Roadmaster 12"" Subwoofer VSW120 Instruction Manual
• Nail Set/Center Punch
• Marker/Pen
• Safety Glasses
• Electrical Tape
• Phillips Screwdriver
• Hammer
• Wire Cutter
• Electric Drill
with 1/16" bit
GIVE US A CALL, WE'LL HELP YOU INSTALL.
1-800-445-1797
PLEASE DO NOT RETURN PRODUCT TO STORE.
Visit us on the WEB
www.vr-3.com
For Information and Technical Assistance,
Call Toll-Free in U.S.A. and Canada.
Subwoofer Terminals
Wires from Amplifier
VSW120
12” Subwoofer
Dear Customer,
CONGRATULATIONS. The VSW120 Subwoofer, when used as described, will give you years
of dependable service in your car, truck, RV or mini-van. We have taken numerous measures
in quality control to ensure that your product arrives in top condition, and will perform to your
satisfaction. In the rare event that your VSW120 Subwoofer contains a damaged or missing
item, does not perform as specifi ed, requires warranty service or you have an installation
problem, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR TOLL
FREE NUMBER FROM THE U.S.A. AND CANADA (800-445-1797) and ask to speak with
a member of our technical service team, or submit your questions by e-mail our web site
vr-3.com, and a member of our technical service team will respond by e-mail to your questions. Our in-house technical service team will expedite delivery of your part, advise you on
installation, or help troubleshoot a problem with you. If your product needs warranty service,
our technical service team representative will help you obtain the fastest remedy possible
under the warranty.
Before You Install
Tools Needed to Install
• 12” Embossed Polypropylene Cone
• 26.5 oz. Magnet Weight ±10%
• Black Rubber Surround
• 400 Watts Maximum Peak Power
• 40 watts RMS per Voice Coil
• 35 to 2000 Hz Frequency Response
• 2” ASV, Dual Voice Coil
• Impedance 4 Ohms +/- 15%
• Sensitivity 89db 1W/1M Minimum
• Quick Connect Terminals (Spade Lug Type)
Automotive audio equipment installations can be troublesome at times, even to the
most experienced of installation technicians. If you are not confi dent working with
electrical wiring, removing and reinstalling interior panels, carpeting, dashboards or
other components of your vehicle, please call our toll free help line (800) 445-1797
and our in-house technical service team will answer your installation questions.
Most car stereos do not have enough power to drive separate subwoofers, if your
mobile auto audio system does not have a separate amplifi er installed, you will most
likely need to install one.
Before permanently installing the VSW120 speakers in your car, connect the wires
to the speakers according to your audio systems installation manual, in the approximate location you will install them. If you are satisfi ed with the location proceed with
the permanent installation.
If you are building your own sealed
box enclosure, it should have a volume of 1.5 to 2.0 cubic feet, and
made with a minimum of 5/8” thick
particle board or M.D.F.. Make
sure that you screw and glue it together for a proper seal, caulk all
seams, and joints with silicone rubber caulking. The inner walls of the
enclosure should be covered with a
sound absorbing material. Maintain
polarity of the amplifi er and speak-
er for proper phase alignment. This
insures the VSW120 operates at
maximum effi ciency.
Seal the hole with silicone
caulking where the wire
passes through the side of
the speaker box.
Cover all inside walls of the en closure
with a sound deadening mater ial such
as Dacron batting.
5/8” thick
particle board
or M.D.F.
Give Us A Call, We’ll Help You Install
Speaker wire of 18 Gauge to 12 Gauge may be used with the VSW120C. You can
purchase speaker wire with spa de lug type female disconnects pre -installed on one end.
Installation
To attach speaker wires (not
included) with female quick
connects (spade lug type) to
the speaker terminals.
Push the female quick
connects (spade lug type) onto
the terminals. Maintain proper
polarity by attaching the Positive Wire (+) to Positive Terminal (+) and the Negative Wire (-)
to Negative Terminal (-).
If the female quick connects
can be easily pulled off, they
can be tightened a little bit by
lightly squeezing them with
a pair of pliers. Do not fl atten
them completely.
Wiring
Installing in a Enclosure
The VSW120 is designed to give you optimum bass per formance when installed in a
sealed speaker enclosure.
Specifi cations
Read First!
Limited Warranty
VIRTUAL REALITY V IDEO LABS® products are desig ned and manufactured to p rovide a high level of trouble -free performance. VIRTUAL RE ALITY VIDEO LABS
®
warrants, to the origi nal purchaser, that its pr oducts are free fro m defects
in material and workma nship for 30 days from the date of origina l purchase, as part of our commit ment to product
excellence. VIRTUAL RE ALITY VIDEO LABS
®
and/or its affi liates routine ly improves the designs, m aterials or produc-
tion methods of its existi ng products. Becau se it is impractical to p ublicize all changes i n every product, we res erve the
right to make such change s without notice.
CONDITIONS OF WARRA NTY:
If during the 30 day warran ty period your new product i s found to be defective, VIRTUAL R EALITY VIDEO LABS
®
will
repair such defect, or r eplace the product, wi thout charge for part s or labor subject to the fol lowing conditions:
1. All repairs must be per formed by VIRTUAL REAL ITY VIDEO LABS
®
and/or its affi liates in Eatontown, New Jersey.
2.
The equipment must not h ave been altered or been d amaged through negli gence, accident, or im proper operation.
3.
The replacement of pa rts are exempted from this wa rranty when replac ement is necessar y due to normal wear and tea r.
4. All warranty claims m ust be accompanied by a co py of the sales receipt or bil l of sale.
5. Repair or replacem ent parts supplie d by VIRTUAL REALIT Y VIDEO LABS
®
under this warranty a re protected only for
the unexpired porti on of the original warrant y.
6. In the case of car stereos , this warranty does not ex tend to the elimination of car s tatic or motor noise; corre ction of
antenna problems; cos ts incurred for the removal o r reinstallation of the prod uct; damage to tapes, spea kers, accessories or car elect rical systems.
7. VIRTUAL REALITY VIDEO L ABS
®
will not be responsibl e for any charge incurre d for installation.
OWNER’S RESPONSIBILITIES:
VIRTUAL REALITY V IDEO LABS
®
will make every effort to provide warranty service within a reasonable period of
time.
SHOULD YOU HAVE ANY QUESTIONS AB OUT SERVICE RECEIVED, OR IF YOU WOULD LIKE ASS ISTANCE IN OBTAINING SERVICE, PLEASE CALL TO LL FREE 1-800-445-1797, 8:30am - 4:30pm EST.
In order to provide you with th e proper warranty ser vice, we request that yo u adhere to the following proc edure:
1. Include a copy of your sales rec eipt or bill of sale with your u nit when it is returned for wa rranty service.
2. If it is ne ces sar y to r etur n you r pr oduc t for ser vic e, pl ease retu rn i t sec ure ly pa cked , pre fer ably in th e ori gin al sh ippi ng
carton, and freight a nd insurance prepaid to th e following address: VIRTUAL R EALITY VIDEO LABS, S ervice Department, 41 James Way, Eatontown, New Jersey 07724.
3. Please include a detai led explanation of the pro blem you are having.
4. If your product is found by VI RTUAL REALITY VIDEO LABS
®
to have a defect in material or workmanship, within
the warranty period , it will be repaired or repla ced at no charge and return ed to you prepaid. Where per mitted by Iaw
VIRTUAL REALITY V IDEO LABS
®
liability shall be lim ited to that set forth in this warra nty. This warranty shall be the
exclusive remedy of the pur chaser.
Notes
Frequently Asked Questions
What if there is no sound?
1. Your stereo may have a blown fuse.
Replace fuse with the same amperage and sty le.
2. You may have improper wiring.
Refer to the wiring guide that came with your stereo/amplifi er. Check all wires for a secure
connection.
What if the sound volume is low?
Your stereo may not have enough power, you may have to install an amplifi er to drive a
subwoofer.
Why do I have a whining noise coming from the subwoofer?
You may have poor fi ltering of your alternator. If that is the case, then you may need to add
an alternator fi lter to the power lead.
Why do I have odd sounding noises coming from the subwoofer?
You may have corroded battery terminals and/or a weak battery. If the terminals on the
battery are corroded, clean them; then c heck the sound. If the sound system is still making
noises check battery strength. If it is low rech arge or replace the battery.
Location Of Subwoofers
Virtual Reality S ound Labs® makes no other warrant y of any kind, expressed o r implied; and all impli ed warranties, are
hereby disclaimed by V irtual Reality Sound La bs
®
and excluded from this war ranty, Virtual Reality So und Labs®, the
manufacturer, distribu tor and seller shall n ot be liable for any injur y, loss or damage, inci dental or consequ ential, arising
out of the use or intended u se of the product
©2008 Intellectua l Solutions, Inc., A ll Rights Reserve d. All designs, log os and images are th e exclusive proper ty of Intellectual S olutions Inc.
and/or its affi lantes. US and Foreign Patents Pending. 071608 Printed in China 00000
Recommendations for Positioning the VSW120 in Your Vehicle:
Cars: Hatch Back or Trunk
SUVs: & Mini Vans: Cargo Area
Pick-up Trucks: Behind Front Seat
All auto audio components must be securely mounted. Driving styles and
road conditions such as sudden stops, sharp curves, and bumpy roads may
cause unsecured items to move about the vehicle, causing physical injuries
to vehicle occupants and/or vehicle damage.
Before installing in an enclosure use the VSW120 as a guide to mark the enclosure
for pilot holes. When you have marked the pilot hole positions drill them with a bit
that is smaller than the screws you will use to secure the speaker to the enclosure.
Attach the positive (+)
and negative (-) wires
found inside the
enclosure box to the
VSW120 terminals. Attach Positive (+) to positive (+), and negative (-)
to negative (-).
Place the subwoofer
into the opening of the
enclosure. Then align
the screw holes of the
subwoofer with the pilot
holes that you drilled.
Tighten the screws.
Place a subwoofer grill
(optional) over the subwoofer, then fasten the
subwoofer grill in place.
Attach wires from audio
source to the terminals
on back of the enclosure.
Loading...