Riotec iCR6307ABQ, iCR6307ABM Programming Quick Guide
g
/
Programming Quick Guide
-iCR6307ABQ/iCR6307ABM
Connecting the Scanner
Be sure that PC is turned OFF, before Connect scanner cable to
the PC USB port on the PC as below described, Ensure that all
connections are ready, and turn on your PC.
1. Please switch ON and charge scanner for 4~5 hours at first time
before use. Scanner switch shown on Fig. 2.
2. After switch ON, the Orange LED will flash following with 3
beep-sounds. The RED LED will be OFF while it links to cradle
within 2.4GHz radio range.
3. If RED LED is continual ON, please re-plug USB cable, then, scan
the 3 barcodes on the bottom of cradle sequentially. (Shown on
Fig. 3 From 1 to 3).
4. Charging issue: Cradle works as charger when putting scanner on
it. Even if the scanner's battery is full, the cradle will continue to
supply power to the scanner. We suggest you to remove scanner
from cradle when scanner is charged fully
* Note: Please install PL-2303 driver for iCR6307ABM
LED Indicator Information
Orange LED ON Full charged
Orange LED Flashing Charging / Low battery
Red LED ON Offline / out of service
Green LED ON Good read
Orange LED ON Good read (Batch mode)
Remark:
* When the battery power is too low, the Orange LED will flash and beep
once. Scanner should be charged immediately.
* If scanner shuts down it is recommended to charge it fully before
turning it back on.
* Under power-saving mode, there will no t be LED indication when charging.
Reset Configuration to Defaults
(scan from A1 to A7 for iCR6307ABQ or B1 to B7 for iCR6307ABM)
iCR6307ABQ
A1
A2
A3
A4
A5
A6
A7
* Note: Please install PL-2303 driver for iCR6307ABM
iCR6307ABM
B1
B2
B3
B4
B5
B6
B7
1
There are two operating modes on the scanner
It is a necessary to scan “clean memory data" when
switching between these two modes.
Wit h i n 2.4GHz ra d i o r a n ge Beyond 2.4GHz radio range
Data
T ransmit data to PC/terminal
read
directly
Enter Data Storage mode
Green/ Orange LED flashes
LED
followed by 3 beeps.
It is a necessary to scan “clean memory data" when switchin
between these two modes.
Save data directly to scanner’s memory, It will transmit th e data to PC
Data
terminal after you scan the Transmit memory data code. To delete
read
data please scan the Clean memory data code.
Enter Data Transmission mode
LED Green/Orange LED flashes followed by 3 beeps.
Always Clean memory data before switching to Data Transmission
Mode.
Otherwise Red/ Orange LED will flash with one long beep and will not
switch modes.
1.Data Transmission mode (Default)
2.Data Storage mode (Batch Mode)
Save data into scanner’s memory,
scanner will transmit data to PC/
terminal automatically when back to
2.4GHz radio range.
Under Data storage Mode
The data can be keep or delete by option after transmit
Keep the data
(Default)
Transmit memory data
Green/Orange LED Flashes foll owed by 3 beeps
Clean memory data
Green/Orange LED flashes foll o w e d by 3 b e e p s
The barcode data which is stored in the memory will be deleted.
Delete the data
Trigger Mode
Trigger always
(T rigger available at any time)
Trigger standard
(Trigger available, after data sent to the device)
(Default)
Transmission Speed
Transmission speed is dependent on your device. In order not to lose
data, please choose the correct speed. Middle-speed is the Default.
High-speed Ultra Slow-speed
Transmission 1 transmission
Middle-speed Ultra Slow-speed
Transmission
(Default)
Slow-speed Ultra Slow-speed
Tra nsm is si on 3 transmission
2 transmission
Wireless Auto-connection
Wireless Auto-connection ON:
When out of range, it will keep trying to connect to
device, scanner will not enter power-saving mode.
Wireless Auto-connection OFF:
When you are out of BT signal range, scanner will stop
sending auto-connection signal to device after 2
minutes. During this time, it will not ent er power-sa ving
mode. Once you ar e back within r an ge, pr ess tr igger t o
connect to the device. (Default)
Keyboard Country(For USB HID only)
Scan the appropriate country code as below to program the keyboard for
your country or language. As a general rule, the following characters are
not supported by the scanner for countries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
USA
(Original setting)
Norway
Germany
Sweden
Denmark
Switzerland
Italian
France
Vietnam
Spain
Portugal
Hungary
Power-saving Mode
Power-saving mode OFF
Power-saving mode ON (Default):
Enter power-saving mode after 1-minute inactivity.
This function converses battery power. When you
press "SCAN/Power ON" button, it will wake up and
* When charging, the scanner will n ot en ter power-saving mode
automatically.
begin to scan.
2
How to append a “prefix” or a “suffix” to the
barcode data
prefix suffix
1. scan above configuration code for Prefix or Suffix
2. enter the required values (right, numeric barcode) for Prefix or
Suffix using the hex values for the desired HEX values from “Prefix
& Suffix TABLE (blew page)”
3. then, end by scanning Code X (below, right)
* The max. of special characters is 5.
* When you append 1~4 required values for Prefix or Suffix, it must
end with Code X.
* It doesn’t need Code X, if you append 5 values to barcode data.
How to delete Prefix or Suffix
1. scan above configuration code for Prefix or Suffix
2. enter the “0” “0” (above, right)
3. then end by scanning Code X (below, right)
0
1
2
3
4
5
Numeric barcode for settings
6
7
8
9
A
B
C
D
E
F
X
Loading...