P
Installation Instructions
MCM -Series TV Mount www.RiteMounts.com
DISCLAIMER
This document is intended to be made accurate and complete. However, there is no
guarantee the information contained here in covers every aspect. The manufacturer
and the distributor make no representation of any warranty regarding the information
contained, and assume no corresponding responsibility.
WARNING:
• Prior to installation, please read and understand this instruction manual. If you have
any questions or uncertainties, please consult your seller or local professionals.
• If the ceiling structure could not support the weight of mount and the TV, please
reinforce the ceiling prior to the installation. Installation on drywall may be
dangerous.
• To avoid damage, a plasma TV should never be laid flat. It must remain in an
upright position.
• Tighten the screws firmly, but never overtighten.
Parts list:
A1 A2
A3-A5 A6
Figure 1: Part list
Features:
Designed for 30” to 60” flat screen TVs
• TV is 26" ~ 32.5" from the ceiling.
We offer a variety of extension pipes to extend the length from the ceiling.
• Up to 50º Tilt side to side, tilt -5º ~ 15º up and down, roll -6º~ +6º to adjust
horizontal level
• Maximum TV Weight: 175 lb / 79.38 kg
Required tools: Stud finder; Screwdriver; Level; Drill
age 1 of 4
Figure 2: Every PARTS and it's position (Part A3~ A5 come assembled)
P
Screw list:
Description Qty
[01] Wood Screw 8
[02] M8 x 40 Screw 4
[03] M8 x 16 Screw 4
[04] M6 x 35 Screw 4
[05] M6 x 12 Screw 4
[06] M5 x 30 Screw 4
[07] M5 x 12 Screw 4
[08] M4 x 30 Screw 4
[09] M4 x 12 Screw 4
[11] W asher for M8 screws 4
[12] Washer for Wood Screws(Qty:8)
and for M6 Screw(Qty:4)
[13] Washer for M5, M4 Screw 4
[14] Spacer for M6 Screw 4
[15] Spacer for M5, M4 Screw 4
[01] (Wood Screw) is used with 4 or 8 [12] (washer) to secure the Part A1 to the wood stud.
[02]~[09] are various screws for all kinds of TVs. They are used with washers [11] ~ [13].
Spacers, [14]~[15] are used to create more space between the TV and the mount when
necessary, for example, curved back of TV, need more room for cable access, and TV with
recessed screws.
Step 1: Mounting TV interface arm (Part-B) to the back of the TV
a) If your TV has a flat back surface – No curves and steps
12
age 2 of 4
Figure 3: install Part-B1 to the TV
b) if your TV has an uneven or curved back surface, use the su pplied spacers
([14]-[15]) to compensate or adjust the height.
If more space are needed between the mount and TV, use spacers [14] or [15] !
Figure 4: install Part-B1 to the TV, II
Step 2: Install the ceiling plate
Woo d s t u d : To install to a typical wood stud ceiling, first identify the wood stud using a stud
finder, then secure the cei ling plate (Part-A1) to the ceiling using wood screws (Part-[01]).
P
Warning: The supplied wood screws (Part-[01]) may be used w ith a drill, but it must be
hand tightened using wrench to avoid damaged on the threads.
Concrete ceiling: Drill holes for the concrete anchor*, insert the anchors, then have the wood
screws screwed into the anchors.
*concrete anchor is sold separately, or available in local hardware stores.
False/Drop/Suspended ceiling: Using our
suspended ceiling adaptor, the mount could be installed
underneath drop ceiling tile. Th e suspended ceiling
adaptor will be supported by the true ceiling structure.
See Figure-6 for the measurement of Part-A1, before you drill holes on the ceiling.
Figure 6
Insert the cables through the central hole on the Ceiling Plate (Part-A1) before
you tighten the screws (Part-[01]).
Mounting to solid ceiling
Use a solid ceiling anchor (not included, can be purchased from local hardware store) along
with the wood screws (Part-[01]). First drill a hole for the solid ceiling anchor, put it in, attach
Part-A1, and screw Part-[01](wood screw) into the solid ceiling anchor.
*solid ceiling anchor is sold separately, or available in local hardware stores.
Warning: Make sure the ceiling can support the combined weight of the mount and the TV.
Step3: Assemble the MCM TV mount
a)Attach Part-A2 and Part-A3
Figure 5
The threaded rods and U-Bolt shown on below on Figure-6 are only used with
following applications. Not applicable to normal residential woo d structures
Threaded Rod / Trusses / I-Beams / Unistrut: See Figure-6, use inner four holes to install
with four 1/4” or 5/16” threaded rods.
age 3 of 4
Figure 7
Get Part-A3 through Part-A2 from the threaded side first.loose out the M4 screw(Part-[10])
which has been locked in Part-A1.Install Part-A3 to Part-A1 and tighten the
connection.Tighten Part-[10] to lock the position between Part-A1 and Part-A3.
Then Part-A2 could be snapped to the ceiling plate (Part-A1), and now turn Part-A2 clockwise,
P
it will be locked on the ceiling.
Note A set screw Part-[10] is used lock Part-A1 and Part-A3, however, do NOT
tighten it until YAW adjustment is completed.
b)Attach Part-A6
Figure 8
c)Adjust the high from the ceiling.
6.5" adjusted are designed to make MCM can meet your TV size or to make a little high
adjustment.Loose the 2 bolts which has been tightened in Part-A4(Figure 9).Move to the
position you need and tighten the bolts again.
We offer a variety of extension pipes to extend the length of Part-A3.
Step 4: Hang the TV with the interface arms installed (Part-B) onto
the ceiling pipe arms (Part-A6)
Hook the TV with arms (Part-B) installed onto the top of the ceiling pipe arms (Part-A6), then
slowly swing screen inward.
Figure 9: Hook on TV with Part-B1
The cables which had bee n inserted through the Ceiling Plate (Part-A1) can
exit from the central hole of Part-A3 .
Figure 10: Lock Part-B to Part A
Tilt adjustments
age 4 of 4
P
It can be easily installed to MCM.
Remove MCM pipe arms beacause you don't need them.Install the SLF wall-plate to Part-A5
of MCM with 4 SLF screws,and Install LCD to SLF LCD-plate with another 4 [02]-[13]
screws.Put the LCD up,slide down the LCD-plate into the wall plate of SLF.
Figure 11: Tilt adjustments
Roll adjustments
Roll adjustments are used to make the TV horizontal. Loose the roll adjustment screws at the
back of Part-A4 and tighten after adjustment.
Figure 12: Roll adjustments
Delicate LCD?We offer SLF Plates on below on Figure-6 .
Figure 12: Install SLF to MCM
Figure 13
age 5 of 4
P
Troubleshooting:
1. Some TVs might have cable access in the middle, which might be blocked by
Part-A5. If this is the case, please use Spacers [14] or [15], to increase the distance
between the mount and the TV.
2. If the articulating arms are too tight, some lubricating oil like WD-40 could be safely
applied.
age 6 of 4
Loading...