in your possession or control.

COPYRIGHT. The Software is licensed to you, not sold. Freescale owns the Software, and United States copyright laws and international treaty provisions protect the Software. Therefore, you must treat the Software like any other copyrighted material (e.g. a book or musical recording). You may not use or copy the Software for any other purpose than what is described in this Agreement. Except as expressly provided herein, Freescale does not grant to you any express or implied rights under any Freescale or third-party patents, copyrights, trademarks, or trade secrets. Additionally, you must reproduce and apply any copyright or other proprietary rights notices included on or embedded in the Software to any copies or derivative works made thereof, in whole or in part, if any.

SUPPORT. Freescale is NOT obligated to provide any support, upgrades or new releases of the Software. If you wish, you may contact Freescale and report problems and provide suggestions regarding the Software. Freescale has no obligation whatsoever to respond in any way to such a problem report or suggestion. Freescale may make changes to the Software at any time, without any obligation to notify or provide updated versions of the Software to you.

NO WARRANTY. TO THE MAXIMUM EXTENT PERMITTED BY LAW, FREESCALE EXPRESSLY DISCLAIMS ANY WARRANTY FOR THE SOFTWARE. THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. YOU ASSUME THE ENTIRE RISK ARISING OUT OF THE USE OR PERFORMANCE OF THE SOFTWARE, OR ANY SYSTEMS YOU DESIGN USING THE SOFTWARE (IF ANY). NOTHING IN THIS AGREEMENT MAY BE CONSTRUED AS A WARRANTY OR REPRESENTATION BY FREESCALE THAT THE SOFTWARE OR ANY DERIVATIVE WORK DEVELOPED WITH OR INCORPORATING THE SOFTWARE WILL BE FREE FROM INFRINGEMENT OF THE INTELLECTUAL PROPERTY RIGHTS OF THIRD PARTIES.

INDEMNITY. You agree to fully defend and indemnify Freescale from any and all claims, liabilities, and costs (including reasonable attorney’s fees) related to (1) your use (including your sublicensee’s use, if permitted) of the Software or (2) your violation of the terms and conditions of this Agreement.

LIMITATION OF LIABILITY. IN NO EVENT WILL FREESCALE BE LIABLE, WHETHER IN CONTRACT, TORT, OR OTHERWISE, FOR ANY INCIDENTAL, SPECIAL, INDIRECT, CONSEQUENTIAL OR PUNITIVE DAMAGES, INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, OR LOST PROFITS, SAVINGS, OR REVENUES TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. COMPLIANCE WITH LAWS; EXPORT RESTRICTIONS. You must use the Software in accordance with all

579425 REV A

Page 60

Freescale MQX RTOS 4.0.2

applicable U.S. laws, regulations and statutes. You agree that neither you nor your licensees (if any) intend to or will, directly or indirectly, export or transmit the Software to any country in violation of U.S. export restrictions.

GOVERNMENT USE. Use of the Software and any corresponding documentation, if any, is provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of The Rights in Technical Data and Computer Software clause at DFARS 252.2277013 or subparagraphs (c)(l) and (2) of the Commercial Computer Software — Restricted Rights at 48 CFR

52.227-19, as applicable. Manufacturer is Freescale Semiconductor, Inc., 6501 William Cannon Drive West,

Austin, TX, 78735.

HIGH RISK ACTIVITIES. You acknowledge that the Software is not fault tolerant and is not designed, manufactured or intended by Freescale for incorporation into products intended for use or resale in on-line control equipment in hazardous, dangerous to life or potentially life-threatening environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, direct life support machines or weapons systems, in which the failure of products could lead directly to death, personal injury or severe physical or environmental damage (“High Risk Activities”). You specifically represent and warrant that you will not use the Software or any derivative work of the Software for High Risk Activities.

CHOICE OF LAW; VENUE; LIMITATIONS. You agree that the statutes and laws of the United States and the State of Texas, USA, without regard to conflicts of laws principles, will apply to all matters relating to this Agreement or the Software, and you agree that any litigation will be subject to the exclusive jurisdiction of the state or federal courts in Texas, USA. You agree that regardless of any statute or law to the contrary, any claim or cause of action arising out of or related to this Agreement or the Software must be filed within one (1) year after such claim or cause of action arose or be forever barred.

PRODUCT LABELING. You are not authorized to use any Freescale trademarks, brand names, or logos.

ENTIRE AGREEMENT. This Agreement constitutes the entire agreement between you and Freescale regarding

the subject matter of this Agreement, and supersedes all prior communications, negotiations, understandings, agreements or representations, either written or oral, if any. This Agreement may only be amended in written form, executed by you and Freescale.

SEVERABILITY. If any provision of this Agreement is held for any reason to be invalid or unenforceable, then the remaining provisions of this Agreement will be unimpaired and, unless a modification or replacement of the invalid or unenforceable provision is further held to deprive you or Freescale of a material benefit, in which case the Agreement will immediately terminate, the invalid or unenforceable provision will be replaced with a provision that is valid and enforceable and that comes closest to the intention underlying the invalid or unenforceable provision.

NO WAIVER. The waiver by Freescale of any breach of any provision of this Agreement will not operate or be construed as a waiver of any other or a subsequent breach of the same or a different provision.

579425 REV A

Page 61

99 Washington Street Melrose, MA 02176

Phone 781-665-1400 Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

579425 REV A

Robinair Robinair AC1234-4 Manual

Specifications and Main Features

Frequently Asked Questions

User Manual