RND lab 355-00009 User Manual

USER MANUAL

Prior to use this product, please read this manual carefully to avoid any damage caused by error operation or improper use.

Distrelec Group AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T [phone], [e-mail], distrelec.com

Introduction

Thank you for purchasing this product. Before use, please read carefully the instructions for

use. This product is a kind of device used as a tool, which is suitable for the detection of

pipelines, narrow spaces, installation of equipment or fixtures, vehicle maintenance, etc.,

providing real-time video viewing and output functions.

Product Features

• Real-time video playback and output;

•

Mini 8mm waterproof LED Lens with 770mm flexible tube (Ben section of

tube is of 4.4mm diameter);

2.0X digital zoom capability;•

• 4.3 inch CD monitor;

• Adjustable brightness on screen and LED light;

• Image flip function (mirroring and 180 degree rotation)

• Accessories: Hook, Magnet, Mirror, Attachment fixture;

• Manufactured and tested to IP67 waterproof standard.

Packing List

Product

User Manual

Single Hook

Magnet

Distrelec Group AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T [phone], [e-mail], distrelec.com

Mirror Attachment Fixture

Structure

Mini waterproof

camera

Screen brightness

adjustment key

Flip/mirroring key

Color LED screen

Installation and Use

Power indicator

ON/OFF key

LED light brightness

adjustment key

Zoom key

VIDEO output interface

1. Open the battery compartment rear cover, install 4 AA batteries and press the

battery cover back (Figure 1); place two fingers simultaneously at the “OPEN”

positions and slightly dig inwards. After a “Click” sound is heard, release a lenght of

tube as required and then snap the rear cover back (Figure 2).

Battery
compartment

real cover

Figure
1

Figure
2

Distrelec Group AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T [phone], [e-mail], distrelec.com

2.

Accessories Installation

(1) First place the single hook or mirror into the hole on the lens as indicated by the

arrow, and then push the attachment fixture to secure it (as shown below).

(2) First, insert the magnet into the attachment fixture, with the pointed end placed

into the hole on the lens as indicated by the arrow, and then tighten the attachment

fixture to secure it (as shown below).

Attachment fixture

Magnet

Press and hold the ON/OFF key for 5s until the power indicator lights up,

3.
while the device enters the real-time video shooting screen; to turn it off, press and hold

the ON/OFF key for 5s again.

Battery level display

ON/OFF key

Distrelec Group AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T [phone], [e-mail], distrelec.com

4.

When the camera’s ambient light is inadequate, the LED light can be turned on

to adjust the brightness. As the brightness is adjusted to the maximum point,

press the brightness adjustment key again to restore.

LED brightness
adjustment key

5.

Press the screen brightness adjustment key to manually adjust the screen

brightness. As the brightness is adjusted to the maximum point, press the

brightness adjustment key again to restore.

Screen brightness
adjustment

Distrelec Group AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T [phone], [e-mail], distrelec.com

6. The zoom key allows you to zoom in the image; press once to zoom in by 1.5
times, press again to zoom in by 2.0 times, and press once again to restore.

Zoom in by

1.5 times

Zoom in by

2.0 times

Zoom key

7. Press the flip/mirroring key to achieve mirroring and 180° flip of the video image.

Flip/mirroring key

Attentions

1. Pay attention to protection of the camera lens, wich shall not be folded by force and
shall not be broken off.

2. The camera Tube is waterproof while the receiver is not. Please protect it from water
and moisture.

3. When the product is not in use, remove the battery.

Distrelec Group AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T [phone], [e-mail], distrelec.com

Technical Parameters

Items

Camera Diameter
Image Sensor
Effective Pixel
Horizontal View Angle
Tube Lenght

IP Grade
Power Supply
Display Dimensions
Image Zoom Ratios

Video Formats

Power Consumption
Product Dimensions
Operating Temperature
Storage Temperature

Operating Humidity
Weight

Above parameters are subject to minor changes without prior notice.

*

Specs

8mm

1/9”, CMOS

640*480 pixels
45±5°

770mm
IP67(excluding the joint part)
AA x 4

4.3” TFT LCD inch
X1.5, X2

NTSC and PAL

1.5W(MAX)

180*36*89mm

-10~+50°C

-20~+60°C

15%~85% RH

325±5g

FCC Certification Info

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

Distrelec Group AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T [phone], [e-mail], distrelec.com

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Distrelec Group AG, Grabenstrasse 6, 8606 Nänikon, Switzerland, T [phone], [e-mail], distrelec.com