Robe ClubWash 250CT, clubwash 300 CT User Manual
1
Version 1.1
2
Table of contents
1. Safety instructions ......................................................................................................... 3
2.Operating determinations ............................................................................................... 4
3. Description of the device ............................................................................................... 5
4. Installation....................................................................................................................... 6
4.1Fitting the lamp ............................................................................................................6
4.2 Lamp adjustment .......................................................................................................7
4.5 Connection to the mains ............................................................................................7
4.6 Changing the power supply settings-magetic ballast .................................................7
4.7 Manual zoom ..............................................................................................................9
4.7 Rigging the xture .................................................................................................... 10
4.8 DMX-512 connection/connection between xtures ..................................................13
5.ClubWash 250-DMX Protocol-version 1.0 .................................................................. 14
6. Controller mode ........................................................................................................... 15
6.1 DMX addressing .......................................................................................................15
6.2 Remotely controllable functions ...............................................................................
15
7. Stand - alone mode ......................................................................................................16
8.Control menu map ......................................................................................................... 17
9. Control menu ............................................................................................................... 19
9.1 Fixture Address .......................................................................................................19
9.2 Slave control ...........................................................................................................19
9.3 Fixture informations .................................................................................................. 19
9.4 Personality ...............................................................................................................20
9.5 Lamp On/Off ............................................................................................................21
9.6 Test sequences ........................................................................................................ 21
9.7 Stand-alone setting ................................................................................................. 22
9.8 Reset function .......................................................................................................... 22
9.9 Special functions ......................................................................................................23
10. Error and information messages .............................................................................. 24
11. Technical specications ............................................................................................ 25
12. Maintenance and cleaning ......................................................................................... 27
ClubWash 250 CT
3
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOU INITIAL START - UP!
1. Safety instructions
Every person involved with installation and maintenance of this device have to:
- be qualiled
- follow the instructions of this manual
CAUTION!
Be careful with your operations.
With a high voltage you can suffer
a dangerous electric shock when touching the wires!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes
written in this manual.
Important:
The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual
or any unauthorized modication to the device.
Please consider that damages caused by manual modications to the device are not subject to warranty.
Never let the power cord come into contact with other cables! Handle the power cord and all connections with
the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear panel.
Always plug in the power plug least. Make sure that the power switch is set to OFF-position before you connect
the device to the mains. The power plug has to be accessable after installing the device.
Make sure that the power cord is never crimped or damaged by sharp edges. Check the device and the power
cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the power-
cord by the plug. Never pull out the plug by tugging the power cord.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to
earth.
The electric connection, repairs and servicing must be carried out by a qualied employee.
Do not connect this device to a dimmer pack.
Do not switch the xture on and off in short intervals as this would reduce the lamp’s life.
During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily
mean that the device is defective.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!
For replacement use lamps and fuses of same type and rating only.
CAUTION ! EYEDAMAGES !
Avoid looking directly into the light source
(meant especially for epileptics) !
4
2.Operating determinations
This device is a moving-head for creating decorative effects and was designed for indoor use only.
If the device has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation water might damage your device. Leave the device switched off until
it has reached room temperature.
Never run the device without lamp!
Do not shake the device. Avoid brute force when installing or operating the device.
Never lift the xture by holding it at the projector-head, as the mechanics may be damaged. Always hold the
xture at the transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to extreme heat, moisture
or dust. There should not be any cables lying around. You endanger your own and the safety of others!
The minimum distance between light-output and the illuminated surface must be more than 1.3 meters.
Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.
Always x the xture with an appropriate safety-rope. Fix the safety-rope at the correct holes only.
Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fas-
tened.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as discharge lamps may
explose and emit a high ultraviolet radiation, which may cause burns.
The maximum ambient temperature must never be exceeded. Otherwise, the lamp is switched off and the
xture is out of operation for 5 minutes.
CAUTION!
The lens has to be replaced when it is obviously damaged,
so that its function is impaired, e. g. due to cracks or deep scratches!
Operate the device only after having familiarized with its functions. Do not permit operation by persons not
qualied for operating the device. Most damages are the result of unprofessional operation!
CAUTION!
The lamp has to be replaced when it is damaged
or deformed due to the heat!
Please use the original packaging if the device is to be transported.
Please consider that unauthorized modications on the device are forbidden due to safety reasons!
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-
circuit, burns, electric shock, burns due to ultraviolet radiation, lamp explosion, crash etc.
5
3. Description of the device
1 - Moving head
2 - Fresnel lens
3 - Yoke
4 - Base
Rear panel:
5 - Power switch
6 - Fuse holder
7 - Power cord
8 - 3-pin DMX input
9 - 3-pin DMX output
Front panel:
10 - Display
11 - Mode-button
12 - Enter-button
13 - Up-button
14 - Down-button
6
4. Installation
4.1Fitting the lamp
DANGER !
Install the lamps with the device switched off only.
Unplug from mains before !
To insert the lamp BA 250/2 SE open the lamp cover on the back of the projector head by loosening the 3
fastening screws marked X,Y,Z on the cover.
If changing the lamp, remove the old lamp from the socket. Insert the lamp to the socket.
Do not install a lamp with a higher wattage! A lamp like this generates temperatures the device is not designed
for.
Damages caused by non-observance are not subject to warranty. Please follow the lamp manufacturer‘s notes!
Do not touch the glass bulb with bare hands during the installation! Make sure that the lamp is installed tightly
into the lampholder system.
Reclose the lamp cover and tighten the 3 quarter-turn fasteners.
Before striking the lamp, reset the “LAti/rSEt” and “LASt/rSEt”counters in the “InFO” menu on the control
panel, by pressing the “Up” and “Down” buttons in one time and then conrming with the “Enter”-button.
Do not operate this xture with opened housing-cover!
Lamp cover
Fastening screws
7
4.2 Lamp adjustment
The lampholder is aligned at the factory. Due to differences between lamps, ne adjustment may improve light
performance.
Strike the lamp, cancel all effects, open the shutter and set the dimmer intensity onto 100 % and focus the light
on a at surface (wall) or use function “LAAd” in the Special functions .Center the hot-spot (the brightest part
of the beam) using the 3 adjustment screws „A, B, C”. Turn one screw at a time to drag the hot-spot, diagonally
across the projected image. If you cannot detect a hot -spot, adjust the lamp until the light is even.
To reduce a hot-spot, pull the lamp in by turning all three screws „A, B, C” clockwise 1/4-turn at a time until the
light is evenly distributed.
If the light is brighter around the edge than it is in the center, or if light output is low, the lamp is too far back in
the reector. „Push” the lamp out by turning the screws „A, B, C” counterclockwise 1/4-turn at a time the light
is bright and evenly distributed.
4.5 Connection to the mains
Verify the power supply settings before applying power!
If you wish to change the power supply settings,see the chapter below.
Connect the xture to the mains with the enclosed power plug.If you need to install other power plug on the
power cable,follow the identication table below.
The earth has to be connected!
Do not connect the xture to a dimmer system!
The occupation of the connection-cables is as follows:
Cable (EU) Cable (US) Pin International
Brown Black Live L
Light blue White Neutral N
Yellow/Green Green Earth
4.6 Changing the power supply settings-magetic ballast
Both the transformer and the ballast must be connected correctly for the local AC voltage and frequency.
The wrong settings can cause poor performance or demage of the moving head.The factory settings are printed
next to the power switch.
If you want to change the power supply settings,follow the instructions:
1.Disconnect the xture from AC power.
2.Remove the 2 top base covers by loosening 16 screws.
3.Move the wire 1 on the transformer connection block to the position according to the desired voltage.
4.Move the wires 2 and 3 on the ballast connection block to the position according to the desired frequency
(voltage).
5.Close the base before applying AC power.
Screws "A","B","C"
8
Examples:
EU-version:
US-version:
9
4.7 Manual zoom
The lens system can be congured in the range between 8° and 22° beam angles.To set the desired beam
angle, open the front cover of the head by opening the 2 fasteners,loose the 2 adjusting screws on the fresnel
lens unit and adjust the required beam angle.Tighten the adjusting screws and place back the front cover of
the head.
fastener
Fresnel lens
adjusting screw
front cover
Loading...