RIOTEC LS6303X, LS6323X Programming Quick Manual
r
–
k
x
x
g
g
Programming Quick Guide
Getting Started
Power up the computer once the scanner is fully connected.
Connecting the Scanner
USB Connection : USB(HID)
Auto-sensing setup (For LS6323X Only)
The auto-sensing will active
while scanner position on stand.
When scanner remove from
stand will become trigger mode.
LS6303X/LS6323X.
Standard Product Defaults
The following bar code resets all standard product default settings.
Standard Product Defaults
Trigger
The following bar codes will allow you to use the scanner in Manual Trigger -
Normal Mode (need to press the trigger to read) or Presentation mode (the
scanner is activated when it “sees” a bar code).
Manual T rigge
(Default)
Normal
Presentation Mode
Streaming Presentation™
When in Streaming Pres entation mo de, the s canner lea ves the scan il luminati on
on all the time and continuously searches for bar codes.
Streaming Presentation Mode
Keyboard Country (For USB HID Only)
Scan the appropriate country code as b elow to pr ogr am th e k eyboar d la yout f or
your country or language. As a general rule, the following characters are
supported, but need special car e for c ountries oth er than th e United Stat es: @
| $ # { } [ ] = / ‘ \ < > ~
Suffix
If you want a carriage return after the bar code, scan the Add CR Suffix bar
code. To add a tab after the bar code, scan the Add Tab Suffix bar code.
Otherwise, scan the Remove Suffix bar code to remove the suffixes
Add CR Suffi
Remove Suffi
1D Symbologies -1
ENABLE Codabar DISABLE
ENABLE Code 39
ENABLE
ENABLE Code 32
Code 39
Full ASCII DISABLE
Add Tab Suffix
DISABLE
DISABLE
Barcode Scanner Reading Techniques
The view finder projects an
aiming beam that should be
centered over the bar code, but it
can be positioned in any direction
for a good read.
Hold the scanner over the bar code, pull the trigger, and center the
aiming beam on the bar code.
The aiming beam is smaller when the scanner is closer to the code
and larger when it is farther from the code. Hold the scanner close to
smaller bar codes, and farther away from large bar codes to get a
proper read.
If the bar code is highly reflective (e.g., laminated), you may need to
tilt the scanner at an angle so the bar code can be scanned.
USA(Default)
Belgium
Finland
Germany/
Austria
Italy
Spain
Demar
France
Great Britain
Norway
Switzerland
ENABLE
ENABLE
ENABLE
ENABLE
ENABLE
Interleaved
2 of 5 DISABLE
NEC 2 of 5
DISABLE
Code 93
DISABLE
Strai
ht 2 of 5
Industrial DISABLE
ht 2 of 5
Strai
IATA DISABLE
1
ENABLE
T
1D Symbologies -2
Matrix
2 of 5 DISABLE
1D Symbologies -3
ENABLE
GS1 DataBar
Omnidirectiona DISABLE
2D Symbologies -2
ENABLE Codablock A
ENABLE Code 11 DISABLE
ENABLE Code 128 DISABLE
ENABLE GS1-128 DISABLE
ENABLE Telepen DISABLE
ENABLE UPC-A DISABLE
ENABLE UPC-E DISABLE
ENABLE EAN-13 DISABLE
ENABLE EAN-8 DISABLE
ENABLE
Limited DISABLE
GS1 DataBar
GS1 DataBar
ENABLE
Expanded DISABLE
rioptic
ENABLE
Code DISABLE
* If you are going to scan Code 32, Trioptic Code must be off.
ENABLE Codablock F
ENABLE PDF 417
Micro
ENABLE
PDF 417 DISABLE
ENABLE QR Code
ENABLE Data Matrix
ENABLE Maxi Code
ENABLE Aztec Code
Chinese Sensible
ENABLE
(Han Xin) Code DISABLE
DISABLE
DISABLE
DISABLE
DISABLE
DISABLE
DISABLE
ENABLE MSI DISABLE
Information in this document is subject to change without notice.
For more information, please visit:
www.riotec.com.tw
R_151104_02
2
Loading...