Rikon Power Tools 11-200 Operator's Manual
11-200
10” Deluxe Cabinet Saw
Operator’s Manual
Record the serial number and date of purchase in your manual for future reference.
Serial Number: _________________________ Date of purchase: _________________________
For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167
11-200M1
www.rikontools.com
TABLE OF CONTENTS
Specications.....................................................................................................................2
Safety Instructions ......................................................................................................3 - 6 & 23 - 24
Getting To Know Your Cabinet Saw ..............................................................................................7
Contents of Package .....................................................................................................8 - 9
Installation ......................................................................................................................10
Assembly ................................................................................................................. 10 - 15
Adjustments...............................................................................................................16 - 21
Operation ..................................................................................................................22 - 24
Maintenance ....................................................................................................................25
Electricals & Wiring Diagram .......................................................................................5, 22 & 25
Troubleshooting .........................................................................................................26
Notes ...............................................................................................................................27
Parts Diagrams & Parts Lists ..................................................................................28 - 37
Warranty ..........................................................................................................................38
Accessories ..........................................................................................................39
SPECIFICATIONS
Motor ............................................................................................. 1.75 HP, TEFC
Motor Speed (no load)......................................................................... 3,450 RPM
Volts ................................................................................................... 120 / 240 V
Amps, Hertz, Phase ........................................................... 15 / 7.5 A, 60 Hz, 1Ph
Blade Diameter..................................................................................10” (254 mm)
Blade Arbor.........................................................................................5/8” (16 mm)
Blade Speed ........................................................................................ 3,450 RPM
Blade Tilt ......................................................................................................... Left
Max Depth of Cut @ 90
Max Depth of Cut @ 45
°
............................................................................... 3-3/8”
°
............................................................................... 2-1/4”
Table Size (W x D) ......................................56-1/4” x 27” (1428.75 x 685.80 mm)
Table Height ......................................................................... 35-1/4” (895.35 mm)
Miter Gauge T-Slots (2) ......................................................................... 3/4” x 5/8”
Fence Height ............................................................................ 2-5/8” (66.68 mm)
Max Rip Capacity (right of blade)..................................................... 30” (762 mm)
Dust Ports (1) ..................................................................... 4” Diameter (100 mm)
Height ...................................................................................... 42” (1,066.80 mm)
Width ................................................................................. 64-1/4” (1,631.95 mm)
Depth ....................................................................................... 42” (1,066.80 mm)
Net Weight .............................................................................
NOTE: The specications, photographs, drawings and information in this manual represent the current model when the
manual was prepared. Changes and improvements may be made at any time, with no obligation on the part of Rikon
Power Tools, Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in
this manual is correct, to provide you with the guidelines for the proper safety, assembly and operation of this machine.
355 lbs (161.03 kg)
2
SAFETY INSTRUCTIONS
IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following
instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock,
re, and/or serious personal injury.
There are certain applications for which this tool was designed. We strongly recommend that this tool not be modied
and/or used for any other application other than that for which it was designed. If you have any questions about its
application, do not use the tool until you have contacted us and we have advised you.
SAFETY SYMBOLS
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION. This symbol may be used
in conjunction with other symbols or pictographs.
Indicates an imminently hazardous situation, which, if not avoided, could result in death or
serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious
injury.
Indicates a potentially hazardous situation, which, if not avoided, could result in minor or
moderate injury.
NOTICE: Shown without Safety Alert Symbol indicates a situation that may result in property damage.
GENERAL SAFETY
KNOW YOUR POWER TOOL. Read the owner’s manual
carefully. Learn the tool’s applications, work capabilities,
and its specic potential hazards.
4. AVOID A DANGEROUS WORKING ENVIRONMENT.
DO NOT use electrical tools in a damp environment or
expose them to rain.
BEFORE USING YOUR MACHINE
To avoid serious injury and damage to the tool, read and
follow all of the Safety and Operating Instructions before
operating the machine.
1. Some dust created by using power tools contains
chemicals known to the State of California to cause cancer,
birth defects, or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and other
• masonry products.
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area and work
with approved safety equipment, such as those dust masks
that are specially designed to lter out microscopic
particles.
2. READ the entire Owner’s Manual. LEARN how to use
the tool for its intended applications.
3. GROUND ALL TOOLS. If the tool is supplied with a 3
prong plug, it must be plugged into a 3-contact electrical
receptacle. The 3rd prong is used to ground the tool and
provide protection against accidental electric shock. DO
NOT remove the 3rd prong. See Grounding Instructions
on the following pages.
5. DO NOT use electrical tools in the presence of
ammable liquids or gasses.
6. ALWAYS keep the work area clean, well lit, and
organized. DO NOT work in an environment with oor
surfaces that are slippery from debris, grease, and wax.
7. KEEP VISITORS AND CHILDREN AWAY. DO NOT
permit people to be in the immediate work area,
especially when the electrical tool is operating.
8. DO NOT FORCE THE TOOL to perform an operation
for which it was not designed. It will do a safer and
higher quality job by only performing operations for
which the tool was intended.
9. WEAR PROPER CLOTHING. DO NOT wear loose
clothing, gloves, neckties, or jewelry. These items can
get caught in the machine during operations and pull the
operator into the moving parts. The user must wear a
protective cover on their hair, if the hair is long, to
prevent it from contacting any moving parts.
10. CHILDPROOF THE WORKSHOP AREA by
removing switch keys, unplugging tools from the
electrical receptacles, and using padlocks.
11. ALWAYS UNPLUG THE TOOL FROM THE
ELECTRICAL RECEPTACLE when making adjustments, changing parts or performing any maintenance.
3
SAFETY INSTRUCTIONS
12. KEEP PROTECTIVE GUARDS IN PLACE AND IN
WORKING ORDER.
13. AVOID ACCIDENTAL STARTING. Make sure that
the power switch is in the “OFF” position before plugging
in the power cord to the electrical receptacle.
14. REMOVE ALL MAINTENANCE TOOLS from the
immediate area prior to turning “ON” the machine.
15. USE ONLY RECOMMENDED ACCESSORIES. Use
of incorrect or improper accessories could cause serious
injury to the operator and cause damage to the tool. If in
doubt, check the instruction manual that comes with that
particular accessory.
16. NEVER LEAVE A RUNNING TOOL UNATTENDED.
Turn the power switch to the “OFF” position. DO NOT
leave the tool until it has come to a complete stop.
17. DO NOT STAND ON A TOOL. Serious injury could
result if the tool tips over, or you accidentally contact the
tool.
18. DO NOT store anything above or near the tool where
anyone might try to stand on the tool to reach it.
19. MAINTAIN YOUR BALANCE. DO NOT extend
yourself over the tool. Wear oil resistant rubber soled
shoes. Keep oor clear of debris, grease, and wax.
25. ALWAYS WEAR A DUST MASK TO PREVENT
INHALING DANGEROUS DUST OR AIRBORNE
PARTICLES, including wood dust, crystalline silica dust
and asbestos dust. Direct particles away from face and
body. Always operate tool in well ventilated area and
provide for proper dust removal. Use dust collection
system wherever possible. Exposure to the dust may
cause serious and permanent respiratory or other injury,
including silicosis (a serious lung disease), cancer, and
death. Avoid breathing the dust, and avoid prolonged
contact with dust. Allowing dust to get into your mouth
or eyes, or lay on your skin may promote absorption of
harmful material. Always use properly tting NIOSH/OSHA
approved respiratory protection appropriate for the dust
exposure, and wash exposed areas with soap and water.
26. USE A PROPER EXTENSION CORD IN GOOD
CONDITION. When using an extension cord, be sure to
use one heavy enough to carry the current your product
will draw. The table on the following page shows the correct size to use depending on cord length and nameplate
amperage rating. If in doubt, use the next heavier gauge.
The smaller the gauge number, the larger diameter of the
extension cord. If in doubt of the proper size of an extension cord, use a shorter and thicker cord. An undersized
cord will cause a drop in line voltage resulting in a loss of
power and overheating.
USE ONLY A 3-WIRE EXTENSION CORD THAT HAS
A 3-PRONG GROUNDING PLUG AND A 3-POLE
RECEPTACLE THAT ACCEPTS THE TOOL’S PLUG.
20. MAINTAIN TOOLS WITH CARE. Always keep tools
clean and in good working order. Keep all blades and tool
bits sharp, dress grinding wheels and change other
abrasive accessories when worn.
21. EACH AND EVERY TIME, CHECK FOR DAMAGED
PARTS PRIOR TO USING THE TOOL. Carefully check
all guards to see that they operate properly, are not damaged, and perform their intended functions. Check for
alignment, binding or breaking of moving parts. A guard
or other part that is damaged should be immediately
repaired or replaced.
22. DO NOT OPERATE TOOL WHILE TIRED, OR
UNDER THE INFLUENCE OF DRUGS, MEDICATION
OR ALCOHOL.
23. SECURE ALL WORK. Use clamps or jigs to secure
the work piece. This is safer than attempting to hold the
work piece with your hands.
24. STAY ALERT, WATCH WHAT YOU ARE DOING,
AND USE COMMON SENSE WHEN OPERATING A
POWER TOOL.
A moment of inattention while operating power tools may
result in serious personal injury.
27. ADDITIONAL INFORMATION regarding the safe and
proper operation of this product is available from:
• Power Tool Institute
1300 Summer Avenue
Cleveland, OH 44115-2851
www.powertoolinstitute.org
• National Safety Council
1121 Spring Lake Drive
Itasca, IL 60143-3201
www.nsc.org
• American National Standards Institute
25 West 43rd Street, 4th Floor
New York, NY 10036
www.ansi.org
• ANSI 01.1 Safety Requirements for
Woodworking Machines and the
U.S. Department of Labor regulations
www.osha.gov
28. SAVE THESE INSTRUCTIONS. Refer to them
frequently and use them to instruct others.
4
SAFETY INSTRUCTIONS
ELECTRICAL SAFETY
THIS TOOL IS PRE-WIRED FOR 120V
CIRCUITS, AND MUST BE GROUNDED WHILE IN USE TO
PROTECT THE OPERATOR FROM ELECTRIC SHOCK.
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,
grounding provides the path of least resistance for electric
current and reduces the risk of electric shock. This tool
is equipped with an electric cord that has an equipment
grounding conductor and requires a grounding plug (not
included). The plug MUST be plugged into a matching electrical receptacle that is properly installed and grounded in
accordance with ALL local codes and ordinances.
DO NOT MODIFY ANY PLUG. If it will not t the electrical
receptacle, have the proper electrical receptacle installed
by a qualied electrician.
IMPROPER ELECTRICAL CONNECTION of the
equipment grounding conductor can result in risk of
electric shock. The conductor with the green insulation
(with or without yellow stripes) is the equipment grounding conductor. DO NOT connect the equipment grounding
conductor to a live terminal if repair or replacement
of the electric cord or plug is necessary.
EXTENSION CORDS
THE USE OF AN EXTENSION CORD
WITH THIS MACHINE IS NOT RECOMMENDED. For
best power and safety, plug the machine directly into a
dedicated, grounded electrical outlet that is within the
supplied cord length of the machine.
If an extension cord needs to be used, it should only be
for a limited operation of the machine. The extension
cord should be as short as possible in length, and have
a minimum gauge size of 14AWG.
Check extension cords before each
use. If damaged replace immediately. Never use a tool
with a damaged cord, since touching the damaged area
could cause electrical shock, and serious injury.
Use a proper extension cord. Only use cords listed by
Underwriters Laboratories (UL). Other extension cords can
cause a drop in line voltage, resulting in a loss of power
and overheating of tool. When operating a power tool outdoors, use an outdoor extension cord marked “W-A” or “W”.
These cords are rated for outdoor use and reduce the risk
of electric shock.
CHECK with a qualied electrician or service personnel if
you do not completely understand the grounding
instructions, or if you are not sure the tool is properly
grounded when installing or replacing a plug.
USE ONLY A 3-WIRE EXTENSION CORD THAT HAS
THE PROPER TYPE OF A 3-PRONG GROUNDING PLUG
THAT MATCHES THE MACHINE’S 3-PRONG PLUG AND
ALSO THE 3-POLE RECEPTACLE THAT ACCEPTS THE
TOOL’S PLUG. * See Figures A and B.
REPLACE A DAMAGED OR WORN CORD
IMMEDIATELY.
This tool is intended for use on a circuit that has a 120
volt electrical receptacle. FIGURE C shows the type of the
240V, 3-wire electrical plug and electrical receptacle that
has a grounding conductor that is required if the motor
wiring is changed. See page 25.
FIG. A
FIG. B
COVER
RAILS
Keep the extension cord clear of
the working area. Position the cord so that it will not
get caught on lumber, tools or other obstructions while
you are working with your power tool.
* Canadian electrical codes require extension cords to
be certied SJT type or better.
** The use of an adapter in Canada is not acceptable.
FIG. C
Sample of 240 volt plug
required for this machine.
Consult a qualied
electrician if the
distance of the
machine from the
electrical panel is
greater than 30 feet.
5
SAFETY INSTRUCTIONS
SPECIFIC SAFETY INSTRUCTIONS FOR TABLE SAWS
This machine is intended for the cutting of natural and solid woods.The permissible workpiece dimensions must be
observed (see Technical Specification). Any other use not as specified, including modification of the machine or use of
parts not tested and approved by the equipment manufacturer, can cause unforeseen damage and invalidate the warranty.
ATTENTION: Use of this table saw still presents risks that cannot be eliminated by the manufacturer. Therefore, the user
must be aware that wood working machines are dangerous if not used with care and all safety precautions are adhered to.
1. ALWAYS USE SAW BLADE GUARD, splitter and anti-kickback pawls for every through-sawing operation.
Through-sawing operations are those in which the blade cuts completely through the workpiece when ripping or
crosscutting. Always be sure blade guard is tightly secured.
2. ALWAYS HOLD WORK FIRMLY against the miter gauge or rip fence.
3. ALWAYS USE a push stick, especially when ripping narrow stock.
4. NEVER PERFORM ANY OPERATIONS FREEHAND, which means using only your hands to support or guide the
workpiece. Always use either the fence or the miter gauge to position and guide the work. WARNING: FREEHAND
CUTTING IS THE MAJOR CAUSE OF KICKBACK AND FINGER/HAND AMPUTATIONS.
5. NEVER STAND or have any part of your body in line with the path of the saw blade. Keep your hands out of the saw
blade path.
6. NEVER REACH behind or over the cutting tool for any reason.
7. FEED WORK INTO THE BLADE against the direction of rotation only.
8. NEVER use the rip fence as a cut-o gauge when crosscutting.
9. NEVER ATTEMPT TO FREE A STALLED SAW BLADE without rst turning the saw OFF. Turn power switch OFF
immediately to prevent kickback and motor damage.
10. PROVIDE ADEQUATE SUPPORT to the rear and the sides of the table saw for long or wide workpieces.
11. AVOID KICKBACKS (work thrown back towards you) by keeping the blade sharp, the rip fence parallel to the saw
blade and by keeping the splitter, anti-kickback pawls and guards in place, aligned and functioning. Do not release
work before passing it completely beyond the saw blade. Do not rip work that is twisted, warped or does not have a
straight edge to guide it along the fence.
12. AVOID AWKWARD OPERATIONS and hand positions where a sudden slip could cause your hand to move into the
saw blade.
13. NEVER USE SOLVENTS to clean plastic parts. Solvents could possibly dissolve or otherwise damage the material.
Only a soft damp cloth should be used to clean plastic parts.
14. NEVER CUT METALS or materials that make hazardous dust.
15. ALWAYS USE IN A WELL-VENTILATED AREA. Clean out sawdust from the interior of the saw to prevent a
pontenial re hazard.
16. NEVER LEAVE THE SAW RUNNING UNATTENDED. Do not leave the saw until blade comes to a complete stop.
SAVE THESE INSTRUCTIONS.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to the State of California to cause cancer and birth defects or other reproductive
harm. Your risk from exposure to these chemicals varies, depending on how often you do this type of work.
To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust
masks that are specially designed to lter out microscopic particles.
For more detailed information about California Proposition 65 log onto rikontools.com.
This owner’s manual is not a teaching aid. Use of this owner’s manual is intended to
show assembly, adjustments, and general use.
Refer to them often.
California Proposition 65 Warning
6
GETTING TO KNOW YOUR CABINET SAW
C
B
A
D E
F
G
H
I
J
K
L
A. Motor Cover
B. ON / OFF Switch
C. Rip Fence Rail
D. Miter Gauge
E. Blade Guard Assembly with Riving Knife
F. Rip Fence
G. Table Board
H. Blade Angle Handwheel
I. Fence Storage Hooks
J. Bevel Scale
K. Blade Height Handwheel
L. Mobility Kit Foot Pedal
7
CONTENTS OF PACKAGE
Model 11-200 10” Deluxe Cabinet Saw body is shipped complete in one box. The fence assembly is
shipped separately. Instructions for assembly and use of the fence are provided separate from this
manual.
Unpacking, Checking Contents & Clean-up
1. Carefully remove all contents from the shipping carton. Compare the contents with the list of contents to
make sure that all of the items are accounted for, before discarding any packing material. Place parts on a
protected surface for easy identication and assembly. If any parts are missing or broken, please call RIKON
Customer Service (877-884-5167) as soon as possible for replacements. DO NOT turn your machine ON if any
of these items are missing. You may cause injury to yourself or damage to the machine.
2. Report any shipping damage to your local distributor. Take photos for any insurance claims.
3. With the help of another person, carefully lift the saw from the packaging and place it on a level oor.
4. Clean all rust protected surfaces with ordinary house hold type grease or spot remover. Do not use;
gasoline, paint thinner, mineral spirits, etc. These may damage painted surfaces.
5. Apply a coat of paste wax to the table to prevent rust. Wipe all parts thoroughly with a clean dry cloth. Be
careful, as the blade has sharp teeth and may cause injury if touched.
6. Set packing material and shipping carton aside. Do not discard until the machine has been set up and is
running properly.
TABLE OF LOOSE PARTS
A. Main Saw Body
B. Cast Iron Extenstion Wings (2)
C. ON/OFF Switch Box and Wiring
D. Blade Guard and Splitter Assembly
E. Hand Wheels (2) Locking Knobs (2)
F. Miter Gauge, Wrenches & Push Stick
A
E
C
B
D
F
CONTINUED ON PAGE 9
8
CONTENTS OF PACKAGE
TABLE OF LOOSE PARTS continued
Extension Wing Screw Package:
A. M8 Flat Washer (8)
B. M8 Lock Washer (8)
C. 8mm x 50mm Hex Allen Bolt (8)
Fence Bracket Package:
D. M4 x 8mm Round HD Tap Screw (2)
E. Wrench Hook (1)
F. Fence Storage Bracket (2)
G. 1/4”-20 x 3/8” Round HD Tap Screw (4)
Dust Port Hardware Package:
H. Dust Port (1)
I. 1/4”-20 x 1/2” Round HD Tap Screw (4)
A
B
C
F
G
D
E
I
H
Caster Wheel Assembly Package
J. Caster Wheel with Foot Pedal (1)
K. M8 Hex Flange Nut (2)
L. M8 x 16 Carriage Bolt (2)
M. Wheel (2)
N.
Leveling Feet (2)
O. M8 Hex Nut (2)
P. M8 x 50mm Hex Head Bolt (2)
Q. M8 Flat Washer (2)
Spacer Package:
R. Spacer (for cast wing installation) (2)
K
N
L
M
O
J
P
Q
R
9
MOVING & INSTALLING THE SAW
INSTALLATION
The table saw is heavy - over 350
lbs! It is best to assemble the machine near the
area where it will eventually reside.
1. Carefully remove the machine from the shipping
carton. See above instructions on handling the saw.
2. Position the machine on a solid, level foundation
that is located in an area that has ample space in
front, right side and in back of the table saw for
cutting large or long material.
ASSEMBLY
• The table saw is a heavy machine; two people
may be required for certain assembly
operations.
• DO NOT assemble the table saw until you are
sure the tool is unplugged.
3. Align the machine so that during use, the material
being cut will not face aisles, doorways, or other work
areas that bystanders may be in. Do not locate or use
the machine in damp or wet conditions.
4. Once in place in your shop, lower the Foot
Pedal Assembly and level the machine with the two
Leveling Feet provided in the Mobility Kit Assembly
shown below.
• DO NOT assemble the table saw until you are
sure the power switch is in the "OFF" position.
• For your own safety, DO NOT connect the
machine to the power source until the machine
is completely assembled and you read and
understand this entire User Manual.
MOBILITY KIT ASSEMBLY
1. Lay the saw on its back. CAUTION: The table saw
is heavy; two people are needed to assist with this
procedure. Use a large section of cardboard to
protect the table and cabinet.
2. Thread two Leveling Feet to bottom of the right side
of the base
3. Install the Foot Pedal Assembly to side of base
using three Allen head cap screws M8 x 50mm, six
8mm at washers, three 8m lock washers and
three 8mm hex nuts
4. Install two Wheel Assemblies to bottom of the left
side of the base. Locate two wheels, two M8
washers and two M8 x 50mm hex bolts
5. Slide the bolts and washers through the frame and
wheel and thread into the opposite side of the
wheel pocket
6. With the help of another person, lift the saw upright
and test the operation of the mobility kit by de pressing the foot pedal.
(A-Fig. 1).
(B-Fig. 1).
(A-Fig. 2).
(B-Fig. 2).
A
B
A
B
FIGURE 1
FIGURE 2
10
ASSEMBLY
THE MACHINE MUST NOT BE
PLUGGED IN AND THE POWER SWITCH MUST BE IN
THE OFF POSITION UNTIL ASSEMBLY IS COMPLETE.
C
HANDWHEEL ASSEMBLY
1. Place one of the handwheels (A-Fig. 3) onto
the shaft to raise/lower the blade (B-Fig. 3)
located on the front of the cabinet. Align the
groove in the back of the handwheel with the
pin (C-Fig. 3).
2. Thread the locking knob (A-Fig. 4) onto the
threaded end of the shaft (C-Fig. 3).
3. Repeat the steps above to assemble the
remaining handwheel and locking knob onto
the blade angle shaft located on the right side
of the cabinet.
WRENCH AND FENCE HOOK
ASSEMBLY
1. Install both of the fence hooks (A-Fig. 5) to the
right side of the cabinet using two M4 x 8mm
tap screws for each hook.
A
B
FIGURE 3
A
FIGURE 4
B
2. Attach the wrench hook (B-Fig. 5) to the right
side of cabinet using two M4 X 8mm round
head tap screws.
DUST PORT INSTALLATION
1. Locate the dust port and four 1/4”-20 x 1/2”
Round HD Tap Screws from the package
contents.
2. Place the dust port over the opening located at
the bottom of the rear panel and attach using
the four screws (A-Fig. 6) with a Phillips head
screw driver.
A
FIGURE 5
A (x4)
FIGURE 6
11
ASSEMBLY
EXTENSION WING INSTALLATION
The extension wings are heavy; two
people are required for assembly.
1.One person is required to lift an extension wing into
position. The extension wing will sit into alignment
pins to help locate the postion.
A
2. The second person will install two spacers
(A-Fig.
7) into the table slot to ensure proper miter guage
operation.
3. Have the second person secure the extension wing
in place using four 5/16”-18 x 45mm hex socket
bolts, four M8 lock washers and four special wash ers. Bolts and washers will install up from inside
the cabinet into the bottom of the extension wing.
SEE FIG. 8.
TABLE LEVELING ADJUSTMENT
The pre-adjustment and setting of the extension
wings for level and atness have been performed at
the factory. Follow the instructions below if further
adustment is needed.
1. Use a long and accurate straight edge to check
table level and atness. Place the straight edge
onto the main table and check each wing separate ly and then all three castings at once. This will
ensure that the wings are level with the main table
as well as each other. SEE FIG. 9.
Front Bolts
(x2)
FIGURE 7
Rear Bolts
(x2)
FIGURE 8
2. Loosen the four small set screws (A-Fig. 10)
the side of the frame casting using a 2.5mm Allen
wrench.
3. Next, loosen slightly the four 5/16”-18 x 45mm hex
socket bolts (B-Fig. 10)
extension wings to the saw body.
4. Adjust the four thin elevation bolts found between
the top of the frame casting and the underside of
the extension wing using the 5/8” opening of the
blade wrench. SEE FIG. 10.
5. Check progress periodically with the straight edge
using steps described in the rst step above.
6. Once the table level and atness is achieved
tighten the four 5/16”-18 x 45mm hex socket bolts
and then the four small set screws on the side of
the frame casting to retain the setting.
previously used to attach
on
12
FIGURE 9
THIN BOLTS
A
B
FIGURE 10
BLADE
WRENCH
Loading...