Roban Bell AH-1W Compactor, AS-350, B212, B412, B 429 Instruction Manual

Bell AH-1W™

Compactor

CompactorCompactor

Compactor

Manual

CCPM SCALE RC HELICOPTER

Compactor 700 Manual – Bell AH-1W™

Release 1.0 - April 2013

Bell, emblems, logos, and body designs are trademarks of Textron Innovations Inc. and are used under license by Roban Ltd.

Roban Limited Dryriver Industrial Zone, Venture Cross Rd. Jiaolian, Wanjiang City District of Dongguan, 523046 Dongguan County (GD) - PRC

SPECIFICATIONS

Body length: 1670mm Length incl. rotors: 1850mm Width: 450mm Height: 480mm Main rotor diameter: 1560mm Main blade length: 700mm Tail rotor diameter: 280mm Tail blade length: 105mm Main shaft diameter: 12mm Tail shaft diameter: 5mm Spindle diameter: 8mm Battery compartment: 120x60x180mm Motor:* 1x 750MX 450KV brushless outrunner, 12S capable Speed controller:* 1x 120A brushless, 12S capable Servo:* 3x metal gear cyclic, 1x 9g metal gear tail servo Battery:* 44.4V 5000mAh 35C+ Flight time: 5 minutes Takeoff weight: 9000g Flight Stabilization:* 3 axis flybarless gyro Radio Control:* min. 6 channel with pitch and throttle curves

*) Optionally available equipment

The Compactor is a high performance radio controlled scale helicopter. Our goal was to create a simple, high performance helicopter, with a minimum of mechanical components and simple maintenance. Please read this user manual carefully, it contains instructions for the correct assembly of the model. Please refer to the web site www.robanmodel.com for updates and other important information. Thank you for your purchase, and have a great time with your Compactor! Roban Limited

IMPORTANT NOTES

*This radio controlled helicopter is not a toy. *This radio controlled helicopter can be very dangerous. *This radio controlled helicopter is a technically complex device which has to be built and handled very carefully. *This radio controlled helicopter must be built following these instructions. This manual provides the necessary information to correctly assemble the model. It is necessary to carefully follow all the instructions. *Inexperienced pilots must be monitored by expert pilots. *All operators must wear safety glasses and take appropriate safety precautions. *A radio controlled helicopter must only be used in open spaces without obstacles, and far enough from people to minimize the possibility of accidents or of injury to property or persons. *A radio controlled helicopter can behave in an unexpected manner, causing loss of control of the model, making it very dangerous. *Lack of care with assembly or maintenance can result in an unreliable and dangerous model.

*Neither Roban Limited nor its agents have any control over the assembly, maintenance and use of this product. Therefore, no responsibility can be traced back to the manufacturer. You hereby agree to release Roban Limited from any responsibility or liability arising from the use of this product.

SAFETY GUIDELINES

*Fly only in areas dedicated to the use of model helicopters. *Follow all control procedures for the radio frequency system. *It is necessary that you know your radio system well. Check all functions of the transmitter before every flight. *The blades of the model rotate at a very high speed; be aware of the danger they pose and the damage they may cause. *Never fly in the vicinity of other people.

NOTES FOR ASSEMBLY

Please refer to this manual for assembly instructions for this model. Follow the order of assembly indicated. The instructions are divided into chapters, which are structured in a way that each step is based on the work done in the previous step. Changing the order of assembly may result in additional or unnecessary steps. Use thread lockers and retaining compounds as indicated. In general, each bolt or screw that engages with a metal part requires thread lock. Factory pre-assembled components have been assembled with all the required thread lock and lubricants, and have passed quality control. It is not necessary to disassemble and re-assemble them. We do not recommend the use of thin cyanoacrylate glue for surface mount of painted parts. The fumes of the curing glue leave white stains on the clear coat, which are hard to remove.

1 – Tail gearbox

2 – Tail tube short

3 – Tail shaft short

4 – Ball links

5 – Tail boom holder

6 – Main frame assy

7 – Motor pulley

8 – Tail rod short

9 – Tail rotor assy

10 – Main rotor assy

11 – Tail servo holder

12 – Tail shaft bearings

13 – Tail servo frame

14 – Tail sero rod guides

15 – Main rotor blades

16 – Tail shaft long

17 – Tail tube long

18 – Tail rod long

19 – Tail boom supports

20 – Blade linkages

21 – Tail blades 2pcs

22 – Landing gear 1 set

23 – Tail strut

24 – Weapon winglets 2pcs

25 – Wing tip 2 pcs

26 – Holder 2pcs

27 – Missile stations 2pcs

28 – Missile pods 2pcs

29 – Anti IR 2pcs

30 – Tail wings

31 – Gatling gun 2pcs

32 – Cockpit mainframe 1pc

33 – Instrument panel 1pc

34 – Pitch stick 1pc

35 – Control stick 1pc

36 – Target monitor 1pc

CONTENTS:

37 – Control stick 1pc

38 – Rudder pedals 1pc

39 – Scale part 1pcs

40 – Chairs 2pcs

41 – Screw A2x24 4pcs

42 – Screw A2x14 4pcs

43 – Screw M3x14 2pcs

44 – Screw A3x16 4pcs

45 – Washer M3 6pcs

46 – Washer M4 4pcs

47 – L Brackets 4pcs

48 – Screw M10x4 4pcs

49 – Nut M3x10 6pcs

50 – Self locking Nut M3

51 – Ball links 4pcs

52 – Self lock Nut M2 4pcs

53 – Self lock nut M4 1pc

54 – Wooden washer 6pc

55 – Screw A1.7x7 6pcs

56 – Scale part A 1pc

57 – Scale part B 1pcs

58 – Scale part C 1pc

59 – Scale part D 1pc

60 – Scale part E 1pc

61 – Scale part F 2pcs

62 – Scale part G 2pcs

63 – Scale part H 1pc

64 – Scale part I 2pcs

65 – Carbon rod 4x115 1pc 66 – Scale part D 1pc

67 – Scale part D 1pc

68 – LED wire red 1pc

69 – Led wire green 1pc

70 – LED wire red 1pc

71 – 12mm light cap 1pc

72 – LED controller 1pc

73 – Decal set 1pc

ADDITIONAL COMPONENTS REQUIRED

*Electric Motor: 10S-12S – 400-600Kv, pinion shaft diameter 6mm *Speed controller: minimum 120A to be safe *Batteries: 10-12S 4000-5000mAh *1 flybarless 3 axis control unit, suitable for scale flying *Radio power system *3 cyclic servos *1 tail rotor servo *6 channel radio control system on 2.4 GHz

TOOLS, LUBRICANTS, ADHESIVES

*Generic pliers *Hexagonal driver, size 1.5, 2, 2.5, 3, 4mm *4mm T-Wrench *5.5mm Socket wrench (for M3 nuts) *8mm Hex fork wrench (for M5 nuts) *Medium threadlocker (eg. Loctite 243) *Strong retaining compound (eg. Loctite 648) *Spray lubricant (eg. Try-Flow Oil) *Synthetic grease (eg. Tri-Flow Synthetic Grease) *Cyanoacrylate adhesive *Pitch Gauge (for set-up) *Soldering equipment (for motor wiring)

Inside the main box there are:

Inside the main box:

Bag 1: Scale Decals Box 2: Mechanics Box 3: Scale Cockpit Box 4: Boom, Blades, Tail blades, Rods

Assembly Scale Fuselage

Prior to installing the mechanics into the fuselage, please prepare the fuselage according to the following steps. installation into the fuselage most of the helicopter mechanic become inaccessible.

Remove the hatch as shown.

Secure the landing gear using screws (41) as shown.

Install light (68) in wing end with glue.

Install the holder (26) with screws (42) onto the wing (24).

Install the tail landing gear (22) as shown.

Install light and housing (70, 71) as shonw using glue.

Install light (69) in wing end with glue.

Install the wingtip to the wing using epoxy glue.

Glue the rocket pod on with epoxy glue.

Glue the Anti-IR unit on with epoxy glue

Glue the tail distancer in with epoxy glue

Glue the rocket launcher on with epoxy glue.

Install the winglets onto the main fuselage.

Assembly Mechanics

The mechanics are almost entirely preassembled and split up into four sections: rotorhead, main frame, tail frame and tail tube. Prior to the installation into the scale fuselage, the mechanics have to be entirely assembled, electronic components installed, adjusted and tested. After installation into the fuselage most of the helicopter mechanic become inaccessible.

Step 1 – Rotorhead

Slide the rotorhead onto the main shaft. Use screw (70-

00006) and nylon nut (70-00007) to secure the rotorhead onto the main shaft. Use two screws (70-00008) to additionally clamp up the rotor hub onto the shaft as shown.

Make sure the distance between the ball link and the L lever is equally at 24mm. Finally snap on the ball links (70-00025) on the swashplate’s upper disc uni-links (70-00030).

Step 2 – Tail boom

First of all install the center bearings (70-00100) with the holders (02-02006) into the tail boom (70-00095). Distribute the bearings evenly in the tail boom. It is recommended to apply a bit of lubrificant onto the tubes inner surface, elsewise the bearing is likely to get stuck before the correct position is reached. Then install the center support ring (600UH1-007), the servo rod guides (70-00040) and the servo two tail servo holders (70-00098). Install the tail torque tube (70-00096) into the tail tube.

Then insert the tail boom into the tail boom holders (7000093, 70-00094). Lock the tube in place with screw M3x8 (70-00086) via the clamp up and additionally with screw M3x6 (70-00053) as shown. Install the carbon support beams (70-00104-70-00106) on the main frame and the tail boom tail boom clamp (600UH1-007).

Step 3 – Tail Servo Installation

First of all, mount the holder frame (70-00097) onto the boom holders (70-00098) using screw M3x8. Then mount the tail servo of your choice into the tail frame using screws M3x10, washers and nylon nuts as shown. Install the servo horn and the supplied uniball. Then slide the tail rotor control rod (70-00103) into the four guides. Install the ball link (70-)

on both ends of the tail rotor control rod. Distribute the guides evenly along the tail boom. Then install the tail rotor frame onto the tail boom. Lock it with the three screws as shown, but do not use thread lock yet, as it has got to be uninstalled again. Snap the servo control rod onto the ball link.

Step 4 – Cyclic Servo Installation

Install the three cyclic servos onto the servo tray as shown. Depending on your servos, you may have to use washers to adjust the servo to the proper installation height. It is strongly recommended to use metal servo horns and only metal geared servos. The multi blade rotor head can feedback forces that may lead to failure of plastic components.

After the servos are installed, you will have to adjust the linkage rods length’s according to the schematics below. The distances are uniball center to uniball center:

1=81mm 2=112mm 3=81mm

Step 5 – Adjust swashplate linkages

The linkages from the L-Levers to the swash plate have to be set at correct length. Distances are uniball center to uniball center: 1=35mm

Step 6 – Motor and Belt installation

In order to install the motor, you must first disassemble one of the side frames in order to have access to the mounting screws and access to the belt drive. Hence one side frames fasteners are not tightened upon delivery. Before installing the pinion pulley on the motor, you have to add a flat to the motor shaft in order to secure the pulley with the set screws (70-).

Mount the motor as shown using washers and screws onto the motor mount (70-00066). Make sure to have the motor wire outlet facing into the right direction for connecting them to the ESC. Then insert the belt pulley into the belt and slide it onto the motor shaft. Before you tighten the set screws, make sure that the pinion is installed leveled with the belt pulley, the distance (Fig. 1) is at 24.5mm. Use both tensioning screws to tension the belt drive. The belt mustn’t be tensioned too tight to avoid unnecessary wear. After installation of the motor, reassemble the side frames.

1

Step 7 – Electrical Wiring and Setup

The mechanics have to be fully electrically setup and adjusted prior to installation into the fuselage. As the use of a 12S (44.4V) setup is necessary, we strongly recommend to run the control equipment on a separate 2S Lipo battery and BEC for security reasons.

In scale configurations main battery power wires may be longer than on comparable 3D helicopter equipment. As HV ESCs do not necessarily have the main battery ground wire connected to the servo signal ground wire, it may be necessary to create an additional connection between the BEC 2S batteries ground wire and the 12S main battery ground wire. Certain configurations without this ground interconnection have led to a loss of signal at the ESC from the receiver due to EMC effects.

The swash plate is a regular 120deg CCPM type, please take your time to adjust all servo travels, center positions – the entire 3 axis gyro – servo – radio setup prior to the installation into the fuselage.

A 450KV motor such as the Align 750MX run at app. 80% throttle (hover) shows satisfying results. As space is limited, please make sure you check the dimensions if you intend to use other brand motors.

In regards to the gyro setup, we recommend to start with standard values of the 3 axis gyro. Make sure you install the gyro in a way that provides easy access for connecting your programming equipment. As the scale fuselage adds additional inertia to each axis, gyros are normally to be set at a lower gyro gain. All in all, a rigid gyro response does ruin the scale look in flight.

Before operating the model check the following points:

-The direction of servo rotation (including the throttle function) and travels.

-The direction of effect of the gyro, and the transmitter mixer functions you have programmed.

-Collective pitch travel (linear travel -2/-3° to +9/+10°)

ATTENTION !

When using the a pitch gauge to adjust correct CP travels, make sure that the gauge lines up with the flat surface of the rotor blade. Many pitch gauges do not show the correct

angle when snapped onto unsymmetric rotor blades!

The main rotor blades are not symmetrical. Do not try to fly inverted.

- It is permissible to reduce servo travels, but not below 60% (in this case adjust the mechanical linkage); travels should be primarily symmetrical.

- Apply collective pitch min. / collective pitch max. and full roll and pitch-axis commands simultaneously in all directions; rotate the rotor head at the same time, and check that at the extremes of travel no part of the rotor head is obstructed.

- The auto-rotation switch must be assigned, and within easy reach!

- When auto-rotation is selected: throttle position to off, all directions of control and travels as in normal flight, tail rotor to 0° = fixed value.

-The first few batteries should be flown with the model close to the ground, i.e. no more than about 1 m altitude, until you are confident that there are no defects or errors, and that everything is working faultlessly:

- Use your ears critically (!), listening for unusual sounds and vibration, and seek out the problem if you are in any doubt at all!

- Don’t listen to anyone standing close by if they try to hurry you into flying the model.

- Avoid hovering outside ground effect (hover altitude with a model: approx. 1m, or half the rotor disc diameter):

- Hovering requires very high power, and you are completely dependent on the motor: in contrast to most full-size helicopters, model helicopters have only one (!) power plant.

Step 8 – Installation of mechanics

Mount the four L-brackets (60UH1-003) onto both sides of the main frame as shown. Make sure they are properly aligned before you fasten the screws.

Unmount the entire tail rotor frame from the tail box again.

Install the mechanics by sliding them into the fuselage as shown.

Install the tail boom.

Mount the tail boom onto the front fuselage using screws (55) and wooden washers (54).

Install the rod ends on the lever triangle.

Use the holes in the fuselage to tighten the tail frame screws.

Use screws (43) and washers (45) to secure the mechanic.

Install the short tail boom in the tail frame.

Install the washer (66) as shown.

Install EVA distancers (67) as shown using glue.

Close the tail hatch with the screws.

Slide the tail wings onto the rods and tighten screws.

Glue lever 39 in as shown.

Glue pedals (38) in as shown.

Install the carbon rod (65) as shown.

Install the gun (31) with Nyloc Nut M4 (53) as shown.

Glue lever 35 in as shown.

Glue pitch lever (34) in as shown.

Glue lever (35) in as shown.

Glue instrument panel (33) in as shown.

Glue lever 39 in as shown.

Glue pedals (38) in as shown.

Glue instrument panel (36) in as shown.

Glue seats (40) in as shown.

Then install the cockpit into the canopy, use glue

Install the canopy on the helicopter as shown.

Please install the scale parts as depicted using epoxy glue!

Finally connect the LED controller to the LEDs you installed.

Step 10 - Battery installation

The battery compartment consists of a convenient and secure wooden structure. Open the hatch first, then secure the batteries in position by using velcros as shown.

Step 11 - Now it is time to fly

For the first few circuits: starting from ground effect, accelerate to a moderate speed in level flight, and only then initiate a climb, always keep the model flying at a brisk forward speed; on the landing approach always descend towards the landing area at a steady angle (around 45°) directly into wind, and don’t bring the model to a halt until it is in ground effect again. This way you can save your model through autorotation. If one particular technical fault keeps recurring in your model, replacing the component concerned will not solve the problem unless you change some other aspect of the operating conditions. It is as hard to fly nice and smooth scale maneuvers as flying F3C or exact 3D figures.

And one final request: Please be realistic when assessing your piloting skills, because a scale helicopter is heavy and hence much less agile in response than any 3D helicopter. Keep this comparison in mind: if you can’t swim and you dive into deep water, the chances are that you will drown.

Appendix A – Explosion Drawings

Appendix B – Spareparts

Appendix C – Sparepart List

RCH-70-001 1-JJ-70-00147

Sideframes

Seitenrahmen

1-JJ-70-00148

Aft frame

hintere Platte

1-JJ-70-00149

Bottom frame

Bodenplatte

1-JJ-70-00150

Fwd frame

vordere Platte

RCH-70-002 1-JJ-70-00099

Distancer 6x62

Distanzstück

6x62

11-600UH1

-

003 L-Bracket

L-

Halter

RCH-70-003 1-JJ-70-00152

Landing Gear

Fahrwerk

RCH-70-004 1-JJ-70-00153

Footrest

Trittleiste

RCH-70-005 1-JJ-70-00058

Upper base plate

Obere Basisplatte

RCH-70-006 1-JJ-70-00071

Lower base plate

Untere

Basisplatte

RCH-70-007 1-JJ-70-00066

Motor holder

Motorhalter

1-JJ-70-00067

Screw M3x30

Schraube M3x30

RCH-70-008 1-JJ-70-00062

Main Gear 78T

Hauptzahnrad 78T

RCH-70-009 1-JJ-70-00061

Main gear hub

Hauptzahnradaufnahme

RCH-70-010 1-JJ-70-00063

Spur

Gear 20T

Ritzel 20T

RCH-70-011 1-JJ-70-00075

Washer 10x12x0.5

Beilagschreibe

10x12x0.5

1-JJ-70-00076

Bearing 10x15x5

Kugellager 10x15x4

1-JJ-70-00077

One way bearing 10x14x12

Kugellager 10x14x12

1-JJ-70-00078

Belt pulley 78T

Riemenrad 78T

1-JJ-70-00079

Washer 10x12x1

Beilagscheibe 10x12x1

RCH-70-012 1-JJ-70-00080

Gear 1M 36T

Zahnrad 1M 36T

RCH-70-013 1-JJ-70-00082

Gear hub 36T

Zahnradaufnahme 36T

RCH-70-014 1-JJ-70-00083

Gear holder 30T

Zahnradaufname 30T

RCH-70-015 1-JJ-70-00073

Belt

pinion 22T

Riemenscheibe 22T

RCH-70-016 1-JJ-70-00037

Ball link 5mm

Kugelkopfrahmen 5mm

1-JJ-70-00038

Lever 1

Hebel 1

1-JJ-70-00039

Flanged bearing 3x7x3

Kugellager Flansch

3x7x3

RCH-70-017 1-JJ-70-00060

Distancer 10x25.1

Abstandshalter 10x25.1

RCH-70-018 1-JJ-70-00074

Collar 12mm

RCH-70-019 1-JJ-70-00033

Main Shaft 12mm

Hauptwelle 12mm

RCH-70-020 1-JJ-70-00057

Shaft 10x76.1

Welle 10x76.1

RCH-70-021 1-JJ-70-00026

Ball joint 22mm

Kugelgelenk 22mm

1-JJ-70-00027

Swash upper ring

Taumelscheibe

Oberteil

1-JJ-70-00028

Bearing 30x42x7

Kugellager 30x42x7

1-JJ-70-00029

Swash lower ring

Taumelscheibe

Unterteil

1-JJ-70-00030

Ball head

Kugelkopf

1-JJ-70-00031

Washer 2x8x1

Beilagscheibe 2x8x1

1-JJ-70-00032

Screw M2x6

Schraube M2x6

RCH-70-022 1-JJ-70-00003

Rotorhead top

Rotorkopf oben

1-JJ-70-00004

Rotorhead bottom

Rotorkopf unten

RCH-70-023 1-JJ-70-00001

Rotorhead Cap

Rotorkopfkappe

RCH-70-024 1-JJ-70-00017

Grip Spindle

Blattlagerwelle

RCH-70-025 1-JJ-70-00020

Washer 3x9x1.5

Beilagscheibe

3x9x1.5

1-JJ-70-00021

Bearing 3x7x3

Kugellager 3x7x3

1-JJ-70-00022

Washer 3x4.5x1.1

Beilagscheibe 3x4.5x1.1

1-JJ-70-00023

L-

Lever

L-

Hebel

1-JJ-70-00019

Screw M3x25

Schraube M3x25

1-JJ-70-00018

Self Locking Nut M3

Stoppmutter M3

RCH-70-026 1-JJ-70-00024

Screw M2.5x16

Schraube M2.5x16

1-JJ-70-00025

Ball link 5mm

Kugelkopf 5mm

RCH-70-027 1-JJ-70-00012

Washer 4x8x1

Beilagscheibe 4x8x1

1-JJ-70-00014

Washer 8x14x0.5

Beilagscheibe 8x14x0.5

1-JJ-70-00016

Washer 8x11.5x1.3

Beilagscheibe

8x11.5x1.3

RCH-70-028 1-JJ-70-00009

Main Blade Grip

Hauptrotorblatthalter

RCH-70-029 1-JJ-70-00034

Lever 23mm

Gestänge 23mm

1-JJ-70-00035

Lever 67mm

Gestänge 67mm

1-JJ-70-00036

Gestänge 98mm

RCH-70-030 1-JJ-70-00046

Right servo lever

Rechter Servohebel

1-JJ-70-00047

Left servo lever

Linker Servohebel

RCH-70-031 1-JJ-70-00050

Bearing Block

Lagerbock

RCH-70-032 1-JJ-70-00041

Lever 2

Hebel 2

RCH-70-033 1-JJ-70-00042

Lever 3

Hebel 3

RCH-70-034 1-JJ-70-00044

Bushing 5x7x7

Buchse 5x7x7

1-JJ-70-00049

Washer 5x7x1.5

Beilagschreibe 5x7x1.5

1-JJ-70-00051

Shaft 5x62

Welle 5x62

RCH-70-035 1-JJ-70-00064

Servo holder fwd

Servohalter vorne

1-JJ-70-00065

Servo holder aft

Servohalter hinten

RCH-70-036 1-JJ-70-00068

Uniball 5mm

RCH-70-037 1-JJ-70-00088

Bearing block

Lagerbock

RCH-70-038 1-JJ-70-00087

Tail shaft 5x83

Welle 5x83

1-60-WJ-00003

Tube bevel gear

Kegelrad

1-JJ-70-00092

Washer 15x18x1

Beilagscheibe 15x18x1

RCH-70-039 1-JJ-70-00093

Tail boom holder fwd

Heckrohrhalter vorne

1-JJ-70-00094

Tail boom holder aft

Heckrohrhalter hinten

RCH-70-040 1-JJ-70-00095

Tail boom

Heckrohr

RCH-70-041 1-JJ-70-00096

Tail boom shaft

Heckrohrwelle

12-02-02006

Bearing holder

Kugellagerhalter

11-600jRCH

-70-

002

X

Junction

X-

Verbinder

RCH-70-042 1-JJ-70-00097

Tail servo frame

Heckservorahmen

1-JJ-70-00098

Tail servo clamp

Heckservoklammer

RCH-70-043 1-JJ-70-00102

Gear 1M 30T

Zahnrad 1M30T

RCH-70-044 1-JJ-70-00103

Tail pushrod 702mm

Gestänge 702mm

RCH-70-045 1-JJ-70-00104

Tail support holder

Strebenaufnahme

1-JJ-70-00105

Bolt 1.5x7.8

Bolzen 1.5x7.8

1-JJ-70-00106

Tail support rod

Heckstrebe

RCH-70-046 11-600UH1

-

007 Tail support clamp

Heckstrebenklammer

RCH-70-047 1-60-WJ-00010

Washer 5x7x5.7

Hülse 5x7x5.7

1-60-WJ-00011

Washer 5x7x2.1

Beilagscheibe 5x7x2.1

1-60-WJ-00006

Tail shaft 2 blade

Heckwelle 2 Blatt

RCH-70-048 1-JJ-70-00121

Washer 16x18x9.6

Hülse 16x18x9.6

1-60-WJ-00002

Tail frame gear

Kegelrad Heck

RCH-70-049 1-JJ-70-00110

Center hub

Heckrotorkopf

RCH-70-050 1-JJ-70-00111

Pitch lever

Pitchhebel

1-JJ-70-00112

Pitch slider

Pitchschieber

1-JJ-70-00113

Pitch sleeve

Pitchhülse

1-JJ-70-00122

Washer 7x8.5x4

Hülse 7x8.5x4

RCH-70-051 1-JJ-70-00107

Dog bone

Hundeknochen

1-JJ-70-00108

Washer 2x3x4

Hülse 2x3x4

1-JJ-70-00125

Sleeve 2x5x9.5

Hülse 2x5x9.5

1-JJ-70-00126

Washer 2x5x0.5

Beilagscheibe 2x5x0.5

1-JJ-70-00130

Screw M2x17

Schraube M2x17

RCH-70-052 1-JJ-70-00123

Support

Halterung

RCH-70-053 1-JJ-70-00114

Washer 3x4x0.5

Beilagscheibe 3x4x0.5

1-JJ-70-00115

L-

Lever

L-

Hebel

1-JJ-70-00116

Washer 3x4x5

Hülse 3x4x5

RCH-70-054 1-JJ-70-00119

Frame spacer

Distanzstück

RCH-70-055 1-JJ-70-00117

Tail frame 1

Heckrahmen 1

RCH-70-056 1-JJ-70-00120

Tail frame 2

Heckrahmen 2

RCH-70-057 1-JJ-70-00118

Tail rotor hub

Heckhalter

RCH-70-058 1-JJ-70-00136

Tail blade

Heckrotorblatt

1-JJ-70-00154

Tail blade

Heckrotor

RCH-70-059 1-JJ-70-00151

Main Blade

Hauptrotorblatt

RCH-70-060 1-JJ-70-00146

Main Belt

Zahnriemen

RCH-70-061 1-JJ-70-00002

Screw M3x18

Schraube M3x18

RCH-70-062 1-JJ-70-00005

Screw M2.5x12

Schraube M2.5x12

RCH-70-063 1-JJ-70-00006

Screw M4x24

-

6.5 Paßschraube M4x24

-

6.5

RCH-70-064 1-JJ-70-00007

Self Locking Nut M4

Stoppmutter M4

RCH-70-065 1-JJ-70-00008

Screw

M3x12

Schraube M3x12

RCH-70-066 1-JJ-70-00010

Screw M4x26

-7

Paßschraube M4x26

-7#

RCH-70-067 1-JJ-70-00011

Screw M4x10

Schraube M4x10

RCH-70-068 1-JJ-70-00013

Thrust Bearing 6x14x5

Drucklager 6x14x5

RCH-70-069 1-JJ-70-00015

Bearing 8x14x4

Kugellager

8x14x4

RCH-70-070 1-JJ-70-00040

Servo rod guide

Gestängeführung

RCH-70-071 1-JJ-70-00045

Bearing 5x10x4

Kugellager 5x10x4

RCH-70-072 1-JJ-70-00054

Screw M2.5x8

Schraube M2.5x8

RCH-70-073 1-JJ-70-00055

Bearing 12x24x6

Kugellager 12x24x6

RCH-70-074 1-JJ-70-00056

Bearing 10x19x5

Kugellager 10x19x5

RCH-70-075 1-JJ-70-00081

Nylon Nut M2.5

Nylon Mutter M2.5

RCH-70-076 1-JJ-70-00084

Screw M2.5x8

Schraube M2.5x8

RCH-70-077 1-JJ-70-00085

Screw M2.5x20

Schraube M2.5x20

RCH-70-078 1-JJ-70-00086

Screw M3x8

Schraube M3x8

RCH-70-079 1-JJ-70-00090

rotor head 4 blade top

Rotorkopf 4 Blatt oben

1-JJ-70-00133

rotor head 4 blade bottom

Rotorkopf 4 Blatt unten

RCH-70-080 1-JJ-70-00100

Bearing 7x11x3

Kugellager 7x11x3

RCH-70-081 1-JJ-70-00101

Bearing 3x6x2.5

Kugellager 3x6x2.5

RCH-70-082 1-JJ-70-00109

Blade grip

Rotorblatthalter

RCH-70-083 1-JJ-70-00124

Bearing 5x10x4

Kugellager 5x10x4

RCH-70-084 1-JJ-70-00127

Screw M3x8

Schraube M3x8

RCH-70-085 1-JJ-70-00128

Screw M3x20

Schraube M3x20

RCH-70-086 1-JJ-70-00131

Screw M2x10

Schraube M2x10

RCH-70-087 1-JJ-70-00132

Screw M2x5

Schraube M2x5

RCH-70-088 1-JJ-70-00134

rotor head

5 blade top

Rotorkopf

5

Blatt oben

1-JJ-70-00135

rotor head

5 blade

bottom

Rotorkopf

5 Blatt

unten

RCH-70-090 1-JJ-70-00138

Sleeve 2x5x6.5

Hülse 2x5x6.5

1-JJ-70-00139

Ball Link

Kugelkopfverbinder

RCH-70-091 1-JJ-70-00140

Screw M2x14

Schraube M2x14

RCH-70-092

RCH-70-093 1-JJ-70-00142

Uniball 5mm

RCH-70-094 1-JJ-70-00143

Pitch lever 4 blade

Pitchhebel 4 Blatt

RCH-70-095 1-JJ-70-00144

Pitch lever 3 blade

Pitchhebel 3 Blatt

RCH-70-096 1-JJ-70-00145

Tail shaft 3/4 blade

Heckwelle 3/4 Blatt

RCH-70-097 1-60-WJ-00015

Washer 12x18x0.1

Beilagscheibe

12x18x0.1

RCH-70-098 1-JJ-70-00043

Set screw

M4x4

Madenschraube M4x4

RCH-70-099 1-JJ-70-00053

Screw M3x6

Schraube M3.6

RCH-70-100 1-JJ-70-00052

Washer 3x7x0.5

Beilagscheibe 3x7x0.5

RCH-70-101 1-JJ-70-00048

Ball link 5mm

Kugelkopf 5mm

RCH-70-102 1-JJ-70-00059

Screw M3x10

Schraube M3x10

RCH-70-103 1-JJ-70-00069

Nut M2

Mutter M2

RCH-70-104 1-JJ-70-00091

Bearing 12x18x4

Kugellager 12x18x4

RCH-70-105 1-60-WJ-00004

Shaft bevel gear

Kegelrad 20T

RCH-70-106 1-JJ-70-00089

Washer 10x13x0.1

Beilagscheibe

10x13x0.1

RCH-70-107 1-JJ-70-00129

Nylon Nut M2

Nylon Mutter M2

RCH-70-108 1-JJ-70-00141

Tail spindle

Heckrotor Welle

RCH-70-109 1-JX-47-00115

Rotor hub 3 blade

Rotorkopf 3 Blatt

RCH-70-110 1-JX-47-00103

Rotor hub 4 blade

Rotorkopf 4 Blatt

NOTES:

www.robanmodel.com

Roban Bell AH-1W Compactor, AS-350, B212, B412, B 429 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual