Robe Color Wash 575 AT Zoom AT series User Manual
1
Version 1.4
2
Table of contents
1. Safety instructions ......................................................................................................... 3
2. Operating determinations .............................................................................................. 4
3. Description of the device ............................................................................................... 5
4. Installation....................................................................................................................... 6
4.1Fitting the lamp ............................................................................................................6
4.2 Lamp adjustment .......................................................................................................7
4.3 Inserting/Exchanging colours ....................................................................................7
4.4 Connection to the mains ............................................................................................8
4.5 Changing the power supply settings .......................................................................... 8
4.6 Changing the front lens .............................................................................................9
4.7 Installing top hats ...................................................................................................... 9
4.8 Rigging the xture .................................................................................................... 10
4.9 DMX-512 connection/connection between xtures ..................................................12
5. ColorWash 575 AT Zoom-DMX Protocol-version 1.0 ................................................ 13
6. Controller mode ........................................................................................................... 16
6.1 DMX addressing .......................................................................................................16
6.2 Remotely controllable functions ............................................................................... 16
7. Stand - alone mode ......................................................................................................17
8.Control menu map ......................................................................................................... 18
9. Control menu ............................................................................................................... 21
9.1 Fixture Address .......................................................................................................21
9.2 Slave control ...........................................................................................................
21
9.3 Fixture informations ..................................................................................................21
9.4 Personality ...............................................................................................................23
9.5 Lamp On/Off ............................................................................................................24
9.6 Manual mode ...........................................................................................................24
9.7 Test sequences ........................................................................................................ 25
9.8 Stand-alone setting ................................................................................................. 25
9.9 Reset function .......................................................................................................... 26
9.10 Special functions ....................................................................................................26
10. Low power mode ........................................................................................................ 27
11. Error and information messages .............................................................................. 27
12. Technical specications ............................................................................................ 29
13. Maintenance and cleaning ......................................................................................... 31
ColorWash 575 AT Zoom
3
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOU INITIAL START - UP!
1. Safety instructions
Every person involved with installation and maintenance of this device have to:
- be qualiled
- follow the instructions of this manual
CAUTION!
Be careful with your operations.
With a high voltage you can suffer
a dangerous electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
Important:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
Never let the power-cord come into contact with other cables! Handle the power cord and all connections with
the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear panel.
Always plug in the power plug least. Make sure that the power-switch is set to OFF-position before you connect
the device to the mains. The power plug has to be accessable after installing the device.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the powercord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the powercord by the plug. Never pull out the plug by tugging the power cord.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to
earth.
The electric connection, repairs and servicing must be carried out by a qualied employee.
Do not connect this device to a dimmer pack.
Do not switch the xture on and off in short intervals as this would reduce the lamp’s life.
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!
For replacement use lamps and fuses of same type and rating only.
CAUTION ! EYEDAMAGES !
Avoid looking directly into the light source
(meant especially for epileptics) !
4
2.Operating determinations
This device is a moving-head for creating decorative effects and was designed for indoor use only.
If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.
Never run the device without lamp!
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the xture by holding it at the projector-head, as the mechanics may be damaged. Always hold the
xture at the transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture
or dust. There should not be any cables lying around. You endanger your own and the safety of others!
The minimum distance between light output and the illuminated surface must be more than 2 meters.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.
Always x the xture with an appropriate safety rope. Fix the safety rope at the correct holes only.
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fas-
tened.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge lamps may
explose and emit a high ultraviolet radiation, which may cause burns.
The maximum ambient temperature 40°C must never be exceeded. Otherwise, the lamp is switched off and
the xture is out of operation for 5 minutes.
CAUTION!
The lens has to be replaced when it is obviously damaged,
so that its function is impaired, e. g. due to cracks or deep scratches!
Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the device. Most damages are the result of unprofessional operation!
CAUTION!
The lamp has to be replaced when it is damaged
or deformed due to the heat!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modications on the device are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like shortcircuit, burns, electric shock, burns due to ultraviolet radiation, lamp explosion, crash etc.
5
3. Description of the device
1 - Front lens
2 - Moving head
3 - Yoke
4 - Base
Rear panel:
5 - Power switch
6 - Power cord
7 - Fuse holder
8 - 3-pin DMX output
9 - 3-pin DMX input
10 - 5-pin DMX output
11 - 5-pin DMX input
Front panel:
12 - Mode-button
13 - Enter-button
14 - Up-button
15 - Down-button
16 - Display
6
4. Installation
4.1Fitting the lamp
DANGER !
Install the lamps with the device switched off only.
Unplug from mains before !
To insert the lamp loosen the lamp cover at the rear of head (see the drawings ) by remowing the 3 fastening
screws which are marked "X,Y,Z".Carefully pull out the cover with the lamp socket assembly.If changing the
lamp, remove the old lamp from the socket. Insert the lamp to the socket.
Do not install a lamp with a higher wattage! A lamp like this generates temperatures the device is not designed for.Damages caused by non-observance are not subject to warranty. Please follow the lamp manufacturer‘s notes!Do not touch the glass-bulb with bare hands during the installation! Make sure that the lamp
is installed tightly into the lampholder system.
Reclose the lamp cover and tighten the 3 screws.
Before striking the lamp, reset the "LAti"and "LASt" counter s in menu "InFO", by pressing the "Up" and
"Down" buttons in one time and then conrming with the Enter-button.
Do not operate this xture with opened housing-cover!
3 fastening screws "X,Y,Z"
Lamp cover
Lamp cover
7
4.2 Lamp adjustment
The ColorWash 575 AT Zoom lamp holder is aligned at the factory. Due to differences between lamps, ne
adjustment may improve light performance.
Strike the lamp,open the shutter and set the dimmer intensity onto 100% and aim the light on a at surface
(wall).Center a hot-spot(the brightest part of the image) by using the 3 adjustment screws "A,B,C".Turn one
screw after another a quarter-turn clokwise(counter-clokwise) to set the hot-spot in the center of the image.If
you cannot detect the hot-spot,adjust the lamp until the light is evenly distributed.
4.3 Inserting/Exchanging colours
DANGER!
Install the colours with the device switched off only.
Unplug from mains before!
If you wish to change colours ,open the top cover of the head by loosening 4 quarter-turn fasteners on the top
cover.
Gently bend out the colour module to release it from the 3 distance slots and eject it from the pressing snap.
Put the new colour module back under the pressing snap and push it to the distance slots.
3 adjustment screws "A,B,C"
colour-module
pressing snap
8
4.4 Connection to the mains
Verify the power supply settings before applying power!
If you wish to change the power supply settings,see the chapter below.
Connect the xture to the mains with the power cord.
If the plug on the exible cord is not the right type for your socket outlets,do not use an adaptor,but remove the
plug from the cord and discard.Carefully prepare the end of the the supply cord and t a suitable plug.
The earth has to be connected!
Do not connect the xture to a dimmer system!
The occupation of the connection-cables is as follows:
Cable (EU) Cable (US) Pin International
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth
4.5 Changing the power supply settings
Both the transformer and the ballast must be connected correctly for the local AC voltage and frequency.
The wrong settings can cause poor performance or demage of the moving head.The factory settings are printed
next to the power switch.
If you want to change the power supply settings,follow the instructions:
1.Disconnect the xture from AC power.
2.Remove the top base covers by loosening the 12 fastening screws.
3.Move the wire 1 on the transformer connection block to the position according to the desired voltage.
4.Move the wires 2 and 3 on the ballast connection block to the position according to the desired frequency
(voltage).
5.Close the base before applying AC power.
Examples:
EU-version: US-version:
9
4.6 Changing the front lens
The ColorWash 575 AT Zoom is supplied with Fresnel lens as a standard front lens.If you wish to extend the
zoom range,you may need optional front wide-angle lens D200.
Front lens: Beam angle:
Standard Fresnel lens 8°-50°
Front wide-angle lens 87°
Switch the device off before changing the lens.Be careful.Front lens is heavy!
Changing the front Fresnel lens:
1.Remove the front lens module using a athead screwdriver to unlock the four quarter-turn screws.
2.Unscrew the safety cabel from the lens holder
3.Screw up the safety cable to the module of front wide-angle lens D200.
4.Place the module and fasten it by locking the four quarter-turn screws.
4.7 Installing top hats
The ColorWash 575E AT Zoom can be tted with various types of the top hats-see chapter "Technical specications".If you wish to install a top hat (optional), follow the instructions:
Switch the device off before installing the top hat!
Installing the top hat on the front lens-holder of the xture:
1.Put desired top hat onto a front lens-holder and fasten it by two fastening screws.
2.Secure the top hat by means of two securing springs (hook rst tip of the spring to the plastic projection in
the front lens-holder and the second one snap to the slot in the top hat).
Quarter-turn screws
Q u a r t e r - t u r n
screws
Nut
Bolt
Safety cable
Slot
Securing spring
Plastic projection
Securing spring
Top hat
Fastening screw
Fastening screw
Lens-holder
10
4.8 Rigging the xture
DANGER TO LIFE!
Please consider the respective national norms during the installation!
The installation must only be carried out by an authorized dealer!
The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for
1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net.
This secondary safety attachment must be constructed in a way that no part of the installation can fall down if
the main attachment fails.
When rigging, derigging or servicing the xture staying in the area below the installation place, on bridges,
under high working places and other endangered areas is forbidden.
The operator has to make sure that safety-relating and machine-technical installations are approved by an expert
before taking into operation for the rst time and after changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations are approved by an
expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled
person once a year.
The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)
calculating working load limits, installation material being used, and periodic safety inspection of all installation
material and the projector. If you lack these qualications, do not attempt the installation yourself, but instead use
a professional structural rigger. Improper installation can result in bodily injury and.or damage to property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing systems have to be used.
The projector must never be xed swinging freely in the room.
Caution: Projectors may cause severe injuries when crashing down! If you have doubts concerning the safety
of a possible installation, do NOT install the projector!
Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector’s
weight.
Danger of re !
When installing the device, make sure there is no highly inammable
material (decoration articles, etc.) in a distance of min. 0,7 m.
CAUTION!
Use 2 appropriate clamps to rig the xture on the truss.
Follow the instructions mentioned at the bottom of the base.
Make sure that the device is xed properly! Ensure that the
structure (truss)to which you are attaching the xtures is secure.
The projector can be placed directly on the stage oor or rigged in any orientation on a truss without altering
its operation characteristics .
Loading...