Robe ROBIN iParfect 150 RGBA, ROBIN iParfect 150 RGBA Wireless DMX, ROBIN iParfect 150 FW RGBA, ROBIN iParfect 150 FW RGBA Wireless DMX User Manual
1
Version 1.3
2
Table of contents
1. Safety instructions ......................................................................................................... 3
2. Fixture exterior view ...................................................................................................... 5
3. Installation....................................................................................................................... 6
3.1 Connection to the mains ............................................................................................ 6
3.2 Installing barndoors and the gel frame ....................................................................... 7
3.4 Rigging the xture ...................................................................................................... 9
3.5 DMX-512 connection ................................................................................................ 11
3.6. Wireless DMX operation ......................................................................................... 12
4. Control menu map ........................................................................................................ 13
5. Control menu (Standard and Easy control mode) ..................................................... 15
5.1 Addressing (DMXA) .................................................................................................. 16
5.2 Fixture information (Info) .......................................................................................... 16
5.3 Personality (Pers) ..................................................................................................... 16
5.4 Manual Control (Manual) .......................................................................................... 17
5.5 Test program (Test Prg) ............................................................................................ 17
5.6 Stand-alone (St Alone) ............................................................................................. 17
5.7 Reset function (Reset) ............................................................................................. 18
5.8 Special functions (Special) ....................................................................................... 18
6. RDM ............................................................................................................................... 20
7. Error and information messages ................................................................................ 21
8. Technical Specications .............................................................................................. 21
9. Maintenance and cleaning ........................................................................................... 23
9.1 Replacing the fuse ................................................................................................... 24
9.2 Disposing of the product .......................................................................................... 24
10. Photometric diagrams................................................................................................ 25
ROBIN iParfect 150 RGBA
ROBIN iParfect 150 WF RGBA
3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR iParfect 150 !
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
The iParfect 150 was designed for outdoor use and it is intended for
professional application only. It is not for household use.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!
Make sure that the available voltage is not higher than stated on the rear panel of the xture.
This xture should be operated only from the type of power source indicated on the marking label. If you are
not sure of the type of power supplied, consult your authorized distributor or local power company.
Always disconnect the xture from AC power before cleaning, removing or installing any part of the xture.
The power plug has to be accessible after installing the xture. Do not overload wall outlets and extension cords
as this can result in re or electric shock.
Do not allow anything to rest on the power cord. Do not locate this xture where the cord may be damaged by
persons walking on it.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture and the power
cord from time to time.
Refer servicing to qualied service personnel.
This xture falls under protection class I. Therefore this xture has to be connected to
a mains socket outlet with a protective earthing connection.
Do not connect this xture to a dimmer pack.
Warning!
LED light emission. Risk of eye injury. Do not look into the beam at short distance of
the of the product. Do not view the light output with optical instruments or
any device that may conncentrate the beam.
The light source contains blue LEDs.
Avoid brute force when installing or operating the xture.
When choosing the installation spot, please make sure that the xture is not exposed to extreme heat, or dust.
Do not block the front transparent glass with any object when the xture is under
operation.
4
Housing of the xture should never be covered with cloth or other materials.
This xture should not be placed in a built-in installation unless proper ventilation is provided.
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fastened.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.
To avoid damage of an internal optical system of the xture, never let the sunlight (or
other light source) lights directly to the lens array, even when the xture is not working
The xture becomes very hot during operation. Allow the xture to cool approximately 30 minutes prior to
servicing or maintenance.
Operate the xture only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the xture. Most damages are the result of unprofessional operation!
Please use the original packaging if the xture is to be transported.
Please consider that unauthorized modications on the xture are forbidden due to safety reasons!
If this device will be operated in any way dierent to the one described in this manual, the product may suer
damages and the guarantee becomes void.
5
2. Fixture exterior view
5 - Mounting hole for clamp
6 - Attachment point for accessories
7 - DMX OUT (with sealing cover)*
8 - Mains IN (with sealing cover)*
9 - Mains OUT (with sealing cover)*
10 - DMX IN (with sealing cover)*
11 - Display and control buttons
1 - Mounting bracket
2 - Tilt locks
3 - Lens array with transparent
glass cover
4 - Accessory frame adaptor
*IMPORTANT!
Fixture´s power connectors (8, 9) are dust and water protected according to protection class IP 65 by
mating with related power connectors with cords (IP 65 rated) or by covering with the rubber sealing
covers . They cannot stay uncovered outdoor (e.g. during xture installation).
Fixture´s DMX connectors (7, 10) are dust and water protected according to protection class IP 65 by
mating with related power connectors with cords (IP 65 rated) or by covering with the rubber sealing
covers . They cannot stay uncovered outdoor (e.g. during xture installation).
6
3. Installation
Fixtures must be installed by a Qualied electrician in accordance with
all national and local electrical and construction codes and regulation.
3.1 Connection to the mains
For protection from electric shock, the xture must be earthed!
The iParfect 150 is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC
power source from 100-240 Volts.
Install a cord cap on the power cable to allow connection to power outlet, install a grounding-type (earthed)
plug with suitable IP rating , following the plug manufacturer’s instructions.
If you have any doubts about proper installation, consult a qualied electrician.
Core (EU) Core (US) Connection Plug Terminal Marking
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth
This device falls under class one and must be earthed (grounded)!
The max. number of connected xtures in power chain depends on AC mains power voltage:
CE: ETL:
15 xtures at power supply= 230V 9 xtures at power supply= 230V
13 xtures at power supply= 208V 8 xtures at power supply= 208V
7 xtures at power supply= 120V 4 xtures at power supply= 120V
Actual number of xtures may dier from values stated above as you have to take into account the length of
supply cables, circuit breaker etc. at projecting of the xtures installation Do not overload the supply line and
connecting leads.
Wiring and connection work must be carried out by qualied sta!
.
7
3.2 Installing barndoors and the gel frame
Disconnect the xture from mains before barndoors and the gel frame installation!
1. Unlock the spring lock (1) of the accessory frame adaptor (2) via pushing this spring lock as show red arrows
on the picture.
2. Insert the gel frame (3) into the bottom slots of the accessory frame adaptor (2).
3. Insert the barndoors (4) into the top slots of the frame adaptor (2).
4. Secure both accessories by moving the spring lock (1) to locked position as shows the red arrow on the picture.
8
Note: the barndoors can be rotated to desired position and secured in this position via the securing screw (5).
9
3.4 Rigging the xture
A structure intended for installation of the xture(s) must safely hold weight of the xture(s) placed on it. The
structure has to be certicated to the purpose.
The xture must be installed in accordance with national and local electrical and construction codes and regulation.
For overhead installation, the xture must be always secured with a safety wire.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working
load limits, installation material being used, and periodic safety inspection of all installation material and the
projector. If you lack these qualications, do not attempt the installation yourself, but use a help of professional
companies.
CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety
of a possible installation, do not install the xture!
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
Allow the xture to cool for ten minutes before handling with it.
The xture has to be installed out of the reach of public.
The xture must never be xed swinging freely in the room.
When installing the device, make sure there is no highly inammable
material (decoration articles, etc.) in a distance of min. 0.4 m.
Use an appropriate clamp to rig the xture on the truss.
Make sure that the device is xed properly! Ensure the
structure (truss) to which you are attaching the xtures is secure.
When installing xtures side-by-side, avoid illuminating one xture with another!
The xture can stand on the stage oor ( by means of the unfolded mounting bracket) or rigged on a truss (via
folded mounting bracket) without altering its operation characte ristics.
.
10
For securing the xture to the truss, install a safety wire which can hold at least 10 times the weight of the xture.
Use only the safety wire with snap hooks with screw lock gates. Fasten the safety cable around the truss and
the mounting bracket as shown on the picture below.
1-Clamp
2-Truss
3-Mounting bracket
4-Safety wire
Loading...