RIKON Power Tools 60-100 User Manual

1HP Dust Collector

Model: 60-100

Record the serial number and date of purchase

in your manual for future reference.

Serial number:

Date of purchase:

www.rikontools.com or [e-mail]

Part # 60-100M2

[e-mail] or 877-884-5167

Owner’s Manual

For more information:

For Parts or Questions:

Operator Safety: Required Reading

IMPORTANT! Safety is the single most important consideration in the operation of this equipment.
The following instructions must be followed at all times.

There are certain applications for which this tool was designed. We strongly recommend that this tool

not be modied and/or used for any other application other than that for which it was designed. If you

have any questions about its application, do not use the tool until you have contacted us and we have
advised you.

General Safety Warnings

KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s

applications, work capabilities, and its specic potential hazards.

ALWAYS GROUND ALL TOOLS.

If your tool is equipped with a three-pronged plug, you must plug it into a three-hole electric receptacle.
If you use an adapter to accommodate a two-pronged receptacle, you must attach the adapter plug to a

known ground. Never remove the third prong of the plug.

ALWAYS AVOID DANGEROUS ENVIRONMENTS.
Never use power tools in damp or wet locations. Keep your work area well lighted and clear of clutter.

ALWAYS REMOVE THE ADJUSTING KEYS AND WRENCHES FROM TOOLS AFTER USE.

Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before
turning it on.

ALWAYS KEEP YOUR WORK AREA CLEAN. Cluttered areas and benches invite accidents.

ALWAYS KEEP VISITORS AWAY FROM RUNNING MACHINES.

All visitors should be kept a safe distance from the work area.

ALWAYS MAKE THE WORKSHOP CHILDPROOF.
Childproof with padlocks, master switches, or by removing starter keys.

NEVER OPERATE A TOOL WHILE UNDER THE INFLUENCE OF DRUGS,
MEDICATION, OR ALCOHOL.

ALWAYS WEAR PROPER APPAREL.

Never wear loose clothing or jewelry that might get caught in moving parts. Rubber-soled footwear is
recommended for the best footing.

ALWAYS USE SAFETY GLASSES AND WEAR HEARING PROTECTION.
Also use a face or dust mask if the cutting operation is dusty.

NEVER OVERREACH.
Keep your proper footing and balance at all times.

NEVER STAND ON TOOLS.
Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.

2

ALWAYS DISCONNECT TOOLS.
Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters.

ALWAYS AVOID ACCIDENTAL STARTING.
Make sure switch is in “OFF” position before plugging in cord.

NEVER LEAVE TOOLS RUNNING UNATTENDED.

ALWAYS CHECK FOR DAMAGED PARTS.

Before initial or continual use of the tool, a guard or other part that is damaged should be checked to
assure that it will operate properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its
operation. A guard or other damaged parts should immediately be properly repaired or replaced.

Special Safety Rules For Dust Collectors

1. Do not operate this machine until you have read all of the following instructions.

2. Do not attempt to operate this machine until it is completely assembled.

3. Do not turn ON this machine if any pieces are missing.

4. If you are not familiar with the operation of the machine, obtain assistance from a qualied

person.

5. It is highly recommended that this machine be placed on a level surface.

6. Always wear protective eyewear prior to operating this machine.

7. Do not operate this machine if you are under the inuence of drugs and/or alcohol.

8. Remove all jewelry prior to operating this machine.

9. Do not wear any gloves while operating this machine.

10. Always make sure the power switch is in the OFF position prior to plugging in the machine.

11. Always make sure the power switch is in the OFF position when doing any assembly or setup
operation.

12. Always wear a dust mask when cleaning or working near a dust collector.

13. The use of any accessories or attachments not recommended may cause injury to you and
damage your machine.

14. This machine must be properly grounded.

15.Always keep your face and hands clear of moving parts such as impellors and fans.

16.Keep these instructions for future reference.

California Proposition 65 Warning

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to the State of California to cause cancer and birth defects or
other reproductive harm.Your risk from exposure to these chemicals varies, depending on how often
you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved

safety equipment, such as dust masks that are specially designed to lter out microscopic particles.

For more detailed information about California Propostion 65 visit www.rikontools.com.

SAVE THESE INSTRUCTIONS.

Refer to them often.

3

Table of Contents

Safety Warnings.............................................................................................................................................2-3

Dust Collector Safety Rules .......................................................................................................................3

Specications ........................................................................................................................................4

Contents of Package .........................................................................................................................................5

Assembly ...........................................................................................................................6-8

Oper atio n.... .... .... ..... .... ..... .... ..... .... ..... .... .... ..... .... ..... .... ..... .... ......... .... ..... .... ..... ..9

Dust Hazards and Safety..............................................................................................................9

Electrical Requirements ...............................................................................................................................10

Trouble Shooting...............................................................................................................................................11

Wiring Diagram......................................................................................................................................11

Parts List .....................................................................................................................................12

Parts Explosion...........................................................................................................................................13

Warranty .............................................................................................................................................14

Notes............................................................................................................................................15

Specications

Model #
Cubic Feet Per Min
Motor
Motor Speed
Blower Wheel Diameter
Sound Rating @ 3 ft.
Bag Filtration
Bag Diameter
Bag Capacity
Bag Length
Hose Connection
Overall Dimensions

Net Weight 66 lbs

60-100
650 CFM
1HP, 115V, 7.9A
3450RPM
9”
78dB
5 Microns

14-3/4”

2.1 Cu.Ft.
26”
1@4”

32-1/4””(L) x 15”(W) x 60”(H)

4

Contents of Package

When unpacking, check to make sure the following parts are included. If any parts are missing
or broken, please call RIKON Power Tools at the number on the cover of this manual as soon as

possible.

A

B

A
B
C
D
E
F
G

C

D

E

F

Upper bag support
Vertical supports
Base plate
Spacer blocks
Bag of casters
Column
Rubber gasket

H

G

J

L

I

H

I

J
K
L
M

K

Handle
Collector housing
Straps
Dust bags
Motor & housing
Bag of loose parts

M

5