Risco RW132KF2 Users Manual

E N G L I S H

F R A N Ç A I S

09/08 RISCO Group
5IN1113

Introduction

The Agility 2-Way remote control is an 8 button rolling code wireless transmitter designed
for remote system operation. The remote control is typically used to set (arm), unset (disarm),
activate devices and get system status. Being bi-directional enables each command that is
sent to the panel to receive a reply status from the panel and indicate the status to the user
via the colour LEDs. For higher security, commands can be defined to be activated with a
4 digit PIN code.
Check with your installer regarding the definitions of the remote control.

* If the 1st LED changes to orange it indicates a low battery condition.

For full installation instructions refer to our website www.riscogroup.com

Common Operations:

CAUTION: risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteriess according to local regulations.

UK Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

ITALY Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

SPAIN Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

FRANCE Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

BELGIUM Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

U.S.A Toll free: 1-800-344-2025
Tel: [phone]
Fax: +305-592+3825
E-mail: [e-mail]

BRAZIL Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

CHINA Tel: [phone]
Fax:[phone]
E-mail: [e-mail]

POLAND Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

ISRAEL Tel: [phone]
Fax: [phone]
E-mail: [e-mail]

RISCO Group Limited Warranty

RISCO Group and its subsidiaries and affiliates ("Seller") warrants its
products to be free from defects in materials and workmanship
under normal use for 24 months from the date of production.
Because Seller does not install or connect the product and because
the product may be used in conjunction with products not
manufactured by the Seller, Seller cannot guarantee the
performance of the security system which uses this product. Seller's
obligation and liability under this warranty is expressly limited to
repairing and replacing, at Seller's option, within a reasonable time
after the date of delivery, any product not meeting the specifications.
Seller makes no other warranty, expressed or implied, and makes no
warranty of merchantability or of fitness for any particular purpose.
In no case shall seller be liable for any consequential or incidental
damages for breach of this or any other warranty, expressed or
implied, or upon any other basis of liability whatsoever.
Seller's obligation under this warranty shall not include any
transportation charges or costs of installation or any liability for direct,
indirect, or consequential damages or delay.
Seller does not represent that its product may not be compromised
or circumvented; that the product will prevent any personal injury or
property loss by burglary, robbery, fire or otherwise; or that the
product will in all cases provide adequate warning or protection.
Buyer understands that a properly installed and maintained alarm
may only reduce the risk of burglary, robbery or fire without warning,
but is not insurance or a guaranty that such event will not occur or
that there will be no personal injury or property loss as a result
thereof. Consequently seller shall have no liability for any personal
injury, property damage or loss based on a claim that the product
fails to give warning. However, if seller is held liable, whether directly
or indirectly, for any loss or damage arising under this limited
warranty or otherwise, regardless of cause or origin, seller's
maximum liability shall not exceed the purchase price of the product,
which shall be complete and exclusive remedy against seller.
No employee or representative of Seller is authorized to change this
warranty in any way or grant any other warranty.

WARNING: This product should be tested at least once a week.

E S P A Ñ O L

Operation Quick High Security Mode

Set (Full) (Away Arm) > Code

Set (Partial) (Stay Arm) > Code

Unset (Full Disarm) > Code

System Status

for 2 seconds for 2 seconds > Code

Output control A/B/C

/ / / /

for 2 seconds for 2 seconds > Code

Panic Alarm + simultaneously for 2 seconds

Lock/Unlock Keys >

Clear Operation >

Introduction

La télécommande bidirectionnelle de l’Agility est un transmetteur 8 boutons à codes tournants
conçue pour commander le système à distance. Elle est utilisée pour armer, désarmer, activer
des périphériques et obtenir l’état du système. Le fait d’être bidirectionnelle lui permet, pour
chaque exécution de commande envoyée à la centrale, de recevoir un retour sur le statut de
la centrale, et de l’afficher via la couleur des LEDs. Pour une plus grande sécurité, les
commandes peuvent être définies pour n’être activées qu’avec un code PIN à 4 chiffres.
Demandez à votre installateur les options de votre télécommande.

Status LED Indications:

Operation 1st LED* 2nd LED*
(Send command) (Receive Status)

Full Setting (Away) Green Red

Part Set (Stay Arm) Green Orange

Unset (Disarm) Green Green

Alarm Green Flash LED

Introducción

El mando bidireccional de la Agility es un transmisor vía radio de 8 botones de código
variable (“rolling code”) diseñado para manejar el sistema remotamente. El mando
normalmente se usa para armar, desarmar, activar dispositivos y conocer el estado
del sistema. Al ser bidireccional, permite que cada comando que se envía al panel
reciba una respuesta del estado desde el mismo, indicando al usuario dicho estado
por medio de un código de colores del LED. Para mayor seguridad, los comandos se
pueden definir para tener que activarse con un código PIN de 4 dígitos.
Consulte con su instalador las definiciones del mando.

FCC NOTE:

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.
FCC ID: JE4RW132KF2 Valid for P/N RW132KF2000H
IC: 6564A-RW132KF2 Valid for P/N RW132KF2000H

This device complies with FCC rules part 15. Operation is subject to the following two
condition:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.

FCC Warning:

The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate
the equipment.

Status BUZZER Indications:

Sound Status

1 beep Confirmation

3 beep Error

5 beep Alarm

Agility Wireless

2-Way Remote Control

4\?

4\?

* Si la 1ère LED est orange, cela indique une condition de batterie basse pour la
télécommande.

Pour les instructions complètes d’installation, reportez vous à notre site web
www.riscogroup.com

Fonctions basiques:

Fonction Rapide Séquence avec code

Armement total > Code

Armement partiel > Code

Désarmement (total) > Code

Etat du système Appui long Appui long > Code

Contrôle de sortie A/B/C

/ / / /

Appui long Appui long > Code

Alarme panique + simultanément pendant 2 secondes

Verrouillage/Déverrouillage
des touches

>

Annuler commande >

LED:

Fonction 1

ère

LED* 2

ème

LED*

(Envoie de commande) (Réception de l’état)

Armée totalement Verte Rouge

Armée partiellement Verte Orange

Désarmée Verte Verte

Alarme Verte LED rouges clignotante

BUZZER:

Son Etat

1 bip Confirmation

3 bips Echec commande

5 bips Alarme

4\?

4\?

Operaciones habituales:

Función Rápido Secuencia con código

Armado Total > Código

Armado Parcial > Código

Desarmado Total > Código

EN50131-1, EN50131-3, Grade 2

EN50130-5, Environmental class II

EN50131-6, Type C

I T A L I A N O

DUTCH

* Si el LED 1º cambia a naranja, indica batería baja del mando.

Función LED 1º * LED 2º *
(Transmisión Comando) (Recepción Estado)

Armado Total realizado Verde Rojo

Armado Parcial realizado Verde Naranja

Desarmado realizado Verde Verde

Alarma Verde LED Rojo parpadea

Introduzione

Il telecomando Agility 2 canali bidirezionale è un trasmettitore radio "rolling code" a 8 tasti
progettato per essere utilizzato con sistemi via radio Agility. Il telecomando viene utilizzato
comunemente per gli inserimenti, il disinserimento del sistema, l’attivazione di dispositivi
esterni e per conoscere lo stato dell’impianto. Il doppio canale bidirezionale permette ad
ogni comando inviato alla centrale d’allarme Agility di ottenere un segnale di stato di
risposta, indicato dal colore dei LED di segnalazione. Per maggior sicurezza è possibile
definire i comandi da attivare con un codice PIN a 4 cifre.
Rivolgersi al proprio installatore per le specifiche del telecomando.

Inleiding

De 2-zijdige Agility-afstandsbediening heeft een draadloze rollende codezender met 8 knoppen
die voor externe systeembediening is ontworpen. De afstandsbediening wordt meestal gebruikt
voor instellen (inschakelen), uitstellen (uitschakelen), apparaten activeren en systeemstatus
krijgen. Omdat het tweerichting is, kan elke opdracht die naar het paneel wordt verzonden
een responsstatus van het paneel ontvangen en deze via de kleuren-LED's naar de gebruiker
doorgeven. Voor grotere veiligheid, kunnen de opdrachten worden gedefinieerd om met een
4-cijferige PIN-code te worden geactiveerd.
Controleer met de installateur betreffende de definities van de afstandsbediening.

Para una información detallada de las instrucciones de instalación, consulte nuestra
web: www.riscogroup.com

ZUMBADOR:

Pitido Estado

1 pitido Confirmación / OK

3 pitidos Fallo del comando

5 pitidos Alarma

LED:

4\?

4\?

4\?

4\?

Algemene handelingen:

Handeling Snel Codesequentie

Instellen (volledig) > Code
(Altijd ingeschakeld)

Instellen (Gedeeltelijk)
(Ingeschakeld blijven) > Code

Niet ingesteld (Volledig
uitgeschakeld) > Code

Systeemstatus Lang Lange > Code

Uitvoerbesturing A/B/C / / / /

Lang Lange > Code

Paniekalarm + Gelijktijdig gedurende 2 seconden

4\?

4\?

Operazioni comuni:

Funzione Scelta rapida Sequenza codice

Inserimento totale > Codice

Inserimento parziale > Codice

Disinserimento totale > Codice

Stato del sistema pressione prolungata

pressione prolungata

> Codice

Controllo uscita A/B/C / / / /

pressione prolungata pressione prolungata > Codice

4\?

4\?

* Se il 1° LED s’illumina d’arancione, indica una condizione di batteria scarica.

Per ottenere istruzioni d’installazione più dettagliate, fare riferimento al nostro sito web
www.riscogroup.it

Operazioni comuni:

Funzione Scelta rapida Sequenza codice

Segnalazione di panico + contemporaneamente per 2 secondi

Blocca/Sblocca tasti

>

Cancella operazione >

LED:

Funzione 1° LED* 2° LED*
(Invio comando) (Riceve Stato)

Inserimento totale eseguito Verde Rosso

Inserimento parziale eseguito Verde Arancione

Disinserimento eseguito Verde Verde

Allarme Verde LED rosso lampeggiate

Segnale Acustico:

Segnale Segnale acustico

1 segnale Conferma

3 segnale Errore

5 segnale Allarme

* Als de eerst LED oranjekleur wordt betekend een lag batterij toestand.

Voor volledige installatie-instructies verwijzen naar onze website www.riscogroup.com

Replacing Batteries:

1. 2. 3. 4.

Algemene handelingen:

Handeling Snel Codesequentie

Toetsen vergrendelen/
ontgrendelen

>

Handeling wissen >

LEDindicaties:

Handeling 1st LED* 2nd LED*
(zend commando) (ontvang statuut)

Succesvol ingesteld
(volledig ingeschakeld) Groene Rode

Succesvol gedeeltelijk
ingesteld (Ingeschakeld
blijven)

Groene Oranje

Succesvol uitgesteld
(uitgeschakeld)

Groene Groene

Alarm Groene Knipperende rode LED

ZOEMERINDICATIES:

Geluid Statuut

1 lang piepgeluid Bevestiging

3 korte piepgeluiden Opdracht mislukt

5 korte piepgeluiden Alarm

Operaciones habituales:

Función Rápido Secuencia con código

Estado del Sistema Mantener pulsado Mantener pulsado > Código

Control de Salidas A/B/C

Mantener pulsado Mantener pulsado > Código

/ / / /

Alarma de Pánico + simultáneamente durante 2 segundos

Bloqueo/Desbloqueo
de Teclas

>

Cancelar la acción

>

4\?

4\?

78mm

37mm

22mm

35g (0.07lb)

78 x 37 x 22 mm
(3.07 x 1.45 x 0.86 inch)

CR-1/3N 3V Lithium battery

3 Years

-20°C to 70°C (-4°F to 158°F)

-10°C to 40°C (14°F to 104°F)

µA

2µA, 20mA (transmission)

1 2 3

June 2008

5 6 7