RIGOL RIGOL MEM-DG1000 Datasheet

DG1000Z

Series

Function/Arbitrary
Waveform Generator

SiFi (Signal Fidelity) for 100% waveform replication

2Mpts or 8Mpts/CH(std.), 16Mpts/CH (opt.) arbitrary waveform length

Standard 2 full functional independent channels

±1ppm frequency stability, -125dBc/Hz phase noise, 200ps low jitter

Built-in 8 orders harmonics generator

Built-in 7 digits/s counter up to 200MHz

160 built-in pre-edited waveforms

Intuitive arbitrary waveform editing software

Full modulation supported: AM, FM, PM, ASK, FSK, PSK and PWM

DG1000Z series function/arbitrary waveform generator is a multi-

functional generator that combines many functions in one, including

Function Generator, Arbitrary Waveform Generator, Noise Generator,

Pulse Generator, Harmonics Generator, Analog/Digital Modulator and

Counter. As a multi-functional, high performance and portable generator,

it will be a new selection in education, R&D, production, test and etc.

RIGOL

TECHNOLOGIES, INC.

DG1000Z Series Function/Arbitrary Waveform Generator

Dimensions: Width×Height×Depth=261.5mm×112mm×318.4mm

Weight: 3.2kg (without package)

1

RIGOL

Feature and Benets

Standard 2 full functional channels

Burst function

Arbitrary waveform function with
innovative SiFi technology

Multiple analog and digital modulations

Up to 160 built-in waveforms

Sweep function

Standard harmonic generator

Channels and system setting

Waveform summing function

In line with LXI Core 2011 Device File Management Function

Standard 7 digits/s full function frequency
counter with 200MHz bandwidth

2

RIGOL

Specications

All the specications can be guaranteed if the following two conditions are met unless where noted.

· The generator is within the calibration period and has performed self-calibration.

· The generator has been working continuously for at least 30 minutes under the specied temperature (18℃ ~ 28℃).
All the specications are guaranteed unless those marked with “typical”.

Model DG1022Z DG1032Z DG1062Z
Channel 2 2 2

Max Frequency 25 MHz

Sample Rate 200 MSa/s

Waveform
Basic Waveform Sine, Square, Ramp, Pulse, Noise

Built-in Arbitrary Waveform

Frequency Characteristics
Sine 1 μHz to 25 MHz 1 μHz to 30 MHz 1 μHz to 60 MHz
Square 1 μHz to 25 MHz 1 μHz to 25 MHz 1 μHz to 25 MHz
Ramp 1 μHz to 500 kHz
Pulse 1 μHz to 15 MHz 1 μHz to 15 MHz 1 μHz to 25 MHz
Harmonic 1uHz to 10 MHz 1 μHz to 10 MHz 1uHz to 20 MHz
Noise (-3dB) 25 MHz bandwidth 30 MHz bandwidth 60 MHz bandwidth
Arbitrary Waveform 1 μHz to 10 MHz 1 μHz to 10 MHz 1 μHz to 20 MHz
Resolution 1 μHz
Accuracy ±1 ppm of the setting value, 18℃to 28

160 kinds, including Sinc, Exponential Rise, Exponential Fall, ECG, Gauss, HaverSine, Lorentz,
Dual-Tone, etc.

30 MHz 60 MHz

1 μHz to 500 kHz

℃

1 μHz to 1 MHz

Sine Wave Spectrum Purity

Typical (0 dBm)

Harmonic Distortion

Total Harmonic Distortion <0.075% (10 Hz to 20 kHz, 0 dBm)

Spurious (non-harmonic)

Phase Noise

Signal Characteristics

Square

Rise/Fall Time

Overshoot

Duty Cycle 0.01% to 99.99% (limited by the current frequency setting)
Non-symmetry 1% of the period + 5 ns

Jitter (rms)

Ramp

Linearity ≤1% of peak output (typical, 1 kHz, 1 VPP, 100% symmetry)
Symmetry 0% to 100%

Pulse

Pulse Width 16ns to 999.999 982 118ks (limited by the current frequency setting)
Duty Cycle 0.001% to 99.999% (limited by the current frequency setting)
Rising/Falling Edge ≥10 ns (limited by the current frequency setting and pulse width setting)

Overshoot

Jitter (rms)

Arbitrary Waveform

Waveform Length

DC-10 MHz (included): <-65 dBc
10 MHz to 30 MHz (included): <-55 dBc
30 MHz to 60 MHz (included): <-50 dBc

Typical (0 dBm)

≤10 MHz: <-70 dBc

>10 MHz: <-70 dBc + 6 dB/octave
Typical (0 dBm, 10 kHz offset)

10 MHz: <-125 dBc/Hz

Typical (1 Vpp)
<10ns

Typical (100 kHz, 1 Vpp)

≤5%

Typical (1 Vpp)

≤5 MHz: 2 ppm + 200 ps

> 5 MHz: 200 ps

Typical (1 Vpp)

≤5%

Typical (1 Vpp)

≤5 MHz 2 ppm + 200 ps

> 5 MHz 200 ps

2Mpts (std.)
16Mpts (opt.)

8Mpts (std.)
16Mpts (opt.)

8Mpts (std.)
16Mpts (opt.)

3

RIGOL

Vertical Resolution 14 bits
Sample Rate 200MSa/s

Min Rise/Fall Time

Jitter (rms)

Editing Mode Point Edit, Block Edit, Insert Waveform

Harmonic Output

Harmonic Order ≤8
Harmonic Type Even Harmonic, Odd harmonic, Order Harmonic, User
Harmonic Amplitude The amplitude of each order of harmonic can be set
Harmonic Phase The phase of each order of harmonic can be set

Output Characteristics

Amplitude (into 50 Ω)

Range

Accuracy

Flatness

Unit Vpp, Vrms, dBm
Resolution 0.1mVpp or 4 digits

Offset (into 50 Ω)

Range (Peak ac+dc) ±5Vpk ac+dc
Accuracy ±(1% of the setting value + 5mV + 0.5% of the amplitude)

Waveform Output

Output Impedance 50 Ω (typical)
Protection Short-circuit protection, automatically disable the waveform output when overload occurs

Typical (1 Vpp)
<10 ns

Typical (1 Vpp)

≤5 MHz: 2 ppm + 200 ps

> 5 MHz: 200 ps

≤10 MHz: 1.0 mVpp to 10 Vpp
≤30 MHz: 1.0 mVpp to 5.0 Vpp
≤60 MHz: 1.0 mVpp to 2.5 Vpp

Typical (1 kHz sine, 0 V offset, >10 mVpp, auto)
±(1% of the setting value) ±1 mV

Typical (sine, 2.5 Vpp)

≤10 MHz: ±0.1 dB
≤60 MHz: ±0.2 dB

Modulation Characteristics
Modulation Type AM, FM, PM, ASK, FSK, PSK, PWM

AM

Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External
Modulating Waveform Sine, Square, Ramp, Noise, Arb
Modulation Depth 0% to 120%
Modulating Frequency 2 mHz to 1 MHz

FM

Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External
Modulating Waveform Sine, Square, Ramp, Noise, Arb
Modulating Frequency 2 mHz to 1 MHz

PM

Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External
Modulating Waveform Sine, Square, Ramp, Noise, Arb
Phase Deviation 0° to 360°
Modulating Frequency 2 mHz to 1 MHz

ASK

Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External
Modulating Waveform Square with 50% duty cycle
Key Frequency 2 mHz to 1 MHz

FSK

Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External
Modulating Waveform Square with 50% duty cycle
Key Frequency 2 mHz to 1 MHz

PSK

Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Source Internal/External

4

RIGOL

Modulating Waveform Square with 50% duty cycle
Key Frequency 2 mHz to 1 MHz

PWM

Carrier Waveform Pulse
Source Internal/External
Modulating Waveform Sine, Square, Ramp, Noise, Arb
Width Deviation 0% to 100% of the pulse width
Modulating Frequency 2 mHz to 1 MHz

External Modulation Input

Input Range 75 mVRMS to ±5 Vac + dc
Input Bandwidth 50 kHz
Input Impedance 10KΩ

Burst Characteristics
Carrier Waveform Sine, Square, Ramp, Pulse, Noise, Arb (except DC)
Carrier Frequency 2mHz to 25MHz 2mHz to 30MHz 2 mHz to 60 MHz
Burst Count 1 to 1,000,000 or Innite
Start/Stop Phase 0° to 360°, 0.1° resolution
Internal Period 1 μs to 500 s
Gated Source External Trigger
Trigger Source Internal, External or Manual
Trigger Delay 0 ns to 100 s

Sweep Characteristics
Carrier Waveform Sine, Square, Ramp, Arb (except DC)
Type Linear, Log or Step
Direction Up or Down
Start/Stop Frequency The same with the upper/lower limit of the corresponding carrier frequency
Sweep Time 1 ms to 500 s
Hold/Return Time 0 ms to 500 s
Trigger Source Internal, External or Manual
Marker Falling edge of the sync signal (programmable)

Frequency Counter
Function Frequency, Period, Positive/Negative Pulse Width, Duty Cycle
Frequency Resolution 7 digits/second (Gate Time = 1s)
Frequency Range 1 μHz to 200 MHz
Period Measurement Measurement Range 5ns to 16 days
Voltage Range and Sensitivity (non-modulating signal)

DC Offset Range ±1.5 Vdc

DC Coupling

AC Coupling

Pulse Width and Duty Cycle Measurement
Frequency and Amplitude

Ranges

Pulse Width

Duty Cycle Measurement Range (display) 0% to 100%
Input Characteristics
Input Signal Range Breakdown Voltage ±7Vac+dc Input Impedance = 1 MΩ

Input Adjustment

Input Trigger

Gate Time

1μHz to 100 MHz 50 mVRMS to ±2.5 Vac + dc
100 MHz to 200 MHz 100 mVRMS to ±2.5 Vac + dc
1 μHz to 100 MHz 50 mVRMS to ±2.5 Vpp
100 MHz to 200 MHz 100 mVRMS to ±2.5 Vpp

1 μHz to 25 MHz 50 mVRMS to ±2.5 Vac + dc

Min Pulse Width ≥20 ns
Pulse Width Resolution 5 ns

Coupling Mode AC DC

High-frequency Rejection

Trigger Level Range -2.5V to +2.5V

Trigger Sensitivity Range

GateTime1 1.310ms
GateTime2 10.48ms
GateTime3 166.7ms
GateTime4 1.342s
GateTime5 10.73s
GataTime6 >10s

On: Input Bandwidth = 250 kHz;
Off: Input Bandwidth = 200 MHz

0% (about 140 mV hysteresis voltage) to 100% (about 2 mV
hysteresis voltage)

DC Coupling

5

RIGOL

Trigger Characteristics
Trigger Input
Level TTL-compatible
Slope Rising or falling (selectable)
Pulse Width >100ns

Latency

Trigger Output
Level TTL-compatible
Pulse Width > 60 ns (typical)
Maximum Frequency 1 MHz

Two-channel Characteristics - Phase Offset
Range 0° to 360°
Waveform Phase Resolution 0.03°

Reference Clock
External Reference Input
Lock Range 10 MHz ± 50 Hz
Level 250 mVpp to 5 Vpp
Lock Time < 2 s
Input Impedance (Typical) 1 kΩ, AC coupling
Internal Reference Output
Frequency 10 MHz ± 50 Hz
Level 3.3 Vpp
Input Impedance (Typical) 50 Ω, AC coupling

Sweep: <100 ns (typical)
Burst: <300 ns (typical)

Sync Output
Level TTL-compatible
Impedance 50 Ω, nominal value

Overvoltage Protection
Occurred when:

The instrument amplitude setting is greater than 2Vpp or the output offset is greater than |2VDC| and the input voltage is greater



than ±11.5 × (1 ± 5%)V (<10kHz).
The instrument amplitude setting is lower than or equal to 2Vpp or the output offset is lower than or equal to |2VDC| and the



input voltage is greater than ±3.5 × (1 ± 5%)V (<10kHz).

General Specications

Power Supply

Power Voltage 100 V to 240 V (45 Hz to 440 Hz)
Power Consumption Lower than 40 W
Fuse 250 V, T3.15 A

Display

Type 3.5-inch TFT LCD
Resolution 320 horizontal × RGB × 240 vertical resolution
Color 16 M color

Environment

Temperature Range

Cooling Method Fan cooling

Humidity Range

Altitude

Mechanical

Dimensions (W×H×D) 261.5 mm × 112 mm × 318.4 mm

Weight

Interfaces USB Host, USB Device, LAN
IP Protection IP2X
Calibration Interval 1 year recommended calibration interval

Operating: 0℃ to 50
Non-operating: -40℃ to 70

Lower than 30℃: ≤95% relative humidity
30℃to 40℃: ≤75% relative humidity
40℃ to 50℃: ≤45% relative humidity

Operating: below 3000 meters
Non-operating: below 15,000 meters

Without Package: 3.2 kg
With Package: 4.5 kg

℃

℃

6

RIGOL

Certication Information

EMC

Electrical Safety

Ordering Information

Model

Standard Accessories

Options

in line with EN61326-1:2006

IEC 61000-3-2:2000

±4.0kV (contact discharge)
±4.0kV (air discharge)

3 V/m (80 MHz to 1 GHz)

IEC 61000-4-3:2002

3 V/m (1.4 GHz to 2 GHz)
1 V/m (2.0 GHz to 2.7 GHz)

IEC 61000-4-4:2004 1 kV power lines

0.5kV (Phase to Neutral)

IEC 61000-4-5:2001

0.5kV (Phase to PE)
1 kV (Neutral to PE)

IEC 61000-4-6:2003 3V,0.15MHz-80MHz

Voltage dip:
0 % UT during half cycle

IEC 61000-4-11:2004

0 % UT during 1 cycle
70 % UT during 25 cycles
Short interruption:
0 % UT during 1 cycle

Electrical Safety in line with
USA:UL 61010-1:2012,
Canada: CAN/CSA-C22.2 No. 61010-1-2012
EN 61010-1:2010

Description Order Number
DG1022Z (25MHz, Dual-channel) DG1022Z
DG1032Z (30MHz, Dual-channel) DG1032Z
DG1062Z (60MHz, Dual-channel) DG1062Z
Power Cord ­USB Cable CB-USBA-USBB-FF-150
BNC Cable CB-BNC-BNC-MM-100
Quick Guide -

Resource CD (including User’s Guide and etc.) -

16Mpts Memory for Arb Arb16M-DG1000Z
Rack Mount Kit (for single instrument) RM-1-DG1000Z
Rack Mount Kit (for dual instruments) RM-2-DG1000Z
40dB Attenuator RA5040K
10W Power Amplier PA1011
USB-GPIB Converter USB-GPIB

HEADQUARTER

RIGOL

TECHNOLOGIES, INC.
No.156,Cai He Village,
Sha He Town,
Chang Ping District, Beijing,
102206 P.R.China
Tel:[phone]
Fax:[phone]
Electronic Measurement
Instrument service and support
email:[e-mail]

®

RIGOL

is the registered trademark of

EUROPE

RIGOL

TECHNOLOGIES GmbH
Lindbergh str. 4
82178 Puchheim
Germany
Tel: [phone]
Email: [e-mail]

RIGOL

Technologies, Inc. Product information in

NORTH AMERICA

RIGOL

USA INC.
10200 SW Allen Blvd, Suite C
Beaverton, OR 97005, USA
Toll free: 877-4-RIGOL-1

Ofce: 440-232-4488

Fax: [phone]
Email: [e-mail]

this document subject to update without notice. For the latest information about
products, applications and services, please contact local

ofcial website:

www.rigol.com

RIGOL

ofce or access

TECHNOLOGIES,

RIGOL

's

RIGOL

JAPAN

RIGOL

TECHNOLOGIES JAPAN G.K.
MJ BLDG.3F,1-7-4 MINATO,CHUOU­KU,TOKYO,JAPAN 〒104-0043
Tel: [phone]
Fax: [phone]
Email: [e-mail]

Oct.2016