Page 1
K&A Manufacturing
6703 Zinser Street
Schofield, WI 54476
Phone: 800.298.4351
Fax: 866.882.9475
www.raproducts.com
Version Dated:10/31/18
HSTVMT Monitor/TV Hover
Mount Assembly Instructions
Read all the instructions before beginning.
Instruction # 53578 Hardware Pack # 53577
Page1 OF 4
Page 2
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: 800.298.4351
Fax: 866.882.9475
www.raproducts.com
3 4
Tools Required for Assembly:
Power Driver W/Adjustable Torque
5/32" Hex Head Driver Bit or
Allen Wrench
10mm Wrench or Socket
ITEM # PART # DESCRIPTION QTY.
1 801507 Monitor/TV Hover Mounting Plate 1
2 801508 Monitor/TV Hover Side Wing 2
3 52721 M6-1.0x8mm Truss Head Machine Screw 8
4 53252 M6-1 Hex Jam Nut 3mm Thick 4
5 801510 Monitor/TV Hover Mount Pole Joint 1
6 52743 Hover 27.6" Pole 1
52721
53252
Hardware Pack# 53577
Is Drawn Actual Size
3
5
Step 1a
Step 1a: If you are mounting a small TV or monitor
with 100mm or 200mm distance between the
mounting holes, use Step 1a. This setup will not
use the side wings 2 . Attach the pole joint 5 to
the raised side of the mounting plate 1 using
(4) machine screws 3 . Fully tighten.
Step 1b: If you are mounting a large TV or monitor
with greater than 200mm distance between the
mounting holes, use Step 1b. This setup will use the
side wings 2 . Attach the pole joint 5 to the recessed
side of the mounting plate 1 using (4) machine
1
screws 3 . Fully tighten
3
Step 1b
Instruction # 53578
5
1
Page 2 OF 4
Page 3
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: 800.298.4351
Fax: 866.882.9475
www.raproducts.com
1
Step 2: Do this step only if you have a large
TV or monitor with greater than 200mm between
the mounting holes. Insert (4) machine
screws 3 through the holes in the narrow
flange of the side wings 2 and the outermost
holes in the mounting plate 1 . Thread (4)
2
nuts 4 onto the screws and fully tighten.
Step 3a: Place your monitor on a protected
surface face down. Attach the mounting plate
4
assembly to your monitor or small TV using (4)
machine screws (not included) through the
inner holes that are 100mm apart in the
mounting plate 1 . Fully tighten.
Step 2
Step 3b: Place your TV or large monitor on a
3
protected surface face down. Attach the side
wings 2 to the back of your TV or large monitor
using either the holes that are 200mm or
400mm apart. Use (4) machine screws (not
included). Fully tighten.
1
2
1
Step 3b
Instruction # 53578
Step 3a
Page 3 OF 4
Page 4
K&A Manufacturing
6703 Zinser Street Schofield, WI 54476
Phone: 800.298.4351
Fax: 866.882.9475
www.raproducts.com
Step 4: Attach the pole 6 to the worksurface using
the instructions that came with it.
Step 5: With the help of an assistant, place the
mounting assembly's pole joint 5 onto the pole 6 .
Set it at the height desired and tighten the clamp
on the pole joint. This step is the same whether
or not the side wings 2 are used.
5
2
Instruction # 53578
6
Page 4 OF 4
Loading...