Roberts 3/16"" Crown Electric Stapler, 10-600 Owner's Manual

3/16" Crown Electric Stapler

OWNER’S MANUAL

Agrafeuse Èlectrique pour

Agrafes Crown 3/16"

MANUEL D’UTILISATION

Grapadora Électrica para

Grapas Corona de 3/16"

MANUAL DE OPERACIÓN

10-600

PLEASE READ THIS
MANUAL CAREFULLY
BEFORE USING TOOL.

WARNING

It is important to read and
understand these
instructions fully before
using the tool. Failure to
follow these instructions
may result in electric shock,
fire and/or serious
personal injury.

SAVE THESE INSTRUCTIONS.

General Safety Instructions:

Work Area

Keep your work area clean and well lit.
Accidents may result from cluttered
benches and dark areas. Do not operate
power tool in explosive atmospheres,
such as in the presence of flammable
liquids, gases or heavy thick dust.
Power tools create sparks, which may
ignite such substances. Keep
bystanders, children and visitors away
while operating tool. Such distractions
can cause loss of control.

Electrical Safety

• Don’t expose power tool to rain or
wet conditions. Water can increase
the risk of electric shock.

• Never abuse power cord or carry the
tool by the cord or yank the cord to
disconnect it from a receptacle. Keep
cord away from heat, oil and sharp
edges at all times.

Personal Safety

• Guard against electric shock. Prevent
body contact with grounded surfaces
such as pipes, radiators, ranges, etc.

•

KEEP AWAY FROM CHILDREN AND
VISITORS.

Do not let visitors come in

contact with tool or extension cord.

• Store idle tools in a dry and
locked-up place; high and out
of the reach of children.

• Stay alert when operating tool at all
times. Use common sense and
car

efully watch what you ar

e doing.

Do not operate tool if you ar

e tir

ed or
under the influence of drugs, alcohol
or medication.

• Ensure proper dress by NOT wearing
clothing or jewelry that may get
caught in moving parts. Wear rubber
gloves and non-skid footwear,
especially when working outdoors.
Protect and contain long hair with
proper coverings.

•

ALWAYS WEAR EYE PROTECTION

such as OSHA required “Z87” safety
glasses. Also consider the use of
earplugs, hard hats or
other equipment specific
to the job for adequate
personal protection.

Tool Use and Care

• Do not force tool when

using. Tool is more
efficient and safe when
used at the rate for which
it was intended.

• Use the right tool. Do not use tool for

a purpose not intended.

• Never abuse power cord.

• Keep tools clean to maintain efficient

and safe performance. Follow
instructions for lubricating and
changing accessories. Inspect tool
cords periodically to check for
damage. If damage occurs, have the
tool repaired by an authorized facility.
Keep handles dry, clean and free from
oil/grease.

• When operating tool, DO NOT

overreach. Keep proper footing and
balance at all times.

• Disconnect tool when not in use,

before servicing and when
changing accessories.

• Avoid unintentional starting of the

tool by making sure switch is OFF
and tool is unplugged before
carrying/transporting tool.

• Use only extension cords intended for

outdoor use when operating
tool outdoors.

• Before using tool, check for damaged

parts or ensure all parts are operating
correctly and will perform as
designed. Any damaged parts
should be r

epaired or replaced by

an authorized facility.

•

When ser

vicing, use only identical

r

eplacement par

ts ordered from an
authorized service facility. DO NOT
attempt to modify or create.

accessories not recommended for
the tool. Alterations, modifications or
misuse could result in serious
personal injury.

• Never point driving tool with
operational fasteners at yourself or
any other person.

Tool Specific
Safety Instructions:

• NOTICE: NEVER POINT THE

STAPLER AT ANOTHER PERSON OR
TOWARD ANYTHING YOU DO NOT
WANT TO STAPLE. SEVERE BODILY
INJURY CAN OCCUR. ALWAYS HAVE
THE STAPLER HEAD SECURELY
SEATED ON OBJECTS TO BE
STAPLED BEFORE PULLING THE
TRIGGER. UNPLUG WHEN NOT
IN USE.

• Use only 20 gauge 3/16" crown

staples in 1/4", 5/16", 3/8", 1/2" and
9/16" lengths. We recommend that
only Duo-Fast

®

staples be used. Use
of accessories that are not designed
for the tool may cause personal
injury and damage to the tool.

• Before connecting tool to a power
source (outlet, receptacle, etc.), be
sure that the power supply is of the
same voltage as specified on the
tool. Use of a higher voltage then
specified could result in a serious
injury to the user and damage to the
tool. Use of a lower voltage could
also cause injury or damage.

• Ensure tool is grounded while in use
to protect yourself from electric
shock. Use only 3-wire extension
cords that have 3-prong grounding
type plugs and 3-pole receptacles
that accepts the tool’s plug. Replace
or repair damaged cords.

Safety Instructions:

• Only hold plastic handle when tool
is in use. DO NOT touch tool’s
metal parts.

• Do not use tool on a hard surface
such as rock or concrete. Personal
injury or damage to the tool
may result.

• When using tool in high elevations,
ensure proper footing and that no
one is below the work area that could
possibly be injured.

• Improper use of an extension cord
may result in the risk of fire and/or
electric shock. If an extension cord
must be used, always ensure the
prongs are the same number, size
and shape to fit inside the plug and
that the extension cord is properly
wired, in good condition and the wire
size is large enough to carry the full
amp rating of the tool. Use only 12
gauge or 14 gauge extension cords
with this tool. An undersized cord will
cause a drop in tool voltage resulting
in loss of power and overheating. If in
doubt, use the next heaviest gauge.
The smaller the gauge number, the
heavier the cord.

• Take special caution when tacking
thin material. Fasteners may
penetrate through such material and
cause possible harm to anything or
anyone in the immediate area.

• Never connect tool to a DC
power source.

• During operation, the stapler head
may be warm to the touch. This is
normal. However, if the tool begins to
feel hot, slow down tacking speed. If
the unit continues to be hot,
discontinue use until it cools.

• Do not drive fasteners on top of other
fasteners or with tool at too steep of
an angle. Fasteners may ricochet and
injure someone.

• Do not drive fasteners too close to
the edge of the work materials. The
work piece is likely to split and the
fasteners could fly free or ricochet
and injur

e someone.

Disconnect the power supply.

Depress the magazine latch.

Pull back on the magazine cover

.

Insert a strip of fasteners into

the magazine. Make sure the

staple’s crown is resting

on the magazine.

Push the magazine cover

for

war

d until the latch catches.

Operating Instructions

AVOID BLANK SHOTS THAT COULD

SHORTEN THE TOOL’S COMPONENT LIFE.

Loading Staples

Extension Cords

Use only 12 or 14 gauge extension cords with the 10-600 Electric
Stapler. For maximum performance, use the shortest length
extension cord possible.

CAUTION: ALWAYS DISCONNECT THE POWER SUPPLY TO THE TOOL
BEFORE ADJUSTING, CLEARING JAMS, SERVICING, RELOCATING AND
DURING NON-OPERATION.

NOTE: USE ONLY DUO-FAST

®

BRAND STAPLES TO MINIMIZE POSSIBILITY

OF JAMMING.

Clearing Fastener Jams inside the Magazine

1.Disconnect the power supply.

2. Press down the latch and pull back on the magazine.

3. Remove jammed fasteners using needle nose or standard pliers.

4. Reinsert staples in magazine.

5. Push the magazine cover forward until the latch catches.

6. Reconnect power supply.

Clearing Fastener Jammed in the Discharge Area

1.Disconnect the power supply.

2. Remove jammed fasteners using needle nose or standard pliers.

3. If fastener cannot be reached from discharge area, refer to
“Clearing Fastener Jams Inside the Magazine” above.

4. Reinsert staples in magazine.

5. Push the magazine cover forward until the latch catches.

6. Reconnect power supply.

General Maintenance

1. Keep all screws tight. Loose screws could result in unsafe operations
and breakage of parts.

2. Occasionally wipe the inside of the magazine and the "nose" with
light oil. Make sure dirt and debris is removed from the trigger area
magazine, and the staple "chute".

3. Wipe tool clean daily and inspect for wear. Use non-flammable
cleaning solutions only if necessary. Never soak tool, for such
solutions may damage tool parts and electrical components.

4. Keep fastener discharge area clean at all times. Any residues could
cause jamming.

SERVICE: Return your stapler to your Roberts dealer or distributor for
servicing of any pr

oblem.

Maintenance & Inspection

ROBERTS 10-600

3/16" CROWN ELECTRIC STAPLER

1

20 Volt Wiring Diagram

REPLACEMENT PARTS LIST

Power
Supply

Coil

White

Green

Ground

Clip

Red

Red

Red

Trigger
Switch

Line
Cord
Plug

Black

Blue

SKU# Description

Contents of Kit

Part # Description

10-600-01 Cap Assembly 1 Hex Bolt (4)

2 Washers (4)
3 Cap Casting

10-600-02 Driver Assembly 4 Retainer

5 Drive Plunger
6 Roll Pin
7 Driver Blade

10-600-03 Solenoid Assembly 8 Retaining Washer

9

Retur

n Spring

10

Sleeve

11 Coil Assembly w/ Lead Wires

10-600-04 Head Assembly 12 Head Casting

13 Bolts (2)
14 Nose Bumper
15 Lock Nuts

REPLACEMENT PARTS LIST (continued)

SKU # Description

Contents of Kit

Part # Description

10-600-05 Trigger Assembly 16 Switch Plunger

17 Switch Housing
18 Switch
19 Plunger
20 Trigger
21 Trigger Pin

10-600-06 Handle Assembly 22 Screws (2)

23 Handle (Right)
24 Nut
25 Grip Insert (Right)
34 Handle (Left)
35 Bolts
36 Grip Insert (Left)
37 Bolt

10-600-07 Fuse Holder Assembly 26 Fuse Holder

27 Screws (2)

10-600-08 Cord Assembly 28 Power Cord - 14 gauge

29 Connector Jacket
10-600-09 Power Supply 30 Power Supply
10-600-10 Nose Casting 38 Nose Casting
10-600-11 Magazine Assembly 39 Plate

40 Pin

42 Bolt

43 Magazine Support

44 Rack

45 Spring

46 Pusher

47 Magazine Base
10-600-12 Staple “Pusher” & Spring 45 Spring

46 Staple Pusher
10-600-14 Spare Fuses Set of 3 Fuses

Technical Specifications

• Carpet installation

• Carpeting stairs

• Underlayment and carpet pad

• Upholstering

• Light wood assembly

• Display & sign work

• Light trim & molding

• Pre-finished paneling

• Lattice

• Plywood assembly

Note: Use only fastener sizes that fit description above. Using

non-specified fasteners may damage tool and/or cause injury. Only use
tool for intended purpose. Only fire fasteners into work surfaces that are
never too hard to penetrate.

Model: 10-600

Current: 120 V, AC 60Hz single phase

Drive Solonoid: 15 Amps, 1,500 Watts

Size: 9"L x 6.875"H x 2.75"W

Weight: 7.6 lbs.

Fastener: 20 gauge 3/16" crown staples

(Recommended DUO-FAST

®

Brand)

Fastener Capacity: 85

Fastener Length: 3/16", 1/4", 5/16", 3/8", 1/2", 9/16"

Uses:

For Customer and Technical Service

Call Toll Free 1.866.435.8665