Page 1
1
Version 1.5
Page 2
2
Table of contents
1. Safety instructions ......................................................................................................... 3
2. Operating determination ................................................................................................ 4
3. Fixture exterior view ...................................................................................................... 5
4. Installation....................................................................................................................... 6
4.1 Connection to the mains ............................................................................................ 6
4.2 Eggcrate installation ................................................................................................... 6
4.3 Rigging the xture ...................................................................................................... 7
4.4 DMX-512 connection .................................................................................................. 9
4.5 Ethernet connection ................................................................................................. 10
4.6 Wireless DMX operation .......................................................................................... 12
5. Remotely controllable functions ................................................................................. 13
6. Control menu map ........................................................................................................ 15
7. Control menu ............................................................................................................... 18
7.1 Tab " Address" .......................................................................................................... 19
7.2 Tab "Information" ...................................................................................................... 20
7.3 Tab "Personality" ......................................................................................................21
7.4 Tab "Manual Control" ................................................................................................ 23
7.5 Tab "Stand-alone" .................................................................................................... 23
7.6 Tab "Service" ............................................................................................................ 24
8. RDM ............................................................................................................................... 25
9. Error and information messages ................................................................................ 27
10. Technical Specications ............................................................................................ 28
11. Maintenance and cleaning ......................................................................................... 31
11.1 Removing the optical module ................................................................................. 32
11.2 Disposing of the product ......................................................................................... 33
12. ChangeLog .................................................................................................................. 33
13. Photometric diagrams................................................................................................ 34
Robin Spiider
Page 3
3
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOU INITIAL START - UP!
1. Safety instructions
Every person involved with installation and maintenance of this device have to:
- be qualied
- follow the instructions of this manual
CAUTION!
Be careful with your operations.
With a high voltage you can suer
a dangerous electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
Important
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
Handle the power cord and all connections with the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear panel.
WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable
to completely remove power from unit when not in use or before cleaning or servicing the unit.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the pow-
er-cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-cord by the plug. Never pull out the plug by tugging the power cord.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to earth.
The electric connection, repairs and servicing must be carried out by a qualied employee.
Do not connect this device to a dimmer pack.
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!
For replacement use fuses of same type and rating only.
Warning! Risk Group 2 LED product according to EN 62471.
LED light emission. Risk of eye injury. Do not look into the beam at short distance of
the of the product. Do not view the light output with optical instruments or any device
that may conncentrate the beam.
The light source contains blue LEDs.
Page 4
4
2. Operating determination
This device is a moving head for creating decorative eects and was designed for indoor use only.
This device is for professional use only. It is not for household use.
If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched o until
it has reached room temperature.
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the xture by holding it at the projector head, as the mechanics may be damaged. Always hold the
xture at the transport handles.
When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture
or dust. There should not be any cables lying around. You endanger your own and the safety of others!
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.
Always secure the xture with an appropriate safety wire.
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fastened.
The maximum ambient temperature 45°C must never be exceeded.
To avoid damage of an internal optical system of the xture, never let the sunlight (or
other light source) lights directly to the lens array, even when the xture is not working
!
Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the device. Most damages are the result of unprofessional operation!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modications on the device are forbidden due to safety reasons!
If this device will be operated in any way dierent to the one described in this manual, the product may suer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns, electric shock, burns etc.
Always push the zoom module into the head before inserting the xture into the ight
case.
Page 5
5
3. Fixture exterior view
The head should be locked for transportation - the tilt lock latch (7) has to be in the locked position. To unlock
the head, move this latch to unlock position before operating the xture.
The ENTER/DISPLAY ON button also serves for switching the display on when the xture is disconnected
from the mains.
1 - Lens array
2 - Yoke
3 - Handle
4 - QVGA touch screen
5 - Control buttons
6 - USB port
7 - Tilt lock
8 - 3-pin DMX OUT
9 - Ethernet IN
10 - Base
11 - Ethernet OUT
12- 3-pin DMX IN
13- 5-pin DMX IN
14- Mains IN
15- Fuse holder
16- 5-pin DMX OUT
17- Moving head
Page 6
6
4. Installation
Fixtures must be installed by a qualied electrician in accordance with all
national and local electrical and construction codes and regulations.
4.1 Connection to the mains
For protection from electric shock, the xture must be earthed!
The Robin Spiider is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC
power source from 100-240 Volts.
If you install a cord cap on the power cable to allow connection to power outlets, install a grounding-type (earthed)
plug, following the plug manufacturer’s instructions.
The cores in the power cable are coloured according to the following table.
Core (EU) Core (US) Connection Plug Terminal Marking
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth
This device falls under class one and must be earthed (grounded)!
To apply power, rst check that the head pan and tilt locks are released.
Wiring and connection work must be carried out by qualied sta!
4.2 Eggcrate installation
Disconnect the xture from mains before eggcrate installation
Screw the eggcrate (1) to the head (3) by means of the three screws (2).
Page 7
7
4.3 Rigging the xture
A structure intended for installation of the xture (s) must safely hold weight of the xture(s) placed on it. The
structure has to be certicated to the purpose.
The xture (xtures) must be installed in accordance with national and local electrical and construction codes
and regulations.
For overhead installation, the xture must be always secured with a safety wire that
can bear at least 10 times the weight of the xture.
When rigging, derigging or servicing the xture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert before taking into operation for the rst time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
Allow the xture to cool for ten minutes before handling.
The xture should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working
load limits, installation material being used, and periodic safety inspection of all installation material and the
projector. If you lack these qualications, do not attempt the installation yourself, but use a help of professional
companies.
CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety
of a possible installation, do not install the xture!
The xture has to be installed out of the reach of public.
The xture must never be xed swinging freely in the room.
Danger of re !
When installing the device, make sure there is no highly inammable
material (decoration articles, etc.) in a distance of min. 0.5 m.
CAUTION!
Use 2 appropriate clamps to rig the xture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is xed properly! Ensure that the
structure (truss) to which you are attaching the xtures is secure.
The xture can be placed directly on the stage oor or rigged in any orientation on a truss without altering its
operation characte ristics .
For securing the xture to the truss, install a safety wire which can hold at least 10 times the weight of the xture.
Use only the safety wire with a snap hook with screw lock gate.
.
.
Page 8
8
Truss installation
1. Bolt the clamp (3) to the omega holder (5) with M12 bolt and lock nut through the hole in the holder.
2. Fasten the omega holders to the bottom of the base by inserting both quick-lock fasteners (2) into
the holes of the base and tighten fully clockwise.
3. Clamp the xture on a truss (6) and tighten the rigging clamps.
4. Pull the safety wire (4) through the attachment point (1) and through the handle (7) and around the truss (6)
and lock the snap hook with screw lock gate.
Use only a safety wire with a snap hook with screw lock gate.
When installing xtures side-by-side,
avoid illuminating one xture with another!
DANGER TO LIFE!
Before taking into operation for the rst time,the installation has to be approved by
an expert!
Page 9
9
4.4 DMX-512 connection
The xture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired
in parallel.
Only use a shielded twisted-pair cable designed for RS-485 and 3-pin or 5-pin XLR-plugs and connectors in
order to connect the controller with the xture or one xture with another.
DMX - output DMX-input
XLR mounting-sockets (rear view): XLR mounting-plugs (rear view):
If you are using the standard DMX controllers, you can connect the DMX output of the controller directly with
the DMX input of the rst xture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the rst xture in the DMX-chain with the DMX-input of the next xture. Always connect
one output with the input of the next xture until all xtures are connected. Up to 32 xtures can be connected.
Caution: At the last xture, the DMX-cable has to be terminated with a terminator. Solder a 120 Ω resistor
between Signal (–) and Signal (+) into a 3-pin (5-pin) XLR-plug and plug it in the DMX output of the last xture.
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
1 - Shield
2 - Signal (-)
3 - Signal (+)
4 - Not connected
5 - Not connected
Page 10
10
4.5 Ethernet connection
The xtures on a data link are connected to the Ethernet with ArtNet communication protocol.The control software running on your PC (or light console) has to support Art-Net protocol.
Art-Net communication protocol is a 10 Base T Ethernet protocol based on the TCP/IP.Its purpose is to allow
transfer of large amounts of DMX 512 data over a wide area using standard network technology.
IP address is the Internet protocol address.The IP uniquely identies any node (xture) on a network.
The Universe is a single DMX 512 frame of 512 channels.
The Robin Spiider is equipped with 8-pin RJ- 45 socket for Ethernet input.Use a network cable category 5 (with
four “twisted” wire pairs) and standard RJ-45 plugs in order to connect the xture to the network.
RJ-45 socket (front view): RJ-45 plug (front view):
1- TD+ 5- Not connected
2- TD- 6- RX-
3- RX+ 7- Not connected
4- Not connected 8- Not connected
Patch cables that connect xtures to the hubs or LAN sockets are wired 1:1,that is,pins with the same numbers
are connected together:
1-1 2-2 3-3 4-4 5-5 6-6 7-7 8-8
If only the xture and the computer are to be interconnected,no hubs or other active components are needed.A
cross-cable has to be used:
1-3 2-6 3-1 4-8 5-7 6-2 7-5 8-4
If the xture is connected with active Ethernet socket (e.g. switch) the network icon will appear at the
bottom right corner of the screen:
Direct Ethernet operation
Connect the Ethernet inputs of all xtures with the Ethernet network.
Option “Artnet (gMaI or gMA2)" has to be selected from “Ethernet Mode” menu on the xture.
Set IP address (002.xxx.xxx.xxx / 010.xxx.xxx.xxx) and the Universe.
(DMX address=131) (DMX address=30) (DMX address=1)
IP addres=002.168.002.004 IP addres=002.168.002.003 IP addres=002.168.002.002
Universe=1 Universe=1 Universe=1
An advised PC setting: IP address: 002.xxx.xxx.xxx / 010.xxx.xxx.xxx (Dierent from xture IP addresses)
NET mask: 255.0.0.0
Page 11
11
Ethernet / DMX operation
Options “Art2DMX” has to be selected from the “Ethernet Mode” menu on the rst xture (connected to the
Ethernet) in the xture chain,next xtures have standard DMX setting.
Connect the Ethernet-input of the rst xture in the data chain with the network. Connect the DMX output of
this xture with the input of the next xture until all xtures are connected to the DMX chain.
Caution: At the last xture, the DMX chain has to be terminated with a terminator. Solder a 120 Ω resistor
between Signal (–) and Signal (+) into a XLR-plug and connect it in the DMX-output of the last xture.
Example:
DMX address=1 DMX address=49 DMX address=131
IP addres=002.168.002.002
Universe=0
DMX address=1 DMX address=49 DMX address=131
IP addres=002.168.002.003
Universe=1
Page 12
12
4.6 Wireless DMX operation
The wireless version of the Robin Spiider is equipped with the Lumen Radio CRMX module and antenna for
receiving DMX signal. CRMX module operates on the 2.4 GHz band.
The item " Wireless " from the menu "DMX Input" allows you to activate receiving of wireless DMX (Personality--> DMX Input -->Wireless.). First two options from the "DMX Input" menu are stated in DMX chart as well
(channel Power/Special functions , range of 10-19 DMX). If DMX input option is changed by DMX command,
the change is permanently written into xture´s memory.
DMX range of 10-19 switching xture to the wired/wireless operation is active only during rst 10 seconds after switching the xture on.
After switching the xture on, the xture checks both modes of receiving DMX in the following order:
1. For the rst ve seconds, the xture receives DMX signal from the wired input. If the Power/Special functions
channel is set at some DMX input option, the xture will receive DMX value according to this option. If DMX input
option is set to the wired input , this option is saved and checking procedure is nished. If DMX input option is
not set, the xture continues next 5 seconds in scanning wireless DMX signal-see point 2.
2. For the next 5 seconds the xture receives wireless DMX signal and again detects if the Power/Special
functions channel is set at some DMX input option, if not, the xture will take option which is set in the xture
menu "DMX Input".
To link the xture with DMX transmitter.
The xture can be only linked with the transmitter by running the link procedure at DMX transmitter .
After linking , the level of DMX signal ( 0-100 %) is displayed in the menu item “Wireless State“ (Information
-->Wireless State).
To unlink the xture from DMX transmitter.
The xture can be unlinked from receiver via the menu item “ Unlink Wireless Adapter“ (Information--> Wireless
State --> Unlink Wireless Adapter.).
Note: If the option "Wireless In/XLR Out" is selected (Personality--> DMX Input -->Wireless In/XLR Out), the
xture receives wireless DMX and sends the signal to its wired DMX output. The xture behaves as " Wireless/
Wired" adapter.
Example:
Page 13
13
5. Remotely controllable functions
Virtual colour wheel
This wheel contains 66 preset colours, rainbow eect in both directions is available.
Colour temperarature correction (CTC)
This channel allows to set calibrated white colour from range of 8000K-2700K.
RGBW or CMY colour mixing system
The RGBW colour mixing system is based on red, green, blue and white high power LEDs. Option for switching
the xture to the CMY colour mixing system is available.
Colour Mix control
The Colour Mix control channel denes relation between global colours (RGBW, CTO, Virtual colour wheel)
and individual RGB pixels or Kling-Net.
Global = Global Colours (RGBW, CTO, Virtual Color Wheel)
Pixel = Pixel Colors (RGB individual pixels or Kling-Net)
DMX value Function
0-9 Global colours (Global has priority)
10-19 Maximum mode (highest values have priority)
20-29 Minimum mode (lowest values have priority)
30-39 Multiply mode (multiply Global and Pixel)
40-49 Addition mode (Global + Pixel) - default
50-59 Subtraction mode (Global – Pixel)
60-69 Inverted Subtraction mode (Pixel – Global)
70-79 Coloured background
80-127 Reserved
128 Global colours (Global has priority)
129-254 Crossfade (crossfade between Global and Pixel)
255 Pixel colours (Pixel has priority)
E.g. If you wish to control RGBW channels, set the Colour Mix Control channel to 0 DMX, if you
need to use pixel eects, set the Colour Mix Control channel to 255 DMX.
Flower Eect
The ower eect rotating in both directions allows to create many dynamic eects.
Zoom
Motorized zoom oers beam range of 4° to 50°.
Pixel control and pixel eects
19 RGB pixels allow you to create many eects or use 90 pre-dened pixel eects
Pixel order:
Dimmer/Shutter unit
Smooth 0 - 100 % dimming is provided by the electronic control unit. This unit is also used for strobe eects
with variable speed.
Page 14
14
Pan/Tilt
Precise pan/tilt movement due to built-in electronic motion stabilizer. The electronic motion stabilizer ensures
precise position of the xture´s head during its movement and reduces its swinging when the truss shakes.
Pan movement range: 540°,tilt movement range: 230°.
Page 15
15
6. Control menu map
Default settings=Bold print
Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
Addressing Settings DMX Address 001-255
-
DMX Preset Mode 1, Mode 2,
Mode 3, Mode 4
Ethernet Settings Ethernet Mode Disable
ArtNet
gMAI
gMA2
sACN
Ethernet To DMX O, On
IP Address/Net Mask Default IP Address
Custom IP Address
Net Mask
ArtNet Universe 0-255
MANet settings MANetI/II Universe 01-256
MANet Session ID 01-32
sACN Settings sACN Universe 00001-32000
sACN Priority 0-255
Klingnet Settings Disable
Enable
Information Fixture Times Power On Time Total Hours
Resetable Hours
Air Filters Elapsed Time
Alert Period 10-300
Fixture Temperatures
LEDs Temperature Current
Maximum NonRes.
Maximum Res.
Base Temperature Current
Maximum NonRes.
Maximum Res.
DMX Values Pan
:
Blue Pixel 19
Wireless State Signal Quality
Unlink Wireless
Adapter
Power Channel State
Software Versions Display System
Module M
Module DR
Module PX
Product IDs Mac Address
RDM UID
RDM Label
View Logs Fixture Errors
Fixture States Power On
Power O
Fixture Position
Fixture Temperatures LEDs Temperatures
Base Temperatures
Page 16
16
Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
Personality
DMX Presets Mode 1
:
Mode 6
:
Mode 10
View Selected Preset
DMX Input Wired Input
Wireless Input
Wireless In/XLR Out
Pan/Tilt Settings Pan Reverse O, On
Tilt Reverse O, On
Pan/Tilt Feedback O, On
Pan/Tilt mode Time
Speed
Pan/Tilt EMS On, O
Microphone Sensitivity
1-10-20
Blackout Settings Blackout During M.C. O, On
Blackout while: Pan/Tilt moving O, On
Colour Mixing Mode
RGBW
CMY
White Point 8000K O, On
Tungsten E. Sim. O
750W
1000W
1200W
2000W
2500W
Dimmer Curve Linear
Square Law
Init Eect Positions Pan 0-255
:
Dimmer Fine 0-255
Screen Settings Display Intensity 1-10
Screen Saver Delay O-10min.
Touchscreen Lock O-10min.
Recalibrate Touchscreen
Display Orientation Normal
Inverted
Auto
Temperature Unit °C,°F
Fan Mode Auto
High
Date & Time Settings
Default Settings
Manual Control Reset Functions Total System reset
Pan/Tilt reset
Zoom Reset
Flower E. Reset
Manual Eect Con-
trol
Pan 0-255
:
Blue Pixel 19 0-255
Page 17
17
Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
Stand -Alone Test Sequences Dynamic Mode
Static Mode Pan 0-255
Tilt 0-255
Zoom 0-255
MusicTrigger O, On
Preset Playback None
Test
Prog. 1
Prog. 2
Prog. 3
Play Program Play Program 1
Play Program 2
Play Program 3
Edit Program Edit Program 1 Start Step 1-100
End Step 1-100
Edit Program Steps Step 1 Pan 0-255
: :
: Dimmer Fine 0-255
: Step Time 0-25,5 sec.
Step 100 Pan 0-255
:
Dimmer Fine 0-255
Step Time 0-25,5 sec.
Service Adjust DMX Values Pan 0-255
:
Blue Pixel 19 0-255
Calibrations Calibrate Eects Pan 0-255
Tilt: 0-255
Calibrate colours Red 0-255
Green 0-255
Blue 0-255
White 0-255
Calibrate Pan/Tilt EMS
Load Default Calib-
rations
Update Software
Page 18
18
7. Control menu
The Robin Spiider Light is equipped with the QVGA Robe touch screen with battery backup which
allows to set the xture´s behaviour according to your needs, obtain information on its operation, test its
various parts and lastly program it, if it has to be used in a stand-alone mode.
The xture´s menu can be controlled either by the control buttons or directly by touching the icon.
Control buttons on the front panel:
[ESCAPE] button used to leave the menu without saving changes.
[NEXT] , [PREV] buttons for moving between menu items and symbols, adjusting values.
[ENTER/Display On] button used to enter the selected menu (menu item) and to conrm adjusted value.
If the xture is disconnected from mains, the button switches the touch screen on.
Icons used in the touch screen menu:
- [back arrow] used to move back to the previous screen (menu).
- [up arrow] used to move up on the previous page.
- [down arrow] used to move down on the next page.
- [conrm] used to save adjusted values, to leave menu or to perform desired action.
- [cancel] used to leave menu item without saving changes.
- [conrm+copy] used to save adjusted values and copy them to the next prog. step.
- [warning icon] used to indicate some error which has occurred in the xture.
- [Ethernet] used to indicate Ethernet connected.
- [display turn] used to turn the display by 180°.
- [slider control] used to recall slider system for setting desired value.
- [keyboard control] used to recall keyboard system for setting desired value.
- [air lters cleaning] used to signal that cleaning period of the air lters elapsed.
The menu page displays icons for each function that you can perform from the touch screen.
After switching the xture on, the touch screen shows the screen with the ROBE logo:
Page 19
19
Note: The green icon at the top right corner of the screen indicates the level of the display battery charging. If
the whole icon is green, the battery is fully charged while the red icon indicates exhausted battery. The battery
charges during xture operation, its charging lasts cca 6 hours.
We recommend that the xture should be in operation at least 7 hours per week to keep the battery fully charged.
If you switch the xture on and this screen will not appear till 1 minute, switch the xture o and on again. If the
screen lights, the battery is exhausted. In case the screen still does not light, the battery is faulty.
This is also indicated by an error message "Faulty battery" and if such an error message appears the battery
should be replaced immediately. The lifetime of the battery is highly dependent on ambient temperature (and
consequently on base temperature). If the maximum ambient temperatures (as recorded and displayed in menu:
Information -> Fixture Temperatures -> Ambient Temperature -> Maximum NonRes.) are kept within the specied limits, the battery should last for at least two years. Shell the ambient temperatures exceed the specied
maximum temperature, the lifetime of the batteries could be considerably shortened even up to just one year
or less and also result in physical damage (battery leakage) or unreliable xture functions.
Damage caused by batteries failed due to exceeded maximum ambient temperature cannot be claimed under
warranty terms.
Touch any part of the screen or press the [ENTER/Display On] button to display the initial screen with the current stored DMX address:
Touch the green arrow at the bottom right corner of the screen or press the [ENTER/Display On] button to enter
the " Address" menu.
Each item (such as a Tab, menu item, text box, icon) may be selected from a screen by simply touching the
item in the list or by pressing the [NEXT] or [PREV] buttons to scroll through list items. With each press, the
next item is highlighted. Press [ENTER/Display On] to select the highlighted item.
Before rst xture operation, set current date and time in the menu "Date &Time
Setings" (menu path: Personality--> Date &Time Setings).
7.1 Tab " Address"
DMX Address - Select the menu to set the DMX start address.
DMX Preset - Use the menu to select desired channel mode.
View Selected Preset - Use the menu to display channels included in the selected mode.
Ethernet Settings - The menu allows all needed settings for the Ethernet operation
Ethernet Mode
Disable - The option disables Ethernet operation.
Artnet - Fixture
receives Artnet protocol
gMAI
- Fixture
receives MANet I protocol
gMA2
- Fixture
receives MANet 2 protocol
sACN
- Fixture
receives sACN protocol
Ethernet To DMX - Fixture receives
protocol
from the Ethernet input and sends DMX
data to its DMX output (xture works as an "Ethernet/DMX converter",
next xture can be connected
to its DMX output and you can build a standard DMX chain by connecting another xtures.
Only one xture has to be connected to the Ethernet.
Page 20
20
IP Address/Net Mask - Select this menu to set IP address. IP address is the Internet protocol
address.The IP uniquely identies any node (xture) on a network.
There cannot be 2 xtures with the same IP address on the network!
Default IP Address -Preset IP address, you can set up only rst byte of IP address
(2 or 10) e.g. 002.019.052.086.
Custom IP Address - The option enables to set up all bytes of IP address.
Net Mask - The option enables to set up all bytes of Net Mask.
ArtNet Universe - Use
this item to set a Universe (0-255). The Universe is a single DMX
512 frame
of 512 channels.
MANet Settings - Use this menu to set parameters for MANet operation.
MANet Universe I/II - The value of this item can be set in range 1-256.
MANet Session ID - The value of this item can be set in range 1-32.
sACN Settings - Use this menu to set parameters for sACN operation.
sACN Universe - The value of this item can be set in range 1-32000.
sACN Priority - The value of this item can be set in range 0-255.
Klingnet Settings - Use this menu to enable or disable Klingnet protocol.
7.2 Tab "Information"
Fixture Times - The menu provides readouts of xture operation hours and air lters using hours.
Power On Time Hours - Select this menu to read the number of xture operation hours.
Total Hours -
The item shows the total number of the operation hours since the
Robin Spiider
has been fabricated.
Resetable Hours -
The item shows the number of the operation hours that the
Robin Spiider
has been powered on since the counter was last reset.
In order to reset this counter to 0, touch the text box next to the item "Resetable Hours:"
Air Filters - Regular cleaning of the air lters is very important for the xture´s life and performance.
Bild-up of dust, dirt and fog uid residues reduces the xture´s light output and cooling ability.
The two items of this menu help you to keep cleaning period of the air lters.
Alert period - Cleaning schedule for the xture depends on the operating environment.
It is therefore impossible to specify accurate cleaning interval. This item allows
you to change the cleaning interval of the air lters. This "alert" value is 300 hours and it
is set as default. Inspect the xture within its 300 hours of operation to see whether cleaning
is necessary. If cleaning is required, clean all air lters and change the value in this menu
on acceptable level. Min. level of alert period is 10 hours, max. is 300 hours.
Elapsed Time - The item allows you to read the time which remains to cleaning air lters.
The time period is set in the menu mentioned above.
Expired time period is signalled by a negative mark (-) at the time value and a warning icon
on the display.
Clean the lters and reset this menu item (by touching the text box next to the item
"Elapsed Time").
Fixture Temperatures - The menu is used to view temperatures of the xture´s inside.
LEDs temperatures - The menu shows temperature on the LEDs PCB .
Cur. - A current temperature of the LEDs PCB.
Max. - A maximum temperature of the LEDs PCB since the xture has
been fabricated.
Max. Res. - A maximum temperature of the LEDs PCB since the counter
was last reset.
In order to reset some counter to 0, touch desired text box under item "Max.Res."
Base Temperature - The menu shows temperature in the xture base (on the display PCB).
Current - A current temperature in the xture base.
Maximum NonRes. - A maximum temperature in the xture base since the xture has
been fabricated.
Page 21
21
Maximum Res. - A maximum temperature in the xture base since the counter
was last reset.
In order to reset this counter to 0, touch the text box next to the item "Maximum Res."
DMX Values - The menu is used to read DMX values of each channel received by the xture.
Wireless State - The menu serves for reading of the wireless operation status.
Unlink Wireless Adapter - The item serves for unlinking the xture from DMX transmitter.
Power Channel State - The menu item shows state of the Power/Special functions switches.
Software Version - Select this item to read the software version of the xture modules:
Display System - A display processor on the display board in the xture base
Module M - A pan/Tilt processors
Module DR - A LEDs driver
Module PX - Pixels + zooms control
Product IDs - The menu is used to read the MAC Address ,RDM UID and RDM Label.
View Logs - Use this menu to read xture´s data which have been recorded during xture operation. This
colected data allows easier troubleshooting.
Fixture Errors - Use this menu to read xture errors which have occured during xture operation.
Fixture States - Recorded following actions: Fixture On, Fixture O.
Fixture Position - Recorded installation positions of the xture:
Fixture Temperatures - Recorded temperatures which have exceeded dened levels.
Note: The log buer can contain 8000 records max. If the buer is full, old data will be overwritten.
7.3 Tab "Personality"
DMX Preset - Use the menu to select desired channel mode.
View Selected Preset - Use the menu to display channels included in the selected mode.
DMX Input- Use the menu to select mode of receiving DMX signal.
Wired - DMX signal is received by means of the standard DMX cable.
Wireless - DMX signal is received by means of the inbuilt wireless module.
Wireless In/XLR Out- the xture receives wireless DMX and sends the signal to its wired DMX output.
The xture behaves as " Wireless/Wired" adapter.
The options "Wired" and "Wireless" are also stated in DMX chart (channel Power/Special functions).
Pan/Tilt Settings - Use the menu set behaviour of both pan and tilt movements.
Pan Reverse - The item allows to invert pan movement.
Tilt Reverse - The item allows to invert tilt movement.
Pan/Tilt Feedback - The item allows to return the mowing head to the required pan/tilt position after
changing the position by an external force if this option is set on.
Note. Be careful, the Pan/Tilt Feedback should be permanent On, the option O is not suitable for standard
operation and the head of the xture can be damaged!
Pan/Tilt mode - Use this menu to set the mode of the pan/tilt movement
Time mode – The pan and tilt will move with dierent speeds and they will come at
Page 22
22
the same time to the end point of their tracks (pan and tilt use their optimal speeds).
Time of the pan/tilt movement (25.5 sec. max.) is set by the channel "Pan/Tilt speed, Pan/Tilt
time".
Speed Mode - Both Pan and tilt will move with the same speed as adjusted at the channel
"Pan/Tilt speed, Pan/Tilt time".
Pan/Tilt EMS - Built-in electronic motion stabilizer ensures precise position of the xture´s head during its
movement and also reducing its swinging when the truss shakes.
Microphone Sensitivity - Enter the menu if you want to adjust the microphone sensitivity from 1 (max.) to 20
(min.).
Blackout Settings - Use the menu if you need to close the light output under certain conditions which are
described below
Blackout DMC - Blackout during movement correction. Set this option On if you wish to close light
output during the time when the head goes to its correct position, which has been changed by an
external force.
Active Blackouts - Use this menu if you wish to close the light output during eect changes.
Pan/Tilt Moving - The menu item enables to close light output while the pan/tilt coordinates
are changing.
White Point 8000K - If the function is on, the CTC channel allows to set desired white in range of 8000K-2700K
(0 DMX=8000K, 255 DMX=2700K). Necessary condition is , that RGBW channels have to be full or set at the
same DMX values, e.g. 150.
If this function is o, the range of whites is not uniform and may be dierent for each xture.
Colour Mixing Mode - This item allows switching into RGBW or CMY mode. In the CMY mode, the white(8bit)/
white (16) bit channels are not active.
Tungsten Eect Sim. - This function simulates behaviour of a halogen lamp during dimming at calibrated whites
2700K, 3200K. You can select from various lamp wattage simulation: 750W, 1000W, 1200W, 2000W, 2500W.
Dimmer Curve - You can select desired dimmer curve: Linear or Square Law.
Init Eect Positions - Use the menu to set all eects to the desired positions at which they will stay after
switching the xture on without DMX signal connected.
Screen Settings - Use this menu to change the touch screen settings.
Display Intensity - The item allows to control the intensity of the screen (1-min., 10-max.).
Screen saver Delay - The item allows you to keep the screen on or to turn it o automatically after 1-10
minutes after last touch (or pressing any button on the control panel).
Touchscreen Lock - The item allows you to lock the screen after last touch (or pressing any button on the
control panel). The time delay can be set in range of 1-10 minutes.To unlock the screen, press the
[ENTER/Display On] button.
Recalibrate Touchscreen - The item starts calibration of the touchscreen. Follow the instructions on
the screen.
Display Orientation - The menu allows to change display orientation.
Normal - Standard display orientation if the xture is placed horizontally (e.g. on the ground).
Inverted - This function rotates menu 180 degrees from current orientation.
Auto - The option activates a gravitation sensor for automatic screen orientation.
Note: Auto option is set as default. You change the display orientation by touching the icon on the display,
an the option set in the "Display Orientation" menu is temporarily overriden.
Temperature unit - Use the menu item to change temperature unit from °C to °F.
Fan Mode - Use the menu to set the xture fans to max. power mode ("High") or to auto-control mode ("Auto").
Date & Time Settings - Use this menu to set current date and time for the xture log system (menu "View
Logs"). Set this menu item before rst xture operation.
Default Settings - The menu item allows to set all xture parameters to the default (factory) values.
Page 23
23
7.4 Tab "Manual Control"
Reset Functions - The menu allows to reset the xture either per function modules or all modules together.
Total System Reset - The item resets all function modules.
Pan/Tilt Reset - The item resets a pan and tilt movement.
Zoom Reset - The item resets zoom.
Flower E. Reset - The item resets Flower eect.
Manual Eect control - Use the menu to control all xture channels by means of the control panel.
7.5 Tab "Stand-alone"
Test Sequences -Use the menu to run a test/demo sequences without an external controller, which will show
you some possibilities of using Robin Spiider.
Dynamic Mode - This mode uses all Robin Spiider functions including pan/tilt movement and therefore
is good for a complete introduction of the xture.
Static Mode - This mode is suitable for projections on the wall, ceiling or ground without any pan/tilt movement.
Adjust the pan and tilt to desired positions and start test sequences by touching the green icon.
Music Trigger - Use the item to activate the sound control of the running program via the built-in microphone.
Preset Playback - This menu allows you to select the program which will be played in a loop after switching
the xture on (the option is commonly used in a stand-alone operation without an external controller).
None - The option disables “Presetting playback” function.
Test - The option starts the test sequences.
Prog. 1 - The option starts user program No. 1.
Prog. 2 - The option starts user program No. 2.
Prog. 3 - The option starts user program No. 3.
Play program - Use the menu to run desired program in a loop.
Play Program 1 - The option starts user program No.1.
Play Program 2 - The option starts user program No. 2.
Play Program 3 - The option starts user program No. 3.
Edit Program - Use the menu to create or to edit desired program. The Robin Spiider oers 3 free programs,
each up to 100 steps.
Edit Program 1 - The option allows to edit user program No.1.
Edit Program 2 - The option allows to edit user program No.2.
Edit Program 3 - The option allows to edit user program No.3
To edit program:
1. Touch the item which you want to edit (“Edit Program 1” - “Edit Program 3”).
2. Touch the item "Edit Program Steps".
3. Touch the item "Step 1".
4 From the list of eects touch desired eect and set its value. Browse throw the list by touching the [up arrow]
and [down arrow] and set all desired eects.
An item "Step Time" (value of 0-25.5 sec.) is the time during which eects last in the current step
5. Save adjusted eects to the current step by touching the [conrm] or save and copy them to the following
step by touching the [conrm+copy]. By touching the text box "Preview" next to the current program step you
can view created scene.
6. Repeat the steps 4 and 5 for next program steps.
7. After editing desired program steps, adjust the length of the program by touching the text boxes "Start Step"
and "End Step".
Meaning of the icons used in the "Edit Program" menu:
- moves down on the next page - saves adjusted values and leaves menu
- moves up on the previous page - saves values to the current step and copy them to the
Page 24
24
following prog. step
- leaves menu without saving values
7.6 Tab "Service"
Adjust DMX Values - The menu allows you to set all eects to desired positions before ne calibration of the
eects .
Calibrations - This menu enables ne calibration of xture eects and download default calibration values.
Calibrate Eects - The menu allows the ne adjustment of eects.
Pan- a pan position ne adjustment
Tilt - a tilt position ne adjustment
Calibration of the eects via the control board
1. Disconnect DMX controller from the xture and enter the "Calibrate Eects" menu.
2. Use the [up arrow] and [down arrow] to nd "Pan" and touch it to enter the ne eect adjustment screen.
3. Set desired value and save it by touching the [conrm].
4. Repeat steps 2 and 3 for next item
5. After calibrating all eects, touch the [conrm] to save all adjusted values and reset the xture.
Calibrate Colours - The menu serves for adjusting of LEDs saturation to achieve uniform white colours
Red - a red LEDs saturation ne adjustment
Green - a green LEDs saturation ne adjusment
Blue - a blue LEDs saturation ne adjustment
White - a white LEDs saturation ne adjustmentt
Calibration of white colours via the control board
1. Disconnect DMX controller from the xture , open shutter and dimmer and set the CTC channel
to DMX=64 (white 5600K), RGBW channels to 255 DMX and Zoom channel to 128 DMX.
2. Set the following items in the menu Personality:
White Point 8000K =On
Colour Mixing Mode=RGBW
3. Aim the light beam on the lux meter (e.g. Minolta CL-200A Chroma meter) which is placed at
min. distance of 3 m from the xture.
4. Enter the menu Calibrate Colours.
5. By means of the Red, green, Blue and White items adjust the 5600K colour temperature as exactly as
possible (∆u´v´= 0).
6. After adjusting 5600K colour temperature, touch the [conrm] to save all adjusted values and reset
the xture.
Calibration protocol:
Eect Mode 1 Mode 2 Mode 3 Mode 4
Pan-ne adjustment channel 49 channel 29 channel 33 channel 91
Tilt - ne adjustment channel 50 channel 30 channel 34 channel 92
Red - red saturation channel 51 channel 31 channel 35 channel 93
Green- green saturation channel 52 channel 32 channel 36 channel 94
Blue - blue saturation channel 53 channel 33 channel 37 channel 95
White - white saturation channel 54 channel 34 channel 38 channel 96
Calibrate Pan/Tilt EMS - This menu item allows calibration of the pan/tilt electronic motion stabilizer.
Important: during this calibration any external force must not inuence the xture and the surface at which
the xture stands (or truss if the xture hangs) has to be without movement, shake, strokes etc.
Load Default Calibrations - The item loads default (factory) calibration values.
Update software -
The menu item allows you to update software in the xture via either serial or USB port of PC.
The following are required in order to update software:
Page 25
25
- PC running Windows 10/8/7 or Linux
- DMX Software Uploader
- Flash cable RS232/DMX No.13050624 (if you want to use a serial port of PC)
- Robe Universal Interface (if you want to use an USB port of PC)
Note: Software update should execute a qualied person. If you lack qualication, do not attempt the
update yourself and ask for help your ROBE distributor.
DMX address, IP address, programs 1-3 and all items in the menu "Personality" will be set to their default
(factory) values.
To update software in the xture:
I. Installation of the DMX Software Uploader.
1. DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz.
2. Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.
3. Unpack the software.
II.Fixture software updating.
1.Determine which of your ports is available on your PC and connect it:
- with the DMX input of the xture if you using the ash cable RS232/DMX
- with the DMX output of the Robe Universal Interface if you using the USB cable.
Disconnect the xture from the other xtures in a DMX chain. Turn both the computer and
the xture on. Make sure the lamp is switched o (only if the xture involves a lamp).
2. Switch the xture to the updating mode by touching the "Updating Software " item
Note: If you do not want to continue in software update, you have to switch o and on the xture
to escape from this menu.
We recommend to cancel all running programs before starting the Software Uploader.
3. Run the Software Uploader program. Select desired COM and then click on the Connect button.
(Select COM if the serial port is used or Robe Universal Interface if the USB port is used).
If the connection is OK, click on the “Start Uploading button“ to start uploading. It will take several
minutes to perform software update.
If the option "Incremental Update" is not checked, all processors will be updated (including
processors with the same software version).
If you wish to update only later versions of processors, check the “Incremental Update box“.
Avoid interrupting the process. Update status is being displayed in the Info Box window.
When the update is nished, the line with the text “The xture is successfully updated“ will appear in
this window and the xture will reset with the new software.
Note: In the case of an interruption of the upload process (e.g. power cut), the xture keeps the updating mode
and you have to repeat the software update again.
8. RDM
This xture supports RDM operation. RDM (Remote Device Management) is a bi-directional communications
protocol for use in DMX512 control systems, it is the new open standard for DMX512 device conguration and
status monitoring.
The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely aecting
existing non-RDM equipment. By using a special „Start Code,“ and by complying with the timing specications
for DMX512, the RDM protocol allows a console or dedicated RDM controller to send commands to and receive
messages from specic moving lights.
RDM allows explicit commands to be sent to a device and responses to be received from it.
The list of commands for Robin Spiider is the following.
Parameter ID Discovery command SET command GET command
DISC_UNIQUE_BRANCH *
DISC_MUTE *
DISC_UN_MUTE *
DEVICE_INFO *
SUPPORTED_PARAMETERS *
SOFTWARE_VERSION_LABEL *
DMX_START_ADDRESS * *
IDENTIFY_DEVICE * *
DEVICE_MODEL_DESCRIPTION *
Page 26
26
MANUFACTURER_LABEL *
DEVICE_LABEL * *
SENSOR_DEFINITION *
SENSOR_VALUE *
DISPLAY_INVERT * *
DISPLAY_LEVEL * *
PAN_INVERT * *
TILT_INVERT * *
DEVICE_RESET *
DMX_PERSONALITY * *
DMX_PERSONALITY_DESCRIPTION *
STATUS_MESSAGES *
STATUS_ID_DESCRIPTION *
DEVICE_HOURS
2
*
ROBE_DMX_INPUT * *
ROBE_WIRELESS_UNLINK *
2
...Commands relative resetable values
Page 27
27
9. Error and information messages
Information icon
- Air Filters Cleaning
This icon signalizes that cleaning period of the air lters has elapsed
and you have to clear air lters and reset the menu item "Elapsed Time".
Errors
Error in the xture is signalled by the yellow warning icon at the bottom line of the screen:
Touch the warning icon or press the [ESCAPE] button to display error messages.
List of error and information messages:
Temper.Sensor Error
The message informs you that the communication betwen the head temperature sensor and the main processor
failed.
Tilt Error 1 (Tilt Error 2)
This message will appear after the reset of the xture if the head´s magnetic-indexing circuit malfunctions
(sensor failed or magnet is missing) or the stepping motor is defective or its driving IC on the PCB. The head
is not located in the default position after the reset.
Pan Error 1 (Pan Error 2)
This message will appear after the reset of the xture if the yoke´s magnetic-indexing circuit malfunctions (sensor failed or magnet is missing) or the stepping motor is defective or its driving IC on the PCB. The yoke is not
located in the default position after the reset of the xture.
Zoom Error 1 (Zoom Error 2 )
The messages will appear after the reset of the zoom module if the zoom module is not located in the default
position.
Rod Error
The messages will appear after the reset of the ower eect if the rod is not in the default position.
EEprom Error
Hardware error of the EEprom.
Recharge The battery
The battery on the display board needs to be charged. Let the xture on for cca 6 hrs.
Battery faulty. Replace it.
The battery on the display board is exhausted and should be replaced immediately.
Pan/Tilt EMS Cal. Error
The EMS system is not calibrated.
Pan/Tilt EMS Error
Control electronics cannot communicate with the EMS system.
Clean Air Filters
The message informs that the item "Elapsed Time" in the "Fixture Information" menu is at 0 value. Clean air
lters and reset this counter.
Page 28
28
10. Technical Specications
Electrical
Power supply:.........................electronic auto-ranging
Input voltage range:............... supply 100-240V, 50-60Hz
Fuse:.......................................T 8 A
Max. power consumption .......600W at 230V ( power factor= 0.98; I=2.7A)
Optic
Light source: 19 RGBW LED multichips
RGBW or CMY colour mixing
19 controllable LED multichips (pixels)
Min. LED life expectancy: 20.000 hours (at full load of LEDs)
Virtual colour wheel
66 preset colours
CTC in range of 2700K-8000K
Halogen lamp eect at whites 2700K and 3200K
Rainbow eect with in both directions with variable speed
Zoom
Linear motorized zoom
Min. beam angle: 4° (1/2 beam)
Max. beam angle: 50°(1/10 beam)
Eect
Flower eect rotating in both directions
10 Flower eect macros
Strobe
Strobe eect with variable speed (0.3 - 20Hz)
Dimmer
Smooth dimmer from 0 - 100 %
Control
Graphic touch screen for xture setting and addressing
Gravitation sensor for auto screen positioning
Battery backup of the touch screen
Readout xture and LED module usage, receiving DMX values, temperatures, etc
Built-in analyzer for easy fault nding, error messages
Built-in demo sequences
Individual pixel control of each LED
Stand-alone operation
3 user editable programs, each up to 100 steps
Supported protocols: USITT DMX 512, RDM, ArtNet, MANet, MANet2, sACN, Kling-Net
Support of RDM (Remote Device Management)
10 DMX modes (49, 27, 33, 90, 27,47, 91,110,104,123 control channels)
Wireless DMX/RDM module (only for Wireles DMX version)
Compliance with USITT DMX-512 (1986 & 1990) and 512-A
Full DMX delity and frame integrity
Auto sensing of DMX frame rate and frame size
<5ms DMX latency
Operational frequency range of 2402-2480 MHz
Producer: LumenRadio
Page 29
29
Pan/Tilt
Pan movement range 540°
Tilt movement range 230°
Continual pan/tilt rotation
16 bit movement resolution
Pan/Tilt electronic motion stabilizer
Automatic Pan/Tilt position correction
Remotely controllable speed of pan/tilt movement for easy programming
Movement control: tracking and vector
Pan/tilt-lock mechanism
Connection
DMX data in/out: Locking 3-pin and 5-pin XLR
AC power IN: Neutrik TrueOne NAC3MPX
Ethernet IN/Out: RJ45
Max. number of xtures in Ethernet IN/Out line
5
Rigging
Mounting points: 2 pairs of 1/4-turn locks
Mounting horizontally or vertically via two Omega brackets
Temperatures
Maximum ambient temperature : 45° C
Maximum housing temperature : 75° C
Minimum distances
Min. distance from ammable surfaces: 0.5 m
Min. distance to lighted object: 1 m
Total heat dissipation
Maximum: 2040 BTU/hr
Ingress protection
IP2x
Accessories
Omega Adaptor CL-regular 2 pcs (P/N 10980033)
1 x power cable
Weight (net)
13.25 kg
Page 30
30
Dimensions (mm)
Optional accessories
Upgrade kit CRMX Univerzal 260 (P/N 9903 0100)
EggCrate for Spiider (P/N10980317)
Page 31
31
11. Maintenance and cleaning
It is absolutely essential that the xture is kept clean and that dust, dirt and smoke-uid residues must not build
up on or within the xture. Otherwise, the xture‘s light-output will be signicantly reduced. Regular cleaning will
not only ensure the maximum light-output, but will also allow the xture to function reliably throughout its life.
DANGER !
Disconnect from the mains before starting any
maintenance and cleaning work
The outer side of the front optical module should be cleaned monthly by means of a vacuum cleaner as dust
reducing the light-output very quickly. The cooling fans should be cleaned at least twice a year.
The interior of the xture should be cleaned at least annually using a vacuum cleaner or an air-jet.
Important! Check the air lter periodically and clean before they become
clogged!
Periodically clean air lter placed in the xture´s base. The air lter cover is fastened by means of magnets.
Use a vacuum cleaner, compressed air or you can wash them and put back dry.
After replacing the air lters, reset the elapsed time counter in the menu "Information" (Information--->Air Filters---> Elapsed Time).
Replacing the fuse.
Before replacing the fuse, unplug mains lead.
1) Remove the fuse holder on the rear panel of the base with a tting screwdriver from the housing
(anti-clockwise).
2) Remove the old fuse from the fuse holder.
3) Install the new fuse in the fuse holder (only the same type and rating).
4) Replace the fuseholder in the housing and x it.
Page 32
32
11.1 Removing the optical module
The following instructions are intended for service purposes only
.
To remove the optical module
1. Disconnect the xture from mains.
2. Loosen the four fastening screws (2) on each side
of the head covers (1) to remove the covers.
3. Loosen the four fastening screws (4) on back cover
of the head (3)
4. Unscrew the securing screw (5) from the
guide-pin. Its position is shown on the picture (the fan
connecting PCB (6) has to be on the right from the
securing screw (5)).
If you do not have access to the securing screw, push
the optical module (7) towards the fans. Do not touch
the plastic lenses bare hands.
DO NOT FORGET TO UNSCREW THIS SECURING
SCREW (5)!
5. Carefully take the optical module (7) out of the
guide-tubes (11) and motors (10).
To insert the optical module back
1. Connect the xture to mains and after xture reset
go to tab Manual Control, select item Zoom and set
it at 255 DMX.
2. Put the optical module (7) on the LED module
(12) in such a way that three guide-pins (8) aim into
guide-tubes (11) and three lead screws (9) aim into
motors (10).
3. Hold the optical module in this position and slowly
change the item Zoom from 255 DMX to 0 DMX.
Motors "draw" the optical module to the LED module
(12).
DO NOT TRY TO INSERT THE OPTICAL
MODULE BY A FORCE.
4. Run the Zoom Reset from tab Manual Control
or disconnect/connect the xture to mains.
5. Disconnect the xture from mains.
6. Screw the securing screw (5) back to the guide-pin.
DO NOT FORGET TO SCREW THIS SECURING
SCREW (5)!
7. Screw covers on the xture head.
Page 33
33
11.2 Disposing of the product
To preserve the environment please dispose or recycle this product at the end of its life according to the local
regulations and codes.
12. ChangeLog
This section summarizes all types of changes in the user manual.
Version of the
manual
Date of issue Description of changes
1.1 16/12/2016 DMX protocol ver. 1.3 (add 6 DMX modes)
1.2 24/01/2017 Added Eggcrate installation
1.3 10/02/2017 DMX protocol ver. 1.4 (Pattern crossfade channel added)
1.4 27/02/2017 DMX protocol ver.1.5
1.5 24/03/2017 DMX protocol ver.1.6
Page 34
34
13. Photometric diagrams
Page 35
35
March 24, 2017
Copyright © 2016-2017 Robe Lighting - All rights reserved
All Specications subject to change without notice
Page 36
DMX protocol
1 2 3 4
1 1 1 1
Pan (8 bit)
0 - 255 Pan movement by 540° (128=default) proportional
2 2 2 2
Pan Fine (16 bit)
0 - 255 Fine control of pan movement (0=default) proportional
3 3 3 3
Tilt (8 bit)
0 - 255 Tilt movement by 230° (128=default) proportional
4 4 4 4
Tilt fine (16 bit)
0 - 255 Fine control of tilt movement (0=default) proportional
5 5 5 5
Pan/Tilt speed , Pan/Tilt time
0 Max. speed -tracking mode (0=default) step
Pan/Tilt speed
1 - 255 Speed from max. to min. (vector mode) proportional
Pan/Tilt time
1 - 255 Time from 0.1 s to 25.5 sec. proportional
6 6 6 6
Power/Special functions
0 -9 Reserved (0=default)
To activate following functions, stop in DMX value for at least 3 s
and shutter must be closed at least 3 sec. („Shutter,Strobe”
channel 53/27/31/31 must be at range: 0-31 DMX). Corresponding
menu items are temporarily overriden).
10-14
DMX input: Wired DMX
step
15-19
DMX input: Wireless DMX *
step
20-24
Graphic display ON
step
25-29
Graphic display OFF
step
30-34
RGBW colour mixing mode
step
35-39
CMY colour mixing mode
step
40-44
Pan/Tilt speed mode
step
45 - 49
Pan/Tilt time mode
step
50 -54
Blackout while pan/tilt moving
step
55 -59
Disabled blackout while pan/tilt moving
step
60 - 64
Dimmer curve-square law
step
65 - 69
Dimmer curve-linear
step
70 - 74
Fans mode: Auto
step
75 - 79
Fans mode: High
step
80-84
White point 8000K ON
step
85-89
White point 8000K OFF
step
90 -109
Reserved
110-114
Kling-Net On
step
115-119
Kling-Net Off
step
120-129
Reserved
To activate following functions, stop in DMX value for at least 3
seconds.
130 - 139
Fixture reset (except pan/tilt)
140 - 149
Pan/Tilt reset
step
150 - 159
Zoom reset
step
Robin SPIIDER - DMX protocol
Version: 1.6 (10 modes) Mode 1 - 3-zones, Mode 2-Basic, Mode 3 -Advanced, Mode 4 -Full RGBW
Mode/channel
DMX
Value
Function
Type of
control
Page 1
Page 37
DMX protocol
160 - 169
Flower effect reset
step
170-171
Tungsten effect simulation (750W) On **
step
172-173
Tungsten effect simulation (1000W) On **
step
174-175
Tungsten effect simulation (1200W) On **
step
176-177
Tungsten effect simulation (2000W) On **
step
178-179
Tungsten effect simulation (2500W) On **
step
180-181
Tungsten effect simulation Off
step
182 - 199
Reserved
200 - 209
Total fixture reset
step
210 - 255
Reserved
7 7 7 7
Virtual colour wheel
0 No function (0=default) step
1-2
Filter 4 (Medium Bastard Amber)
step
3-4
Filter 25 (Sunset Red)
step
5-6
Filter 19 (Fire)
step
7-8
Filter 26 (Bright Red)
step
9-10
Filter 58 (Lavender)
step
11-12
Filter 68 (Sky Blue)
step
13-14
Filter 36 (Medium Pink)
step
15-16
Filter 89 (Moss Green)
step
17-18
Filter 88 (Lime Green)
step
19-20
Filter 90 (Dark Yellow Green)
step
21-22
Filter 49 (Medium Purple)
step
23-24
Filter 52 (Light Lavender)
step
25-26
Filter 102 (Light Amber)
step
27-28
Filter 103 (Straw)
step
29-30
Filter 140 (Summer Blue)
step
31-32
Filter 124 (Dark Green)
step
33-34
Filter 106 (Primary Red)
step
35-36
Filter 111 (Dark Pink)
step
37-38
Filter 115 (Peacock Blue)
step
39-40
Filter 126 (Mauve)
step
41-42
Filter 117 (Steel Blue)
step
43-44
Filter 118 (Light Blue)
step
45-46
Filter 122 (Fern Green)
step
47-48
Filter 182 (Light Red)
step
49-50
Filter 121 (Filter Green)
step
51-52
Filter 128 (Bright Pink)
step
53-54
Filter 131 (Marine Blue)
step
55-56
Filter 132 (Medium Blue)
step
57-58
Filter 134 (Golden Amber)
step
59-60
Filter 135 (Deep Golden Amber)
step
61-62
Filter 136 (Pale Lavender)
step
63-64
Filter 137 (Special Lavender)
step
65-66
Filter 138 (Pale Green)
step
67-68
Filter 798 (Chrysalis Pink)
step
69-70
Filter 141 (Bright Blue)
step
71-72
Filter 147 (Apricot)
step
73-74
Filter 148 (Bright Rose)
step
75-76
Filter 152 (Pale Gold)
step
Page 2
Page 38
DMX protocol
77-78
Filter 154 (Pale Rose)
step
79-80
Filter 157 (Pink)
step
81-82
Filter 143 (Pale Navy Blue)
step
83-84
Filter 162 (Bastard Amber)
step
85-86
Filter 164 (Flame Red)
step
87-88
Filter 165 (Daylight Blue)
step
89-90
Filter 169 (Lilac Tint)
step
91-92
Filter 170 (Deep Lavender)
step
93-94
Filter 172 (Lagoon Blue)
step
95-96
Filter 194 (Surprise Pink)
step
97-98
Filter 180 (Dark Lavender)
step
99-100
Filter 181 (Congo Blue)
step
101-102
Filter 197 (Alice Blue)
step
103-104
Filter 201 (Full C.T. Blue)
step
105-106
Filter 202 (Half C.T. Blue)
step
107-108
Filter 203 (Quarter C.T. Blue)
step
109-110
Filter 204 (Full C.T. Orange)
step
111-112
Filter 219 (Fluorescent Green)
step
113-114
Filter 206 (Quarter C.T. Orange)
step
115-116
Filter 247 (Filter Minus Green)
step
117-118
Filter 248 (Half Minus Green)
step
119-120
Filter 281 (Three Quarter C.T. Blue)
step
121-122
Filter 285 (Three Quarter C.T. Orange)
step
123-124
Filter 352 (Glacier Blue)
step
125-126
Filter 353 (Lighter Blue)
step
127-128
Filter 507 (Madge)
step
129-130
Filter 778 (Millennium Gold)
step
131-132
Filter 793 (Vanity Fair)
step
133-235
Raw DMX
proportional
236-245 Rainbow effect (with fade time) from slow-> fast proportional
246-255 Rainbow effect (without fade time) from slow-> fast proportional
* 8 8 8
Red/Cyan (8 bit)- all pixels***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
* * 9 9
Red/Cyan (16bit)- all pixels***
0 - 255 Colour saturation control - fine (255=default) proportional
* 9 10 10
Green/Magenta (8 bit) - all pixels ***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
* * 11 11
Green/Magenta (16bit) - all pixels***
0 - 255 Colour saturation control - fine (255=default) proportional
* 10 12 12
Blue/Yellow (8 bit) - all pixels ***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
* * 13 13
Blue/ Yellow (16bit) -all pixels***
0 - 255 Colour saturation control - fine (255=default) proportional
* 11 14 14
White (8 bit) - all pixels
If RGBW mode is selected:
0-255 Colour saturation control - coarse 0-100% (255=default) proportional
If CMY mode is selected:
0 - 255 No function
* * 15 15
White (16 bit) - all pixels
0 - 255 Colour saturation control - fine (255=default) proportional
Page 3
Page 39
DMX protocol
8 * * *
Red/Cyan (8 bit) - zone 1***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
9 * * *
Red/Cyan (16bit)- zone 1***
0 - 255 Colour saturation control - fine (255=default) proportional
10 * * *
Green/Magenta (8 bit) - zone 1***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
11 * * *
Green/Magenta (16bit)- zone 1***
0 - 255 Colour saturation control - fine (255=default) proportional
12 * * *
Blue/Yellow (8 bit) - zone 1***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
13 * * *
Blue/Yellow (16bit)- zone 1***
0 - 255 Colour saturation control - fine (255=default) proportional
14 * * *
White (8 bit) - zone 1
If RGBW mode is selected:
0-255 Colour saturation control - coarse 0-100% (255=default) proportional
If CMY mode is selected:
0 - 255 No function
15 * * *
White (16 bit) - zone 1
0 - 255 Colour saturation control - fine (255=default) proportional
16 * * *
Red/Cyan (8 bit) - zone 2***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
17 * * *
Red/Cyan (16bit)- zone 2***
0 - 255 Colour saturation control - fine (255=default) proportional
18 * * *
Green/Magenta (8 bit) - zone 2***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
19 * * *
Green/Magenta (16bit)- zone 2***
0 - 255 Colour saturation control - fine (255=default) proportional
20 * * *
Blue/Yellow (8 bit) - zone 2***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
21 * * *
Blue/Yellow (16bit)- zone 2***
0 - 255 Colour saturation control - fine (255=default) proportional
22 * * *
White (8 bit) - zone 2
If RGBW mode is selected:
0-255 Colour saturation control - coarse 0-100% (255=default) proportional
If CMY mode is selected:
0 - 255 No function
23 * * *
White (16 bit) - zone 2
0 - 255 Colour saturation control - fine (255=default) proportional
24 * * *
Red/Cyan (8 bit) - zone 3***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
25 * * *
Red/Cyan (16bit)- zone 3***
0 - 255 Colour saturation control - fine (255=default) proportional
26 * * *
Green/Magenta (8 bit) - zone 3***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
27 * * *
Green/Magenta (16bit)- zone 3***
0 - 255 Colour saturation control - fine (255=default) proportional
28 * * *
Blue/Yellow (8 bit) - zone 3***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
29 * * *
Blue/Yellow (16bit)- zone 3***
0 - 255 Colour saturation control - fine (255=default) proportional
Page 4
Page 40
DMX protocol
30 * * *
White (8 bit) - zone 3
If RGBW mode is selected:
0-255 Colour saturation control - coarse 0-100% (255=default) proportional
If CMY mode is selected:
0 - 255 No function
31 * * *
White (16 bit) - zone 3
0 - 255 Colour saturation control - fine (255=default) proportional
32 12 16 16
CTC
If function "White Point 8000K" is ON
0-255
Col. temperature correction from 8000K to 2700K -for whites only
proportional
(0=8000K, 64=5600K, 128=4200K, 192=3200K, 255=2700K)
To get colour temperatures stated above, RGBW channels have to
be set at the same value (e.g. 255DMX) or RGB=0 and White
channel > 0 DMX (0=default)
(To activate Tungsten effect at 2700K and 3200K , set DMX value at
"Power/Special functions" channel)
If function "White Point 8000K" is OFF
0-255 Colour temperature correction from cool col. to warm colours proportional
33 13 17 17
Colour Mix control
The channel defines relation between color channels
IF Flower effect is active, its colour channels always have priority!
Global = Global Colours (RGBW, Virtual Colour Wheel)
Pixel = Pixel Colours (RGB individual pixels or Kling-Net)
0-9 Global colours (Global has priority)
10-19 Maximum mode (highest values have priority) step
20-29 Minimum mode (lowest values have priority) step
30-39 Multiply mode (multiply Global and Pixel) step
40-49 Addition mode (Global + Pixel) /45=default/ step
50-59 Subtraction mode (Global – Pixel) step
60-69 Inverted Subtraction mode (Pixel – Global) step
70-79 Coloured background step
80-127 Raw DMX proportional
128 Global colours only (Global has priority) step
129-254 Crossfade (crossfade between Global and Pixel) proportional
255 Pixel colours (Pixel has priority) step
34 14 18 18
Pixel effects
0-2 No function (0=default)
3-4 Effect 1 step
5-6 Effect 2 step
: : :
181-182 Effect 90 step
183-255 Raw DMX proportional
35 15 19 19
Pixel effects speed
0-127 Speed from from min. to max. (0=default) proportional
128-255 Speed from max. to min. (opposite direction) proportional
36 16 20 20
Pixel effects fade
0 Without fade time (0=default) step
1-255 Fade time from min. to max. proportional
37 17 21 21
Flower Effect
0 Open position-without Flower Effect (0=default) step
Page 5
Page 41
DMX protocol
1 - 127 Flower Effect forwards rotation from fast to slow proportional
128 Flower Effect -without rotation step
129-255 Backwards rotation from slow to fast proportional
38 18 22 22
Flower Effect - Red (8 bit)
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
39 19 23 23
Flower Effect - Green (8 bit)
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
40 20 24 24
Flower effect - Blue (8 bit)
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
41 21 25 25
Flower Effect - White (8 bit)
0-255 Colour saturation control - coarse 0-100% (255=default) proportional
42 22 26 26
Flower Effect - colour macros
(Flower Effect channel has to be set > 0 DMX)
step
0
Open position - without macros (0=default)
(Flower effect colour macros have priority to RGBW colours/Virtual colour
wheel,Flower effect colours )
1-2
Flower Effect colour macro 1
step
3-4
Flower Effect colour macro 2
step
5-6
Flower Effect colour macro 3
step
:
119-120
Flower Effect colour macro 60
step
121-255
Raw DMX
proportional
43 23 27 27
Flower Effect - Shutter/ strobe
0 - 31 Shutter closed step
32 - 63 Shutter open (32=default) step
64 - 95 Strobe-effect from slow to fast proportional
96 - 127 Shutter open step
128 - 143 Opening pulse in sequences from slow to fast proportional
144 - 159 Closing pulse in sequences from fast to slow proportional
160 - 191 Shutter open step
192 - 223 Random strobe-effect from slow to fast proportional
224 - 255 Shutter open step
44 24 28 28
Flower Effect - Dimmer intensity (8 bit)
0 - 255 Dimmer intensity from 0% to 100% (0=default) proportional
45 25 29 29
Zoom
0-255 Zoom from max. to min.beam angle (128=default) proportional
46 * 30 30
Zoom - fine
0-255 Fine zooming (0=default) proportional
47 26 31 31
Shutter/ strobe
0 - 31 Shutter closed step
32 - 63 Shutter open (32=default) step
64 - 95 Strobe-effect from slow to fast proportional
96 - 127 Shutter open step
128 - 143 Opening pulse in sequences from slow to fast proportional
144 - 159 Closing pulse in sequences from fast to slow proportional
160 - 191 Shutter open step
192 - 223 Random strobe-effect from slow to fast proportional
224 - 255 Shutter open step
48 27 32 32
Dimmer intensity (8 bit)
0 - 255 Dimmer intensity from 0% to 100% (0=default) proportional
Page 6
Page 42
DMX protocol
49 * 33 33
Dimmer intensity - fine (16 bit)
0 - 255 Fine dimming (0=default) proportional
* * * 34
Red pixel 1
0-255 Red LED saturation control 0-100% (0=default) proportional
* * * 35
Green pixel 1
0-255 Green LED saturation control 0-100% (0=default) proportional
* * * 36
Blue pixel 1
0-255 Blue LED saturation control 0-100% (0=default) proportional
:
* * * 88
Red pixel 19
0-255 Red LED saturation control 0-100% (0=default) proportional
* * * 89
Green pixel 19
0-255 Green LED saturation control 0-100% (0=default) proportional
* * * 90
Blue pixel 19
0-255 Blue LED saturation control 0-100% (0=default) proportional
* function is active only 10 seconds after switching the fixture on
** In the Tungsten effect simulation the Dimmer channel imitates behaviour of the halogen lamp during dimming
*** Select RGB or CMY mixing mode on channel "Power/Special functions"
Copyright © 2016-2017 Robe Lighting s.r.o. - All rights reserved
All Specifications subject to change without notice
Page 7
Page 43
DMX protocol
5 6 7 8 9 10
1 1 1 1 1 1
Pan (8 bit)
0 - 255 Pan movement by 540° (128=default) proportional
2 2 2 2 2 2
Pan Fine (16 bit)
0 - 255 Fine control of pan movement (0=default) proportional
3 3 3 3 3 3
Tilt (8 bit)
0 - 255 Tilt movement by 270° (128=default) proportional
4 4 4 4 4 4
Tilt fine (16 bit)
0 - 255 Fine control of tilt movement (0=default) proportional
5 5 5 5 5 5
Pan/Tilt speed , Pan/Tilt time
0 Max. speed -tracking mode (0=default) step
Pan/Tilt speed
1 - 255 Speed from max. to min. (vector mode) proportional
Pan/Tilt time
1 - 255 Time from 0.1 s to 25.5 sec. proportional
6 6 6 6 6 6
Power/Special functions
0 -9 Reserved (0=default)
To activate following functions, stop in DMX value for at least 3 s
and shutter must be closed at least 3 sec. („Master Shutter/Strobe”
channel 26/44/32/32/44/44 must be at range: 0-31 DMX).
Corresponding menu items are temporarily overriden).
10-14
DMX input: Wired DMX
step
15-19
DMX input: Wireless DMX *
step
* function is active only10 seconds after switching the fixture on
20-24
Graphic display ON
step
25-29
Graphic display OFF
step
30-34
RGBW colour mixing mode
step
35-39
CMY colour mixing mode
step
40-44 Pan/Tilt speed mode step
45-49 Pan/Tilt time mode step
50-54 Blackout while pan/tilt moving step
55-59 Disabled blackout while pan/tilt moving step
60-64 Dimmer curve-square law step
65-69 Dimmer curve-linear step
70-74
Fans mode: Auto
step
75-79
Fans mode: High
step
80-84
White point 8000K ON
step
85-89
White point 8000K OFF
step
90-109
Reserved
110-114
Kling-Net On
step
115-119
Kling-Net Off
step
120-129 Reserved
To activate following functions, stop in DMX value for at least 3
seconds.
130 - 139 Fixture reset (except pan/tilt)
140 - 149 Pan/Tilt reset step
Robin SPIIDER - DMX protocol
Version: 1.6 (10 modes) Mode 5-Wash, Mode 6-Pattern, Mode 7-Pixel RGB, Mode 8-Pixel RGBW, Mode 9-Pattern full RGB, Mode 10-Pattern full RGBW
Mode/channel
DMX
Value
Function
Type of
control
Page 1
Page 44
DMX protocol
5 6 7 8 9 10
Mode/channel
DMX
Value
Function
Type of
control
150 - 159 Zoom reset step
160 - 169
Flower effect reset
step
170-171
Tungsten effect simulation (750W) On **
step
172-173
Tungsten effect simulation (1000W) On **
step
174-175
Tungsten effect simulation (1200W) On **
step
176-177
Tungsten effect simulation (2000W) On **
step
178-179
Tungsten effect simulation (2500W) On **
step
180-181
Tungsten effect simulation Off
step
182 - 199
Reserved
200 - 209
Total fixture reset
step
210 - 255
Reserved
7 7 7 7 7 7
Background - Virtual colour wheel
0 No function (0=default) step
1-2
Filter 4 (Medium Bastard Amber)
step
3-4
Filter 25 (Sunset Red)
step
5-6
Filter 19 (Fire)
step
7-8
Filter 26 (Bright Red)
step
9-10
Filter 58 (Lavender)
step
11-12
Filter 68 (Sky Blue)
step
13-14
Filter 36 (Medium Pink)
step
15-16
Filter 89 (Moss Green)
step
17-18
Filter 88 (Lime Green)
step
19-20
Filter 90 (Dark Yellow Green)
step
21-22
Filter 49 (Medium Purple)
step
23-24
Filter 52 (Light Lavender)
step
25-26
Filter 102 (Light Amber)
step
27-28
Filter 103 (Straw)
step
29-30
Filter 140 (Summer Blue)
step
31-32
Filter 124 (Dark Green)
step
33-34
Filter 106 (Primary Red)
step
35-36
Filter 111 (Dark Pink)
step
37-38
Filter 115 (Peacock Blue)
step
39-40
Filter 126 (Mauve)
step
41-42
Filter 117 (Steel Blue)
step
43-44
Filter 118 (Light Blue)
step
45-46
Filter 122 (Fern Green)
step
47-48
Filter 182 (Light Red)
step
49-50
Filter 121 (Filter Green)
step
51-52
Filter 128 (Bright Pink)
step
53-54
Filter 131 (Marine Blue)
step
55-56
Filter 132 (Medium Blue)
step
57-58
Filter 134 (Golden Amber)
step
59-60
Filter 135 (Deep Golden Amber)
step
61-62
Filter 136 (Pale Lavender)
step
63-64
Filter 137 (Special Lavender)
step
65-66
Filter 138 (Pale Green)
step
67-68
Filter 798 (Chrysalis Pink)
step
69-70
Filter 141 (Bright Blue)
step
Page 2
Page 45
DMX protocol
5 6 7 8 9 10
Mode/channel
DMX
Value
Function
Type of
control
71-72
Filter 147 (Apricot)
step
73-74
Filter 148 (Bright Rose)
step
75-76
Filter 152 (Pale Gold)
step
77-78
Filter 154 (Pale Rose)
step
79-80
Filter 157 (Pink)
step
81-82
Filter 143 (Pale Navy Blue)
step
83-84
Filter 162 (Bastard Amber)
step
85-86
Filter 164 (Flame Red)
step
87-88
Filter 165 (Daylight Blue)
step
89-90
Filter 169 (Lilac Tint)
step
91-92
Filter 170 (Deep Lavender)
step
93-94
Filter 172 (Lagoon Blue)
step
95-96
Filter 194 (Surprise Pink)
step
97-98
Filter 180 (Dark Lavender)
step
99-100
Filter 181 (Congo Blue)
step
101-102
Filter 197 (Alice Blue)
step
103-104
Filter 201 (Full C.T. Blue)
step
105-106
Filter 202 (Half C.T. Blue)
step
107-108
Filter 203 (Quarter C.T. Blue)
step
109-110
Filter 204 (Full C.T. Orange)
step
111-112
Filter 219 (Fluorescent Green)
step
113-114
Filter 206 (Quarter C.T. Orange)
step
115-116
Filter 247 (Filter Minus Green)
step
117-118
Filter 248 (Half Minus Green)
step
119-120
Filter 281 (Three Quarter C.T. Blue)
step
121-122
Filter 285 (Three Quarter C.T. Orange)
step
123-124
Filter 352 (Glacier Blue)
step
125-126
Filter 353 (Lighter Blue)
step
127-128
Filter 507 (Madge)
step
129-130
Filter 778 (Millennium Gold)
step
131-132
Filter 793 (Vanity Fair)
step
133-235
Raw DMX
proportional
236-245 Rainbow effect (with fade time) from slow-> fast proportional
246-255 Rainbow effect (without fade time) from slow-> fast proportional
8 8 8 8 8 8
Background - Red/Cyan (8 bit)***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
* 9 9 9 9 9
Background - Red/Cyan (16bit)***
0 - 255 Colour saturation control - fine (255=default) proportional
9 10 10 10 10 10
Background - Green/Magenta (8 bit)***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
* 11 11 11 11 11
Background - Green/Magenta (16bit) ***
0 - 255 Colour saturation control - fine (255=default) proportional
10 12 12 12 12 12
Background - Blue/Yellow (8 bit)***
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
* 13 13 13 13 13
Background - Blue/ Yellow (16bit)***
0 - 255 Colour saturation control - fine (255=default) proportional
11 14 14 14 14 14
Background - White (8 bit) - all pixels
If RGBW mode is selected:
Page 3
Page 46
DMX protocol
5 6 7 8 9 10
Mode/channel
DMX
Value
Function
Type of
control
0-255 Colour saturation control - coarse 0-100% (255=default) proportional
If CMY mode is selected:
0 - 255 No function
* 15 15 15 15 15
Background - White (16 bit) - all pixels
0 - 255 Colour saturation control - fine (255=default) proportional
12 16 16 16 16 16
Background - CTC
If function "White Point 8000K" is ON
0-255 Col. temperature correction from 8000K to 2700K -for whites only proportional
(0=8000K, 64=5600K, 128=4200K, 192=3200K, 255=2700K)
To get colour temperatures stated above, RGBW channels have to
be set at the same value (e.g. 255DMX) or RGB=0 and White
channel > 0 DMX (0=default)
(To activate Tungsten effect at 2700K and 3200K , set DMX value at
"Power/Special functions" channel)
If function "White Point 8000K" is OFF
0-255 Colour temperature correction from cool col. to warm colour proportional
13 17 17 17 17 17
Background - Shutter/ strobe
0 - 31 Shutter closed step
32 - 63 Shutter open (32=default) step
64 - 95 Strobe effect from slow to fast proportional
96 - 127 Shutter open step
128 - 143 Opening pulse in sequences from slow to fast proportional
144 - 159 Closing pulse in sequences from fast to slow proportional
160 - 191 Shutter open step
192 - 223 Random strobe effect from slow to fast proportional
224 - 255 Shutter open step
14 18 18 18 18 18
Background - Dimmer intensity (8 bit)
0 - 255 Dimmer intensity from 0% to 100% (255=default) proportional
* 19 19 19 19 19
Background Dimmer intensity - fine (16 bit)
0 - 255 Fine dimming (255=default) proportional
15 20 20 20 20 20
Background - Active zone
0-2 All pixels (0=default)
3-4 Ring 1 (Middle pixel) step
5-6 Ring 2 step
7-8 Ring 3 step
9-10 Ring 1+ Ring 2 step
11-12 Ring 1+ Ring 3 step
13-14 Ring 2 + Ring 3 step
15-16 Sector 1 step
17-18 Sector 2 step
19-20 Sector 3 step
21-22 Sector 4 step
23-24 Sector 5 step
25-26 Sector 6 step
27-28 Sector 1+4 step
29-30 Sector 1+4+Ring 1 step
31-32 Sector 2+5 step
33-34 Sector 2+5+Ring 1 step
35-36 Sector 3+6 step
Page 4
Page 47
DMX protocol
5 6 7 8 9 10
Mode/channel
DMX
Value
Function
Type of
control
37-38 Sector 3+6+Ring 1 step
39-40 Sector 1+3+5 step
41-42 Sector 1+3+5+Ring 1 step
43-44 Sector 2+4+6 step
45-46 Sector 2+4+6+Ring 1 step
47-48 Sector 1+2+3 step
49-50 Sector 2+3+4 step
51-52 Sector 3+4+5 step
53-54 Sector 4+5+6 step
55-56 Sector 5+6+1 step
57-58 sector 6+1+2 step
59-255 Raw DMX proportional
16 21 21 21 21 21
Colour Mix control
The channel defines relation between color channels
IF Flower effect is active, its colour channels always have priority!
Global = Global Colours (Background RGBW, Background Virtual
Colour Wheel, Background CTC)
Pixel = Pixel Colours (RGB individual pixels or Kling-Net)
0-9 Global colours (Global has priority)
10-19 Maximum mode (highest values have priority) step
20-29 Minimum mode (lowest values have priority) step
30-39 Multiply mode (multiply Global and Pixel) step
40-49 Addition mode (Global + Pixel) /45=default/ step
50-59 Subtraction mode (Global – Pixel) step
60-69 Inverted Subtraction mode (Pixel – Global) step
70-79 Coloured background step
80-127 Raw DMX proportional
128 Global colours only (Global has priority) step
129-254 Crossfade (crossfade between Global and Pixel) proportional
255 Pixel colours (Pixel has priority) step
17 22 22 22 22 22
Flower Effect
0 Open position-without Flower Effect (0=default) step
1 - 127 Flower Effect forwards rotation from fast to slow proportional
128 Flower Effect -without rotation step
129-255 Backwards rotation from slow to fast proportional
18 23 23 23 23 23
Flower Effect - Red/Cyan (8 bit)
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
19 24 24 24 24 24
Flower Effect - Green/Magenta (8 bit)
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
20 25 25 25 25 25
Flower effect - Blue/Yellow (8 bit)
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
21 26 26 26 26 26
Flower Effect - White (8 bit)
0-255 Colour saturation control - coarse 0-100% (255=default) proportional
22 27 27 27 27 27
Flower Effect - colour macros
(Flower Effect channel has to be set > 0 DMX) step
0 Open position - without macros (0=default)
(Flower effect colour macros have priority to RGBW colours/Virtual colour
wheel,Flower effect colours, channels Flower effect-Shutter/strobe and
Flower effect-dimmer has to be open )
Page 5
Page 48
DMX protocol
5 6 7 8 9 10
Mode/channel
DMX
Value
Function
Type of
control
1-2 Flower Effect colour macro 1 step
3-4 Flower Effect colour macro 2 step
5-6 Flower Effect colour macro 3 step
:
119-120 Flower Effect colour macro 60 step
121-255 Raw DMX proportional
23 28 28 28 28 28
Flower Effect - Shutter/ strobe
0 - 31 Shutter closed step
32 - 63 Shutter open (32=default) step
64 - 95 Strobe-effect from slow to fast proportional
96 - 127 Shutter open step
128 - 143 Opening pulse in sequences from slow to fast proportional
144 - 159 Closing pulse in sequences from fast to slow proportional
160 - 191 Shutter open step
192 - 223 Random strobe-effect from slow to fast proportional
224 - 255 Shutter open step
24 29 29 29 29 29
Flower Effect - Dimmer intensity (8 bit)
0 - 255 Dimmer intensity from 0% to 100% (255=default) proportional
25 30 30 30 30 30
Zoom
0-255 Zoom from max. to min.beam angle (128=default) proportional
* 31 31 31 31 31
Zoom - fine
0-255 Fine zooming (0=default) proportional
* 32 * * 32 32
Pattern selection
0-2 No pattern (0=default)
3-4 Pattern 1 step
5-6 Pattern 2 step
7-8 Pattern 3 step
9-10 Pattern 4 step
11-12 Pattern 5 step
13-14 Pattern 6 step
15-16 Pattern 7 step
17-18 Pattern 8 step
19-20 Pattern 9 step
21-22 Pattern 10 step
23-24 Pattern 11 step
25-255 RAW DMX proportional
* 33 * * 33 33
Pattern - Repeat (Size)
0-2 Variant 1 (0=default) step
3-4 Variant 2 step
5-6 Variant 3 step
7-8 Variant 4 step
9-10 Variant 5 step
11-12 Variant 6 step
13-14 Variant 7 step
15-16 Variant 8 step
17-18 Variant 9 step
19-20 Variant 10 step
21-22 Variant 11 step
Page 6
Page 49
DMX protocol
5 6 7 8 9 10
Mode/channel
DMX
Value
Function
Type of
control
23-255 Raw DMX proportional
* 34 * * 34 34
Pattern - Rotation
0 No rotation (0=default) step
1-127 Pattern indexing proportional
128-190 Forwards rotation from fast to slow proportional
191-192 Pause - without rotation step
193-255 Backwards rotation from slow to fast proportional
* 35 * * 35 35
Pattern - Fade
0 Snap (0=default) step
1-255 Fade from min. to max. proportional
* 36 * * 36 36
Pattern -Transition
0 No fade (0=default) step
1 100ms step
:
255 4 sec step
* 37 * * 37 37
Pattern - Crossfade
0 Background step
1-255 Crossfade between Background and Pattern 0-100% (255=default) proportional
* 38 * * 38 38
Pattern - Red (8-bit)
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
* 39 * * 39 39
Pattern - Green (8-bit)
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
* 40 * * 40 40
Pattern - Blue (8-bit)
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
* 41 * * 41 41
Pattern - White (8-bit)
0 - 255 Colour saturation control - coarse 0-100% (255=default) proportional
* 42 * * 42 42
Pattern - Colour macro
0-2 No macro (0=default) step
Macros 1-15 allow control of colour change speed from min. to max.
3-8 Macro 1 proportional
9-14 Macro 2 proportional
15-20 Macro 3 proportional
21-26 Macro 4 proportional
27-32 Macro 5 proportional
33-38 Macro 6 proportional
39-44 Macro 7 proportional
45-50 Macro 8 proportional
51-56 Macro 9 proportional
57-62 Macro 10 proportional
63-68 Macro 11 proportional
69-74 Macro 12 proportional
75-80 Macro 13 proportional
81-86 Macro 14 proportional
87-92 Macro 15 proportional
93-98 Macro 16 step
99-104 Macro 17 step
105-110 Macro 18 step
111-255 Raw DMX proportional
Page 7
Page 50
DMX protocol
5 6 7 8 9 10
Mode/channel
DMX
Value
Function
Type of
control
* 43 * * 43 43
Pattern - Shutter/ strobe
0 - 31 Shutter closed step
32 - 63 Shutter open (32=default) step
64 - 95 Strobe effect from slow to fast proportional
96 - 127 Shutter open step
128 - 143 Opening pulse in sequences from slow to fast proportional
144 - 159 Closing pulse in sequences from fast to slow proportional
160 - 191 Shutter open step
192 - 223 Random strobe effect from slow to fast proportional
224 - 255 Shutter open step
* 44 * * 44 44
Pattern - Dimmer intensity (8 bit)
0 - 255 Dimmer intensity from 0% to 100% (255=default) proportional
26 45 32 32 45 45
Master Shutter/ strobe
0 - 31 Shutter closed step
32 - 63 Shutter open (32=default) step
64 - 95 Strobe effect from slow to fast proportional
96 - 127 Shutter open step
128 - 143 Opening pulse in sequences from slow to fast proportional
144 - 159 Closing pulse in sequences from fast to slow proportional
160 - 191 Shutter open step
192 - 223 Random strobe effect from slow to fast proportional
224 - 255 Shutter open step
27 46 33 33 46 46
Master Dimmer intensity (8 bit)
0 - 255 Dimmer intensity from 0% to 100% (0=default) proportional
* 47 34 34 47 47
Master Dimmer intensity - fine (16 bit)
0 - 255 Fine dimming (0=default) proportional
* * 35 35 48 48
Red pixel 1
0-255 Red LED saturation control 0-100% (0=default) proportional
* * 36 36 49 49
Green pixel 1
0-255 Green LED saturation control 0-100% (0=default) proportional
* * 37 37 50 50
Blue pixel 1
0-255 Blue LED saturation control 0-100% (0=default) proportional
* * * 38 * 51
White pixel 1
0-255 White LED saturation control 0-100% (0=default) proportional
:
* * 89 104 102 120
Red pixel 19
0-255 Red LED saturation control 0-100% (0=default) proportional
* * 90 105 103 121
Green pixel 19
0-255 Green LED saturation control 0-100% (0=default) proportional
* * 91 106 104 122
Blue pixel 19
0-255 Blue LED saturation control 0-100% (0=default) proportional
* * * 110 * 123
White pixel 19
0-255 White LED saturation control 0-100% (0=default) proportional
* function is active only 10 seconds after switching the fixture on
** In the Tungsten effect simulation the Dimmer channel imitates behaviour of the halogen lamp during dimming
*** Select RGB or CMY mixing mode on channel "Power/Special functions"
Copyright © 2016 -2017 Robe Lighting s.r.o. - All rights reserved
Page 8
Page 51
Colour name
Red
(DMX)
Green
(DMX)
Blue
(DMX)
White
(DMX)
Filter 4 (Medium Bastard Amber)
255
1180109
Filter 25 (Sunset Red)
255500
3
Filter 19 (Fire)
255130
0
Filter 26 (Bright Red)
25500
0
Filter 58 (Lavender)
117097
110
Filter 68 (Sky Blue)
42
195
100
0
Filter 36 (Medium Pink)
255748
24
Filter 89 (Moss Green)
69
24503
Filter 88 (Lime Green)
187
22600
Filter 90 (Dark Yellow Green)
0
25510
Filter 49 (Medium Purple)
255027
0
Filter 52 (Light Lavender)
2278614
134
Filter 102 (Light Amber)
233
16400
Filter 103 (Straw)
207
137033
Filter 140 (Summer Blue)
0
1617218
Filter 124 (Dark Green)
29
255012
Filter 106 (Primary Red)
24211
0
Filter 111 (Dark Pink)
2556711
49
Filter 115 (Peacock Blue)
0
2552841
Filter 126 (Mauve)
255039
0
Filter 117 (Steel Blue)
163
25514161
Filter 118 (Light Blue)
0
2556134
Filter 122 (Fern Green)
98
25532
Filter 182 (Light Green)
255162
0
Filter 121 (Filter Green)
165
25500
Filter 128 (Bright Pink)
255013
32
Filter 131 (Marine Blue)
73
2452730
Filter 132 (Medium Blue)
0
193
113
0
Filter 134 (Golden Amber)
191830
0
Filter 135 (Deep Golden Amber)
255520
0
Filter 136 (Pale Lavender)
1649629
54
Filter 137 (Special Lavender)
1306063
102
Filter 138 (Pale Green)
226
255051
Filter 798 (Chrysalis Pink)
49098
14
Filter 141 (Bright Blue)
8
176620
Filter 147 (Apricot)
215
104015
Filter 148 (Bright Rose)
25530
37
Filter 152 (Pale Gold)
202
115039
Filter 154 (Pale Rose)
214
107048
Filter 157 (Pink)
255565
48
Filter 143 (Pale Navy Blue)
0
19372148
Filter 162 (Bastard Amber)
223
153641
Filter 164 (Flame Red)
255270
4
Filter 165 (Daylight Blue)
23
2368781
Filter 169 (Lilac Tint)
206
1230110
Filter 170 (Deep Lavender)
235
1234133
Filter 172 (Lagoon Blue)
0
255540
Robin Spiider - colours on Virtual Colour Wheel
1
Page 52
Colour name
Red
(DMX)
Green
(DMX)
Blue
(DMX)
White
(DMX)
Filter 194 (Surprise Pink)
110021
255
Filter 180 (Dark Lavender)
13643181
89
Filter 181 (Congo Blue)
370255
0
Filter 197 (Alice Blue)
107
220
129
0
Filter 201 (Full C.T. Blue)
179
2555734
Filter 202 (Half C.T. Blue)
217
255373
Filter 203 (Quarter C.T. Blue)
236
255303
Filter 204 (Full C.T. Orange)
230
12537
Filter 219 (Fluorescent Green)
99
1481650
Filter 206 (Quarter C.T. Orange)
204
140057
Filter 247 (Filter Minus Green)
255810
193
Filter 248 (Half Minus Green)
255
1440137
Filter 281 (Three Quarter C.T. Blue)
225
25572160
Filter 285 (Three Quarter C.T. Orange)
199
124017
Filter 352 (Glacier Blue)
0
1616590
Filter 353 (Lighter Blue)
0
1153797
Filter 507 (Madge)
255310
0
Filter 778 (Millennium Gold)
255650
0
Filter 793 (Vanity Fair)
255013
16
2
Loading...