Robert Juliat ARAMIS 1013+, ARAMIS 1013+ B, ARAMIS 1013+ BS, ARAMIS 1013+ M, ARAMIS 1013+ BSM Technical Manual

1013+, 1013+ B, 1013+ BS, 1013+ M & 1013+ BSM

HMI 2500W HOT RESTRIKE FOLLOWSPOTS /

PROJECTEURS DE POURSUITE HMI 2500W

REAMORCAGE A CHAUD

V2c

VALIDATION: 02/03/11

DN30750100-D

ARAMIS+

Robert Juliat S.A.S. Route de Beaumont, F 60530 Fresnoy-en-Thelle - phone : [phone] - fax : [phone] - [e-mail]
Robert Juliat U.S.A. 48 Capital Drive, Wallingford, CT 06492 - phone : [phone] - fax : [phone] - [e-mail]

TECHNICAL FILE /

DOSSIER TECHNIQUE :

ii

NOTES

iii

You have in your possession a ROBERT JULIAT HMI followspot. We would like to congratulate you
on your choice.

The performance of the followspot depends on the care you'll give to its maintenance. We advise
you to read this manual and then keep it for reference.

Do not hesitate to come up with suggestions ; it's thanks to you that our products will continue
to improve.

Thank you.

ROBERT JULIAT

Vous venez de prendre possession de votre nouveau projecteur de poursuite et nous vous
remercions de votre choix.
Le résultat que vous en obtiendrez dépendra pour beaucoup du soin que vous apporterez
à son entretien, aussi nous vous conseillons de lire ces quelques pages qui ont été écrites à
votre intention et de les conserver en cas de nécessité.

Ne manquez pas de nous faire part de vos idées ou suggestions ; c’est grâce à vous que le
produit pourra évoluer.

Merci de votre attention.

ROBERT JULIAT

iv

CONTENTS

A TECHNICAL DATA

User's instructions ......................................................................................................A - 1

The identification plates .......................................................................................... A - 3

Connection for 1013+ / BS .......................................................................................A - 5

Connection for 1013+ B ........................................................................................... A - 7

Connection for 1013+ M / BSM ..............................................................................A - 9

Putting the lamp into place ..................................................................................A - 11

Admissible Lamp .....................................................................................................A - 13

Network use for 1013+ B ........................................................................................A - 15

Using the DMX lamp control unit for 1013+ B ..................................................A - 17

Connection for 1013+ B .........................................................................................A - 19

B MAINTENANCE

Condenser, mirror and spark-gap ......................................................................... B - 1

Non-functioning diagnosis for 1013+ .................................................................. B - 3

Electrical diagram - lamp housing for 1013+ / B / BS ....................................... B - 5

C SPARE PARTS LIST

Lamp housing and lens tube ................................................................................... C - 1

6 way colour changer unit .......................................................................................C - 2

Lens tube inner parts for 1013+ / M .......................................................................C - 3

Lens tube inner parts for 1013+ B / BS / BSM ....................................................... C - 4

"Black-out" iris cassette ............................................................................................. C - 5

Lamp housing, socket holder and lamp ...............................................................C - 6

Aspheric lens and mirror holder detail ..................................................................C - 7

Zoom handle, gobo and gobo changer & soft glass holder ............................ C - 8

Section:

Section:

Section:

Section A - 1

TECHNICAL FILE

2500W HMI FOLLOWSPOT

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

USER’S INSTRUCTIONS

GENERAL INSTRUCTIONS

1. Not for residential use.

2. Only quali ed technicians are permitted to service these  xtures.

3. In addition to the instructions indicated on this page, you must
adhere to the relevant health and safety requirements of the
appropriate EU Directives.

4. This  xture is in compliance with section 17: Lighting appliance
for theatre stages, television, cinema and photograph studios.
Standards NF EN 60598-1 and NF EN 60598-2-17.

5. This  xture is rated as IP20, and is for indoor use only.

FIXTURE

6. Warning: high voltage ignition. Disconnect from the mains before

any servicing.

7. Make sure the  xture is correctly mounted on an appropriate
support.

8. The protection screens, lenses or U.V.  lters must be replaced if there
is any visual damage which might reduce their performance, for
example, by cracks or deep scratches.

9. When hung or  own the  xture must be secured by another hanging
accessory (such as a safety cable or bond) that is of suitable length.

10. The safety bond or cable must be securely attached at the back of
the  xture. It must be as short as possible or rolled up as necessary
to ensure the  xture does not travel any distance should it be
dislodged.

11. Movable accessories (barn doors, HMI shutters, spill rings etc.) must
also be secured with a suitable safety cable or bond at the front of
the  xture.

12. Take into account the weight of both the  xture and the accessories
when choosing the strength of the attachment point and the safety
cable or bond.

13. Do not open the lighting  x ture when the lamp is on.

14. Both the lamp and lamp housing heat up when powered. Wait until
the  xture is cold before servicing.

15. Do not tamper with the design of the  xture nor any of its safety
features.

16. Tighten the electrical mains cable connections regularly. Replace
mains cable with an identical one if damaged.

17. Use only with correct power supply.

Ventilation

18. Keep well away from  ammable material.

19. Do not use outside. Do not cover. Do not permit the  xture to get
wet.

20. To avoid overheating, do not obstruct air vents.

21. If the  xture has fans, make sure they are working correctly. If fans
are not working, turn the  xture o immediately and service as
necessary.

Lamp

22. Use only fully enclosed in the  xture.

23. Never look at the lamp directly.

24. Warning : U.V. rays : Protect your eyes.

25. Check that the lamp voltage corresponds to the mains voltage used.
Do not use a lamp with power that is an incorrect type or voltage to
the one that is indicated on the lamp housing or packaging.

26. The lamp must be replaced if it has been damaged or deformed by
the heat.

27. Use only when bulb is in place.

Cleaning

28. Do not touch the lamp or the mirror with your  ngers.

29. Keep optical parts (lens, lamps,…) clean with alcohol.

30. Regularly remove dust from the mirror with a soft and clean rag.

31. If the  x ture has  lters they must be cleaned frequently.

POWER SUPPLY

32. Disconnect from the mains before any servicing.

33. Mains connection only. Do not connect to an "electronic output"
(dimmer, static relay...).

34. Do not use outside. Do not cover.

35. The power supply has circuit breakers, which should always be kept
accessible.

36. There is no maximum distance between the lighting unit and the
power supply.

37. Check the mains voltage.

PLEASE NOTE

These products have been built to conform to European standards
relating to professional lighting equipment. Any modi cation made to
our products will void the manufacturers' warranty

Please read carefully all the instructions before operating the appliance.

Danger

The discharge lamp used emits short-wave ultraviolet
radiation which is harmful to skin and eyes.

Section A - 3

TECHNICAL FILE

2500W HMI FOLLOWSPOT

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

- The identi cation plate situated on the 2500W HMI followspot.

THE IDENTIFICATION PLATES.

Units :

- Dimensions = metre (m) millimetre (mm). - Frequency = Hertz (Hz).

- Weight = kilogram (kg). - Power = Watt (W).

- Intensity = Ampere (A) milliampere (mA). - Temperature = Degree Celsius (°C).

- Voltage = Volt (V).

1 User's instructions, read the previous page

attentively.

2 The brand mark, manufacturer's name and
origin of the product.
3 Control N° : Year & WeeK.
4 European conformity.
5 Net weight without accessories.
6 - Lighting unit's reference & technical characteristics.

- PSU = The type of power supply unit necessary.

- P = Maximum power authorised.

- AL = Max. lamp intensity.

- UL = Max. voltage at the lamp terminal.

- IP 20 = indoor use ONLY.

- t a = surrounding temperature.

- t max = External maximum temperature
of the unit.
7 Restrictive position use : front view.
8 Minimum distance between a flammable
material and the lighting unit.
9 Types of admissible lamps.
10 Type of lamp base accepted.
11 Serial number.
12 WEEE directive label.
13 Read manual.

1

5

69

2

4

13

7

8

10

3

1211

Section A - 5

TECHNICAL FILE

2500W HMI FOLLOWSPOT

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

CONNECTIONS.

Power supply unit

(P.S.U.)

1

2

3

4

5

d

e

B

C

A

6

7

1013+ / BS

A 1013+ / BS - Manual shutter version.
d - EM HARTING 16 x 16A power socket.

B Power supply unit.

C Lamp cable.

Cable H07 RN-F 18G 1,5 mm

2

length 3m fitted

with 16 x 16A M/F HARTING connectors.

Lighting unit / Power supply connection.

- Connect the lamp cable C to the connector 5 of the
ballast and connector d to the lighting unit.

- Lock the cable C into the cable lock e .

- Place the lamp into position - refer to section A - 11.

- Engage the circuit breaker 3 and check that the protection
4 is well engaged.

- Plug the cable 7 to the mains. If the power is present, the
checklight 1 lights up immediately.

- Engage the circuit breaker 2 .

WARNING !

- Never open the lamp house's bonnet when the lighting unit is on.

- Do not change the safety switches.

- Never connect to a dimmable channel.

- Use only when lamp in place.

Rating plate 6 : Lamp power.

DESCRIPTION.

Mains voltage.

- Check the conformity of the mains voltage input with the values indicated
on the identification plate of the PSU (mains voltage & lamp power)

• Use only the listed cables to connect to the mains ­ Refer to the respective PSU technical  le.

Section A - 7

TECHNICAL FILE

2500W HMI FOLLOWSPOT

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

CONNECTIONS.

Power supply unit
(P.S.U.)

Rating plate 6 : Lamp power.

Lighting unit / Power supply connection.

- Connect the lamp cable C to the connector 5 of the
ballast and connector e to the lighting unit.

- Lock the cable C into the cable lock j .

- Place the lamp into position - refer to section A - 10.

- Engage the circuit breaker 3 and check that the protection
4 is well engaged.

- Plug the cable 7 to the mains. If the power is present, the
checklight 1 lights up immediately.

- Engage the circuit breaker 2 .

WARNING !

- Never open the lamp house's bonnet when the lighting unit is on.

- Do not change the safety switches.

- Never connect to a dimmable channel.

- Use only when lamp in place.

f

e

g

h

i

A

C

D

j

B

1

3

4

5

6

7

2

1013+ B

Mains voltage.

- Check the conformity of the mains voltage input with the values indicated
on the identification plate of the PSU (mains voltage & lamp power)

A 1013+ B - Motorised shutter version.

e - EM HARTING 16 x 16A power socket.
f - EM XLR 4 output 0/+10V. (extra)
g - EM XLR 5 input DATA.
h - EF XLR 5 output DATA.
i - Fuse (10,3 x 38 - 2A.).

B Power supply unit.

C Lamp cable.

Cable H07 RN-F 18G 1,5 mm

2

length 3m fitted

with 16 x 16A M/F HARTING connectors.

D Analogue fader control (0/+10V).

DESCRIPTION.

• Use only the listed cables to connect to the mains ­ Refer to the respective PSU technical  le.

Section A - 9

TECHNICAL FILE

2500W HMI FOLLOWSPOT

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

A 1013+ M / (*)BSM - Motorised shutter version.

e - EM HARTING 6 x 35A. power socket.
*f - EM XLR 4 output 0/+10V. (extra)
*g - EM XLR 5 input DATA.
*h - EF XLR 5 output DATA.
*i - Fuse (10,3 x 38 - 2A.).

B Lamp cable.

Cable H07 RN-F 18G 1,5 mm

2

length 3m fitted

with 16 x 16A M/F HARTING connectors.

C Electronique power supply.

D Analogue fader control (0/+10V).

DESCRIPTION.

CONNECTIONS.

Electronic
power supply unit.

B

C

f

e

g

h

i

A

D

j

Lighting unit / Power supply connection.

- Connect the lighting unit's power cable B by passing it
inside the yoke.

- Leave a little slack and then block the cable B into the lock j .

- Place the lamp into position - refer to section A - 11.

- Connect the cable O to the mains.

WARNING !

- Never open the lamp house's bonnet when the lighting unit is on.

- Do not change the safety switches.

- Never connect to a dimmable channel.

- Use only when lamp in place.

1013+ M / BSM

Mains voltage.

- Check the conformity of the mains voltage input with the values indicated
on the identification plate of the PSU (mains voltage & lamp power)

• Use only the listed cables to connect to the mains ­ Refer to the respective PSU technical  le.

o

Section A - 11

TECHNICAL FILE

2500W HMI FOLLOWSPOT

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

1

a

1

1

150

3

2

2

3

6

1 1

2

7

9

10

4

2

3

5

5

9

2

2

10

11

6

8

4

12

12

!

!

PUTTING THE LAMP INTO PLACE.

User's instructions :

- Make sure the voltage is turned off.

- Lamp is cold.

- Avoid touching the bulb of the lamp.

MOUNTING THE HEATSINK ONTO THE BASES :

- Make sure that the guard rings a are well
placed on the neck of the heatsinks 1 .

PREPARATION OF THE JAW SOCKET :

- Raise the deflector plate.

- Unscrew the nuts 4 and raise the jaws 2 to the top of the shunks 5 .

- Turn the jaws 2 socket 90° to the exterior and place them onto the corner plates 3 .

POSITIONING THE LAMP :

- Position the lamp into place.

- Check that the heatsinks 1 are placed to the exterior of the isolating plates 7 .

- Place the jaws 2 onto the neck of the heatsinks.

- Make sure the necks of the heatsinks are placed well in the top and bottom jaws,
check by moving the mobile jaw 6 with the help of the lever 10 .

- Place the slots of the heatsinks horizontally 11 .

- Place the closing point of the lamp 9 upwards.

- Tighten the 2 nuts 4 with a 6 sided bolt-driver N° 13 8 and make sure you stay in axe 12 .

OVERHEAD VIEW

OVERHEAD VIEW

SIDE VIEW

FRONT VIEW

SIDE VIEW

Base : SFa 21 - 12

SIDE VIEW

Section A - 13

TECHNICAL FILE

2500W HMI FOLLOWSPOT

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

HMI 2500

ADMISSIBLE LAMP :

OSRAM : HMI 2500W/S

(Short model)

Manufacturer's recommendations :

• Read attentively the manufacturer's instructions.

• Positioning of the lamp and connecting of the power supply require great care. To make sure there is a good
conduction of current, the mechanical support and the electrical connections must be free from dirt and corrosion.
The clamps and brackets must be checked whenever the lighting unit has been transported.

• The lamp emits ultraviolet radiation. Direct exposure can be harmful to your health.

• It is recommended to avoid air draughts, also avoid exposing the lighting unit to bad weather.

• Use only when bulb in place

Technical characteristics :

User's precautions :

• The lamplife, as given by the manufacturer, is a theoretic lamplife duration as "in laboratory conditions",
a cycle based on 3 hours on / 1 hour off. Briefer cycles reduce the duration of the lamplife.

• In operating conditions, it is uncommon for the lamp to be still working after 200 to 300 hours. Its efficiency
can decrease by 30%.

• Premature wearing of lamp under performing conditions is mainly due to frequent switching on. Better leave
the lamp on, through the performance, rather than switching it on repeatedly. ( The lamplife is reduced about
1 hour, each time the lamp is switched on ). It is advised to wait for 10 minutes before switching on again.
(This extends the duration of the lamp.)

• Use over 500 hours of the lamp : change the lamp even if it still lights up.

New lamp :

• To achieve a good ionization of a new lamp, when using it for the first time, it is recommended to leave it on
for a few hours.

• Preserve carefully the guarantee slip of the lamp, as it may be asked for in the event of a dispute.

Thank you.

Voltage at the terminals of the lamp ....................................................................................... 115 Volts

Amperage at the terminals of the lamp ................................................................................25,6 Amps

Luminosity of the lamp ............................................................................................................240 000 lm

Luminous effectiveness .................................................................................................................96 lm/W

Colour temperature ..........................................................................................................................5600 K

Base .................................................................................................................................................SFa 21-12

Manufacturer’s rated life ...........................................................................................................500 hours

Section A - 15

TECHNICAL FILE

2500W HMI FOLLOWSPOT

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

DMX CONTROLS.

The shutter can be controlled on DMX 512
(connectors, encoders and Leds situated under the lighting unit’s zoom).

- 3 encoders give the DMX address for the shutter.

- 1 encoder "SELECT", gives you the following information :
0 : no DMX control.
1 : shutter DMX control.
2 : shutter and master DMX control on 2 successive channels.
3 to 9 : incorrect positions indicated by the red Led.

- 3 Leds, side by side, give you the following information :
Green (A) : indicates DATA is ON.
Red (B) : Lights up when there is a protocol error. Flashes when
address is out of the DMX range set
(0 or > Number of possible addresses)
or for a incorrect position of the "SELECT" encoder.
Yellow (C) : indicates +5V. is ON.

- 1 Led on the motor’s circuit board, visible on the shutter level :
Red (D) : Lights up when the motor is blocked.

The highest value overrides the command between the local control and a DMX
control. The master fixes the highest limit.

If an DMX address is out of range, the digital command is not acknowledged.

The last value of the digital command is saved by the memory when the DMX
network link is broken. The controls are regained when the command is higher than
the last value saved.

NETWORK USE

DIGITAL

(DMX)

DMX LINK USE.

Wiring when using a manual power supply.

IN OUT IN OUT

Example of the master function.

Address of the encoders =100
SELECT encoder = 2
Channel 100 = Shutter
Channel 101 = Master

Local control Channel 100 Channel 101 Result
Shutter Shutter Master

Ex. 1 0 0 to 100% 100% The shutter opens : 0 to 100%
Ex. 2 0 0 to 100% 50% The shutter opens : 0 to 50%
Ex. 3 0 to 100% 0 100% The shutter opens : 0 to 100%
Ex. 4 0 to 100% 0 50% The shutter opens : 0 to 50%
Ex. 5 0 to 100% 20% 80% The shutter opens : 20% to 80%

Grouping the shutter DMX controls (same channels or groupings on the lighting board), allows synchronizing for a whole
set of followspots.

Wiring when using a DMX power supply.

IN OUT IN OUT

A

B

C

D

1013+ B

Section A - 17

TECHNICAL FILE

2500W HMI FOLLOWSPOT

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

CONNECTION

a & f b,c & d

1 Fan phase.
2 Ballast phase.
3 Lamp Neutral.
4
5
6 Security return 1200.
7 Security return 2500.
8 Security not used.

9 Ignition timed phase.
10 Ballast phase.
11 Lamp Neutral.
12 Earth.
13 Aux. phase.
14 Aux. Neutral.
15 Common security.
16 Earth.
Female side earth only.

g

Lamp cable.

Ballast side.

FMD 16 x16 A

HARTING

h

Lighting unit side.

FFD 16 x16 A

HARTING

Cable H07 RN-F

18G 1,5mm

2

REP

DESIGNATION DESIGNATION

REP

1 0V.
2 DATA - IN.
3 DATA + IN.
4
5

1 0V.
2 DATA - OUT.
3 DATA + OUT.
4
5

DESIGNATION

REP

DESIGNATION

REP

Flexible cable

5 x 0,14 shielded

CN5.

FF XLR 5. FM XLR 5.

Flexible cable

5 x 0,14 shielded

CN5.

e

1 0V.
2
3 0/+10V. Shutter
4 +15V.

DESIGNATION

REP

FF XLR 4.

Flexible cable

4 x 0,14 shielded

CN5

DATA Link.

Delivered standard : 3m.

Note: This is a universal cable and is suitable for a follow spot
or a prole, 1200W. or 2500W.

a g b c

d

h

f

e

1013+ /

B / BS

Section B - 1

TECHNICAL FILE

2500W HMI FOLLOWSPOT

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

MIRROR.

- Disconnect from the mains.

- Open the lamp house's bonnet.

- Take out the lamp.
( Refer to section 11 and proceed in reverse order).

- Clean the mirror 4 with a soft dry cloth.

- Remount parts in reverse order.

CONDENSER.

- Disconnect from the mains.

- Open the lamp house's bonnet.

- Take out the lamp.
( Refer to section 11 and proceed in reverse order).

- Turn the fast lock 1 .

- Withdraw the lens holder 2 .

- Clean the lens 3 with a soft dry cloth.

- Remount parts in reverse order.

- Clean in the same way, the 2 lenses found in the lens tube.

Disconnect from the mains before any servicing.

Service only by qualified technician.

MAINTENANCE

1 mm

SPARK-GAP.

- Disconnect from the mains.

- Open the lamp house bonnet.

- Check the distance of the electrodes that should be 1mm.
(If you notice a larger gap, then please contact the ROBERT JULIAT's
technical department).

[e-mail]

DOSSIER TECHNIQUE

POURSUITE HMI 2500W

Section B - 3

1013+ /

B, BS, M & BSM

Le constructeur se réserve la possibilité de modi er ses matériels sans avis préalable. Les renseignements mentionnés sur cette notice sont donnés à titre indicatif et ne sauraient présenter de caractère contractuel.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

NON-FUNCTIONING DIAGNOSIS.

OPERATION SYMPTOMS POSSIBLE CAUSES REMEDIES

3

4

1 2

THE POWER
SUPPLY UNIT

1 HMI lamp ON.
or OFF checklight.
2 Rocker switch.
3 Mains checklight.
4 Circuit breacker.

No light in the
lamp house side.

Checklight 3 does
not light up when the
power supply unit is
connected.

Rocker switch 2 in ON
position, checklight 1
is o.

Diculty in lighting.

Mains absence.

Lamp failure.

Automatic breaker and
transformer are OFF.

Badly adjusted
spark-gap.

Check the mains and
cable connections.
Refer to section A - 5 & 17.

Repeat the operation.

Turn ON the automatic
breaker 4 .

Bad contact. Harting plug
power supply / Lighting
unit.

Lantern bonnet badly
closed.

Check the connections.
Refer to section A - 17.

Make sure bonnet is
properly closed. Adjust the
position of the mini-circuit
breaker.

Lamp is badly mounted.

Failure to ignite
(ignition block, spark-gap).

Open colour unit at the
front of the lighting unit.

Check gobo frame.

Colour changer unit
closed.

Gobo frame changer
badly positioned.

Iris cassette badly
remounted.

Reector and lenses not
in good condition.

Dirty lters.No ventilation from the lamp house.

Bad quality light beam.

No light in the zoom side.

(Lamp house alight).

No light in the lamp house side.

LIGHTING UNIT

(Checklight 1 o).

(Checklight 1 on).

LIGHTING UNIT

Refer to section B - 1.

Refer to section B - 1.

Refer to section A - 11.

Check cables and lamp.

Refer to section B - 1.

Remount correctly the
iris cassette.
Refer to section C - 5.

Change lters.
Refer to section C - 1.

3

4

1

2

1013+

TECHNICAL FILE / DOSSIER TECHNIQUE

2500W HMI FOLLOWSPOT / POURSUITE HMI 2500W

Section B - 5

1013+ /

B, BS, M & BSM

Robert Juliat reserve the right to change or alter any of the items detailed on this page, to increase or improve manufacturing techniques without prior notice.

Le constructeur se réserve la possibilité de modi er ses matériels sans avis préalable. Les renseignements mentionnés sur cette notice sont donnés à titre indicatif et ne sauraient présenter de caractère contractuel.

robert juliat Route de Beaumont F 60530 Fresnoy-en-Thelle phone: [phone] - fax: [phone] - www.robertjuliat.fr

1013+ /

B / BS

LANTERNE / LAMP HOUSING

PLAN ELECTRIQUE /

ELECTRICAL DIAGRAM

NOMENCLATURE PIECES DETACHEES /

SPARE PARTS LIST.

CODE DESCRIPTION

REP

Section C - 1

PROJECTEUR DE POURSUITE HMI 2500W

2500W HMI FOLLOWSPOT

Measurements are in mm / Mesures en mm.

Robert Juliat reserve the right to change or alter any of the items detailed on this

page, to increase or improve manufacturing techniques without prior notice.

Le constructeur se réserve la possibilité de modi er ses matériels sans avis préalable. Les renseignements

mentionnés sur cette notice sont donnés à titre indicatif et ne sauraient présenter de caractère contractuel.

!

ATTENTION - Pour passer une commande de pièces détachées, utiliser toujours les codes. / WARNING - Always use the codes, when ordering spare parts.

!

PIECES EXTERIEURES /

OUTER PARTS.

1

2

3

4

5

6

7
8
9

10

11
12

13

13

13*

14

15

16

PD10130005

DJ20249701

1013P20002

AFGA000001

AFG0000002

DJ30625000

1013P20008
DU40022200
DJ30280203

1015P20011

DJ40555600
BO06020003

1013P20016

1015P21001

ME14220207

BO10000008

DJ40870501

DJ40773500

Capot de lanterne complet /

Complete lamp housing bonnet.

Capot supérieur iris / Upper shutter cover.

Capot de zoom complet /

Complete lens tube bonnet.

Crochet / Hook.

Grenouillère / Safety lock.

Poignée latérale revêtue /

Ergonomic handle.

Poignée complète / Complete handle.
Palier de fourche / York bearing.
Poignée débrayable M12 /

M12 fast locking handle.

Fourche renforcée orientable (tube) montée /

Heavy duty adjustable yoke.

Bride du câble / Cable lock.
Bouton mâle / Male knob.

1013/1015 version manuelle /

1013/1015 manual version :

Capot dessous zoom complet /

Complete lower lens tube cover.

1013B/1015B version motoriée /

1013B/1015B motorised version :

Capot dessous zoom complet /

Complete lower lens tube cover.

Ventilateur seul / Fan (120x120mm).

Bouton / Knob.

Filtres capot lanterne /

Filters for lamp housing.

Contre poids / Counter weight.

ZOOM /

LENS TUBE

LANTERNE /

LAMP HOUSING

CHANGEUR 6 COULEURS /

6 COLOUR CHANGER
UNIT

1

2

3

4

5

7

8

9

10

11

12

13*

14

15

6

16

1013+ /

B / BS / M / BSM

13

NOMENCLATURE PIECES DETACHEES /

SPARE PARTS LIST.

CODE DESCRIPTION

REP

Section C - 2

PROJECTEUR DE POURSUITE HMI 2500W

2500W HMI FOLLOWSPOT

Measurements are in mm / Mesures en mm.

Robert Juliat reserve the right to change or alter any of the items detailed on this

page, to increase or improve manufacturing techniques without prior notice.

Le constructeur se réserve la possibilité de modi er ses matériels sans avis préalable. Les renseignements

mentionnés sur cette notice sont donnés à titre indicatif et ne sauraient présenter de caractère contractuel.

!

ATTENTION - Pour passer une commande de pièces détachées, utiliser toujours les codes. / WARNING - Always use the codes, when ordering spare parts.

!

1

2

3

4

5

1

2
3

4

5

1

2

1013P30200

1013P30102

1013P30106

CF00300040

PD10130027

PD10130026

1013P30010

1013P30002

PD10130011
PD10130010

DJ40263500

1013P30003

PD10130016

DJ30244601

1013P30004

Changeur 6 couleurs complet /

Complete 6 way colour changer unit.

Capot / Bonnet.

Mécanisme complet / Complete mechanism.
(Sans porte- ltre / Without  lter holder).

Butée caoutchouc adhesive /

Rubber shock absorber (Interior).

Butée / Shock absorber (Interior).

Butée plastique / Plastic shock absorber (Exterior).

Changeur 6 couleurs complet /

Complete 6 way colour changer unit.

Capot / Bonnet.

Butée / Shock absorber (Interior).
Butée plastique / Plastic shock absorber (Exterior).

Tige / Rod.

Tirette / Sliding handle.

Porte  ltre complet (sans gélatine) /

Complete  lter frame (without  lter).

Rondelle / Disk (Ø268).

Support avec clips montés /
Disk holder with mounted clips.

A - VERSION BOOMERANG /

BOOMERANG VERSION.

(STANDARD)

B - VERSION A TIRETTES /

PUSH / PULL VERSION.

(OPTION)

PORTE FILTRE / FILTER HOLDER.

(Pour les 2 versions / For both versions).

1013+ /

B / BS / M / BSM

NOMENCLATURE PIECES DETACHEES /

SPARE PARTS LIST.

CODE DESCRIPTION

REP

Section C - 3

PROJECTEUR DE POURSUITE HMI 2500W

2500W HMI FOLLOWSPOT

Measurements are in mm / Mesures en mm.

Robert Juliat reserve the right to change or alter any of the items detailed on this

page, to increase or improve manufacturing techniques without prior notice.

Le constructeur se réserve la possibilité de modi er ses matériels sans avis préalable. Les renseignements

mentionnés sur cette notice sont donnés à titre indicatif et ne sauraient présenter de caractère contractuel.

!

ATTENTION - Pour passer une commande de pièces détachées, utiliser toujours les codes. / WARNING - Always use the codes, when ordering spare parts.

!

PIECES INTERIEURES ZOOM /

LENS TUBE INNER PARTS.

1013+ / M

OP25410001
DU40423601
VI04010053
VI04020001

ME07140301
VI19050002
DU40242901
DU40243100

DU40231500
VI04010002
DU40264500
DU40264800
BO06000010

VI03010008
DU40231500
VI04010002
VI14030001
DJ40290100
DU40264900
VI08030006
VI08010001
DU30222051
1013P20009

ME10010201
DU40236103
DU40236102
VI14050001
DU40081804

OP11010004
VI04020001
VI04030010

DU30221951
DU30222109
DJ40450802
DJ40505000
VI04010055

1
34
35
36

2

3

4

5

6

7

8

9
10

11
12
13
14
15
16
17
18
19
20

21
22
23
24
25

26
27
28

29
30
31
32
33

3 4

5

1

2

10

6 7 8 9

1112

14

15

16

13

18

17

19

20

25

23

21

22

26

24

30

28

27

32

28

31

29

33

343536 28

Lentille / Lens (Ø254).
Pince Lentille / Lens clip.
Vis / Screw (M4).
Ecrou / Nut (M4).

Butée / Block stopper.
Clips.
Palier Té on / Te on bearing.
Tige / Rod.

Pignon conique / Bevel gear wheel.
Vis / Screw (M4).
Bague / Roller.
Tige / Shank.
Bouton / Knob.

Vis / Screw (M3).
Pignon conique / Bevel gear wheel.
Vis / Screw (M4).
Rondelle / Washer (Ø14).
Butée / Block stopper.
Tige / Shank (Ø6).
Rondelle / Washer (Ø8).
Vis / Screw (M8).
Colonnette / Strut.
Obturateur complet manuel /

Complete manuel shutter.

Manchon silicone / Silicone protection.
Tige / Rod.
Tige / Rod.
Clips.
Palier Té on / Te on bearing.

Lentille arrière / Rear lens (Ø110).
Ecrous / Nut (M4).
Rondelle contact à Picots /
Contact washer (Ø4).
Entretoise / Spacer.
Colonnette / Strut.
Rondelle emboutie / Lens washer (Ø4).
Rondelle de pression / Washer.
Vis / Screw (M4).

NOMENCLATURE PIECES DETACHEES /

SPARE PARTS LIST.

CODE DESCRIPTION

REP

Section C - 4

PROJECTEUR DE POURSUITE HMI 2500W

2500W HMI FOLLOWSPOT

Measurements are in mm / Mesures en mm.

Robert Juliat reserve the right to change or alter any of the items detailed on this

page, to increase or improve manufacturing techniques without prior notice.

Le constructeur se réserve la possibilité de modi er ses matériels sans avis préalable. Les renseignements

mentionnés sur cette notice sont donnés à titre indicatif et ne sauraient présenter de caractère contractuel.

!

ATTENTION - Pour passer une commande de pièces détachées, utiliser toujours les codes. / WARNING - Always use the codes, when ordering spare parts.

!

1013+ B /

BS / BSM

OP25410001
DU40423601
VI04010053
VI04020001
VI04030010

ME07140301
VI19050002
DU40242901
DU40243100

VI14030001
DJ40290100

VI08030004
VI08010001
DU30222051

1013P21006

ME10010201
DU40236103
DU40236102
VI14050001
DU40081804

OP11010004
VI04020001
VI04030010
DU30221951
DU30222109
DJ40450802
DJ40505000
VI04010055

ME03002501

OA00000010

Lentille / Lens (Ø254).
Pince Lentille / Lens clip.
Vis / Screw (M4).
Ecrou / Nut (M4).
Rondelle / Washer (M4).

Butée / Block stopper.
Clips.
Palier Té on / Te on bearing.
Tige / Rod.

Rondelle / Washer (Ø14).
Butée / Block stopper.

Rondelle / Washer (Ø8).
Vis / Screw (M8).
Colonnette / Strut.

Obturateur complet motorisé CAD 2000 /

Complete CAD 2000 motorised shutter.

Manchon silicone / Silicone protection.
Tige / Rod.
Tige / Rod.
Clips .
Palier Té on / Te on bearing.

Lentille arrière / Rear lens (Ø110).
Ecrous / Nut (M4).
Rondelle de contacts / Contact washer (Ø4).
Entretoise / Spacer.
Colonnette / Strut.
Rondelle emboutie / Lens washer (Ø4).
Rondelle de pression / Washer.
Vis / Screw (M4).

Fusible / Fuse - 10,3 x 38.
(Accessible sous le projecteur /
accessible under the lighting unit’s zoom).

Moto-reducteur D.C. complet /

Complete D.C. motor.

1
25
26
27
28

2

3

4

5

6

7

8

9
10

11

12
13
14
15
16

17
18
19
20
21
22
23
24

25

26

PIECES INTERIEURES ZOOM /

LENS TUBE INNER PARTS.

1

2

3 4

5

6

7

8

9

10

11

16

14

12

13

21

19

18

17

15

23

19

22

26

25

20

24

252627 28

NOMENCLATURE PIECES DETACHEES /

SPARE PARTS LIST.

CODE

REP

DESCRIPTION

PROJECTEURS POURSUITE HMI 2500W /

2500W HMI FOLLOWSPOTS

Section C - 5

Measurements are in mm / Mesures en mm.

Robert Juliat reserve the right to change or alter any of the items detailed on this

page, to increase or improve manufacturing techniques without prior notice.

Le constructeur se réserve la possibilité de modi er ses matériels sans avis préalable. Les renseignements

mentionnés sur cette notice sont donnés à titre indicatif et ne sauraient présenter de caractère contractuel.

!

ATTENTION - Pour passer une commande de pièces détachées, utiliser toujours les codes. / WARNING - Always use the codes, when ordering spare parts.

!

1013+ /

B / BS / M / BSM

28

2627 5 25 16

31

4

1

3

8

14

24

32

9

20

6

10

1813

25

15

19

11

7

23

2

17

12

32

22

21 29

B

Position vis rep "B" pour Ø55 /
Rep "B" screw (VI02010005)
position for Ø55 :
1013+ & 1015.

Ø55

B size

RJ306600

DETAIL "B"

A

DETAIL "B"

A FPAIRIS018 Ensemble cassette iris montée / Complete black-out iris cassette.

1 DJ30659250 Platine cassette iris / Iris main plate.
2 DU40659100 Axe galet de guidage / Roller axle.
3 DU40659000 Galet de guidage en té on / Te on roller.
4 DJ40659550 Plaque porte-galets mobile / Mobile roller support.
5 DU40659300 Colonnette point  xe iris / Strut  xing point for iris.
6 DJ40659400 Volets protège lames / Protection blades.
7 DU40659800 Ensemble côté commande avec palier serti / Side unit control with crimped bearing.
8 DU40478200 Axe de roue dentée / Gear axle.
9 DU40659600 Pignon intermédiaire 96 dents / 96 gear (module 0,5).
10 PO00000028 Poignée débrayable noire femelle / Female black fast locking handle (M8).
11 DU40231500 Pignon conique 18 dents / 18 teeth gear (module 1).
12 DJ40797900 Plaque de maintien soudée / Welded plate.
13 DU40638700 Axe de manoeuvre / Driving axle.
14 DU40088600 Roue 120 dents avec pignon conique serti / 120 teeth gear with crimped gear.
15 VI0303009 Rondelle plate / Washer (Ø3).
16 VI04030002 Rondelle plate / Washer (Ø4).
17 VI04030003 Rondelle plate / Washer (Ø4).
18 VI08030006 Rondelle contact à picot / Contact washer (Ø8).
19 VI03010003 Vis / Screw (M3).
20 VI03010037 Vis / Screw (M3).
21 VI03010006 Vis / Screw (M3).
22 VI03010026 Vis / Screw (M3).
23 VI04010002 Vis sans tête à bout cuvette / Setscrew (M4).
24 VI03010027 Vis / Screw (M3).
25 VI04020017 Ecrou frein fendu / Locknut (M4).
26 DU30221957 Entretoise lisse / Spacer.
27 DU30221951 Entretoise lisse / Spacer.
28 DU30222138 Colonnette / Spacer.
29 IN75000004 Iris nu / Iris (Ø75).
30 CF00000004 Frein  let fort / Locking glue.
31 BO06010001 Bouton borne femelle / Female end knob.
32 VI06030002 Rondelle plate / Washer (Ø6).

NOMENCLATURE PIECES DETACHEES /

SPARE PARTS LIST.

CODE DESCRIPTION

REP

Section C - 6

PROJECTEUR DE POURSUITE HMI 2500W

2500W HMI FOLLOWSPOT

Measurements are in mm / Mesures en mm.

Robert Juliat reserve the right to change or alter any of the items detailed on this

page, to increase or improve manufacturing techniques without prior notice.

Le constructeur se réserve la possibilité de modi er ses matériels sans avis préalable. Les renseignements

mentionnés sur cette notice sont donnés à titre indicatif et ne sauraient présenter de caractère contractuel.

!

ATTENTION - Pour passer une commande de pièces détachées, utiliser toujours les codes. / WARNING - Always use the codes, when ordering spare parts.

!

LANTERNE /

LAMP HOUSING.

SUPPORT DOUILLE /

SOCKET HOLDER.

LAMPE / LAMP.

1

3

6

7

4

5

9

8

10

11

12

1

2

3

5 6

7

1

3

2

4

2

13

1013P10009

1013P10211

ME15100003

ME15100017

ME14024106
1013P10027
ME15110001
PD10130017
COUA000032
COU0016101

COU0006101

FPACO00013

FPACO00014

FPACO00057

ME14000002

VI08020002
DU40261400
DU40236800

DU40237000

DU40236900

DT40316100
DU40247302

DU30279500

RLA1435002

DT40279400

PD10130013

Porte-lentille complet avec lentille QUARTZ /

Complete lens holder with QUARTZ lens.

Voir détails / See details: Section C - 7.
Porte-miroir complet avec miroir /

A complete re ector holder with re ector.

Voir détails / See details: Section C - 7.

Amorceur complet / Ignition block

(1013+ / B /BS).

Amorceur complet électronique /

Electronical ignition block. (1013+ M / BSM).

Ventilateur / Fan (80 x 80 x 25).
Ventilateur / Fan.
Eclateur / Spark gap.
Minirupteur complet / Micro switch.
Embase Aluminium/ Aluminium socket.
Connecteur mâle Harting 16 contacts x 16A + T /

16 x 16A contacts + Earth, Harting male connector

(1013+ / B /BS).

Connecteur mâle Harting 6 contacts x 35A + T /

6 x 35A contacts + Earth, Harting male connector

(1013+ M / BSM).

Cordon montée de lampe L=3m (Standard).

Lamp cable L=3m (Standard).

Cordon montée de lampe L=10m (Option).

Lamp cable L=10m (Option).

Cordon montée de lampe "MITRONICS" (Option).

Lamp cable "MITRONICS" L=3m (Option).

(1013+ M / BSM).

Fixation amortisseur / Noise blocker.

Ecrou / Nut (M8).
Goujon / Studbolt (M8).
Demi mâchoire supérieure /

1/2 upper jaw-socket.

Demi mâchoire inférieure  xe /

1/2 lower  xed jaw-socket.

Demi mâchoire inférieure mobile /

1/2 lower mobile jaw-socket.

Ressort / Spring.
Axe / Axle.

Demi-dissipateur / Half a heatsink .

Lampe / Lamp - HMI 2500 W/S OSRAM.

Jonc / Guard ring.

Dissipateur complet droit ou gauche /
Complete heatsink, right or left.

1

2

3

4

5

6

7

8

9

10

11

12

13

1

2

3

4

5

6

7

1

2

3

1013+ /

B / BS / M / BSM

NOMENCLATURE PIECES DETACHEES /

SPARE PARTS LIST.

CODE

REP

DESCRIPTION

PROJECTEURS POURSUITE HMI 2500W /

2500W HMI FOLLOWSPOTS

Section C - 7

Measurements are in mm / Mesures en mm.

Robert Juliat reserve the right to change or alter any of the items detailed on this

page, to increase or improve manufacturing techniques without prior notice.

Le constructeur se réserve la possibilité de modi er ses matériels sans avis préalable. Les renseignements

mentionnés sur cette notice sont donnés à titre indicatif et ne sauraient présenter de caractère contractuel.

!

ATTENTION - Pour passer une commande de pièces détachées, utiliser toujours les codes. / WARNING - Always use the codes, when ordering spare parts.

!

DETAIL SUPPORT

LENTILLE ASPHERIQUE /

ASPHERIC LENS HOLDER DETAIL.

1

2

3

4

5

1013P10009 Support asphérique 1013/1015 QUARTZ monté /

Lens holder 1013/1015, with QUARTZ lens.

1 AFV0000004 Verrou / Lo ck.
2 AFVA000008 Jonc / Lock ring.

3 DJ40330200 Porte lentille asphérique /

Aspheric lens holder.

4 OP06020002 Lentille asphérique QUARTZ /

QUARTZ Aspheric lens.

5 DU40333400 Plaque écran vitrocéramique / Screen plate.

Montage de la lentille asphérique /

Mounting the aspheric lens.

6 VI03010028 Vis / Screw.
7 VI03030004 Rondelle / Washer.
8 DT40280801 Ressort / Spring.
9 DU40280701 Entretoise / Strut.

10 VI03030006 Rondelle / Washer.

6

6

789

10

1013+ /

B / BS / M / BSM

DETAIL PORTE-MIROIR /

MIRROR HOLDER DETAIL.

1013P10211 Kit porte-miroir complet avec miroir pour mise à jour des modèles avant 2004 /

Complete mirror holder and mirror kit to up-date models before 2004.

1 DU40601900 Support miroir / Mirror holder.
2 PD10150023 (*) Miroir complet sans support miroir /

(*) Complete mirror without mirror holder.

1

2*

NOMENCLATURE PIECES DETACHEES /

SPARE PARTS LIST.

CODE DESCRIPTION

REP

Section C - 8

PROJECTEUR DE POURSUITE HMI 2500W

2500W HMI FOLLOWSPOT

Measurements are in mm / Mesures en mm.

Robert Juliat reserve the right to change or alter any of the items detailed on this

page, to increase or improve manufacturing techniques without prior notice.

Le constructeur se réserve la possibilité de modi er ses matériels sans avis préalable. Les renseignements

mentionnés sur cette notice sont donnés à titre indicatif et ne sauraient présenter de caractère contractuel.

!

ATTENTION - Pour passer une commande de pièces détachées, utiliser toujours les codes. / WARNING - Always use the codes, when ordering spare parts.

!

POIGNEE DE BLOCAGE DU ZOOM /

ZOOM HANDLE LOCK.

1013P20008

VI04010043
VI04030005
DU40253700

PD10130033

PD10130034

VI03010003
VI03030002
PD10130008
DJ40274301
PD10130009
DJ40211603
BO04010007

FPADIV0052

Réglage pression / Pressure adjustment.

Pour augmenter la pression desserrer la vis a .

Unscrew the screw a , to increase the pressure.

Pour diminuer la pression serrer la vis a .

Tighten the screw a , to decrease the pressure.

Poignée complète / Complete handle.

Vis / Screw (M4).
Rondelle / Washer (Ø4).
Patin / Rubber block (Ø12).

Verre dépoli avec support /

Soft glass with holder.

Filtre correcteur avec support /

Correction  lter with holder 5500K → 3400K.

Vis / Screw (M3).
Rondelle à dent / Washer.
Butée / Block stopper.
Bras / Arm.
Butée / Block stopper.
Tige de manœuvre / Driving shank.
Bouton / Knob (M4).

OPTION :
Guillotine / Chopper (Ø56).

1

2

3

1

2

3

4

5

6

7

8

9

3

5

4

7

8

6

1

2

9

SUPPORT GOBO /

GOBO HOLDER.

SUPPORT FILTRE VERRE /

GLASS FILTER HOLDER.

1013+ /

B / BS / M / BSM

1

a

2

3

1 FPADIV0061 Support gobo taille "B" /

"B" size gobo holder.

2 PO00000018 Poignée de couteau grise / Gray handle

3 DU40722400 Axe épaulé / Shoulder axle.

4 VI04040014 Rivet creux / Rivet.

5 VI03020009 Ecrou / Nut (M3).

6 DT40714200 Languette de maintien gobo / Gobo clip.

3

1

6

5

4

2