Robic SC-606 User Manual

Page 1 of 8
Rev 02 05/04/05

SC-606 Instructions

SC-606

Thank you for buying the Robic SC-606. Your purchase brings you a world class timer with a vast array of
advanced timekeeping functions.

Please take a few moments to review this operating guide, so that you may become familiar with the SC­606’s many capabilities and how you can best access them for your maximum benefit.

PART I
PUSHBUTTON and INDICATOR LOCATION

The following illustration details the location of pushbuttons and indicators for setting and operating the
SC-606.

Pushbutton “B”
LAP •SPLIT/RESET

Pushbutton “A”
START/STOP

Indicators:
UP, DOWN, AVG, MAX, SET

Pushbutton “D”
AVG/MAXIMUM
Alarm Time Display

Pushbutton “F”
MEMORY RECALL/SET

Indicators:
CHRONO, LAP/SPL, RUN, STOP, RCL, ♠, (((•)))

Pushbutton “C”
ADVANCE/RELEASE, Alarm/Chime On/Off

Pushbutton “E”
MODE/NEXT

The indicators in this illustration will appear only when a particular mode or function is activated by
pressing a pushbutton.

Once you are familiar with the SC-606’s operation, you will be ready to enjoy its many functions. The
starting point for any operation is the NORMAL TIME mode. You may sequence through the modes by
pressing “E”.

NORMAL TIME

¾ Time of Day in Hours, Minutes and Seconds
¾ Calendar with Day, Month and Date
¾ AM/PM or 24 Hour Time Options
¾ Daily Alarm and Hourly Chime

CHRONOGRAPH (Stopwatch)

Three (3) Timing Options
(1) Lap Time Chronograph

Page 2 of 8

dicator

Rev 02 05/04/05
(2) Split (accumulated) Time Chronograph, or

(3) Dual Lap/Split Time Chronograph

Each option offers these functions:

¾ 1/100 Second Resolution to 24 Hours
¾ Recall of the previous 30 Time Readings
¾ Automatic Lap/Split Counter . . . up to 999 Readings
¾ Memory Recall Can be Presented in Either Ascending (1,2,3. . .) or Descending ( . . . 3,2,1) Order
¾ Fastest and Average Lap Time Display

COUNTDOWN TIMER

¾ Multi-Mode, Countdown Timer select from: Countdown Stop, Countdown Repeat or Countdown,

Count-Up

¾ 1/10 second resolution of time remaining
¾ Set any time to countdown from one second to 16 hours
¾ Loud audible completion alarm
¾ Time-Out (pause) operation

Battery: Lithium type CR-2025 or equivalent

PART II
NORMAL TIME OPERATION

Press “E” until NORMAL TIME appears.

Calendar

Time of Day

Time of Day is presented in Hours, Minutes and Seconds in the lower row. Calendar is presented in Day,
Month and Date, in the upper row.

Alarm Time Display
While in NORMAL TIME, press “D” to display the Alarm Time. “AL” will appear in the upper row of the
display to indicate the Alarm Time.

Alarm
In

Alarm Time

Time of day

Setting NORMAL TIME and ALARM TIME

While in NORMAL TIME mode, press and hold “F” for 2-3 seconds. “SET” indicator appears. Alarm
hours will begin flashing. Advance Alarm Hours by pressing or holding “C”. After setting Alarm Hours,
Press “E”. Alarm Minutes will appear flashing. Advance by pressing or holding “C”.

Page 3 of 8
Rev 02 05/04/05

Repeat the setting process for Seconds >>>> Hours >>>> Minutes >>>> Month >>>> Date >>>> Day of
the Week >>>> 12/24 Hour Option >>>> and back to Alarm Hours.

Pressing “F” at any time, will automatically exit the setting procedure. “SET” indicator disappears.

Time of Day and Alarm Time will both be presented in the AM/PM or 24 Hour format chosen. “A” or “P”
will appear in the AM/PM format.

Using the Daily Alarm and Hourly Chime

The Alarm can be armed (set to go off) to sound once per day. The Alarm symbol ((((•)))) will appear
when the alarm is armed.

The Hourly Chime can be armed to sound one (1) beep at the top of each hour. The Chime indicator (♠ )
will appear when the chime is armed.

While your SC-606 is in NORMAL TIME mode, press “C” to arm, or disarm your alarm and chime. The
sequence is:

(1) Alarm ON, Chime OFF
(2) Chime ON, Alarm OFF
(3) Alarm ON, Chime ON
(4) Alarm OFF, Chime OFF

When armed, the alarm will sound when the Alarm Time coincides with Time of Day. You may silence
the alarm by pressing any pushbutton.

PART III
CHRONOGRAPH MODE (Stopwatch)

The SC-606’s chronograph is a digital stopwatch with 1/100 second resolution, which will present timing
in any of three (3) different options.

From NORMAL TIME, press “E” once to enter the CHRONOGRAPH mode. Chrono indicator “CHR”
and all zeros should appear. If the display does not show all zeros, reset the chrono by:
If RUN appears, press “A” to STOP and “B” to RESET.
If STOP appears, simply press “B” to RESET to all zeros.

“LAP” Chrono will display the

Interval of time from your previous readings. Each time a reading is taken,

the timer begins from zero.

“SPLIT” Chrono will display the
taken, the timer shows the

Accumulation of time from the start of the event. Each time a reading is

Total amount of time accrued.

“LAP/SPLIT” Chrono will display the Lap Time in the upper row and the Split Time in the lower row of
the display.

General Operation

Select from the LAP, SPLIT or LAP/SPLIT options by pressing “C”.