QuikFinder
™
Compact Reflex Sight
Attachment of QuikFinder to baseplate: Holding QuikFinder at 45
degree angle to baseplate, Insert long tab on front into long slot of
baseplate and rotate until catch on back of QuikFinder clips into small
slot on baseplate.
Removal of QuikFinder from baseplate: Holding baseplate, depress
button on clip on back of body and rot ate forward.
ON-OFF/Intensity: Rotary switch located on front of QuikFinder, just
below adjusting screws.
Pulse: Small white knob located on front of QuikFinder. Turn
clockwise to pulse.
Alignment: Turning the three white screws on the front of the unit shift
the reticule inside the view field to align the reticule with the telescope’s
field of view. Outer ring is 2°, inner ring is 1/2°.
Making sure it is working: (1) Go in a dimly lit room. Turn the small
white knob fully counter clockwise (2) Turn the black knob fully
clockwise (full brightness) (3) look at the bottom of the Quikfinder , do
you see a red glow coming around the battery holder? Then the LED is
lighting . (4) Now hold the Quikfinder up t o your eye with the knobs
pointing away from you. You should see 2 red rings.
Attachment to telescope: Cut and apply double sided adhesive foam
tape to rails on baseplate for adhesive mounting to telescope.
Alternative Mounting Methods: Hole on baseplate can be used for
screw mounting to telescope. For small scopes, single sided adhesive
foam tape can be applied to rails on baseplate and cable ties (available
at electronic and hardware stores) used to attach baseplate to
telescope.
Battery Installation: Uses one BR2032 or CR2032 3v lithium battery or
equivalent. Available at Radio Shack, photo stores, drug stores photo
departments and electronics stores. If you can't find a BR2032 or
CR2032, a BR2025 or CR2025 will also work. Remove QuikFinder
from base. Pop battery out of battery holder and install new battery,
minding polarity. Reattach QuikFinder to base.
Care:. Do not let sunlight shine directly into the lens — it will melt the
reticule. Treate lens and view field as you would any optical element of
your telescope, clean with soft cloth only.
Ordering Additional Baseplates: Additional baseplates are $7 each.
Please specify diameter of telescope tube when ordering. Shipping is
$4.85
5 Year limited warranty: Rigel Systems, 26850 Basswood Ave,
Rancho Palos Verdes CA, 90275 warrants to the original consumer
purchaser of its product that the product will be free of defects in
material or workmanship 5 years from the date of purchase under
normal use. During this warranty per iod, Rigel Systems will, at its
option, repair or replace the product without charge for parts or labor
when delivered to Rigel Systems with proof of the date of purchase
and a statement of the problem with the product. Shipping and handling
charges to Rigel Systems are your responsibility. This warranty does
not apply if the product has been altered or repaired by anyone other
than Rigel Systems or has been subjected to purchaser abuse,
accident, negligence or damag e subsequent to purchase including
battery damage to product. This warranty excludes incidental or
consequential damages resulting from the product or use of the product.
The product is not a toy. Keep away from children.
QuikFinder
™
Compact Reflex Sight
Attachment of QuikFinder to baseplate: Holding QuikFinder at 45
degree angle to baseplate, Insert long tab on front into long slot of
baseplate and rotate until catch on back of QuikFinder clips into small
slot on baseplate.
Removal of QuikFinder from baseplate: Holding baseplate, depress
button on clip on back of body and rot ate forward.
ON-OFF/Intensity: Rotary switch located on front of QuikFinder, just
below adjusting screws.
Pulse: Small white knob located on front of QuikFinder. Turn
clockwise to pulse.
Alignment: Turning the three white screws on the front of the unit shift
the reticule inside the view field to align the reticule with the telescope’s
field of view. Outer ring is 2°, inner ring is 1/2°.
Making sure it is working: (1) Go in a dimly lit room. Turn the small
white knob fully counter clockwise (2) Turn the black knob fully
clockwise (full brightness) (3) look at the bottom of the Quikfinder , do
you see a red glow coming around the battery holder? Then the LED is
lighting . (4) Now hold the Quikfinder up t o your eye with the knobs
pointing away from you. You should see 2 red rings.
Attachment to telescope: Cut and apply double sided adhesive foam
tape to rails on baseplate for adhesive mounting to telescope.
Alternative Mounting Methods: Hole on baseplate can be used for
screw mounting to telescope. For small scopes, single sided adhesive
foam tape can be applied to rails on baseplate and cable ties (available
at electronic and hardware stores) used to attach baseplate to
telescope.
Battery Installation: Uses one BR2032 or CR2032 3v lithium battery or
equivalent. Available at Radio Shack, photo stores, drug stores photo
departments and electronics stores. If you can't find a BR2032 or
CR2032, a BR2025 or CR2025 will also work. Remove QuikFinder
from base. Pop battery out of battery holder and install new battery,
minding polarity. Reattach QuikFinder to base.
Care:. Do not let sunlight shine directly into the lens — it will melt the
reticule. Treate lens and view field as you would any optical element of
your telescope, clean with soft cloth only.
Ordering Additional Baseplates: Additional baseplates are $7 each.
Please specify diameter of telescope tube when ordering. Shipping is
$4.85
5 Year limited wa rranty: Rigel Systems, 26850 Basswood Ave,
Rancho Palos Verdes CA, 90275 warrants to the original consumer
purchaser of its product that the product will be free of defects in
material or workmanship 5 years from the date of purchase under
normal use. During this warranty period, Rigel Systems will, at its
option, repair or replace the product without charge for parts or labor
when delivered to Rigel Systems with proof of the date of purchase
and a statement of the problem with the product. Shipping and handling
charges to Rigel Systems are your responsibility. This warranty does
not apply if the product has been altered or repaired by anyone other
than Rigel Systems or has been subjected to purchaser abuse,
accident, negligence or damag e subsequent to purchase including
battery damage to product. This warranty excludes incidental or
consequential damages resulting from the product or use of the product.
The product is not a toy. Keep away from children.
QuikFinder
™
Compact Reflex Sight
Attachment of QuikFinder to baseplate: Holding QuikFinder at 45
degree angle to baseplate, Insert long tab on front into long slot of
baseplate and rotate until catch on back of QuikFinder clips into small
slot on baseplate.
Removal of QuikFinder from baseplate: Holding baseplate, depress
button on clip on back of body and rot ate forward.
ON-OFF/Intensity: Rotary switch located on front of QuikFinder, just
below adjusting screws.
Pulse: Small white knob located on front of QuikFinder. Turn
clockwise to pulse.
Alignment: Turning the three white screws on the front of the unit shift
the reticule inside the view field to align the reticule with the telescope’s
field of view. Outer ring is 2°, inner ring is 1/2°.
Making sure it is working: (1) Go in a dimly lit room. Turn the small
white knob fully counter clockwise (2) Turn the black knob fully
clockwise (full brightness) (3) look at the bottom of the Quikfinder , do
you see a red glow coming around the battery holder? Then the LED is
lighting . (4) Now hold the Quikfinder up t o your eye with the knobs
pointing away from you. You should see 2 red rings.
Attachment to telescope: Cut and apply double sided adhesive foam
tape to rails on baseplate for adhesive mounting to telescope.
Alternative Mounting Methods: Hole on baseplate can be used for
screw mounting to telescope. For small scopes, single sided adhesive
foam tape can be applied to rails on baseplate and cable ties (available
at electronic and hardware stores) used to attach baseplate to
telescope.
Battery Installation: Uses one BR2032 or CR2032 3v lithium battery or
equivalent. Available at Radio Shack, photo stores, drug stores photo
departments and electronics stores. If you can't find a BR2032 or
CR2032, a BR2025 or CR2025 will also work. Remove QuikFinder
from base. Pop battery out of battery holder and install new battery,
minding polarity. Reattach QuikFinder to base.
Care:. Do not let sunlight shine directly into the lens — it will melt the
reticule. Treate lens and view field as you would any optical element of
your telescope, clean with soft cloth only.
Ordering Additional Baseplates: Additional baseplates are $7 each.
Please specify diameter of telescope tube when ordering. Shipping is
$4.85
5 Year limited wa rranty: Rigel Systems, 26850 Basswood Ave,
Rancho Palos Verdes CA, 90275 warrants to the original consumer
purchaser of its product that the product will be free of defects in
material or workmanship 5 years from the date of purchase under
normal use. During this warranty period, Rigel Systems will, at its
option, repair or replace the product without charge for parts or labor
when delivered to Rigel Systems with proof of the date of purchase
and a statement of the problem with the product. Shipping and handling
charges to Rigel Systems are your responsibility. This warranty does
not apply if the product has been altered or repaired by anyone other
than Rigel Systems or has been subjected to purchaser abuse,
accident, negligence or damag e subsequent to purchase including
battery damage to product. This warranty excludes incidental or
consequential damages resulting from the product or use of the product.
The product is not a toy. Keep away from children.
Loading...