Rinnai PCD03-EWV Installation Manual

Pipe Cover Installation Instruction

To

the

|jb_th_€

installer

Rinnai

For

your safety, always wear safety glasses

To

use

this product correctly

instructions.
Carefully
Refer

unpack

to

Parts List.

and

identify

and

each component before attempting

Parts List

Q)

Top

Frame

ipc.

Bottom Frame

2pcs.

(D

RJght

and

gloves.

safely, please read

Plate

ipc

\e contact

*

and

follow

Metal Bracket

Rinnai

these assembly

to

assemble.

2pcs.

j(p

4Pcs.

Jd2>

for

model suitability.

and

installation

Plastic Washer

Screw

I0pcs.

M4

2pcs.

Pipe Cover Assembly Instructions

(1)

Assemble

@

washers

(2)

Secure

(3) & (4)

Do not
to

Tighten

with clip

align

the Top

(5) &

the two

with screws

completely tighten

the

the

Frame

©to

(7).

Secure these parts with screws

©.

Bottom Frames

and

plastic washers

the

pipe cover when attaching
screws

at the

bottom

the

Left

(2) to the

screws

of the

and

Left
(9) &

at(Y^)so

to it to the

pipe cover.

@

Screw

Right Plates

and

plastic

and

Right Plates
(f(J).
that

you

water heater.

_6|Ks._

(3)&

will

be

able

CY)

!@_J^ajL\nchor _ 2pcs.

0)

©

(2)

Pipe

Cover

(1)

Remove

sides

of the

(2)

Install

appliance

(3)

Slide

the
appliance. Align
the

Pipe Cover with

of

the

appliance

(4)

Loosen

Then mark

(5)

Remove

marked.
material

Installationj

the

mounting screws

appliance.

the two

Metal

with

the

Pipe Cover

the

screws
the

locations

the

Pipe Cover

For

drywall,

may

require

the

in

'A'< & (B)

Brackets ® to the

screws ® removed

assembly
mounting holes
the

step

1,

on the

drill

alternate

onto

the

and

screws

and

(B)

removed

and

screws

"back" Bottom Frame.

to

attach

the

drill

two

two

3/16-in.

mounting

from

the

bottom

bottom

in

bottom

©.

Pipe Cover

holes

holes (other wall

of the

step

1.

of the

temporarily mount

from

the

to the

in the

wall

details).

and

sides

wall.

as

(6)

Gently

(7)

Slide

(8)

Align

(9)

Tighten

(10)
(11)

(12)

tap the

flush

with

the

the

Pipe Cover assembly onto
appliance.
Cover with
appliance

Tighten screws

cover

Attach
Attach

and

With

appliance,
"back" Bottom Frame.

Align

in

the

back corner

meet.

screws

the

the

plastic washers

the

Pipe Cover flush with

wall anchors

wall.

the

mounting holes

the

screws

step

1,

and

(Tl),

but

(9)

at

(y) and

Pipe Cover
Front Panel

(8) & ®.

tighten

the

into

(Bj)

removed

screws

leave

at @ where

to the

screws

Cfi).

screws®

screws

wall with

(5) to the

the

on the

the

drilled holes until

the

bottom

and

from

loose.

the

water heater case

(B).

two

Pipe Cover with screws

attach
the

sides

screws©.

of the

the

Pipe

of the

and

pipe

2)

U287-1040x02(00