Rinnai Energysaver RHFE-556FTR, Energysaver RHFE-556FDT, Energysaver RHFE-557FTR, Energysaver RHFE-1004FTR, Energysaver RHFE-1004FDT Operation And Installation Manual
Page 1
Please note:
Flue System Installation Instructions
enclosed with Flue Terminal packaged
separately.
This appliance shall be installed in accordance with:
• Manufacturer’s Installation Instructions
• Local Gas Fitting Regulations
• Municipal Building Codes
• AS/NZS 5601 Gas Installations, AS/NZS 3000 Wiring Rules
• Any other relevant Statutory Regulations
This appliance must be installed, serviced and removed by an authorised person.
All Rinnai gas products
are A.G.A. certified.
Energysaver® Space Heaters
Operation and Installation Manual
To Suit Models:
RHFE-556FTR / RHFE-556FDT
RHFE-557FTR
RHFE-1004FTR / RHFE-1004FDT
Page 2
Rinnai Australia ii Energysaver® - Operation & Installation Manual
INSTALLATION REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
CERTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
CARTON CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
INSTALLATION RECORD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SAFETY DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
ABOUT YOUR ENERGYSAVER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
CUSTOMER INFORMATION - CONTROL PANEL. . . . . . . . . . . . . . . . . . . . . . . . . .11
REMOTE CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CUSTOMER INFORMATION - OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
FDT Models Only .........................................................................................................16
Fixed Time Period Operation for FDT Models only: .....................................................16
How to Operate the FDT Models Only .........................................................................16
To Turn the Unit ‘ON’ ...................................................................................................16
To Turn the Unit ‘OFF’ .................................................................................................17
Adjusting the Temperature ...........................................................................................17
SETTING THE CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Operating the Timers ...................................................................................................19
Set and Forget Operation ............................................................................................19
OPERATING THE TIMERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Pre-Heat .......................................................................................................................20
Humidifier Tray .............................................................................................................20
Outside Flue Terminal ..................................................................................................20
OTHER OPERATING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Cleaning .......................................................................................................................21
Fan Filter ......................................................................................................................21
CARE OF YOUR ENERGYSAVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
ERROR MESSAGES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
INSTALLATION MANUAL - TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . .26
CONTACT INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
TABLE OF CONTENTS
Page 3
Rinnai Australia 1 Energysaver® - Operation & Installation Manual
INSTALLATION REQUIREMENTS
This heater must be installed by an authorised person. The insta llation must conform to local regulations.
The installation must also comply with the instructions supplied by Rinnai.
Service and removal must be carried out by an author i sed pe rso n .
The Rinnai Energysaver
®
Range have been certified by the Australian Gas Association.
The AGA Certification Number is shown on the appliance dataplate.
No parts or functions should be modified or permanently removed from the heater.
Please keep these instructions in a safe place for future reference.
Check you have the following:
1 x Rinnai Energysaver Space Heater - Model either:
RHFE-556FTR/FDT, RHFE-557FTR, RHFE-1004FTR or RHFE-10 04FDT
1 x Rear Cover set, comprising of left, right and top cover panels
1 x Bolt pack containing;
• Stainle ss steel sheath clamp
• 2 x securing brackets
• 2 x 8g x 30 mm stainless steel securing bracket screws
• 2 x plastic inlet hose clamps
• 1 x 150 mm long cable tie
• 1 x HD stainless steel flue clamp
• 2 x 6g x 10 mm button head screws
• 4 x 6g x 8 mm pan head screws.
For Flueing details, please refer to seperate Energysaver Co-Axial Flueing Installation
Manual’.
IMPORTANT
CERTIFICATION
CARTON CONTENTS
Page 4
Rinnai Australia 2 Energysaver® - Operation & Installation Manual
INSTALLATION RECORD
INSTALLERS / GAS FITTERS DETAILS
Installers Name: ____________________________________________________________________
Company Name: ____________________________________________________________________
Company Address: ____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
Company Contact Details
Telephone: ____________________________________________________________________
Mobile Phone: ____________________________________________________________________
Certificate of Compliance / Certification Number: _____________________________________________
Authorised Persons - Licence Number: _____________________________________________________
Installers Signature: ____________________________________________________________________
Installation Date: ____________________________________________________________________
APPLIANCE DETAILS
Model Number: ____________________________________________________________________
Serial Number: ____________________________________________________________________
Installation Address: ____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
Page 5
Rinnai Australia 3 Energysaver® - Operation & Installation Manual
• Failure to comply with these instructions could result in a fire or explosion,
which could cause serious injury, death or property damage.
• Improper installation, adjustments, service or maintainence can cause serious
injury, death or property damage. Such work must be performed by an
authorised person.
• The appliance must be installed in accordance with the local gas and electrical
authority regulations.
• For information on gas consumption, see data plate on the appliance.
• This appliance must not be installed where curtains or other combustible
materials could come in contact with it. In some cases curtains may need
restraining.
• When considering installation ensure minimum clearances as follows are
adhered to.
• Heat radiating from the front of the heater
may over time affect the appearance of
some materials used for flooring such as
carpet, vinyl, cork or timber. This effect
may be amplified if the air in the room
contains cooking vapours or cigarette
smoke. To avoid this possibility, it is
recommended that a mat or similar
protective sheet be placed in front of the
appliance, extending at least 750 mm in
front of the air outlet.
• The appliance is not intended for use by young children or infirm persons
without supervision.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensor or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instructions
concerning use of this appliance by a person responsible for their safety.
• These appliances are not intended for use by young children or infirm persons
without supervision.
• Y oung children should be supervised when in the vicinity of these heaters while
in operation.
• If the supply cord is damaged or require replacing, it must be replaced by the
manufacturer or the manufacturer's agent or similarly qualified person in order
to avoid a hazard.
• This heater must not be located immediately below a power socket outlet.
• DO NOT connect to an LPG Gas cylinder indoors.
• A dedicated 240 V earthed 10 Amp power point must be used with this
appliance.
• DO NOT modify this appliance. Modifying it in any way or form, from original
specifications may create a dangerous situation and will void your warranty.
• Only the flue components specified by Rinnai must be used.
• Unpack the heater and check for damage. DO NOT INSTALL DAMAGED
HEATER. If the heater is damaged, contact your supplier for advice.
• Before installing the heater, check the label for the correct gas type (see rating
plate, right hand side panel).
• Refer to local gas authority for confirmation of the gas type if you are in doubt.
WARNING
AT LE A S T
750 mm
SAFETY
Page 6
Rinnai Australia 4 Energysaver® - Operation & Installation Manual
DO NOT allow children to post articles in the
louvres.
The appliance is not intended for use by
young children or infirm persons without
supervision.
Young children should be supervised to
ensure they DO NOT play with the appliance.
DO NOT allow children or elderly persons to
sleep in the warm air discharge from the
heater.
DO NOT cover or place articles on this
heater.
Turn ‘OFF’ heater after use.
SAFETY
Page 7
Rinnai Australia 5 Energysaver® - Operation & Installation Manual
Keep away from flammable materials.
Combustible materials must not be placed
where the heater could ignite them.
DO NOT place articles on or against this
appliance.
DO NOT use or store flammable materials
near this appliance.
DO NOT spray aerosols in the vicinity of this
appliance while it is in operation.
Most aerosols contain butane gas which can
be a fire hazard if used near this heater when
it is in use.
DO NOT sit on this heater.
DO NOT place articles in front of the louvres.
DO NOT unplug the heater while it is in
operation or while the fans are still cycling.
DO NOT turn the heater ‘OFF’ by unplugging
it from the wall.
SAFETY
Page 8
Rinnai Australia 6 Energysaver® - Operation & Installation Manual
DO NOT place containers of liquid on top of
the heater. Water spillage can cause
extensive damage to the appliance and may
result in electric shock.
A dedicated 240V 10 Amp power point be
used with this appliance.
DO NOT use power boards or double
adaptors to operate this appliance.
Heater must not be located below a power
socket-outlet.
This appliance must not be built-in
The clearances must be maintained.
Access panel and Humidifier tray have to be
fitted while the heater is in use.
Rinnai recommend you fill the tray to the
water level indicator as marked. Take care
not to overfill.
Heat emanating from the front of this
appliance may over time affect the
appearance of some materials used for
flooring such as carpet, vinyl, cork or timber.
This effect may be amplified if the air in the
room contains cooking vapours or cigarette
smoke. To avoid this possibility, it is
recommended that a mat be placed in front of
the appliance, extending at least 750 mm in
front of the air outlet.
1000 mm
50 mm
50 mm
50 mm
2
5
0
m
m
TOP
FRONT
LEFT SIDE RIGHT SIDE
WATER LEVEL
Pull
Humidifier Tray
W
A
TER
L
E
V
EL
Gently Remove
Access Panel
Pull
AT LEAST
750 mm
SAFETY
Page 9
Rinnai Australia 7 Energysaver® - Operation & Installation Manual
During peak operating periods the filters
should be cleaned weekly, however if the
“FILTER” warning indicator flashes in the
control panel display, turn off the appliance
immediately and clean filters before further
use.
When the heater is operated for the first time
or after long periods of non use a slight odour
may be emitted, this is normal.
However if odours persist switch off the
appliance and contact Rinnai.
Keep flammable materials, trees shrubs etc.
away from the flue terminal.
Snow Areas - in areas subject to heavy
snowfall, keep snow clear of flue terminal at
all times.
Servicing shall be carried out only by an Authorised Person
Filter
ON
IMPORTANT
SAFETY
Page 10
Rinnai Australia 8 Energysaver - Operation & Installation Manual
Overheat Switch:
This device automatically cuts the gas off if the heater exceeds a predetermined temperature.
This is normally caused by an obstruction in front of the louvres, or a blocked fan filter.
If this switch operates, turn the unit OFF, r emove the obstruction (clean filters) and let the unit cool off
before re-operating.
Two Fusible Links:
Backs up the overheat switch. If a fusible link cuts the gas off, a service call is required to repair the
appliance replace the link.
Flame Failure Device:
If the flame goes out during operation this device cuts the unit off (locko ut). To reset, turn the unit ‘OFF’,
then ‘ON’ again. If this happens repeatedly a service call is required.
Fan Switch:
Turns the fan on automatically when the heat exchanger warms up and off when it co ols down.
This helps to prevent cold draughts and maximises efficiency.
Electrical Fuse:
The electrical circuits are protected by an electric fuse. Whe n the fuse blows, the he ater will not operate.
The fuse must be replaced by an authorised person.
Power Failure:
In the event of a power failure or power cut, the gas valves will automatically close. After the power is
re-instated the appliance must be re-started manually.
Rinnai Australia has a service and spare parts network in all states. Our service network personnel are
fully trained and equipped to give the best service on your Rinnai appliance. If your appliance needs
servicing, please ring one of the service contact numbers on the back of this booklet.
Rinnai recommend that this appliance be serviced every 2 years.
SAFETY DEVICES
SERVICE
Page 11
Rinnai Australia 9 Energysaver® - Operation & Installation Manual
ROOM SEALED
Air for combustion is taken from the outside and the flue
product are exhausted to the outside. This means heater
operation has no effect on the composition and quality of air in
the room.
PUSH BUTTON IGNITION
Only one touch of the ‘ON/OFF’ button is required to operate
the heater.
FUNCTION / CHILD LOCK
Prevents children from altering heater settings whilst running,
or from activating the heater when turned OFF.
MEMORY
The micro-computer records selected programming
temperatures, the Timer, and Economy/Auto-Off and Pre-heat
modes. Even if the power cord is pulled out of the power point,
the next time the unit is operated, there will be no need to reprogram these parameters. (Only the clock will need to be reprogrammed).
7 STEP AUTOMATIC HEAT
CONTROL
With electronic thermostat. The fan is also controlled by the
thermostat.
PRE-HEAT
This function operates automatically in conjunction with the
Timers. When a Timer is selected, the heater may operate
anywhere within an hour prior to the programmed starting time
of a Timer.
This function is called Pre-heat since it ensures the room
reaches the desired temperature by the time the Timer
programs ON time. The room temperature is sensed one hour
before reaching Timers programmed ON time.
The temperature differential at the time of sensing the room
temperature combined with the data from previous operation
governs exactly how long before the programmed ON time the
micro-computer will operate the heater and ignite the burner.
ECONOMY MODE
The Economy (ECON) function is an energy saving features
designed to control the room temperature and prevent
discomfort from over heating.
OVERRIDE FUNCTION
This temporarily changes the heater operation from ON to OFF,
or vice versa, until the next programmed setting is reached.
REMOTE CONTROL
A remote control is supplied to enable you to turn your heater
‘ON’ and ‘OFF’, and to adjust its temperature at your
convenience. The remote control also comes with its own
handy bracket for easy storage.
DUAL TIMER
The Dual Timer allows you to program the applia nce to come
on for two separate periods each day, one period in the
morning and one period in the evening, user the Timer 1 and
Timer 2 functions.
The Dual Timer feature means that you can "Set and Forget"
your heater. It will turn itself ON at the times you have
programmed until you cancel the Timer program.
HEATER FILTER INDICATOR
When the heater filter becomes covered with dust the heater
filter indicator will flash. The filters should be vacuumed at
regular intervals to avoid unnessary strain on the appliance.
HUMIDIFIER TRAY
The integral humidifer tray can be filled with water as required
to raise the humidity level in the room for extra comfort. Tray
should not be filled to more than 3/4 full.
FEATURES
Page 12
Rinnai Australia 10 Energysaver® - Operation & Installation Manual
RHFE1004FTR / FDT RHFE557FTR RHFE556FDTRHFE556FTR
E
L
L
I
J
K
K
I
G
G
F
F
E
E
D
D
B
C
C
C
A
F
A
A
B
D
H
H
J
H
L
K
J
G
A
C
D
E
F
G
I
H
L
K
J
G
I
G
Exhausts flue products to the outside of
the building, via the flue system
(purchased separately).
EXHAUST OUTLET
Carries air for combustion, via
the flue system (purchased
separately).
AIR INLET TUBE
I
H
Helps to protect the interior of the
appliance & fan from dust particles.
AIR FILTER
G
J
ROOM TEMPERATURE SENSOR
K
GAS CONNECTION
L
ELECTRICAL CORD
Operation / Temperature Control
Display and Appliance error codes
CONTROL PANEL
B
REMOTE CONTROL BRACKET
A
'ON' / 'OFF' SWITCH
C
Built into the warm air discharge duct.
Humidifies the warm air flow.
HUMIDIFIER TRAY
E
Pulls OFF to allow filing of
humidifier tray.
BOTTOM TRIM
F
D
Warm air discharge duct.
LOUVRE
ABOUT YOUR ENERGYSAVER
Page 13
Rinnai Australia 11 Energysaver® - Operation & Installation Manual
Models: RHFE-556FTR / RHFE-557FTR
Set Room
Filter
Clock
Timer 1
Timer 2
Function/
Child Lock
Economy Timer 1 Timer 2 Override
Set Times
ON / OFF
AM
PM
ON
Temp
Time
Main switch for turning 'ON / OFF'.
'ON' / 'OFF' BUTTON
1
Helps prevent accidental operation
as well as small children from
altering controls.
FUNCTION / CHILD LOCK
BUTTON
7
Indicates that the override function
is activated.
OVERRIDE INDICATOR
6
6 3
Indicates Function lock is activated.
FUNCTION / CHILD LOCK
INDICATOR
8
8
10
11
Selects clock and/or Timers for
adjusting or programming.
SET TIMES BUTTON
2
2
Selects operating mode for Timer 1
or Timer 2.
TIMER ACTIVATION
BUTTONS
12
Indicates that Timer 1 or Timer 2
has been selected to operate.
TIMER ACTIVATION
DISPLAY
13
Indicates that clock or dual timer
programme is being set.
CLOCK ADJUSTMENT &
TIMER INDICATORS
Indicates that the filter needs cleaning.
FILTER INDICATOR
15
9
16
REMOTE CONTROL RECEIVER
Indicates that the Economy mode
is in operation.
ECONOMY BUTTON
11
ECONOMY INDICATOR
Selects energy saving function.
Shows either time of day, temperature
or coded error messages.
TIME / TEMP DISPLAY
3
4
Used to adjust temperature and time
settings.
TIME / TEMP ADJUSTMENT
BUTTON
4
5
5
This function is used to manually
override the current operation of the
heater.
OVERRIDE BUTTON
1
12
13
107
14 159 16
Indicates that appliance is turned
'ON' & whether the burner is alight.
POWER 'ON' /
COMBUSTION INDICATOR
14
on
off
CUSTOMER INFORMATION - CONTROL PANEL
Page 14
Rinnai Australia 12 Energysaver® - Operation & Installation Manual
Model: RHFE-1004FTR
Function Lock
Room
AM
PM
Timer 2
Override
Economy
Set
Temp
Time
Timer 1
Set Times
ON / OFF
Clock
Timer 1
Timer 2
5
10
11
7
2
8
1
9
12
3
4
13
6
Filter
ON
Main switch for turning 'ON / OFF'.
'ON' / 'OFF' BUTTON
1
Helps prevent accidental operation
as well as small children from
altering controls.
FUNCTION / CHILD LOCK
BUTTON
7
Indicates that the override function
is activated.
OVERRIDE INDICATOR
6
Indicates Function lock is activated.
FUNCTION / CHILD LOCK
INDICATOR
8
10
Selects clock and/or Timers for
adjusting or programming.
SET TIMES BUTTON
2
Selects operating mode for Timer 1
or Timer 2.
TIMER ACTIVATION
BUTTONS
12
Indicates that Timer 1 or Timer 2
has been selected to operate.
TIMER ACTIVATION
DISPLAY
13
Indicates that clock or dual timer
programme is being set.
CLOCK ADJUSTMENT &
TIMER INDICATORS
Indicates that the filter needs cleaning.
FILTER INDICATOR
15
9
16
REMOTE CONTROL RECEIVER
Indicates that the Economy mode
is in operation.
ECONOMY BUTTON
11
ECONOMY INDICATOR
Selects energy saving function.
Shows either time of day, temperature
or coded error messages.
TIME / TEMP DISPLAY
3
Used to adjust temperature and time
settings.
TIME / TEMP ADJUSTMENT
BUTTON
4
5
This function is used to manually
override the current operation of the
heater.
OVERRIDE BUTTON
Indicates that appliance is turned
'ON' & whether the burner is alight.
POWER 'ON' /
COMBUSTION INDICATOR
14
15
14
on off
16
CUSTOMER INFORMATION - CONTROL PANEL
Page 15
Rinnai Australia 13 Energysaver® - Operation & Installation Manual
RHFE-556FDT
* Flashing LED is room Temperature
Steady LED is selected Temperature
Model RHFE-1004FDT
ON
OFF
LO
HI
16 18 20 22 24 26
4
Temperature Control
3
1
Filter
ON
15
14
ON / OFF
1
Function Lock
Temp
7
8
4
Economy
10
11
Set Temp
Room Temp
Filter
ON
15
14
3
CUSTOMER INFORMATION - CONTROL PANEL
Page 16
Rinnai Australia 14 Energysaver® - Operation & Installation Manual
Remote Control
The Remote Control will not turn the heater ‘ON’ if Timer(s) have been selected.
To manually operate when Timer(s) are not selected, simply press the ‘ON’ or ‘OFF’ button. or
To alter the temperature at anytime while the heater is operating, simply press the “” or “” buttons.
• Only use battery type specified (CR 2032). .
• Remove the battery if control is not going to be used for a long period. This
will help avoid damage from leaking batteries.
• The remote control will not function if the heater is in Timer mode.
• If the heater is in Override mode, switching ‘ON’ or ‘OFF’ will cancel any future
timer operations, these will have to be reset manually.
• Some fluorescent lights may interfere with the transmission of remote control
signals, in this case changing the position from which you are operating the
remote control may help.
• Avoid leaving the remote control in direct sunlight and do not place close the
the louvres of the heater.
• Avoid getting the remote control wet or dropping it.
1
2
3
Operates the heater manually.
'ON' BUTTON
1
Stops heater manually.
'OFF' BUTTON
2
Increases or decreases the
temperature setting.
TEMPERATURE
ADJUSTMENT
3
Power source for operating remote
control.
BATTERY
4
1
2
3
4
BATTERY REPLACEMENT
Open the back of the remote
control and replace Lithium battery.
TYPE: CR 2032
5
5
PLEASE NOTE: NOT USED ON THE ‘FDT’ MODEL ENERGYSAVERS
NOTE
5
4
REMOTE CONTROL PANEL
Page 17
Rinnai Australia 15 Energysaver® - Operation & Installation Manual
IMPORTANT:
You must read and understand these instructions fully before operating the heater.
• To turn the unit ‘ON’
Press the ON/OFF button to operate the heater. The ON indicator will glow green. The spark
generator will be heard before the burner ignites and the ON indicator glows red, indicating that the
heater is alight.
When the heater warms up, the fan will automatically start.
If the heater does not ignite on initial use, this may be due to air remaining in the gas supply
line. The spark generator will only continue for 15 seconds. After this it will be necessary to
press the ON/OFF button OFF, then ON again.
If the appliance fails to ignite after 4 attempts, contact Rinnai as a service call may be required.
• To turn the unit ‘OFF’
Simply press the ON/OFF button to switch off the heater. The ON indicator light will go out. The
Fan will continue to operate for several minutes after the burner has gone out in order to cool the
appliance. Do not unplug the appliance while the fan is running. The convection fan will continue to run
until the appliance cools.
• Room Temperature Adjustment
The room temperature and pre-set temperatures can only be displayed and adjusted when the heater
is running.
Press the “” button to increase the temperature setting or “” button to decrease the
temperature setting.
The temperatures can be preset to:
a) [L] low - continuous combustion on low.
b) [16°C] to [26°C] in 1°C steps - thermostatic control to preset te mp selected . Combus tion rate
varies as required to maintain the selected temperature.
c) [H] - continuous combustion on high.
• If the heater does not ignite then the pre-set temperature may not be set to a setting which is
higher than the room temperature. The ON indicator will change colour from red to green when
the heater reaches the pre-set temperature and stops running.
• Economy Mode
The Economy (ECON) function is an energy saving features designe d to control the r oom temperatu re
and prevent discomfort from over heating.
1. The Economy mode can only be operated when the heater is turned ON, but remains in the system
memory once set until deactivated. Selected the Economy mode before selecting time operation.
2. Press the Economy button to start the Economy function. The Economy indicator will glow.
3. Press the Economy button once more to switch OFF th e fu nction.
• Child Lock / Function Lock
The lock function will help to prevent accidental operation as well as small children from
altering the controls. To operate the lock simply press the LOCK button. The function is
activated immediately and the LOCK indicator will gl ow.
To Deactivate the LOCK simply press the LOCK button for 3 seconds and the LOCK indicator
will go out. The LOCK can be deactivated at any time in this way.
Set Room
on
off
Filter
Clock
Timer 1
Timer 2
Child Lock Economy Timer 1 Timer 2 Override
Set Times
ON / OFF
AM
PM
ON
Temp
Time
2
1
5 4107
6 148 11
Filter
ON
15
14
16
1
1
14
1
1
1
14
4
4
4
14
10
10
11
10
7
8
8
7
8
CUSTOMER INFORMATION - OPERATION
Page 18
Rinnai Australia 16 Energysaver® - Operation & Installation Manual
During normal operation the LOCK may be activated and all controls, other than the OFF switch, will
be locked. Deactivating the LOCK releases the controls. If the LOCK is activated whilst the heater is
turned OFF, then all functions will be locked. If the heater is turned OFF while the LOCK is activated,
it cannot be turned ON again until the LOCK is deactivated.
Override
This function is intended to be used to manually override the current operation of the heater.
For example; if the heater is in standby mode (i.e. bet ween f inis hing time and start in g time of a
Timer) and the OVERRIDE button is selected, then the heater will begin to operate and heat
the room.
• To operate the OVERRIDE simply press the OVERRIDE button. The OVERRIDE indicator
will flash.
To manually deactivate the OVERRIDE simply press the OVERRIDE button again. The
OVERRIDE indicator will go out, and the heater will return to standby mode.
• The heater will continue to operate on OVERRIDE until the OVERRIDE button is pressed again,
or one of the Timers takes over the operation of the appliance. This means that the OVERRIDE
mode will automatically drop out if a programmed starting time is reached.
• The appliance will then return to operating at times programmed into the Timer(s).
FDT Models Only
Fixed Time Period Operation for FDT Models only:
• The Energysaver RHFE-556FDT or RHFE-1004FDT includes an option so that operation of the
appliance automatically stops after a fixed time period.
• It is possible to choose any one of seven time periods. The periods are: 1, 2, 3, 6, 8, 10 or 12
hours.
• This option must be activated by a qualified person or trained Rinnai service person.
• Fixed time period operation is ideally suited to classroom situations, clubs, meeting halls, and other
areas where a limit is required on the length of time the appliance operates.
• The feature can provide substantial energy savings in cases where u sers are likely to fo rget to turn
the appliance OFF when they leave the room after meetings or lessons.
• If a power failure occurs at any time during operation, the appliance will remain OFF once the
power is re-instated. The ON / OFF button must be pressed to re-ignite the appliance.
• Contact Rinnai on the number listed on the back cover of this manual for further advise.
How to Operate the FDT Models Only
To Turn the Unit ‘ON’
• Press the ON/OFF button to operate the heater. The ON indicator will glow green. The
convection fan will rotate. Ignition will take 5 ~ 10 seconds and the ON / Combustion indicator will
change from green to red to let you know that the burner has ignited.
• Note: When using the unit for the first time or after long periods of disuse, ignition may not occur
the first time it is operated as there may be air in the gas pipes. If ignition does not occur after
approximately 30 seconds the unit will cease operation automatically.
• Try operating the unit again if this occurs.
5
5
5
6
5
6
5
1
1
• The unit may make noises after ignition / extintion. This is inside of the unit
expending and contracting and is normal.
• The heater will not ignition if the ON/OFF button is pressed straight after
extinction. After approximately 20 seconds has passed, the unit will
automatically go into ignition mode.
NOTE
CUSTOMER INFORMATION - OPERATION
Page 19
Rinnai Australia 17 Energysaver® - Operation & Installation Manual
To Turn the Unit ‘OFF’
• Press the ON/OFF button to switch off the heater.
• The ON / Combustion indicator will go out.
• After the indicator has gone out, the convection fan will continue to rotate for several minutes, then
stop. This is to lower the temperature within the unit. DO NOT pull out the power cord during this
time.
Adjusting the Temperature
Displaying, setting and adjusting the room temperature can only be done wh en the unit is operating.
• When the unit is first operated, the room temperture is set at 22°C.
• Set the desired room temperature will the up and down buttons while looking at the display section.
• The “Set Temp” can be set to “L” or between “16” ~ “26”, or “H” (continuous combustion on High).
• The “Room Temp” will display “L” (when lower than 1°C), “1” ~ “30” (at intervals of 1°C), or “H”
(when higher than 30°C).
• Once a temperature is set, it will be stored in the microcomputer’s memory.
1
• DO NOT pull out the power cord or disconnect the power during combust ion to
cause extinction, or straight after extinction, as this may cause damage to the
unit.
CAUTION
• When the Function Lock is set, the Function Lock indicator will continue to
illuminate even when the unit is OFF and the Function Lock will not be
cancelled.
NOTE
• Rooms may not arrive at the set temperature due to the construction of the
room, the location of the unit, or external temperatures.
• If the heater does not ignite then the pre-set tempera ture may not be set to a
setting which is higher than the actual room temper ature. The ON indicat or will
change colour from red to green when the heater reaches the pre-set
temperature and stops running. The heat er will operate at eight minute intervals
to maintain warmth in a room.
NOTE
Page 20
Rinnai Australia 18 Energysaver® - Operation & Installation Manual
Setting the Clock
When the appliance is first plugged in or after a power failure, the digital display with show
--:--
As an example, let’s set the clock to 10:35 am;
Press the SET TIMES button
once, the Clock indicator will flash.
Press and hold the “” button; the minutes will begin to change first then the time will
change by whole hours.
Release the button when AM 10:00 shows on the Digital Display . Confirm that you have
selected AM, a small indicator on the left hand side of the Digital Display indicates the AM
setting.
Press and hold the “” button again, release the button when AM 10:35 shows. If you go
past AM 10:35, then the “” button can be used to change the time settings in reverse.
Press the Timer Set button five times to lock in and complete setting the time. The Clock
and Timer indicators will go out. A small indicator on the Digital Display will flash to show
that the Clock is operating.
Setting the ON / OFF Timers
Before programming the Timers you must ensure that the clock has been set to the
correct time.
As an example, let’s program Timer 1 to heat the room by 7:10 am and finish at 9:00 am.
Press the Set Times button twice. The Digital Display will show AM 6:00. Timer 1
indicator will flash.
Press the “” button until AM 7:00 appears, release the button, then press it again until AM
7:10 appears. (Press the “” button if you go past AM 9:00).
Press the Set Times
button three times to lock in the program time. The Digital Display
will show the current time. A small indicator on the Digital Display
will flash to shown that
the display has returned to the clock.
Timer 2 is programmed in the same way, remember to ensure that the Timer 2 ind icator
is
flashing when you program in the desired setting.
Set Room
on
off
Filter
Clock
Timer 1
Timer 2
Child Lock Economy Timer 1 Timer 2 Override
Set Times
ON / OFF
AM
PM
ON
Temp
Time
24
3 9
13
12
Function Lock
Room
AM
PM
Timer 2
Override
Economy
Set
Tem p
Time
Timer 1
Set Times
ON / OFF
Clock
Timer 1
Timer 2
2
1
9
12
3
4
13
on off
3
2
9
4
3
4
4
2
3
2
3
13
4
2
3
3
13
This procedure is for setting the ON/OFF times for Timers 1 and 2 only. To achieve
the timers refer to details on the following page.
NOTE
SETTING THE CLOCK
Page 21
Rinnai Australia 19 Energysaver® - Operation & Installation Manual
Operating the Timers
The timers can be programmed to operate for any two positions in any 24 hours. Before
operating the Timer(s), the clock time must be correct and a starting time and finishing time
for the Timer(s) must be programmed. The two Timers operate in the same way. This heater
does not commence operation at the programmed starting time. It will attempt to heat a room
by the programmed starting time. See Pre-heat, for further explanation.
To select the Timer(s) to commence heating:
• Check the time shown on the Digital Display is correct.
• Check the ON and OFF times, for both Timers if necessary, (see ‘setting the ON/OFF
timers’).
• Press the ON/OFF button to operate the heater. The ON indicator will glow green.
• Select the desired temperature setting.
Press the Timer 1 and/or Timer 2 button(s). The timer indicator(s) will glow. The heater
will now remain on standby until up to one hour prior to the time programmed into the selected
Timer(s) is reached. When this time is reached, the Timer indicator will flash and the heater
will operate. The ON indicator glows red when the heater commences operation. Actual
start time will depend on temperature selected and current room temperature. (See Pre-heat
section for further details).
Set and Forget Operation
Your heater can be operated to alternate between Timers automatically during cold weather
by selecting Timer 1 and Timer 2
together. Both Timer indicators will glow. The
appliance will remain on standby at intervals between the programmed finishing and starting
times of each Timer. While the heater is operating during programmed intervals the Timer
indicator
will flash.
If there is a power failure, the system memory will retain the Timer programs, and the
clock will stop at the time the power goes off. The clock will start again when the
power comes back on, but the time will be slow by the duration of the power failure. To
set the clock to the correct time after the power has come back on, simply follow the
instructions on page 18.
Set Room
on
off
Filter
Clock
Timer 1
Timer 2
Function
Child Lock
Economy Timer 1 Timer 2 Override
Set Times
ON / OFF
AM
PM
ON
Temp
Time
2 14
3 9
13
12
4
1
Function Lock
Room
AM
PM
Timer 2
Override
Economy
Set
Tem p
Time
Timer 1
Set Times
ON / OFF
Clock
Timer 1
Timer 2
2
1
9
12
3
4
13
on off
3
1
9
4
12
13
14
12
13
13
3
OPERATING THE TIMERS
Page 22
Rinnai Australia 20 Energysaver® - Operation & Installation Manual
Pre-Heat
This function operates automatically in conjunction
with the Timers. When a Timer is selected, the
heater may operate anywhere within an hour prior
to the programmed starting time on the Timer.
This function is called Pre-heat since it ensures the
room reaches the desired temperature by the time
the Timer programs ON time. The room
temperature is sensed one hour before reaching
Timers programmed ON time.
The temperature differential at the time of sensing the room te mperature combined with the data from
previous operation governs exactly how long before the programmed ON time the micro-computer will
operate the heater and ignite the burner.
Humidifier Tray
Your heater is fitted with an enamelled tray behind the air outlet so that you can humidify the air. To fill
the tray, open the door as shown in the diagram and pour water into the tray using the spout built into
the door.
The air wil be humidified as it passes over the water in the tray. DO NOT FILL THE TRAY WHILST THE
UNIT IS IN OPERATION. CLOSE THE DOOR AFTER FILLING.
These are very high efficiency appliances. During operation a small am ount of water is produced in the
flue tubes. This drains into the enamel tray. It is quite normal for a small quantity of water to remain in
the bottom of the tray. If you are using the humidifier, it will need filling about once a day during the peak
heating season.
Vertical Louvre Adjustment
The warm air flow direction may be altered by inserting a screwdriver or similar tool and ge ntly bending
the vertical louvre(s) either to the left or the right. NOTE: These louvres are not desgined to be adjusted
more than 6 times.
RHFE-556FTR/RHFE-556FDT / RHFE-557FTR RHFE-1004FTR / RHFE-1004FDT
Outside Flue Terminal
On cold days steam may be discharged from the flue terminal. This is normal with high efficiency
appliances as such as the Energysaver® range and does not indicate any fault.
WATER LEVEL
Pull
Humidifier Tray
W
A
TER
L
E
V
EL
Gently Remove
Access Panel
Pull
WATER LEVEL
PUSH
Pull
Filler Spout
Access Door
Push down and then
pull to open.
DO NOT force the
door, only open the
door far enough to
access filler spout.
Door must be closed
for operation!
Humidifier Tray
WATE
R
LE
VE
L
OTHER OPERATING INFORMATION
Page 23
Rinnai Australia 21 Energysaver - Operation & Installation Manual
Cleaning
Your heater needs very little maintenance, but the following information will help you to keep it looking
good, and working efficiently.
• Unplug electrical cord before cleaning.
• All parts of the heater can be cleaned using a soft, damp cloth and a mild detergent.
• Do not use solvents to clean any parts.
Fan Filter
To protect the room air fan from dust particles or
lint, a filter is situated at the rear of the appliance.
When this filter becomes blocked, the filter
indicator will flash to indicate that it should be
cleaned. Clean the filter weekly during the heating
season. Dusty filters reduce the air flow through
the appliance reducing heating effectiveness.
• DO NOT remove filter when appliance is
operating.
• When the filter requires cleaning, clean filter
before using the appliance, or whilst the
appliance is not operating.
If you do not clean the filter at regula r intervals
and the filter indicator is allowed to remain
flashing, then the appliance will stop and [14]
will flash on the Digital Display signifying that
the inbuilt safety device has functioned. You
must clean the filter before operating the
heater again.
• DO NOT use the heater with the filter indicator
flashing as this may cause overheating.
• DO NOT not wait for the filter indicator to flash
before cleaning filters.
Ensure to fit the Fan Filter back in the appliance after cleaning.
DO NOT operate appliance without filter in place.
Regularly check the outside flue terminal to make sure it is clear from plant growth and from other
obstructions. Refer “SAFETY” on page 2 for additional requirements.
Set Room
on
off
Filter
Clock
Timer 1
Timer 2
Child Lock Economy Timer 1 Timer 2 Override
Set Times
ON / OFF
AM
PM
ON
Temp
Time
1
15
Function Lock
Room
AM
PM
Timer 2
Override
Economy
Set
Tem p
Time
Timer 1
Set Times
ON / OFF
Clock
Timer 1
Timer 2
1
Filter
ON
15
on off
15
Remove filter by pulling straight
up and out from appliance.
WARNING
CARE OF YOUR ENERGYSAVER
Page 24
Rinnai Australia 22 Energysaver - Operation & Installation Manual
Trouble Shooting Check List
If you are unsure about the way the unit is operating, contact Rinnai or your Agent.
Please check this list before asking for Service.
Fault
Cause
No Operation Lamp
Burner doesn’t ignite
Unusual Combustion
Combustion stops
Smell of Gas
Noisy Ignition
Takes too long to warm the room
Remote control does not work
Remedy
Not plugged in Plug in power cord and press
the control panel ON / OFF
button.
Power Cut Re-ignite manually after power
is restored.
(Initial Installation)
Air in gas pipe
Purge air (Installer).
Gas Filter Blocked Service Call
(Contact Rinnai).
Mis-Ignition Check customer instructions.
Flue Terminal
obstructed
Clear obstruction.
Flue manifold not
connected
Service Call
(Contact Rinnai).
Louvre obstructed Clear obstruction.
Air Filter Blocked Clean filter (weekly).
Gas Escape Service Call
(Contact Rinnai).
“ON” Timer is set Cancel “ON” Timer.
Gas turned OFF at
meter
Turn Gas “ON”.
Function / Child
Lock Set
Cancel Function / Child lock.
Battery Flat
(remote control)
Replace Battery.
TROUBLE SHOOTING
Page 25
Rinnai Australia 23 Energysaver - Operation & Installation Manual
Before asking for a service call please check the following.
These symptoms are part of the normal operation of the unit and do not indicate a fault.
Symptom Explanation
At Ignition:
Warm air does not start when the burner
lights.
The fan is started automatically after a short
delay. This is to allow the heat exchanger to
warm up, helping to avoid cold draughts.
Smoke or strange smells are produced on the
first trial light up after installation.
This is caused by grease or oil on the heat
exchanger and dust, and will stop after a short
time.
Sharp clicking noises at ignition, or when the
unit cuts down on the thermostat, or goes out.
This is simply expansion noise from the heat
exchanger.
During combustion:
Clunking noise when the thermostat operates. This is the sound of the solenoid gas valves
opening and closing.
Unit is not heating room Is the air filter blocked?
Is the set temperature high enough?
Is the warm air outlet blocked by anything?
Are the doors and windows of the room closed?
Air filter is blocked or the louvres are blocked
or obstructed
Allow heater to cool, clean air filter, operate
again.
Heater will not re-ignite after overheating Even after unit has cooled down the heater does
not ignite again. Repair is necessary. Contact
your local agent or Rinnai for a Service Call.
When the unit is turned Off:
Convection fan continues to run after turning
off.
This is to remove the residual heat from the heat
exchanger. The fan will stop when the unit cools
down.
Other points:
Steam is discharged from the flue terminal. High efficiency appliances tend to discharge
water vapour on cold days. This is normal.
Heater does not start even when ON button is
pushed and thermostat is on HIGH.
Check timer. Timer must be in the “OFF” position
for manual operation.
Unit cuts off without apparent reason Check whether filters are blocked, dirty filters will
cause the heater to overheat.
Power Failure Switch OFF, then ON again when power is
restored to re-set controls.
Timers:
Timers do not operate at set time. Timers may either be inactivated or incorrectly
programmed. Repeat programming. Refer to
“SETTING THE CLOCK” on page 18.
Timer operates for 30 seconds then cuts out. Room temperature may be higher than set
temperature. Adjust temperature upwards if
desired.
TROUBLE SHOOTING
Page 26
Rinnai Australia 24 Energysaver® - Operation & Installation Manual
The Energysaver® Range of heaters has the ability to check its own operation continuously. If a fault
occurs, an Error Message will flash on the Digital Display on the control panel. This assists with
diagnosing the fault, and may enable you to overcome a problem without a service call. Please quote
the code displayed when inquiring about service.
Set Room
on
off
Filter
Clock
Timer 1
Timer 2
Child Lock Economy Timer 1 Timer 2 Override
Set Times
ON / OFF
AM
PM
ON
Temp
Time
3
Error Code
Number will flash
1
15
Function Lock
Room
AM
PM
Timer 2
Override
Economy
Set
Tem p
Time
Timer 1
Set Times
ON / OFF
Clock
Timer 1
Timer 2
1
Filter
ON
15
on off
3
Probable Cause Comments
Power failure Turn Heater OFF the ON again
Ignition failure
Check gas supply is turned on
Turn Heater OFF the ON again
Service call if repeated
Flame failure
Check gas is turned ON.
Service call if repeated.
Overheat
Clean filter
Service call if repeated.
Room Overheat Lower room temperature to less than 40° C
Flame failure
Check gas is turned ON.
Service call if repeated.
Overheat
Clean filter
Service call if repeated.
Room Overheat Lower room temperature to less than 40° C
Sparker Failure Service call
Combustion Fan Failure Service call
Faulty ON/OFF Switch Service call
Faulty solenoids Service call
Fault Flame Rod Service call
Communication error Turn Heater OFF the ON again
Power Failure Turn Heater OFF the ON again
Sparker failure Service call
Combustion fan failure Service call
Faulty ON/OFF Switch Service call
Faulty solenoids Service call
Faulty Flame Rod Service call
Communication error Turn Heater OFF the ON again
Power failure Turn Heater OFF the ON again
Service call Room temperature sensor faulty
Room Temperature
Sensor Faulty
Service call
Overheat Temperature
Sensor Faulty
Service call
Overheat temperature sensor faulty Service call
Error Code
ERROR MESSAGES
Page 27
Rinnai Australia 25 Energysaver® - Operation & Installation Manual
RHFE-556FTR
When a safety device is activated, the cause will be indicated by a flashing display. (Filter indicator will
also flash in the case of overheat).
In all cases, you may be ab le to clear the Error Message simply by turning the heater OFF, then ON
again. If the Error Message still remains or returns on the next operation, contact Rinnai or your
nearest service agent and arrange for a service call.
Error Code Probable Cause Comments
Power failure When power failure is sensed
operation stops
Miss Ignition Flame current does not reach
1.0µA within the given time, after
solenoid valve opens
Flame Failure Flame rod current remains below
0.1µA for 3 seconds during initial
combustion
Over heat safety device High-limit temperature thermistor
or thermal fuse has activated
Over temperature cut off Room temperature is sensed as
being above 40°C for longer than
10 minutes
Room temperature thermistor
disconnection
Room temperature thermistor
open circuit
Room temperature thermistor short
circuit
Room temperature thermistor wire
trapped, touching bare metal
High-limit thermistor disconnection High limit thermistor open circuit
Service calls for general cleaning, maintenance and wear and tear are not necessarily
covered under the warranty. Service calls of this nature may be chargeable.
Faults caused by insufficient gas supply, gas quality, installation errors or operation
errors are not covered by the Rinnai warranty. Refer to seperate Warranty booklet for
details.
1
NOTE
ERROR MESSAGES
Page 28
Rinnai 26 Energysaver® - Operation & Installation Manual
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
LOCATION .............................. ................................................ .................................................... 31
GAS SUPPLY ............................................................................................................................. 31
PURGING THE GAS SUPPLY ................................................................................................... 31
ELECTRICAL SUPPLY ............................................................................................................... 31
HEATER LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
FLUE INSTALLATION CONFIGURATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
FLUE TERMINAL LOCATION .................................................................................................... 33
FLUE POSITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
WALL PENETRATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
INSTALLATION CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
HEATER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
TESTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
CHECKLIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
INSTALLATION AND COMMISSIONING CHECKLIST ........................ ... .... ... ... ... .... ... ... ... ... .... 45
CHECKLIST ON YOUR ENERGYSAVER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
INSTALLATION MANUAL - TABLE OF CONTENTS
Page 29
Rinnai Australia 27 Energysaver® - Operation & Installation Manual
Models: RHFE-556FTR
RHFE-556FDT
RHFE-557FTR RHFE-1004FTR
RHFE-1004FDT
Type of Appliance Energysaver® Fan Forced Power Flued Gas S pace
Heater
Height (mm)
- Width
- Depth
- Height
750
250
554
750
250
554
930
330
670
Weight (Kg) 22 22 42
Input (MJ/hr) - Nat
Gas
- High
- Low
23
9
23
9
37
11
Gas Control Rinnai Electronic Modulating Control
Burner Stainless Steel Ribbon Type
Gas Inlet R 1/2” Male Thread (15 mm)
TPP (kPa) - NG
- High
- Low
0.51
0.09
0.51
0.09
0.76
0.49
TPP (kPa) - LPG
- High
- Low
1.06
0.18
1.06
0.18
2.33
1.07
Flue Forced Flue
Flue Connection Supplied with heater
Flue Systems All flue systems are sold separately to suit
individual applications
Ignition Continuous electrical spark, direct to main burner
Electrical Supply 240 V, 50 Hz - The unit is fitted with a supply lead
and 3 pin plug, replace only with Rinnai part only.
Fan Centrifugal 7 Speed Fan
Rinnai are continually updating and improving products, therefore specifications are subject to
change without prior notice.
SPECIFICATIONS
Page 30
Rinnai Australia 28 Energysaver® - Operation & Installation Manual
RHFE-556FTR
RHFE-556FDT
Refer to Wall Penetration for Flue location on page 34
Air Filter Clearance
FM/FDT version only
1.
DIMENSIONS
Page 31
Rinnai Australia 29 Energysaver® - Operation & Installation Manual
RHFE-557FTR
Refer to Wall Penetration for Flue location on page 34.
For all Flueing instructions refer to seperate Co-Axial Flue Installation
Instructions supplied with the Flueing Components
DIMENSIONS
Page 32
Rinnai Australia 30 Energysaver® - Operation & Installation Manual
RHFE-1004FTR / RHFE-1004FDT
Refer to Wall Penetration for Flue location on page 34. For all Flueing
instructions refer to seperate Co-Axial Flue Installation Instructions supplied
with the Flueing Components
DIMENSIONS
Page 33
Rinnai Australia 31 Energysaver® - Operation & Installation Manual
LOCATION
When positioning the heater t he main variables governing the location are Flueing and Warm Air
Distribution.
This heater must not be installed where curtains or other combustible materials could come into
contact with it. In some cases curtains may need restraining. Refer to page 2 for additional safety
consideration.
GAS SUPPLY
The gas supply terminates outside the heater at the rear of the appliance.
Locate the gas supply pipe to suit position as per the h eater gas inlet. Refer to the drawings on page36
for appliance gas inlet location.
Gap required between the wall and heater body is 85 mm to 200 mm depending on Back Cover set
used.
PURGING THE GAS SUPPLY
All foreign materials such as filings must be purged from the gas supply, as they may cause the gas
control valve to malfunction.
ELECTRICAL SUPPLY
This heater has a power cord with a three pin plug supplied. The cord passes out of the rear of the
appliance and can extend to the left or right of the appliance.
A dedicated 240 V earthed 10 Amp power point must be used with this appliance. The power point
must to the left or the right side, it must not be above the heater. Alternatively the appliance can be
direct wired if the power supply is to be concealed.
For all installations, ONLY Rinnai Energysaver® Flue components MUST be
used. The Rinnai Energysaver
®
MUST NOT be flued into ‘natural draft’ flue
system or via a chimney.
Consult the Rinnai ‘Energysaver
®
Space Heater Co-Axial flue System
installation’ manual included with the ‘On Wall’ or ‘Direct’ flue kits for
detailed flue installation instructions.
Gas pipe sizing must consider the gas input to this appliance as well as all other
gas appliances in the premises. The gas meter and regulator must be specified for
the total gas rate. Suitable sizing chart such as the one in AS/NZS 5601 should be
used.
Consult a qualified electrician if direct wiring is required as it must comply with the
requirements of AS/NZS 5601 and AS/NZS 3000 and any other relevant local
regulations.
WARNING
WARNING
IMPORTANT
HEATER LOCATION
Page 34
Rinnai Australia 32 Energysaver® - Operation & Installation Manual
.
Consult the ‘Energysaver® Space Heater Co-Axial Flue Systems Installa tion Manual’
included with the ‘On Wall’ or ‘Direct’ flue kits for detailed flue installation
instructions. Use only Rinnai Flue components with this appliance.
The following configurations are currently available. For alternative configurations contact Rinnai
Components
DIRECT / EXTENDED
Option A (Direct) Option B (Direct Extended)
Direct Flue Kit ESDFK Direct Flue Kit
Co-Ax Pipe 900mm
(Optional) #
ESDFK
ESPIPE900
SIDEWAYS Components
Direct Flue Kit
Co-Ax Pipe 900mm #
Back Cover Set
(see note below)
ESDFK
ESPIPE900
EXTERNAL WALL Components
Option A (Vertical Termination) Option B (On Wall Termination)
Direct Flue Kit
Co-Ax Pipe 900mm #
Bend (2 x 45º)
Condensate Trap
Roof Cowl
ESDFK
ESPIPE900
ESBEND
ESCONDK
ESROOFCOWL
Direct Flue Kit
Co-Ax Pipe 900mm #
Bend (2 x 45º)
Condensate Trap
ESDFK
ESPIPE900
ESBEND
ESCONDK
IN-WALL Components
Option A (Direct) Option B (Offset)
Vertical Adaptor Kit §
Co-Ax Pipe 900mm #
Roof Cowl
ESFKITIW
ESPIPE900
ESROOFCOWL
Vertical Adaptor Kit §
Co-Ax Pipe 900mm #
Bend (2 x 45º)
Roof Cowl
ESFKITIW
ESPIPE900
ESBEND
ESROOFCOWL
UNDER FLOOR Components
Direct Flue Kit
Co-Ax Pipe 900mm #
Bend (2 x 45º)
Back Cover Set
(see note below)
ESDFK
ESPIPE900
ESBEND
# Order lengths as required § Includes Condensate Trap (ESCONDK)
The Energysaver Heater comes supplied with a standard back cover set. For
‘Sideways’ & ‘Underfloor’ installations, refer to the ‘Energysaver Space Heater CoAxial Flue System Installation Manual’ for the alternative back cover set required.
Flue is NOT to be terminated under the floor or in a roof space.
‘Down & Out’ and vertical ‘through roof’ flue installations are permit ted ONLY when
the flue terminal is located externally.
For horizontal installations there must be a continuous fall of at least 2° to the
termination point to drain condensate.
All terminations exceeding a vertical height of 1.5 metres must incorporate a
condensate trap.
‘Down & Out’ Flue systems must have a continuous fall of at least 2° to the
termination point to drain condensate. Flue terminal must be at le ast 300 mm above
the ground in accordance with AS/NZS 5601-Fig. 6.2.
AT NO TIME MUST THE ‘AIR INTAKE’ HOSE BUT CUT OR SHORTENED. For more
detailed information refer to ‘Energysaver
®
Space Heater Co-Axial Flue Systems
Installation Manual’
NOTE
NOTE
DO NOT
WARNING
FLUE INSTALLATION CONFIGURATIONS
Page 35
Rinnai Australia 33 Energysaver® - Operation & Installation Manual
FLUE TERMINAL LOCATION
The flue terminal should be positioned away from
flammable materials.
Ensure that the location of the flue terminal can comply
with the requirements of AS/NZS 5601 Clause 6 and Fig. 6.2
which is reproduced below.
* AS/NZS 5601 was current at the time of printing this manual, but may have
been superseded. It is the installers responsibility to ensure that the current
version of this standard is used.
WARNING
Flue terminal Fan assisted flue appliance only Gas meter Electricity meter or fuse box Mechanical air inlet
Natural draft Fan assisted
• Appliances up to 50 MJ/h input 300 200
• Appliances over 50 MJ/h input 500 300
b From the ground, above a balcony or other surface * 300 300
c Front a return wall or external corner * 500 300
d
From a gas meter (M) (see 5.11.5.9 for vent terminal location of regulator )
(see Table 6.6 for New Zealand requirements) 1000 1000
e From an electricity meter or fuse box (P) † 500 500
f From a drain pipe or soil pipe 150 75
g Horizontally from any building structure* = or obstruction facing a terminal 500 500
h From any other flue terminal , cowl, or combustion air intake † 500 300
• Appliances up to 150 MJ/h input * 500 300
• Appliances over 150 MJ/h input up to 200 MJ/h input * 1500 300
• Appliances over 200 MJ/h input up to 250 MJ/h input * 1500 500
• Appliances over 250 MJ/h input * 1500 1500
• All fan-assisted flue appliances , in the direction of discharge - 1500
k From a mechanical air inlet, including a spa blower 1500 1000
• Space heaters up to 50 MJ/hr input 150 150
• Other appliances up to 50 MJ/hr input 500 500
• Appliances over 50 MJ/h input and up to 150 MJ/h input 1000 1000
• Appliances over 150 MJ/h input 1500 1500
1
Where dimensions c, j or k cannot be achieved an equivalent horizontal distance
measured diagonally from the nearest discharge point of the terminal to the opening
may be deemed by the Technical Regulator to comply.
2
See Clause 6.9.4 for restrictions on a flue terminal under a covered area.
3
See Figure J3 for clearances required from a flue terminal to an LP Gas cylinder.
A flue terminal is considered to be a source of ignition.
4
Ref. Item
a
Min. clearances (mm)
Below eaves, balconies and other projections:
j
Horizontally from an openable window, door, non-mechanical air inlet, or any other opening into a building
with the exception of sub-floor ventilation:
Vertically below an openable window, non-mechanical air inlet, or any other opening into a building with the
exception of sub-floor ventilation:
NOTES:
† - Prohibited area below electricity meter or fuse box extends to ground level.
FIGURE 6.2 (in-part) MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS, FAN-ASSISTED FLUE
TERMINALS, ROOM-SEALED APPLIANCE TERMINALS AND OPENINGS OF OUTDOOR APPLIANCES
* - unless appliance is certified for closer installation
For appliances not addressed above acceptance should be obtained from the Technical Regulator.
n
NOTE
FLUE POSITIONING
Page 36
Rinnai Australia 34 Energysaver® - Operation & Installation Manual
Below are diagrams and associat ed dimension tables for wall penetrations for each Energysaver
heater models.
RHFE 556
RHFE 557 RHFE 1004
All dimension are in millimetres RHFE 556 RHFE 557 RHFE 1004
i
Width of appliance 750 550 930
ii
Centre-Line of appliance 375 275 465
iii
Arc axis (Axis point of the flue elbow) ———
A
Horizontal distance from Centre-Line to arc centre 220 172 305
B
Vertical distance from base to arc centre 215 264 165
C
Minimum horizontal limit of arc 240 200 325
D
Minimum vertical limit of arc 215 264 250
E
Maximum vertical limit of arc 310 390 340
F
Maximum horizontal limit of arc 300 230 365
G
Penetration diameter 100 100 100
D
B
E
A
C
F
G
ii
I
iii
D
B
E
A
C
F
G
ii
i
iii
D
B
E
A
F
C
G
ii
i
iii
WALL PENETRATIONS
Page 37
Rinnai Australia 35 Energysaver® - Operation & Installation Manual
When cutting the flue transition
for joining to other components
the minimum total length is not
to be less than 300mm!
When cutting the flue transition
for joining to other components
the minimum total length is not
to be less than 300mm!
• DIRECT EXTENDED
• EXTERNA L WALL
• IN-WALL
• DIRECT EXTENDED
• UNDER FLOOR
•SIDEWAYS
SIDEWAYS
IN-WALL
EXTERNAL
WALL
DIRECT
EXTENDED
UNDER FLOOR
When cutting the flue transition
for joining to other components
the minimum total length is not
to be less than 300mm!
DIRECT
•DIRECT
INSTALLATION CONFIGURATION
Page 38
Rinnai Australia 36 Energysaver® - Operation & Installation Manual
1. UNPACKING THE APPLIANCE
The heater is supplied in one carton containing; Heater, Standard Rear Cover Set and Bolt Pack.
Remove all packaging materials. Check for damage. If any damage is evident DO NOT install or
operate this appliance. Contact your supplier for advice. Before installing the heater, check it is
labelled for the correct gas type, (refer to the data label at the rear of the heater). Refer to the local
gas authority for confirmation of gas type if you are in doubt.
The heater does not come supplied with flue components. These are
purchased separately.
ONLY Rinnai Energysaver
®
Co-Axial Flue System Flue components can be
used with this appliance.
240 VOLTS, RISK OF ELECTRICAL SHOCK!
Ensure the appliance is disconnected from mains power.
2. CONNECTING THE APPLIANCE TO THE CONSUMER GAS PIPE
1. Remove the plastic protection cap from the threaded gas inlet located at the rear of the appliance.
2. Position the appliance gas inlet in line with gas supply from wall.
3. Attach gas supply pipe to the appliance gas inlet and tighten - finger tight. Appliance has R1/2
fitting.
4. On the wall behind the appliance, at a level of about midway of the heaters height, ma rk the vertical
centre line of the heater.
5. Mark the flue penetration position in accordance with ‘Energysaver
®
Space Heater Co-Axial Flue
System Installation’ manual.
6. Undo the gas connection, remove the heater.
7. Cut Flue penetration(s)
8. Mark out the securing bracket screw holes in
accordance with the drawing adjacent and table
below using the centre line as reference.
9. Attach the two securing brackets supplied to the wall
using the two 8g x 30mm screws supplied, or suitable
equivalent.
10.Install flue system in accordance with ‘Energysaver
®
Space Heater Co-Axial Flue System
Installation manual’.
11.Return the heater to the final position.
NOTE
WARNING
A
B
C
L
Floor Level
Heater Centre Line
Securing brackets
Models A = Width B = Height
RHFE-556FTR 450 506
RHFE-556FDT 450 506
RHFE-557FTR 300 685
RHFE-1004FTR 500 622
RHFE-1004FDT 500 622
SECURING
BRACKET
HEATER INSTALLATION
Page 39
Rinnai Australia 37 Energysaver® - Operation & Installation Manual
12.Connect flue in accordance with ‘Energysaver
®
Space Heater, Co-Axial Flue System Installation
Manual’.
13.Connect gas supply line and fully tighten connection.
Use a soapy solution to test all gas connections. If a leak is present bubbles will
form at the leak point. When finished remove any residue with a rag. Prevent any
soapy solution from coming in contact with electrical components.
14.Fit left and right cover panels to the rear of the appliance by clipping the panels onto the location
tabs then fastening into position using the two 6g x 8mm pan head screws supplied. Screws locate
into pre-drilled and formed recesses at the bottom edge of the panels
15.Remove the Fan Filter and carefully fit the top cover panel ensuring the rear fold locates neatly
between the two securing brackets and wall.
16.Secure the top cover panel with two 6g x 8mm pan head screws supplied or suitable equivalent.
17.Replace the Fan Filter.
Air hose and heater exhaust connections at the Energysaver® heater MUST
be made and check in accordance with these instructions. Improper
connections may result in dangerous situations, for example, the dispersion
of combustion products in the space being heated.
CAUTION
CAUTION
HEATER INSTALLATION
Page 40
Rinnai Australia 38 Energysaver - Operation & Installation Manual
• Purge air and swarf from gas line. Connect gas. Connection can easily be reached from the right
hand side rear of the appliance.
• Remove bottom trim (pulls off). Remove louvres and front panel (7 screws).
PRESSURE CHECKING PROCEDURE
1. Check that SW6 (Dip switches) are correct for the gas type for which the appliance is to be used.
(Refer to diagram opposite).
2. There are two test points, one the heat exchanger, one on the gas manifold. Connect a pressure
gauge between both test points. (Connect one side of the gauge to one point, the other side of
the gauge to the other). If you are using an electronic manometer, connect the side to the heat
exchanger test point.
3. Press the ON/OFF button to operate the appliance.
4. With the appliance operating, press SW5 once.
5. Press SW4 to operate the appliance on forced low.
6. Check the pressure against the low pressure shown on the data plate. (Right hand side panel).
7. Press SW4 again.
8. Pre ss SW3 to operate the appliance on forced high.
9. Check the pressure against the high pressure shown on the data plate.
10. Press SW3 again.
11. Press SW5 again to return the heater to normal operation.
12. Turn the heater OFF, remove the pressure gauge, and replace the test point screws.
13. Reassemble appliance, set the clock and check appliance operation.
THE REGULATOR HAS BEEN FACTORY PRE-SET. IF THE PRESSURE IS INCORRECT, CHECK THE
SUPPLY PRESSURE FIRST, BEFORE MAKING ANY ADJUSTMENT TO THE APPLIANCE.
1. Follow checking procedure 1-6, reset the low pressure by using the “ “ button or “ “ buttons
on the control panel.
2. Press SW4 again the lock in the selected setting.
3. Follow checking procedure 8 and 9, reset the high pressure by using “ “ button or “ “ buttons
on the control panel.
4. Press SW3 again to lock in the selected setting.
5. Press SW5 to return the heater to normal operation.
6. Turn the heater OFF, remove the pressure gauge, and replace the test point screws.
7. Reassemble appliance, set the clock (see page 13) and check appliance operation.
• CAUTION: 240 V INSIDE APPLIANCE
TESTING
Page 41
Rinnai Australia 39 Energysaver - Operation & Installation Manual
FITTING TOP SPACER + WALL CLIP
Replace top and right hand spacers, clipping the
top spacer into the wall brackets at the same time
as attaching it to the heater.
Secure top spacer with the screws provided.
THE HEATER IS NOW SECURED TO THE
WALL.
Tighten all screws, fit fan filter.
INSTRUCT CUSTOMER ON USE OF HEATER
When you are satisfied that the appliance is operating correctly, explain operation o f heater to the
Customer.
Fault-Failure Procedure
If unable to get the heater to operate correctly, contact Rinnai.
(Check the insulating resistance of the appliance).
Spacer
Fan Filter
Page 42
Rinnai Australia 40 Energysaver - Operation & Installation Manual
RHFE-557FTR
MARK PART NAME MARK PART NAME
MS MAIN SWITCH OH. TH OVER HEAT THERMISTOR
TH THERMISTOR OHS1~2 OVER HEAT SWITCH 1~2
TF THERMAL FUSE FM FAN MOT OR
F FUSE BL COMBUSTION FAN MOTOR
CF CONVECTION FAN SP SPARKER
FCC FAN CONTROL CIRCUIT FR FLAME ROD
ER ELECTRODE SV1~2 MAIN SOLENOID VALVE
1~2
POV MODULATING SOLENOID
VALVE
CPU CENTRAL PROCESSING
UNIT
TR TRANSFORMER RC REMOTE CONTROL
TB TERMINAL BLOCK RCR REMOTE CONTROL
RECEIVER
WIRING DIAGRAM
Page 43
Rinnai Australia 41 Energysaver® - Operation & Installation Manual
RHFE-556FTR
MARK PART NAME MARK PART NAME
MS MAIN SWITCH RCR REMOTE CONTROL
RECEIVER
RC REMOTE CONTROL TB TERMINAL BLOCK
TH THERMISTOR OH. TH OVER HEAT THERMISTOR
TF THERMAL FUSE OHS1~3 OVER HEAT SWITCH 1~3
FFUSEFMFAN MOTOR
CF CONVECTION FAN BL COMBUSTION FAN MOTOR
FCC FAN CONTROL CIRCUIT SP SPARKER
ER ELECTRODE FR FLAME ROD
POV MODULATING SOLENOID
VALVE
SV1~2 MAIN SOLENOID VALVE 1~2
TR TRANSFORMER CPU CENTRAL PROCESSING UNIT
WIRING DIAGRAM
Page 44
Rinnai Australia 42 Energysaver® - Operation & Installation Manual
RHFE-556FDT
MARK PART NAME MARK PART NAME
MS MAIN SWITCH TB TERMINAL BLOCK
TH THERMISTOR OH. TH OVER HEAT THERMISTOR
TF THERMAL FUSE OHS1~3 OVER HEAT SWITCH 1~3
FFUSEFMFAN MOTOR
CF CONVECTION FAN BL COMBUSTION FAN MOTOR
FCC FAN CONTROL CIRCUIT SP SPARKER
ER ELECTRODE FR FLAME ROD
POV MODULATING SOLENOID
VALVE
SV1~2 MAIN SOLENOID VALVE 1~2
TR TRANSFORMER CPU CENTRAL PROCESSING UNIT
WIRING DIAGRAM
Page 45
Rinnai Australia 43 Energysaver® - Operation & Installation Manual
RHFE-1004FTR
MARK PARTS NAME MARK PARTS NAME
MS MAIN SWITCH OH.TH OVER HEAT THERMISTOR
R.TH THERMISTOR OHS OVER HEAT SWITCH
TF1~3 THERMAL FUSE FM CONVECTION FAN MOTOR
F FUSE SP SPARKER
ER ELECTRODE SV1~3 MAIN SOLENOID VALVE 1~3
POV MODULATING SOLENOID VALVE BL COMBUSTION FAN MOTOR
TR TRANSFORMER FCC FAN CONTROL CIRCUIT
FR1~3 FLAME ROD 1~3 RCR REMOTE CONTROL RECEIVER
RC REMOTE CONTROLLER TB TERMINAL BLOCK
CF CONVECTION FAN CPU CENTRAL PROCESSING UNIT
WIRING DIAGRAM
Page 46
Rinnai Australia 44 Energysaver® - Operation & Installation Manual
RHFE-1004FDT
*FTR TYPE ONLY
MARK PARTS NAME MARK PARTS NAME
MS MAIN SWITCH OH.TH OVER HEAT THERMISTOR
R.TH THERMISTOR OHS OVER HEAT SWITCH
TF1~3 THERMAL FUSE FM CONVECTION FAN MOTOR
F FUSE SP SPARKER
ER ELECTRODE SV1~3 MAIN SOLENOID VALVE 1~3
POV MODULATING SOLENOID VALVE BL COMBUSTION FAN MOTOR
TR TRANSFORMER FCC FAN CONTROL CIRCUIT
FR1~3 FLAME ROD 1~3 *RCR REMOTE CONTROL RECEIVER
RC REMOTE CONTROLLER TB TERMINAL BLOCK
CF CONVECTION FAN CPU CENTRAL PROCESSING UNIT
WIRING DIAGRAM
Page 47
Rinnai Australia 45 Energysaver® - Operation & Installation Manual
CHECKLIST
INSTALLATION AND COMMISSIONING CHECKLIST
• Complete the Installation Check List and the Installer details below.
• Instruct customer on the Energysaver® operation.
• Ensure the customer understands the content of this manual.
*If you have answered NO to any of the above, you must correct be fore appliance hand-ove r to the customer.
Advise the customer that during the initial burning in period of approximately 2 hours, some
vapour and smell may be emitted from the heater. This is normal operation for a new heater.
During this period the heater should be operated on ‘High’ and the spa ce being heated should
be well ventilated.
The grill louvre and rear cover fitted to this appliance r educes the risk of fire and injury, no part
of it should be permanently removed.
Ensure the Customer understands that:
No part of this appliance should be permanently removed.
Paper or other material must not be forced into the louvres of this appliance.
Young children and the infirm should be supervised at all times while in the vicinity of this
appliance while it is in operation or able to be turned on.
Attention Installer - Have you checked?
Yes *No
1. Is the appliance positioned in a suitable location (clearances, combustible clearances mantels
and surrounds etc)?
2. Have all packaging / protective materials been removed prior to operation?
3. The Appliance Test Point (Burner) Pressure is correct for it's particular installation / flue
configuration and adjusted if necessary.
4. Have you used only Rinnai Energysaver® flueing components?
5. That the air inlet hose and flue connections are sound?
6. That the Appliance is secured to the wall as per Installation manual?
7. Gas Supply pipe is purged of foreign matter before connection?
8. That gas connections are correct?
9. Have you turned on the power?
10.Is the appliance inlet pressure correct with all other resident gas appliances operating?
11.Have you shown the customer how to operate the heater and informed them of the safety
requirements?
12.Where applicable, have you connected the condensation drain hose in accordance with the
Installation manual?
13.Have you checked the flue clearances and installation as per the Installation manual and as per
AS/NZS 5601?
14.Have you filled out the "Installation Record" found at the front of this manual?
15.Is the end-user fully aware of the servicing schedule?
16.Have you completed the "Energysaver® Commissioning Check List" attached to the front of the
Appliance?
17.Have you left this Operation and Installation manual with the customer?
CHECKLIST ON YOUR ENERGYSAVER
Page 48
Rinnai Australia 46 005-009 RHFE-556/557/1004 OIM Energysaver Issue 2 - 9/7/14
Head Office
100 Atlantic Drive,
Keysborough, Victoria 3173
P.O. Box 460
Braeside, Victoria 3195
Tel: (03) 9271 6625
Fax: (03) 9271 6622
National Help Line
Tel: 1300 555 545* Fax: 1300 555 665*
*Cost of a local call Higher from mobile or public phones.
Australia Pty. Ltd.
ABN 74 005 138 769
Internet: www.rinnai.com.au
E-mail: enquiry@rinnai.com.au
Rinnai has a Service and Spare Parts network with personnel who are fully trained
and equipped to give the best service on your Rinnai appliance. If your appliance
requires service, please call our National Help Line. Rinnai recommends that this
appliance be serviced every 2 years.
CONTACT INFORMATION
Loading...