Rishabh 410 User Manual

Digital Multimeters
RISHABH 410
User Manual
RISHABH 410 Multimeter
1
3
4
5
6
7
8
2
1
(2)
(4)
(3)
(5)
(7)
(8)
(9)
(6)
(1)
Multimeter Operating Elements
Data HOLD Pushbutton
Backlight Pushbutton (optional).
8
9 Terminal Sockets
LCD Display
2
Hz/% Pushbutton for VAC & VDC.
1. Safety Features and Precautions ...................
2. Initial Start-up ...................................................
3. Selecting Measuring Functions & Ranges ....
3.1 Measuring Function Selection............................
3.2 Automatic Measuring Range Selection..............
3.3 Manual Measuring Range Selection..................
4. Liquid Crystal Display ....................................
4.1 Digital Display ...................................................
4.2 Display with Backlit(optional).............................
5.0 Buzzer ..............................................................
6.0 Measurement Value Storage ” HOLD”............
7.0 REL - Relative value measurement ...............
8.0 Voltage Measurement .....................................
9.0 Current Measurement ....................................
9.1 AC Measurement with (Clip-on) C.T. ................
10.0 Diode Testing & Continuity Measurement ....
10.1 Diode Testing ....................................................
10.2 Continuity Testing .............................................
11.0 Resistance Measurement ...............................
12.0 Capacitance Measurement ............................
13.0 Frequency & Duty cycle Measurement ........
13.1 Frequency Measurement .................................
13.2 Duty Cycle Measurement .................................
14.0 Temperature Measurement ............................
15.0 Specifications .................................................
16.0 Maintenance ....................................................
16.1 Battery ..............................................................
16.2 Fuses ................................................................
16.3 Housing .............................................................
17.0 Repair and Replacement parts service .........
4 6 7
7 8 8
9
9
9
10 10 10 10 12
13
14
14 15
16 17 19
19 19 20
21 26
26 27 28
28
3
1000 V
4
600 V
15
Meaning of the symbols
CAT II / III
Warning of a danger point (Attention, refer to the user manual)
Earth (ground) terminal.
Double or reinforced insulation
Instrument for over voltage category II / III or IV
EU conformity mark.
5
6
white or yellow print
white half circle is reactivated .
color
7
AC
8
Note :0For Temperature ( C), Frequency (Hz), Duty cycle (%)
and Capacitance (F) measuring range is always Auto. No manual range selection is possible.
The digital display is
updated thrice per
sec-
4.2 Display with Backlight (Optional)
By pressing
User can take reading in poor light condition.
key back light can be made ON or OFF.
9
ond for V, A, W, Cap Freq and duty cycle measurements.
AUTO/MAN key is activated
When measuring AC Voltage > 750 V, DC Voltage > 1000 V, AC/DC mA > 400.0 mA, AC/DC A > 10 A, the buzzer will keep sounding as the overload warning.
Approximate 1 minute before the meter is auto power off, the buzzer will raise constantly 5 sounds to warning. Before the meter is power off, the buzzer will raise one long sound to warn the user.
,Hz\% , Backlight .
10
DC
400 mA
11
After selection of this function with the selector switch, the Current type DC is always activated.
6
12
6
400 mA
13
10 Diode Testing & Continuity Measurement
10.1 Diode Testing
400 mA
14
10.2 Continuity Testing
‘OL’
400 mA
15
11 Resistance Measurement
400 mA
400 mA
16
Deleting Zero Adjustment
Short the leads connected to meter and then press REL key.
or
Activate the function selector switch.
or
Switch the Multimeter off.
400 mA
17
18
13 Frequency & Duty Cycle Measurement
13.1 Frequency Measurement
Set the function selector switch to VAC and press Hz/% key, as shown on page 20. The frequency measurement mode is activated. “Hz” symbol is displayed on the LCD. The digital display is expanded to 9999 digits. Only the auto mode is possible, no manual range is possible.
13.2 Duty Cycle Measurement
With duty cycle measurement, we can determine the ratio of pulse duration to cycle time of recurring square wave signals. The duty cycle that is the percentage pulse duration of signal is displayed on LCD i.e.
Duty cycle (%) =
pulse duration
cycle duration
X 100
Note : The applied frequency must remain constant during the duty cycle measurement.
Set the function selector switch to VAC and press Hz/% key twice as shown on page 20. The Duty cycle (%) mode is activated. “%” symbol is displayed on LCD.
15.
NOTE : Hz/% key is only applicable for VAC.
19
14 Temperature Measurement
Multimeter allows you to measure temperature with K-type
0 0
thermocouple (NiCr-Ni) in the range 0 C to +1300 C.
0
Set the function selector switch to “ C ”. Connect the sensor as shown below.
Connections are made the same way as for Voltage measurement
measuring range for duty cycle and maximum allowable voltage can be found in chapter “Specifications”.
V~
K-type sensor
Press Hz/% key
Press Hz/% key
Press Hz/% key
Press Hz/% key
400 mA
400 mA
20
15 Specifications
Meas.
Function
Measuring
Range
Resolution
Input Impedance
400.0mV
4.000V
40.00V
400.0V 1000V
400.0mV
4.000V
40.00V
400.0V 1000V
100mV
1mV
10mV
100mV
1V
100mV
1mV
10mV
100mV
1V
40.00mA
400.0mA
1)
10.00A
40.00mA
400.0mA
1)
10.00A
10mA
100mA
10mA 10mA
100mA
10mA
400.0W
4.000kW
40.00kW
400.0kW
4.000MW
40.00MW
400.0W
1.000V
5.000nF
50.00nF
500.0nF
5.000mF
50.00mF
200.0mF
100mW
1W
10W
100W
1kW
10kW
100mW
1mV
1pF
10pF
100pF
1nF
10nF
100nF
10.000Hz
100.00Hz
1.0000kHz
10.000kHz
100.00kHz
500.0kHz
0.001Hz
0.01Hz
0.1Hz 1Hz
10Hz
100Hz
2.0...98.0% 0.1%
V(AC) / V(DC)
>20MW
11MW 10MW 10MW 10MW 11MW 11MW 10MW 10MW 10MW
Approx. Voltage drop
at max. meas. current
450mV
4.2V 750mV 450mV
4.2V 750mV
Open-circuit voltage
approx 0.45V
approx 1V
10Hz
10Hz
10Hz
10Hz
10Hz
10Hz
f
min
F
Hz
%
V
V
A
A
2)
Sensor
0
0...+1300 C
0
C
0
1 C
NiCr-Ni
K-type
1) max. 12 A / 5 min. 16 A / 30 Sec
2) Indication for frequency measurement expanded to 9999 D
21
40.00mA
400.0mA
4)
10.00A
40.00mA
400.0mA
4)
10.00A
400.0W
4.000kW
40.00kW
400.0kW
4.000MW
40.00MW
400.0W
1.000V
5.000nF
50.00nF
500.0nF
5.000mF
50.00mF
200.0mF
10.000Hz
100.00Hz
1.0000kHz
10.000kHz
100.00kHz
500.0kHz
2.0...98.0%
0
0...+1300 C
0.8+2
1.5+5 1+5
2+5
0.8+5
0.8+2
1+5 2+5
Acoustic signal for
0...<75W (approx)
2+10
2)
3+40
2)
2+10
2)
0.5+3
2)
1+2
2)
1.5+2
3)
5+10
0.2+2
10Hz...1kHz : +5D
1kHz...10kHz : +5D/kHz
2+3
Continuous
Continuous
480mA
4)
480mA
4) 4)
4)
500V
DC/AC
rms
10 min
500V
DC/AC
rms
Continuous
10 min
10 min
<1kHz : 1000V
<10kHz : 400V
<500kHz : 40V
except 400mV
500V DC/AC
rms
Measuring
Range
400.0mV
4.000V
40.00V
400.0V 1000V
400.0mV
4.000V
40.00V
400.0V 1000V
Digital display inherent
deviation at
reference conditions
+ (...% of rdg + ...digits)
0.75+2
0.5+2
1.5+5
1+5
1+10
1)
Overload capacity
Overload value
Overload
duration
1050V(DC)
1050V(AC)
rms
Continuous
Continuous
Meas.
Function
F
5)
Hz
%
0
C
V
V
A
A
0 0
1) At 0 C... + 40 C
2) With zero adjustmet “REL”.
3) Time required for measurement approximately 60 seconds.
4) max. 12 A/5 min 16 A/30 s
5) Indication of the frequency measurement expanded to up to 9999 digits
22
5
58
23
31.4
24
Intrinsic
25
6
6
Simply unscrew the battery compartment cover from base housing. No need to remove whole base housing.
26
6
Be absolutely certain that only the specified fuses as above are used. The use of fuse with different specifications may place the operator, the system & measuring instrument in danger. The use of repaired fuses or short-circuting of the fuse holder is prohibited.
Screw the battery compartment cover to base housing.
Screw the base housing cover to front housing.
Unscrew the base housing cover from front housing.
27
6
28
7
www.rishabh.co.in
Printed in India, Subject to change without Notice
Factory: F-31, MIDC, Satpur, Nashik-422 007 India Phone(0253) 2202202, 2202162
Fax : 91 - 0253 - 2351064, 2202302 E-mail : International: exp.marketing@rishabh.co.in
RISHABH INSTRUMENTS PVT. LTD.
Item Code 15001309Rev A: 23/7/2013
India: marketing@rishabh.co.in
Loading...