Version 1.2
2
Table of contents
1. Safety instructions ......................................................................................................... 3
2. Description of the xture .............................................................................................. 4
3. Installation....................................................................................................................... 4
3.1 Mounting the pixelPATT ............................................................................................ 4
3.2 Connecting the pixelPATT with the PATT Driver ........................................................ 4
4. Technical specications ................................................................................................ 6
3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE INSTALLING THE PRODUCT .
1. Safety instructions
CAUTION!
The PixelPATT was designed for indoor use only.
The product is for professional use only, it is not for household use.
This product has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the product.
If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched o until
it has reached room temperature.
The pixel PATT should be operated with the PATT Driver only.
The PixelPATT becomes hot during its operation, a
llow it to cool prior
to manipulation.
The pixelPATT unit never must be covered with cloth or other materials during
operation.
Refer servicing to qualied service personnel.
Warning! Risk Group 2 LED product according to EN 62471
LED light emission. Risk of eye injury. Do not look into the beam at short distance of
the of the product. Do not view the light output with optical instruments or any
device that may conncentrate the beam.
The light source contains blue LEDs.
When choosing the installation spot, please make sure that the pixelPATT are not exposed to extreme heat,
moisture or dust.
Operate the pixelPATT only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the pixelPATT. Most damages are the result of unprofessional operation!
Please use the original packaging if the pixelPATT is to be transported.
Please consider that unauthorized modications on the xture are forbidden due to safety reasons!
4
2. Description of the xture
Pixel positions
1 - Parabolic aluminium reectors
2 - Mounting yoke
3 - Tilt lock
4 - Mounting hole
5 - Control Input (4-pin XLR)
5
3. Installation
The PixelPatt must be installed by a qualied electrician in accordance with all
national and local electrical and construction codes and regulations.
3.1 Mounting the pixelPATT
The xture can be rigged to the truss or fastened to the oor stand via a mounting yoke. The hole of diameter
of 13 mm in the yoke serves for fastening a clamp (or a spigot) to the yoke.
Note: the spigot has to be inserted into the oor stand and always secured.
3.2 Connecting the pixelPATT with the PATT Driver
1. Disconnect the PATT Driver from mains.
2. Connect the pixelPATT to the PATT Driver by means of the 4-pin data cable.
3. Connect the PATT Driver to mains and make desired setting.
ALWAYS DISCONNECT THE PATT DRIVER FROM MAINS BEFORE CONNECTING/DISCONNECTING
THE PIXELPATT.
6
4. Technical specications
Input voltage: 48V
Max. power consumption: 210W
Compatible control driver: PATT Driver
Light source: 7x RGBW LED multichip
LED life expectancy: min. 20 000 hours
Typical lumen maintenance: 70% @ 20 000 hours
Optical System: 7 x 200 mm parabolic aluminium reector with high reectivity coating
Control input: Locking 4-pin XLR (male)
Max. length of cable between
PATT Driver and pixelPatt: 10m
Mounting Points: Mounting horizontally or vertically via mounting yoke (360° tilt range)
Rigging: M12 mounting for clamp or spigot.
Operation position: any
Ingress protection: IP20 (for dry location only)
Weight: 12 kg
Max. surface temperature: 65°C (at 45°C ambient)
Maximum ambient temperature: 45 °C
Total heat dissipation (calculated):716 BTU
Min. distance from ammable surfaces: 0.2 m
Min. distance of illuminated objects: 0.2 m
Dimensions (mm)
Wiring of control input:
Optional accessories
Tripod for PATT 2013/2017, pixelPATT (P/N 10980374)
Floor Stand for PATT 2013 (P/N 1098 0259)
Spigot for PATT 2013 (P/N 1098 0260)
1 - 0V
2 - Signal 3- Signal +
4- +48V
7
Beam distribution
October 5, 2017
Specications are subject to change without notice.
Made in ROBE Lighting s.r.o., Palackého 416, 757 01 Valašské Meziříčí, Czech Republic
Loading...