155mm
140mm
Stick Up Cam Wired
2520AH710L-B01FX2520AH710L-B01FX2520AH710L-B01FX2520AH710L-B01FX2520AH710L-B01FX2520AH710L-B01FX2520AH710L-B01FX2520AH710L-B01FX
Stick_Up_Cam_Wired_MANUAL.indd 1 7/30/18 6:21 PM
1. Set up your
Download from
Windows Store
Stick Up Cam Wired
in the Ring app.
Download the Ring app.
The app walks you through setting up and managing
your Stick Up Cam Wired.
Search for “Ring” in one of the app stores below, or
visit: ring.com/app
Grab your Wi-Fi password.
You’ll need it to set up your Stick Up Cam.
Write it down below so it’s handy when you need it:
Your Wi-Fi password
32
Stick_Up_Cam_Wired_MANUAL.indd 2-3 7/30/18 6:21 PM
Plug in your
Spotlight Cam Wired
Spotlight Cam Battery
Stick Up Cam Elite
Stick Up Cam Battery
Stick Up Cam.
Begin the setup process in
the same room as your Wi-Fi
router. You can move it to its
intended position later.
First, slide off the bottom cover.
Set up your Stick Up
Cam in the Ring app.
In the Ring app, select Set
Up a Device.
When prompted, select Stick
Up Cam Wired and follow
the in-app instructions.
Then, plug your Stick Up Cam
into a power outlet using the included USB cable and power
supply.
If you’ll be connecting Stick Up Cam using
Power Over Ethernet, then use an ethernet
cable to connect it to a PoE port.
Try it out!
After setup, tap the Live View
button in the Ring app to
see live video from your Stick
Up Cam.
Blue light flashing?
If the light on the front of your Stick Up Cam Wired flashes
after setup, it may be updating its software.
When the flashing stops, Stick Up Cam is ready to use.
54
Stick_Up_Cam_Wired_MANUAL.indd 4-5 7/30/18 6:21 PM
2. Install your
Stick Up Cam Wired.
Choose a location.
Stick Up Cam Wired is happy just about anywhere, indoors
or out. It can sit on its own stand, or mount to a wall or
ceiling.
Choose a spot where it can provide the view you want,
within reach of a power outlet or an Ethernet port with PoE.
Installing on a shelf or table?
Simply attach the base cover to the top of the base, and
push the rubber pad into the bottom of the base.
That’s it! You can skip to the next section.
76
Stick_Up_Cam_Wired_MANUAL.indd 6-7 7/30/18 6:21 PM
Mounting on a wall?
Mounting on a ceiling?
Push the rubber pad
into the top of the
Flip the base toward
the rear.
base.
Drive the screws.
Hold the circular part of the base against
your wall, rubber-side down. Use the
integrated level to ensure it’s straight.
Then, mount it with the included screws.
Finally, snap the cover onto the base
and install the security screw.
Swivel the base
above the camera.
Push the rubber pad
into the base.
Drive the screws.
Hold the circular part of the base
against your ceiling, rubber-side down.
Then, mount it with the
included screws.
Finally, snap the cover onto the base
and install the security screw.
98
Stick_Up_Cam_Wired_MANUAL.indd 8-9 7/30/18 6:21 PM
You’re almost done!
Now, just plug your Stick
Up Cam back in at its final
installed location, and it’ll be
ready to protect you.
3. Need a little setup help?
If using USB: Plug the included
USB power supply and cable
into an outlet. Feed the other
end through the bottom cover
of your Stick Up Cam and plug
it in.
If using Ethernet: Plug an
Ethernet cable into a Power
over Ethernet (PoE) port. Feed
the other end through the
bottom cover of your Stick
Up Cam and plug it in. If your
Ethernet port does not provide
PoE, connect both Ethernet
and the USB power supply.
Then, slide the bottom cover back into place over the cable
connections and use the star-shaped screwdriver bit to
tighten the security screw.
Once your Stick Up Cam powers up, it reconnects to the
internet automatically.
If your in-app setup doesn’t
go as planned, try these tips:
Get your Wi-Fi password
just right.
The most common setup
issues come from entering
the wrong Wi-Fi password.
These passwords are casesensitive, and every little
error counts.
Reboot your router.
If you entered the right
password but you’re having
no luck, try turning your Wi-FI
router off, wait 30 seconds,
then turn it back on.
Then, begin setup again in
the Ring app.
Need additional help?
If the problem you’re having
isn’t addressed here, and
you need further help, scan
the code below with the
camera app on your iPhone
or a QR code scanning app
on your Android device.
1110
Stick_Up_Cam_Wired_MANUAL.indd 10-11 7/30/18 6:21 PM
For additional help, visit: ring.com/help
Or give us a call…
US 1 800 656 1918
Canada 1 855 300 7289
Worldwide +1 310 929 7085
For a list of all our customer support numbers, visit:
ring.com/callus
To review your warranty coverage, please visit www.ring.com/warranty.
Patents: www.ring.com/patents
© 2018 Ring LLC or its affiliates.
RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates.
Last updated: 07/30/18
12
2520AH710L-B01FX
Stick_Up_Cam_Wired_MANUAL.indd 12 7/30/18 6:21 PM
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifi cations not expressly a pproved by the party respon sible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subj ect to the following t wo con ditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm betwee n the radiator & your body.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of
the device.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm b etween the
radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de
rayonnement et votre corps
CAN ICES-3 (B)/NMB-3(B)
Loading...