
Troubleshooting
1. P rob e tip is br oke n off:
i. P rob es fall o ff or o ther ph ysi cal imp acts.
ii . Pro bes are c onnec ted w ith hot o bject s that ma ke me tal tip fade a nd the pl astic
pa rt me lt down .
Ti ps:
-Pl eas e do not ke ep the pr obe o n the tes t point s whe n it i s not u sed.
-Do n ot pu t high pr essur e on th e probe .
-Do n ot co nnect p robes w ith h ot obje cts.
2. P rob e wires a re br oken of f or ag ing:
i. The co nnect ion par t bet ween pr obes an d wir es are cu rled to o muc h.
ii . Pro be wires are t ighte ned and t wis ted.
Ti ps:
-Ho ld th e probe b ody and d o not c url the c onnec tio n part be tween p robes a nd wi res
to o muc h.
-Do n ot st rain or t wis t probe w ires.
3. Retract able ho ok tip is brok en off:
Probe i s shake n har dly aft er retract able ho ok ti p is conn ected w ith tes ted o bject s.
Ti ps:
-Do n ot sh ake the p rob e after r etractab le hook t ip is c onnec ted wit h teste d obj ects.
-Do n ot ke ep the re tra ctabl e hoo k tip on th e teste d objec ts wh en it is no t used.
4. Grou nd lead i s bro ken off o r mis sing:
i. Grou nd lead i s bro ken off w hen c onnec ting or d iscon nec ting th e probe .
i i. Stra in th e groun d lead af ter a ll iga tor cli p is conn ect ed with t he grou nd re feren ce.
Ti ps:
-You ’d be tter no t separate t he grou nd le ad from t he pr obe.
-Do n ot st rain th e gro und lea d after a lli gator c lip is co nnect ed wi th the gr ound
refer ence.
NOTES
CAT I : IEC M eas ure men t Cat ego ry I, w hic h is for measurements perfo rme d on ci rcu its n ot
di rectly connected to AC line under Category I overv olt age c ond iti ons .
.
性能指标 (Technical Specifications)
10 :1 (Fixed )
CAT I 7 VAC
一般规格 (Genera l Sp ec if icat io ns)
145 2cm
About 4 6g
3
4
RP6150无源 探头
RP6150 Passive Probe

附件 说 明
常见 故 障
1.探针 折断
成因:
i. 探头 跌落 或 物理 冲击导 致探 针 折断 。
ii. 探 针与 过 热的 测试点 连接 导 致金 属针褪 色、 探针连 接塑料 部分 融化。
操作提 示:
-探头 不使 用 时, 请勿将 探针 留 在被 测装置 的被 测点( 孔)处 。
-防止 给探 头 过度 施压。
-避免 探针 与 过热 物体连 接。
2.电缆 线折 断 或老 化
成因 :
i. 在操 作过 程 中过 度弯曲 探头 和 电缆 线连接 部位 。
ii. 在 操作 过 程中 或存放 时电 缆 线被 过度拉 紧、 缠绕。
操作提 示:
-手握 探头 时 需握 在坚实 部位 , 避免 过度弯 曲探 头和电 缆线连 接处 。
-避免 用力 拉 扯电 缆线, 存放 时 避免 电缆线 缠绕 。
3.探头 钩折 断
成因:
探头钩 固定 在 被测 物后, 用力 摇 晃导 致探头 钩折 断。
操作提 示:
-探头 钩固 定 在被 测物后 ,请 勿 用力 拉扯或 大幅 度摇晃 。
-当探 头不 使 用时 ,请勿 将探 头 钩继 续挂在 被测 装置上 。
4.接地 线折 断 或丢 失
成因:
i.在连 接或 分 开探 头和接 地卡 时 ,拉 断接地 线。
ii.接 地鳄 鱼 夹连 接被测 装置 的 地线 以后, 仍用 力拉扯 导致拉 断接 地线。
操作提 示:
—尽量 避免 分 开接 地卡与 探头 。
—接地 鳄鱼 夹 固定 在被测 物后 , 请勿 用力拉 扯或 大幅度 摇晃。
注意 事 项
BNC Con necto r Plug: B e conne cted to t he
oscil losco pe meas uring c hanne l.
CAT I:IEC测 量 类别I 在类别I过 压情 况 下,用于 在不直 接连 接 到市 电的电 路上 进行的 测量。 。
设备 通过双 重绝 缘或 加强 结缘 保护 。