Ring BHARC011 User Manual

150mm

100mm

Spotlight_Cam_Wired_2_MANUAL.indd 1 6/19/19 2:39 PM

Spotlight Cam Wired

1. Set up your

Download from

Windows Store

Spotlight

Download the Ring app

The Ring app will walk you
through setting up and
managing your Spotlight Cam.

Cam in the
Ring app.

Search for “Ring” in one of the
app stores below, or visit:

ring.com/app.

Grab your Wi-Fi password

It’s required for the in-app setup. Write
it down below so it’s handy when you
need it:

Your Wi-Fi password

32

Spotlight_Cam_Wired_2_MANUAL.indd 2-3 6/19/19 2:39 PM

Plug your Spotlight Cam

Spotlight Cam Wired

Spotlight Cam Battery

into a power outlet

Set up your Spotlight Cam
in the Ring app

Plug your Spotlight Cam into an outlet
in the same room as your Wi-Fi router
to set it up.

In the Ring app, select Set Up Device
and follow the in-app instructions.

54

Spotlight_Cam_Wired_2_MANUAL.indd 4-5 6/19/19 2:39 PM

Try it out!

White light flashing?

After setup, select the Live View button
to see video from the camera in the
Ring app.

If the light on the bottom of your
Spotlight Cam is flashing after setup,
it’s updating its internal software.

The light will stop flashing when the
update is completed. This update can
take up to a few minutes.

76

Spotlight_Cam_Wired_2_MANUAL.indd 6-7 6/19/19 2:39 PM

Test video quality outside

Now, unplug your Spotlight Cam and
take it outside to where you want to
install it. Plug Spotlight Cam into an
outdoor outlet and test video quality
again.

2. Install your
Spotlight Cam
on the wall.

98

Spotlight_Cam_Wired_2_MANUAL.indd 8-9 6/19/19 2:39 PM

Before you begin

This is everything you’ll need to install
your Spotlight Cam.

Screwdriver

Use the screwdriver handle to
hold the provided bit.

Phillips Bit

Use the Phillips bit for installing
the mounting bracket and
tightening the security screw.

Drill Bit

Use this to pre-drill holes if
installing on a masonry surface,
such as stucco or brick.

Mounting Bracket

Attach this to the wall first,
then slot Spotlight Cam into
the mounting bracket. It also
features a built-in level.

Install Screws (5)

Use these to install the mounting
bracket on your wall.

Wall Anchors (16)

Use these to attach the mounting
bracket and the cable clips to your
wall, if installing on a masonry surface,
such as stucco or brick.

Cable Clips (11)

Use these to attach the power cable
to your wall.

1110

Spotlight_Cam_Wired_2_MANUAL.indd 11 6/19/19 2:39 PM

How it all fits together

Setup
Button

Install
Screws

Security
Screw

Mounting
Bracket

Wire
Clip

Lights

Motion
Detector

1312

Spotlight_Cam_Wired_2_MANUAL.indd 13 6/19/19 2:39 PM

Select an install height

When mounted at 9 feet off the
ground, with the motion detector
parallel to the ground, the motion
sensor is optimized to detect human­sized objects at up to 30 feet.

Parallel to ground

9 feet

(3 Meters)

30 feet (10 Meters)

Spotlight_Cam_Wired_2_MANUAL.indd 14-15 6/19/19 2:39 PM

Install the mounting
bracket

Use the built-in level to make sure
your Spotlight Cam will be level before
marking your holes.

If installing on a masonry surface,
first drill holes using the provided
drill bit. Insert the wall anchors before
installing the screws.

If installing on a wood surface, use the
install screws to screw the mounting
bracket directly into your wall.

1716

Spotlight_Cam_Wired_2_MANUAL.indd 16-17 6/19/19 2:39 PM

Attach the base of Spotlight
Cam to the mounting
bracket

Slot the base down to lock it to the
mounting bracket.

1918

Spotlight_Cam_Wired_2_MANUAL.indd 19 6/19/19 2:39 PM

Tighten the security screw

Using the Phillips end of the
screwdriver bit, tighten the security
screw on the right until your Spotlight
Cam is secure.

2120

Spotlight_Cam_Wired_2_MANUAL.indd 21 6/19/19 2:39 PM

Secure the cable

Use the provided cable clips to secure
the cable on your wall.

Use the included drill bit to pre­drill holes in the wall and insert the
provided anchors first if installing on a
masonry surface, like stucco or brick.

The power cable can be
painted to match the wall.

2322

Spotlight_Cam_Wired_2_MANUAL.indd 23 6/19/19 2:39 PM

Plug Spotlight Cam in

If Spotlight Cam is not already
plugged into a power outlet, plug it in
now.

If you’ve already completed the in­app setup, wait about a minute for
Spotlight Cam to power up and come
back online.

2524

Spotlight_Cam_Wired_2_MANUAL.indd 24-25 6/19/19 2:39 PM

Adjust the camera angle

To ensure accurate motion detection,
position the camera with the motion
detector parallel to the ground.

Tighten the side screw on the left to
secure the camera position.

2726

Spotlight_Cam_Wired_2_MANUAL.indd 27 6/19/19 2:39 PM

For additional help, visit:

ring.com/help

Or give us a call…

US 1 800 656 1918

UK 01727 263045

FR [phone]

DE [phone]

AU 1 300 205 983

NZ [phone]

Mexico (D.F) 52 55 8526 5445

Worldwide [phone]

For a list of all our customer support
numbers, visit: ring.com/callus

Spotlight_Cam_Wired_2_MANUAL.indd 28 6/19/19 2:39 PM

To review your wa rranty cove rage, plea se visit ww w.ring.com/warranty.

© 2019 Ring LLC or its a liates.

Ring and a ll related log os are tradem arks of Ring LLC o r its aliates .

Last updated: 06/19/19

2520A1803L-A02FX

1523 26th St.
Santa Monica, CA 90404

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.

Protect the device from direct sunlight. Install the device at dry locations and protect it against
rain and humidity. The device may not get contact to salt water or other conductive liquids. The
device must be charged only within a building in a dry state.

To review your warranty coverage, please visit www.ring.com/warranty

© 2019 Ring LLC or its affiliates

Ring and all related logos are trademarks of Ring LLC or its affiliates.

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment
and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and
operated in accordance with provided instructions and the antenna(s) used for this transmitter
must be installed to provide a separation distance of at least 20 cm from all persons and must
not be co-located or operating in conjunction with any other antenna or transmitter. End-users
and installers must be provided with antenna installation instructions and consider removing the
no-collocation statement.

Hereby, Ring LLC declares that this consumer electronic is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC. The
declaration of conformity may be consulted at www.ring.com/DoC.pdf.

04_Spotlight_Cam_Wired_2_LEGAL.indd 1 6/19/19 3:29 PM

Canada Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired
operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and
compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure
and compliance.

Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de
RSS 102 et la conformité à l’exposition de RSS-102 rf, utilisateurs peut obtenir l’information
canadienne sur l’exposition et la conformité de rf.

This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre
antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance
minimum de 20 centimètres entre le radiateur et votre corps.

04_Spotlight_Cam_Wired_2_LEGAL.indd 2 6/19/19 3:29 PM