Stick Up Cam Elite
02_Stick_Up_Cam_Elite_MANUAL.indd 1 9/12/19 1:47 PM
1. Set up your
Download from
Windows Store
Stick Up Cam Elite.
Download the Ring app.
The app walks you through setting up and managing
your Stick Up Cam Elite.
Search for “Ring” in one of the app stores below, or
visit: ring.com/app
Grab your Wi-Fi password.
You’ll need it to set up your Stick Up Cam.
Write it down below so it’s handy when you need it:
Your Wi-Fi password
02_Stick_Up_Cam_Elite_MANUAL.indd 2-3 9/12/19 1:47 PM
Let’s get your Stick Up Cam ready.
First, slide off the bottom cover.
Do not reattach this cover until setup is complete!
When you plug your Ethernet cable
into your Stick Up Cam, be sure to
feed it through the hole in this bottom
cover first.
You’ll reattach the cover to your Stick
Up Cam in a later step.
Powering your Stick Up Cam
Stick Up Cam connects using Power over Ethernet (or PoE).
This lets you use one cable for both power and internet.
Most Ethernet equipment does not provide PoE, so we’ve
included a PoE Adapter. You connect it to your network and
a power outlet, then connect it to your Stick Up Cam.
If your home is already equipped with a PoE system, you
can connect Stick Up Cam directly to a PoE-enabled
Ethernet port.
If using an existing PoE hub or switch, it must meet the IEEE 802.3af (PoE) or IEEE
802.3at (PoE\+) standard.
IN OUT
PoE Adapter
(Included)
02_Stick_Up_Cam_Elite_MANUAL.indd 4-5 9/12/19 1:47 PM
54
Security Cams
Connect your Stick Up Cam.
Use the included Ethernet cable to connect the PoE Adapter
to your internet modem or Ethernet switch. Purchase a 2nd
Ethernet cable to connect Stick Up Cam to the PoE Adapter.
Internet Modem,
Ethernet Switch, or Hub
Power Outlet
IN OUT
Set up your Stick Up
Cam in the Ring app.
In the Ring app, select
Set Up a Device.
When prompted, select
Security Cams and follow
the in-app instructions.
Try it out!
After setup, tap the Live View
button in the Ring app to
see live video from your Stick
Up Cam.
P
oE Adapter
Blue light flashing?
If the light on the front of your Stick Up Cam is flashing after
For outdoor use, install your PoE Adapter indoors, then run an Ethernet cable outdoors
to your Stick Up Cam.
6
02_Stick_Up_Cam_Elite_MANUAL.indd 6-7 9/12/19 1:47 PM
setup, it’s updating its software.
Do not unplug your Stick Up Cam while the light is flashing!
2. Install your
Stick Up Cam Elite.
How to use Stick Up Cam
on a table or shelf:
Choose a location.
Stick Up Cam is happy just about anywhere, indoors or out.
It comes ready to sit on a flat surface like a table or shelf, but
can also be mounted to a wall or ceiling.
Choose a spot where it can provide the view you want,
within reach of the Ethernet port you’ve connected to the
included Ring PoE Adapter.
Table or shelf Mounted on a wall Mounted on a ceiling
Make sure that your Ethernet
cable has been routed
through the hole in the
bottom cover.
Then, slide the cover into
place on your Stick Up
Cam. Secure the cover with
the attached screw, using
the star-shaped end of the
screwdriver bit.
Finally, place Stick Up Cam in
your chosen position. Your
Stick Up Cam is now ready to
use.
98
02_Stick_Up_Cam_Elite_MANUAL.indd 8-9 9/12/19 1:47 PM
How to install Stick Up Cam
on a wall:
Remove the plastic cover and
rubber pad from the base.
You’ll put the cover back on once
you’ve mounted your
Stick Up Cam.
Flip the base to the rear.
The base of the stand is hinged. Before wall-mounting, flip
the base down and behind your Stick Up Cam.
Push the rubber pad
back into the base.
The rubber pad should sit
between your wall and the
base of your Stick Up Cam.
Drive the screws.
Hold the round part of the base against your wall, rubberside down. Use the integrated level to ensure it’s straight.
Finally, mount it with the included screws.
Then, head to page 14 for the final steps.
1110
02_Stick_Up_Cam_Elite_MANUAL.indd 10-11 9/12/19 1:47 PM
How to install Stick Up Cam
on a ceiling:
Remove the plastic cover
from the base.
You’ll put the cover back on once
you’ve mounted your
Stick Up Cam.
Rotate the stand above the camera:
The whole stand can rotate on its axis. Before ceilingmounting, rotate the stand 180 degrees so the base is
positioned above your Stick Up Cam.
Drive the screws.
Hold the round part of the base against your ceiling,
rubber-side down. Then mount it with the included screws.
Then, head to page 14 for the final steps.
1312
02_Stick_Up_Cam_Elite_MANUAL.indd 12-13 9/12/19 1:47 PM
Final steps for wall or
ceiling mounting:
Close it up.
Make sure that your Ethernet cable has been routed through
the hole in the bottom cover and is plugged into your Stick
Up Cam.
Then, slide the cover back into place and secure it with the
attached screw, using the star-shaped end of the included
screwdriver bit.
Snap the cover back onto the base.
Then, secure it with the included security screw, using the
star-shaped end of the included screwdriver bit.
Now your Stick Up Cam is installed and ready to use.
1514
02_Stick_Up_Cam_Elite_MANUAL.indd 14-15 9/12/19 1:47 PM
For additional help, visit: ring.com/help
Or give us a call…
US 1 800 656 1918
Canada 1 855 300 7289
Worldwide +1 310 929 7085
For a list of all our customer support numbers, visit:
ring.com/callus
To review your warranty coverage, please visit www.ring.com/warranty.
© 2019 Ring LLC or its affiliates. Ring and all related logos are trademarks of Ring LLC or its affiliates.
Last updated: 09/12/19
02_Stick_Up_Cam_Elite_MANUAL.indd 16 9/12/19 1:47 PM
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
This device is restricted to indoor use.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.
Loading...