120mm
90mm
Transformer
Smart Lighting
Landscape_Transformer_Manual.indd 1 1/17/19 5:39 PM
Maximum wattage load is 200 watts. Verify that the combined total
For your safety...
WARNING - Risk of electric shock. Do not mount
power supply or luminaires within 10 feet (3.0
meters) of a pool, spa, or fountain.
CAUTION: For use only on a branch circuit
protected by a Class A type Ground Fault Circuit
Interrupter (GFCI).
When used outdoors, install only to a covered Class A GFCI protected
receptacle that is weatherproof with the power unit connected to
the receptacle. If one is not provided, contact a qualified electrician
for proper installation. Ensure that the power unit and cord do not
interfere with completely closing the receptacle cover.
Transformer must be installed greater than 1 foot above ground level.
Landscape_Transformer_Manual.indd 3 1/17/19 5:39 PM
wattage of all fixtures is below 200W (for best results, do not exceed
140W).
For use with landscape lighting systems only.
Use with 12V or 15V landscape lights, including LED and halogen lights.
Use O N LY with common gauge sizes of CSA or UL approved low
voltage cable (12-16 AWG).
DO NOT use with an extension cord.
DO NOT connect two or more power supplies in parallel.
This manual is for informational purposes only. Working with electricity
can be dangerous unless proper safety precautions are taken. If you
are not comfortable or are inexperienced with the processes and
tools described in this manual, we recommend that you hire a licensed
electrician.
32
1. Set up your Transformer.
Download the Ring app.
The app walks you through setting up and
managing your Ring Transformer.
Download it on your iOS or Android device.
Landscape_Transformer_Manual.indd 5 1/17/19 5:39 PM
Set up your Ring Bridge.
The Bridge connects
your Ring Transformer
to the Ring app and
other compatible Ring
devices.
To set up your Bridge,
follow the instructions in
the Ring app or Bridge
user manual.
54
Choose a location.
Insert the top screws.
You’ll have to plug in your Transformer, so the
best place for it is near an outlet (make sure it’s
Drive the top screws first, leaving 1/8” of space
between the mounting surface and screw heads.
a covered, weatherproof Class A GFCI protected
outlet).
Once you’ve decided on a spot, use the included
1/8”
mounting template to mark the screw holes.
To avoid damage to your Transformer, make sure
the bottom screw is at least 1 foot above the
ground.
Mount your Transformer.
Align the Transformer with the top screws. Slide
it down over the screws to lock it into place. Then
drive the bottom screw to secure your Transformer.
76
Landscape_Transformer_Manual.indd 6-7 1/17/19 5:39 PM
2. Install lights and wiring.
Choose a cable.
0-50
Watts
Wire Length *
0-50 Feet 51-100
Feet
101-150
Feet
16 AWG 16 AWG 14 AWG
Your Transformer doesn’t come with low voltage
cable, so you’ll have to buy some online or at a home
improvement store. This chart might help.
Ensure the total fixture wattage does not exceed the
maximum wattage load of the Transformer.
51-100
Watts
100-200
Watts
Total Light Wattage
To get the total wattage, add up the wattage of each
fixture (example: 10 fixtures at 5W each is 50W total
watt age).
Landscape_Transformer_Manual.indd 9 1/17/19 5:39 PM
* Make sure your cable is long enough to reach all light fixtures. Consult cable
manufacturer if additional wire length or connectors are needed.
** Only use 15V Tap when the wire length is over 100 feet and total wattage is over
100 Watts. 12V Tap is recommended for all other cases.
16 AWG 14 AWG 12 AWG
14 AWG 12 AWG 12 AWG
with 15V
Tap **
98
Place light fixtures.
Connect cable to Transformer.
If you’re installing a new system, decide where you
would like to place your lights (not included), and
arrange them in the desired locations.
Open the Transformer door.
Hold it open to access the terminals.
Split and strip the cable.
Flip open the terminals, and feed one end of
the cable through the rubber grommet into the
Common terminal (left), and the other into either
the 12V (center) or 15V terminal (right) based on the
cable wattage you chose.
Then close the terminals and the access door.
The rubber grommet can be removed to
identify the terminals. Just make sure you
don’t lose it!
11
Landscape_Transformer_Manual.indd 10-11 1/17/19 5:39 PM
Run cable to fixtures.
Starting at the Transformer, run the cable to each
light fixture, leaving about 12” of cable after the last
fixture.
Leave a little extra cable at each fixture in case you have to adjust their
location.
Connect the wires.
Secure the light fixtures to the cable according to
the fixture manufacturer’s instructions.
12
Landscape_Transformer_Manual.indd 13 1/17/19 5:39 PM
Plug the Transformer into the
power outlet.
Your Transformer must be connected to a covered,
weatherproof GFCI protected receptacle. If you
don’t have a covered, weatherproof GFCI protected
receptacle, you’ll need to hire a licensed electrician
to install one.
Once plugged in, the button on
the front of your Transformer will
pulse red. Press the button. When
it turns solid red, your Transformer
is powered on.
Smart Lighting
Alarm
Doorbells
Security Cams
Chimes
Bury wiring cable.
Dig a shallow trench (up to 6” deep) along the wiring
route. Bury the wiring cable inside the trench.
Complete Setup
in the Ring app.
In the app, tap Set Up a
Device.
Connect your lighting to Ring.
Press and hold the button on the front of your
Transformer for 5 seconds.
Once it starts flashing
blue, it’s ready to pair
with the Ring app.
Landscape_Transformer_Manual.indd 15 1/17/19 5:39 PM
When prompted,
select Smart Lighting
and follow the in-app
instructions.
1514
For additional help, visit: ring.com/help
Or give us a call…
US 1 800 656 1918
Canada 1 855 300 7289
Worldwide +1 310 929 7085
For a list of all our customer support numbers, visit:
ring.com/callus
To review your wa rranty cove rage, plea se visit ww w.ring.com/warranty.
Patents: www.ring .com/patents
© 2019 Ring LLC or its a liates.
Ring, Ale xa, Always Ho me, and all rel ated logos ar e trademark s of Amazon .com, Inc. or i ts aliates .
Last updated: 01/17/19
Landscape_Transformer_Manual.indd 16 1/17/19 5:39 PM
Warnings
This device complies with part 15 of the FCC Rules and
Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must
accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
de moin de 20 cm. Installer les antennes de facon à ce que
le personnel ne puisse approcher à 20 cm ou moins de la
position centrale de l’ antenne.
Caution: Any changes or modifications to this device not
explicitly approved by manufacturer could void your
authority to operate this equipment.
MPE Reminding
To satisfy FCC / IC RF exposure requirements, a separation
distance of 20 cm or more should be maintained between
the antenna of this device and persons during device
operation.
To ensure compliance, operations at closer than this
distance is not recommended.
Les antennes installées doivent être situées de facon à ce
que la population ne puisse y être exposée à une distance
La FCC des éltats-unis stipule que cet appareil doit être en
tout temps éloigné d’au moins 20 cm des personnes
pendant son functionnement.
Loading...