RKC Instrument Inc ST-230L-K-1000-6C/C*K, ST-230L-K-1000-3C/F*K, ST-230L-K-1000-6C/F*K, ST-230-K-1000-3C/C*K, ST-230-K-1000-3C/F*K User manual
...Page 1
Handheld Static Surface Temperature Sensor
ST-230/ST-230L
Thank you for purchasing this RKC product. In order to achieve maximum
performance and ensure proper operation of the instrument, carefully read all
the instructions in this manual. Please place the manual in a convenient
location for easy reference.
This sensor is designed for temperature measurement only.
It should not be used for any other purpose.
An external protection device must be installed if failure of
this instrument.
This instrument is intended for use with industrial machines,
test and measuring equipment. It is not designed for use
with medical equipment.
RKC is not responsible if this instrument is repaired,
modified or disassembled by other than factory-approved
personnel. Malfunction can occur and warranty is void under
these conditions.
NOTICE
RKC is not responsible for any damage or injury that is caused as a result of
using this instrument, instrument failure or indirect damage.
RKC is not responsible for any damage and/or injury resulting from the use
of instruments made by imitating this instrument.
Every effort has been made to ensure accuracy of all information contained
herein. RKC makes no warranty expressed or implied, with respect to the
accuracy of the information. The information in this manual is subject to
change without prior notice.
No portion of this document may be reprinted, modified, copied, transmitted,
digitized, stored, processed or retrieved through any mechanical, electronic,
optical or other means without prior written approval from RKC.
All Rights Reserved, Copyright 2009, RKC INSTRUMENT INC.
RKC INSTRUMENT INC.
®
Safety Precautions
FEB. 2021 IMD01Z01-E2
Handling Precautions
Fig. 2
Fig. 1
Sensing
point
Handle
Head
part
Use the sensor at the usable temperature range.
Usable temperature range:
40 to 300 C [ 40 to 572 F] (Sensing p oint)
[Allowable maximum temperature of a handle: 100 C (212 F) ]
(Maximum continuous usage of tip: 1 minute)
To protect the sensor from fire, explosion or sensor malfunction, do not use the
sensor where it is influenced by flammable, explosive, or corrosive gases; vapor;
or powder dusts.
This sensor is designed to measure the temperature of a static surface. Sliding
the sensor across the measured surface when measuring temperature may cause
distortion or damage to the sensing point.
When measuring temperature, press the sensor against the surface to have
appropriate contact load within 0.9 N to 6.0 N (the minimum distance between the
handle and the head part should be 5 mm or less). (Refer to fig. 2.)
Pressing the sensor forcibly may cause distortion or damage t o the sensing point
and cause measurement error.
If the sensor is kept in contact with an object over a long period of time, used on a
curved surface such as a roller, or pressed with a load exceeding the normal load
range, a mark may be left on the measurement surface.
Place the sensor against the object
and press it keeping a distance of
5 mm or less between the sensor head
and the handle. This could be
approximately a contact load of 0.9 N
to 6.0 N. Avoid contact between the
head and the handle.
To obtain an accurate reading, the surface should not be curved, rough or
unclean. The reading may become lower if the contact is not secured enough.
Pushing or hitting the metal sensing point may cause deformation.
Cover the head with a cap to protect the metal sensing point.
Do not touch the sensing point after measuring until it returns to the ordinary
temperature. Take caution to avoid being burned or frostbitten.
When measuring a high temperature object, carefully use the sensor as the
handle may be heated high and your hand may be burned.
Do not use the sensor in electricity environment because of electric shock.
Keep the sensor in a dry indoor place.
The first edition: NOV. 2009 [IMQ00]
The second edition: FEB. 2021 [IMQ00]
Head
part
Handheld Static Surface Temperature Sensor
ST-230/ST-230L
Thank you for purchasing this RKC product. In order to achieve maximum
performance and ensure proper operation of the instrument, carefully read all
the instructions in this manual. Please place the manual in a convenient
location for easy reference.
This sensor is designed for temperature measurement only.
It should not be used for any other purpose.
An external protection device must be installed if failure of
this instrument.
This instrument is intended for use with industrial machines,
test and measuring equipment. It is not designed for use
with medical equipment.
RKC is not responsible if this instrument is repaired,
modified or disassembled by other than factory-approved
personnel. Malfunction can occur and warranty is void under
these conditions.
NOTICE
RKC is not responsible for any damage or injury that is caused as a result of
using this instrument, instrument failure or indirect damage.
RKC is not responsible for any damage and/or injury resulting from the use
of instruments made by imitating this instrument.
Every effort has been made to ensure accuracy of all information contained
herein. RKC makes no warranty expressed or implied, with respect to the
accuracy of the information. The information in this manual is subject to
change without prior notice.
No portion of this document may be reprinted, modified, copied, transmitted,
digitized, stored, processed or retrieved through any mechanical, electronic,
optical or other means without prior written approval from RKC.
All Rights Reserved, Copyright 2009, RKC INSTRUMENT INC.
Find Quality Products Online at: sales@GlobalTestSupply.com
www.GlobalTestSupply.com
RKC INSTRUMENT INC.
®
Safety Precautions
FEB. 2021 IMD01Z01-E2
Handling Precautions
Fig. 2
Fig. 1
Sensing
point
Handle
Head
part
Use the sensor at the usable temperature range.
Usable temperature range:
40 to 300 C [ 40 t o 572 F] (Sensing point)
[Allowable maximum temperature of a handle: 100 C (212 F) ]
(Maximum continuous usage of tip: 1 minute)
To protect the sensor from fire, explosion or sensor malfunction, do not use the
sensor where it is influenced by flammable, explosive, or corrosive gases; vapor;
or powder dusts.
This sensor is designed to measure the temperature of a static surface. Sliding
the sensor across the measured surface when measuring temperature may cause
distortion or damage to the sensing point.
When measuring temperature, press the sensor against the surface to have
appropriate contact load within 0.9 N to 6.0 N (the minimum distance between the
handle and the head part should be 5 mm or less). (Refer to fig. 2.)
Pressing the sensor forcibly may cause distortion or damage t o the sensing point
and cause measurement error.
If the sensor is kept in contact with an object over a long period of time, used on a
curved surface such as a roller, or pressed with a load exceeding the normal load
range, a mark may be left on the measurement surface.
Place the sensor against the object
and press it keeping a distance of
5 mm or less between the sensor head
and the handle. This could be
approximately a contact load of 0.9 N
to 6.0 N. Avoid contact between the
head and the handle.
To obtain an accurate reading, the surface should not be curved, rough or
unclean. The reading may become lower if the contact is not secured enough.
Pushing or hitting the metal sensing point may cause deformation.
Cover the head with a cap to protect the metal sensing point.
Do not touch the sensing point after measuring until it returns to the ordinary
temperature. Take caution to avoid being burned or frostbitten.
When measuring a high temperature object, carefully use the sensor as the
handle may be heated high and your hand may be burned.
Do not use the sensor in electricity environment because of electric shock.
Keep the sensor in a dry indoor place.
The first edition: NOV. 2009 [IMQ00]
The second edition: FEB. 2021 [IMQ00]
Head
part
Loading...