RIGHT ANGLE NEWHEIGHTS Series 4 XT, 53209 Assembly & Operation Instructions

NewHeights™ Series 4 XT
Elegante 3-Leg Workstation

Assembly/Operation Instructions

K&A Manufacturing
6703 Zinser Street
Schofield, WI 54476
Phone: [phone]
Fax: [phone]
www.raproducts.com
Version Dated 8/4/16

Failure to comply with or observe all assembly, safety, and operation
instructions and warnings regarding the use of this product may result
in serious property damage or bodily injury.

Make sure no obstacles are in the desk's path and all cords are of appropriate
length for the desk. Always maintain a 1" clearance around the table to prevent
pinching.

Never assemble (or disassemble) the table or components with the table plugged
into a power outlet. This product is for use on a nominal 120-volt circuit and has
a grounding plug. Make sure that the product is connected to an outlet having the
same configuration as the plug. No adapter should be used with this product.

Duty Cycle: 2 minutes ON/18 minutes OFF
Workstation can continuously operate for a maximum duration of two minutes.
After two minutes of non-stop operation, the workstation will automatically stop
and require eighteen minutes of cool down.

Read all the instructions before beginning.

Page1 OF 9Instruction # 53210 Hardware Pack # 53209

K&A Manufacturing

6703 Zinser Street Schofield, WI 54476

Phone: [phone]

Fax: [phone]

www.raproducts.com

Your workstation will have either (2) left legs (Leg A) and (1) right leg (Leg B) or
(2) right legs (Leg B) and (1) left leg (Leg A). The drawing below shows how to
distinguish the left leg A from the right leg B.

Leg A

Leg B

Left Return

Leg A

Leg A

Note: Motor box
faces inside of
table

Note: Motor box
faces inside of
table

4

Leg B

Leg B

Right Return

4

Front

Leg A Left Leg

Instruction # 53210

Front

Leg B Right Leg

Page 2 OF 9

K&A Manufacturing

6703 Zinser Street Schofield, WI 54476

Phone: [phone]

Fax: [phone]

www.raproducts.com

Tools Required for Assembly:

Power Driver W/Adjustable Torque
#2 Phillips Head Driver Bit
#2 Square Head Driver Bit
3/16" Hex Head Driver Bit or
Allen Wrench
Level

51708

53174

3

8

53638

52604

6

12

53176

50072

7

10

Instruction # 53210

Hardware Pack # 53209

Hardware is Drawn Actual Size

Page 3 OF 9

K&A Manufacturing

6703 Zinser Street Schofield, WI 54476

Phone: [phone]

Fax: [phone]

www.raproducts.com

All Screws

These Steps

3

Steps 1 & 2

Step 1: With the help of an assistant, lay the work-

surface(s) 1 on a protected surface with the pilot holes
facing up. If your worksurface has a seam, lay the
joiner plate 2 centered on the seam and about 3"
from the front. Attach it with (8) wood screws 3 .
No pilot holes are provided. Do not over-tighten the
screws. Use a low torque setting on the power driver.

Step 2: Place all (3) leg assemblies 4 on the
worksurface aligning the holes in the worksurface
supports with the pilot holes in the worksurface

4

1 . See page 2 to determine the locations of Leg A
and Leg B. The motor boxes must face the inside
of the workstation. Do not allow the leg assemblies
to stand without support. They can tip over and the

gear housing could crack. Be
careful to not pinch the wires
between the motor boxes and
the worksurface 1 . The

1

grommets on the motor wires
should be in the square notches
on the back of the motor boxes.

3

See Detail A. Attach the leg
assemblies to the worksurface
with (6) wood screws 3 in
each. Leave the screws loose
by about 1/8". You need to

2

adjust the legs when installing
the wire management channel.

ITEM # PART # DESCRIPTION QTY.

1 Varies Worksurface Varies
2 800352 3x5 Worksurface Joiner Plate 1

3 51708 M5 x 18mm (7/8") Sq/Ph/Wshr Head Wood Screw 49
4 Varies NewHeights Series 4 XT Leg Assembly 3
5 Varies NewHeights Series 4 XT Wire Management Channel 2
6 53638 5/16-18 x 3/8 Button Head Socket Screw 6

7 53176 .25x.696x.58 Flat Washer 4
8 53174 1/4-20x1/2 Phillips Pan Head Machine Screw 4

9 53225 TouchDown Hand Switch 1

10 50072 8 x 3/4 Pan Head Recex Drive Screw 4
11 50286 NewHeights Control Box 1

12 52604 3/16" Cable Clamp 4
13 PSSM-4-2 Power Strip 4 Recps 2 USB Chargers 10 Ft Cord 1

Instruction # 53210

Back of

Motor Box

Detail A

Page 4 OF 9

6703 Zinser Street Schofield, WI 54476

K&A Manufacturing

Phone: [phone]

Fax: [phone]

www.raproducts.com

Step 3: Your workstation may have two different
sizes of wire management channel 5 . Determine
the correct locations of the channels according to
the length and width of the worksurface(s). Slide
apart the channel until the holes near the ends of
it align with the holes in the motor boxes on the
desk side of the workstation. Place the flat side of
the channel against the motor boxes. Insert (4)
socket screws 6 through the holes near the ends of
the channel and thread them into the weld nuts inside
the motor boxes. See Detail B. Fully tighten. Fully
tighten the wood screws 3 holding the desk side leg
assemblies to the worksurface 1 . Attach the channel
to the worksurface with (5-10) wood screws 3 through
the front flange of the channel. Fully tighten. Keep
the wood screws at the end of the slots.

5

6

Detail B

3

B

Instruction # 53210

Step 3

Page 5 OF 9

K&A Manufacturing

6703 Zinser Street Schofield, WI 54476

Phone: [phone]

Fax: [phone]

www.raproducts.com

Step 4: Attach the other wire management channel 5
to the third leg 4 on the return side of the table. See
Detail B on Page 5. Fully tighten all of the screws.
Fully tighten the(6) wood screws 3 attaching the third
leg to the worksurface 1 . Attach the wire management
channel to the worksurface with (4-10) wood screws 3 .

Step 5: Place (2) black flat washers 7 on (2) black
machine screws 8 . Insert these through the slots in
one of the outer wire management sections and thread
them into the cage nuts pre-installed near the end of the
inner wire management section. See Detail C. Use any
(2) cage nuts that are accessible. Fully tighten. Repeat
Step 5 with the remaining wire management channel.

Cage Nuts Pre-

installed in Inner

Wire Management

Channel

7

8

Detail C

Instruction # 53210

C

Steps 4 & 5

Page 6 OF 9

Step 6: Align the holes in the control box 11 with the
pilot holes in the worksurface 1 . Attach it with (2)

6703 Zinser Street Schofield, WI 54476

Phone: [phone]

Fax: [phone]

www.raproducts.com

K&A Manufacturing

recex screws 10 . Align the holes in the switch 9 with
the pilot holes in the worksurface. Attach it with (2)
recex drive screws 10 . The switch and control box
can be installed anywhere on the worksurface, wire

lengths permitting. Capture the switch wire in the cable clamp 12 and attach it in the
location shown with (1) wood screw 3 . No pilot hole is provided.

Step 7: Attach the power strip 13 at the suggested location shown. It can be installed
anywhere. Attach it with the screws that came with the power strip.

13

Steps 6 & 7

Instruction # 53210

10

11

3

10

9

12

Page 7 OF 9

K&A Manufacturing

6703 Zinser Street Schofield, WI 54476

Phone: [phone]

Fax: [phone]

www.raproducts.com

HS

M1 M2 M3

Hand

Switch

Left

Hand

Center

Column

Column

Column

11

Right
Hand

Step 8: Run the wires as shown in the wire runs diagram
below. Run the wires in the wire management channels

5. Plug the wire from the switch into the receptacle
labeled HS on the control box 11 . Plug the motor wires
into the cables and plug the other ends of the cables into
into the receptacles labeled M1, M2, and M3 as shown in
the wiring diagram at left. Place the excess cable inside
the channels.

Step 9: If your workstation will get an optional cross
support(s), plug the unit into a standard 110 volt
receptacle. Push the down arrow until the worksurface
reaches its lowest point and clicks. Push the up arrow
and raise the legs about 12". Install the cross support(s)
using the supplemental instructions that came with the
cross support package(s). Return the legs to the lowest
position and unplug the power.

Step 10: With the help of an assistant, set the work­station upright in its final location. Level the unit if
required by turning the leveling glides clockwise
(from the top) on the low corners of the workstation.
If your workstation has casters, level it by turning
the bolts at the top of the casters.

Leveling Glide

Switch
Wire

Motor
Wire

Power
Cord
Power
Strip

Power
Cord
Control
Box

Instruction # 53210

Motor
Wire

Motor
Wire

Page 8 OF 9

K&A Manufacturing

6703 Zinser Street Schofield, WI 54476

Phone: [phone]

Fax: [phone]

www.raproducts.com

Operation and Reset Procedure

Plug the power cord into a standard 110v receptacle. A power surge protector is
recommended. Press the down arrow button until the worksurface reaches its lowest
position and clicks. The NewHeights™ workstation is ready for use. If you unplug or
lose power and the unit does not operate, follow the reset procedure below.

Reset Procedure: Unplug the power for 30 seconds and plug back in. Hold the down
arrow button until the unit stops at the bottom. Release the button; then hold the down
arrow button until the unit clicks twice.

Troubleshooting: If you are having any problems with the table operation, contact
RightAngle™ service at 800-298-4351 or [e-mail].

Warranty Information: NewHeights™ products are warranted to be free of defects
due to manufacturing or materials as follows: Three years on the gear and/or motor(s)
including the control box and switch. Five years on the support brackets, aluminum
columns and feet. We will replace any defective part after inspection by an
authorized agent. Costs incurred due to product replacement such as installation
labor or transportation are not covered by this warranty. When corresponding with
RightAngle™ products, record and provide the model and serial numbers located
on the control box.

Instruction # 53210

Page 9 OF 9