8
D
C
Option Accessories
B
Pump-thru & Cal Cap Kit
SKU#: 85930-006-000
A
Q-View & USB-RS485 Converter Kit: 85930-004-000
7
:
*Option Accessories are not included in Q5 Standard Package.
Splash Guard Kit
SKU#: 85930-007-000
6
Duct Mount Adapter
Kit: 85930-040-000
678
5
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
Quatrosense Environmental Ltd. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
Quatrosense Environmental Ltd. IS
PROHIBITED.
5
4
NEXT ASSY USED ON
APPLICATION
4
3
ECN REV. DESCRIPTION DATE DRAW CHECK APPROVED
924 A Initial Release
929 B Update Duct Mount Kit 2010/08/23 XY XY XY
2
REVISIONS
2010/02/25
1
XY XY XY
SPECIFICATION
INPUT POWER:
+24VDC nominal, range: 18 to 30VDC 0.3A DC Total Max.
~24VAC nominal, range: 15 to 24VAC 50/60HZ 0.3A AC Total Max.
(AC must not be grounded)
FUSE:
F2 on Main Board: Polyswitch 750mA
Polyswitch device resets after the fault is cleared and power to the
circuit is removed
SENSOR:
Combustible gases: Catalytic
Toxic gases and Oxygen: Electrochemical
OUTPUT SIGNAL:
RS-485 with OPTIMUX PROTOCOL AND MODBUS PROTOCOL
AVAILABLE CONTROLLER: M-CONTROLLER or Q4 CONTROLLER
4-20mA Analog Output, 1-5VDC, 2-10VDC Output
3X SPDT RELAYS: 1.0A MAX. @30VDC (RESISTIVE LOAD)
0.3A MAX. @125VAC (RESISTIVE LOAD)
ENCLOSURE:
IP 66 & NEMA 4, 4X, 12 & 13
OPERATING TEMPERATURE:
-40°C to 70°C, depends on sensor specification
AMBIENT HUMIDITY:
5% TO 95% RH (NON- CONDENSING)
STORAGE TEMPERATURE:
0°C to 20°C, depends on sensor specification
SIZE:
150mm X 90mm X 65mm
WEIGHT:
LESS THAN 0.5lbs
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL 1/32
ANGULAR:
MACH .5 degrees BEND
TWO PLACE DECIMAL .02
THREE PLACE DECIMAL .010
INTERPRET GEOMETRIC
TOLERANCING PER:
MATERIAL
FINISH
DO NOT SCALE DRAWING
3
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
NAME
XY
XY
XY
2010/02/25
2010/02/25
2010/02/25
DATE
TITLE:
SIZEBDWG. NO.
SCALE: 1:8
2
Quatrosense Environmental Ltd
Q5
INSTALLATION DRAWING
85950-002-000
WEIGHT:
SHEET 1 OF 5
1
REV
B
D
C
B
A
8
7
6
5
4
ZONE REV. DESCRIPTION DATE APPROVED
- - See Sheet1 - -
3
2
REVISIONS
1
Power and RS-485 Connection:
D
Q5 MAIN BOARD
D
C
B
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
A
NOTE:
GROUND THE SHIELD IN CONTROLLER SIDE1.
GROUND ON ONE END ONLY2.
678
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
5
NEXT ASSY USED ON
APPLICATION
4
ANGULAR: MACH BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
INTERPRET GEOMETRIC
TOLERANCING PER:
MATERIAL
FINISH
DO NOT SCALE DRAWING
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
3
XY
XY
XY
2010/02/25
2010/02/25
2010/02/25
DATENAME
Quatrosense Environmental Ltd
TITLE:
Q5
INSTALLATION DRAWING
SIZEBDWG. NO.
85950-002-000
SCALE: 1:2
2
SHEET 2 OF 5
1
C
B
A
REV
B
8
7
6
Power and RS-485 Connection:
D
Q5 MAIN BOARD
5
4
ZONE REV. DESCRIPTION DATE APPROVED
- - See Sheet1 - -
3
2
REVISIONS
1
D
C
B
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
A
NOTE:
GROUND THE SHIELD IN CONTROLLER SIDE1.
GROUND ON ONE END ONLY2.
678
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
5
NEXT ASSY USED ON
APPLICATION
4
ANGULAR: MACH BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
INTERPRET GEOMETRIC
TOLERANCING PER:
MATERIAL
FINISH
DO NOT SCALE DRAWING
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
3
XY
XY
XY
XY
DATENAME
2010/02/25
2010/02/25
2010/02/25
2010/02/25
2
Quatrosense Environmental Ltd
TITLE:
Q5
Installation Drawing
SIZEBDWG. NO.
85950-002-000
SCALE: 1:2
WEIGHT:
SHEET 3 OF 5
1
C
B
A
REV
B
8
7
6
5
4
ZONE REV. DESCRIPTION DATE APPROVED
- - See Sheet1 - -
3
2
REVISIONS
1
D
D
Terminator Enable/Disable?
The terminator on each end of the RS485 loop is designed to
match the electrical impedance characteristic of the twisted pair
loop, and will prevent signal echoes from corrupting the data on
C
the line. The terminator should be enabled on BOTH ends of the
RS485 loop. Short and medium length modbus/485 loops can
operate without the terminating resistor. Longer runs may require
the terminating resistors. But adding terminator dramatically
increases power consumption.
C
Sensor Location:
Several factors should be considered when selecting locations to install
sensors. The following general suggestions should be considered to assure
the detection of the target gas. Select the most suitable location for each
sensor.
1. Air Currents: If there are fans, winds, or others sources of air movement,
gases may tend to rise to collect in certain areas of a facility. The local air
B
currents should be assessed to aid in selecting the sensor location. In outdoor
situations considerations such as prevailing winds should be accounted for.
Air convection can often be more important in determining gas concentrated
areas than factors of Vapor Density.
2. Vapor Density: For the target gas heavier than air. Detecting location
should be 9 - 18 inch (0.23m to 0.46m) above the floor.
3. Gas Emission Sources: As a rule, at least one sensor should be located in
close proximity to each point where a leak is likely to occur. This is particularly
important when a liquid having a low volatility is monitored.
4. Environmental Factors: Designed to rugged outdoor use consider the
following in selecting locations. Install sensors where they will be protected
from wind, dust, snow, water, vibration and shock.
B
Twisted Pair?
A
RS-485 is designed to be a balanced system. The signal on one
wire is ideally the exact opposite of the signal on the second
wire. In other words, if one wire is transmitting a high, the other
wire will be transmitting a low, and vice versa. Although RS-485
can be successfully transmitted using multiple types of media, it
should be used with wiring commonly called "twisted pair."
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
678
5
NEXT ASSY USED ON
APPLICATION
4
INTERPRET GEOMETRIC
TOLERANCING PER:
MATERIAL
FINISH
DO NOT SCALE DRAWING
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
3
NAME
XY
XY
XY
DATE
2010/02/25
2010/02/25
2010/02/25
2
Quatrosense Environmental Ltd
TITLE:
Q5
INSTALLATION DRAWING
SIZEBDWG. NO.
85950-002-000
SCALE: 1:2
SHEET 4 OF 5
1
A
REV
B
8
4-20mA and VDC Output:
D
7
6
5
4
ZONE REV. DESCRIPTION DATE APPROVED
- - See Sheet1 - -
3
2
REVISIONS
1
D
C
B
Q5 provides one channel 4-20 milliamp analog
output and 1-5VDC or 2-10VDC analog output . The
maximum output impedance is 600 ohms for 4-20mA
output. The maximum current is 10 mA for VDC
output.
A
Test point SIG+ and SIG- are used to measure the
current online when the Q5 is working in the field.
678
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
<INSERT COMPANY NAME HERE>. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
<INSERT COMPANY NAME HERE> IS
PROHIBITED.
5
NEXT ASSY USED ON
APPLICATION
4
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
ANGULAR: MACH BEND
TWO PLACE DECIMAL
THREE PLACE DECIMAL
INTERPRET GEOMETRIC
TOLERANCING PER:
MATERIAL
FINISH
DO NOT SCALE DRAWING
3
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
NAME
XY
XY
XY
DATE
2010/02/25
2010/02/25
2010/02/25
2
Quatrosense Environmental Ltd
TITLE:
Q5
INSTALLATION DRAWING
SIZEBDWG. NO.
85950-002-000
SCALE: 1:2
SHEET 5 OF 5
1
C
B
A
REV
B
Loading...