RIOTEC RIOSCAN iLS6307LS, RIOSCAN iLS6308KS Quick Manual

*

RIOSCAN 2D barcode scanner

Quick Guide

M o del no.:

i L S6307LS

Introduction

Designed primarily for smartphone, the iLS6307LS is a 2D
barcode scanner that allows you to scan various barcoded
items and send data to smartphone.
Its in-built excellent 2D engine allows you to reliably read 2D
barcodes on various shapes and is a great space-saver for
busy or limited workspaces.
It supports not only iOS devices through Bluetooth
communication, but also Android OTG devices through USB
cable

Delivery content

* Bluetooth Barcode scanner x 1
* Charging cradle x 1

* PCB material board+3 screws x 1
* Holder for smartphone x 1
* USB cable x 1
* Quick instructions x 1

Limited Warranty

Riotec provides a one year limited warranty.
This warranty does not cover any product which has been subject
to improper use, neglect or unauthorized repair or installation.
This warranty does not cover consumable parts. (Cables &
batteries are consumables.)

Safety instructions

Read the operating instructions carefully and especially
observe the safety information. If you do not follow the safety
instructions and information on proper handling in this
manual, we assume no liability for any resulting personal
injury or damage to property.

* Don’t put scanner in places excessively high temperatures,

such as expose under direct sunlight

* Don’t use scanner in extremely humid area or drastic

temperature change

* The rechargeable battery is permanently built into the

product and cannot be replaced.

* Never damage the rechargeable battery. Damaging the

casing of the rechargeable battery might cause an explosion
or a fire!

Charging:

1. Please switch on and charge scanner for 3~4 hours before first

use as shown on Fig.2

2. When user charge smartphone & scanner, please use

smartphone original USB power adapter.

3. The cradle functions as a charger for the scanner. Even if the

scanner’s battery is full, the cradle will continue to supply power

to the scanner. We suggest removing the scanner from the cradle
when fully charged.

4. When you charge scanner & smartphone, please enter Wired

OTG mode & switch to “C- Charging mode”.

iLS6307LS supports BT communication mode (for iOS & Android
devices) and wired OTG communication mode (for Android OTG
devices)
If you want to switch to another mode, please read the below configuration
code first.

Bluetooth BT communication

wired OTG communication mode
(default)

1

Operating elements

* Please switch ON and charge scanner for 3~4 hours at first

time before use.

How to Connect to Smartphone via BT

1. Make sure the default is BT mode (below right, page #1) & your

device supports BT HID or SPP profile

2. Turn off Power-Saving mode on your smartphone/tablet

3. Then, choose HID or SPP profile and scans the following 2

settings codes before connecting to smartphone/tablet.
(A1  A2 or B1  B2)

If you don’t know which profile to choose for your device, try HID

first, then, SPP.

HID profile

SPP profile

A1

Demo

B1

A2

Demo

B2

Demo

1. click the “Settings”

2. click “General”

3. click “Bluetooth”

4. Turn it ON, and search the

Devices

5. Select “Rxxxxxx” to connect

6. When see the “Connected”

means the connection is OK.

(example: pairing with iPhone)

4. Please complete the connection procedures as the above

photos.

5. After the devices are paired, the screen will show

“Connected”. (see step #6 above)

6. Before using WordPad file or appropriate APP, please set

keyboard language of device to US English. Then, scan the
barcodes and the barcode data will show on the cursor side. If
the data cannot be sent to smartphone/tablet, please scan the

“Reset Configuration to Defaults” setting codes (on page #3)..

Notes 1:

* This product complies with Bluetooth standards. This device used

with this product must support the same SPP or HID standard. For
Bluetooth devices with other profiles we cannot guarantee a
connection before the product has been tested.

* The communication speed and range of the product may vary due to

obstacles and radio interference between the product and device.
Condition on the host device may also effect the communication
speed and range of the scanner

Note 2:

* When the battery power is too low, the Orange LED will flash

and beep once. Scanner should be charged immediately. If
scanner shuts down it is recommended to charge it fully then
power it back on.

Trigger / Power ON
Button

(For iOS Device ONLY)
Press the trigger for 4~5
seconds to raise and
lower soft-Keyboard

Exit
Window

Micro USB port (OTG)
Use Micro USB cable to
connect to smartphone.

Charging
cradle

Indicator
(LED)

Before entering BT mode, you
must switch to right “C”
(Charging mode) first.

Then, cradle can supply
power to iOS / Android device
(through micro USB cable) &
scanner simultaneously.

Indicator (LED)
Please check the “LED
Indicator Information” on
page #4

2