1
DVR
Hardware Manual
Ver. 2016-11
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is Subject to the following two conductions: (1)
The device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operations.
WARNING
Unauthorized reproduction of all or part of this manual is strictly prohibited.
The figures in this manual are for illustration purposes only (may differ from the actual product).
The specifications and design of the product are subject to change without prior notice for purposes of
quality improvement.
CAUTIONS
To get the best use out of the product, be sure to read the cautions before using the product. For safety,
please take note of the following.
Instructions before using the product
1. To prevent electric shock when installing, moving, or opening the DVR and peripheral devices, connect
and disconnect the cables as instructed. All cables must be connected to grounded power outlets.
2. If the product is installed near a power outlet, make sure it can be unplugged easily.
3. Do not use the DVR in water or in wet places.
4. Keep the plastic packing materials used for the DVR or other peripheral devices out of reach of children
(may cause suffocation).
Installation Environment of the product
1. Maintain the following conditions: operating temperature of 5˚C ~ 40˚C; operating humidity of 10% ~
80%.
2. Install the DVR in a safe place that is free from external vibration.
3. Install the DVR in a well-ventilated place.
4. To protect the hard disk from data loss and breakdown, install the DVR away from magnetic materials.
5. When using a rack other than the standard one, use a separate table with sufficient spacing, i.e., 60cm
from the floor, 50cm from the ceiling, and 20cm from the side and back walls and other objects.
Safety Notes on the Product
1. When installing additional boards and HDD, separate the power cable and turn OFF power supplied to
the DVR completely.
2. Keep the product away from heat-generating devices such as heaters.
3. Do not use a damaged power cord.
4. To prevent problems due to magnetic interference and electric surge, use only grounded cables and
power outlets.
5. If the power cord is connected, do not touch the power unit. If the power cord is connected, electric
current is still flowing internally even after the switch is turned OFF.
6. Do not place a heavy object on top of the product.
7. Do not drop a conductive object in the ventilation holes.
8. Allot sufficient space for system cabling.
9. Use only the parts indicated in the manual. Do not disassemble, repair, or modify the product without
permission.
10. Incorrect system setup may cause malfunction.
11. Shut down the system normally as instructed in the manual.
Safety Notes on the Lithium Battery
1. Replace lithium batteries as instructed to avoid danger.
2. Dispose used lithium batteries properly.
2
【Warning and Caution are indicated as follows.】
Possible injury or product damage.
Risk of minor injury or product damage.
Cautions for the usage of the product.
Information for the usage of the product.
3
Table of contents
Chapter 1. Introduction ............................................................... 4
１-１ Definition of maunal terms.............................................................................................................. 4
１-２ Major Features ....................................................................................................................................... 4
１-２-１ Kute Major Features ................................................................................. 4
１-２-２ Kute Components .................................................................................... 5
１-２-３ Kute EX-SDI Major Features ...................................................................... 6
１-２-４ Kute EX-SDI Components ......................................................................... 7
１-２-５ Lite Major Features .................................................................................. 8
１-２-６ Lite Components ..................................................................................... 9
１-２-７ Lite EX-SDI Major Features....................................................................... 10
１-２-８ Lite EX-SDI Components .......................................................................... 11
１-２-９ Blue Major Features ................................................................................ 12
１-２-１０ Blue Components ................................................................................ 13
１-２-１１ Deluxe Major Features .......................................................................... 14
１-２-１２ Deluxe Components ............................................................................. 15
Chapter 2. Installation and Connection ......................................... 16
2-１ Names and Features of Each Parts ............................................................................................. 16
2-１-１ Kute Installation and Connection .................................................................. 16
2-１-２ Kute EX-SDI Installation and Connection ....................................................... 17
2-１-３ Lite Installation and Connection ................................................................... 20
2-１-４ Lite EX-SDI Installation and Connection ........................................................ 23
2-１-５ Blue Installation and Connection .................................................................. 26
2-１-６ Deluxe Installation and Connection............................................................... 27
Chapter 3. Operation and Setup .................................................. 30
3-１ Kute series front panel...................................................................................................................... 30
3-２ Lite series front panel........................................................................................................................ 31
3-３ Blue series front panel ...................................................................................................................... 32
3-４ Deluxe series front panel ................................................................................................................. 33
3-５ Remote controller ............................................................................................................................... 34
3-５-１ Remote controller A-Type ...................................................................... 34
3-５-２ Remote controller B-type ....................................................................... 36
3-６ Mouse ....................................................................................................................................................... 36
3-７ Jog/Shuttle.............................................................................................................................................. 37
Chapter 4. DVR HDD Installation ................................................. 38
4-１ Kute series HDD installation .......................................................................................................... 38
4-２ Lite series HDD installation............................................................................................................. 39
4-３ Blue series HDD installation ........................................................................................................... 40
4-４ Deluxe series HDD installation ...................................................................................................... 41
A/P/P/E/N/D/I/X ....................................................................... 43
Recommended PTZ Camera Protocol ........................................... 43
4
Chapter 1. Introduction
１-１Definition of maunal terms
Kute
DVR with 1 HDD Bay (Max 4TB supported)
Lite
DVR with 2 HDD Bays (Max 8TB per HDD supported)
Blue
DVR with 3 HDD Bays (Max 6TB per HDD supported)
Deluxe
DVR with 6 HDD Bays (Max 8TB per HDD supported)
With PoE
Built in PoE (4PoE, 8PoE, 16PoE)
Non PoE
Without PoE
１-２Major Features
１-２-１Kute Major Features
Specifications
5brid DVR
(TVI, AVI, CVI,
960H, IPC)
3brid DVR
(TVI, AVI, 960H)
4 CH
8CH
4CH
System
OS
Embedded Linux
Control
Mouse, Remote controller, Network
Hexaplex
Realtime monitoring, Recording, Playback, Backup, Network, Setup
Upgrade
USB2.0 Memory(FAT 32) Network
Video
System
NTSC / PAL - Config switch
Video Input
4 BNC or 3 BNC+1 IPC
8 BNC
4 BNC
Video Output
1 HD-MI, 1 VGA, 1 BNC
Audio
Audio Input
1 RCA
Audio Output
HD-MI, RCA
Video
Recording
Compression
H.264
Recording Speed
1080p 15fps/ch / 720p, 960H real-time
Resolution
1080p, 720p, 960H, D1, 2CIF, CIF
Event
Motion, Sound Detecion
Recording Quality
5 Levels
Audio
Recording
Compression
G.711U
Audio Sampling Rate
8KHz
Network
Network Connection
Ethernet 10/100/1G
Compression
H.264 / JPEG
Speed
Max. 1080p 6fps
Resolution
Max. 1080p
Backup
Backup/Download
USB2.0, Network
Format
Video clip(rms, avi), JPEG still image, Log list, Setup data
5
１-２-２Kute Components
After unpacking the product, check whether following accessories are included.
- Mouse
- Quick Setup Guide
- CD (VMS, User manual)
- Power code: 12V 2A
- Remote Controller B-Type / AAA 1.5V batteries 2ea (Optional)
Alarm
Pre/Post-Alarm
5sec / 5sec~5min
Alarm Action
E-mail, Event Popup, Buzzer,
Remote CMS, Front LED
Display
HD-MI
FHD, XGA
VGA
FHD, XGA
TV
SDTV(720x480/576)
Mode
6/4/1/SEQ- LIVE,
6/4/1 –P.B.
8/4/1/SEQ- LIVE,
8/4/1 –P.B.
4/1/SEQ- LIVE,
4/1 –P.B.
External
Interface
PTZ
RS485 - Terminal Block
ATM / POS
N/A
Storage
Internal Device /
External Device
1 HDD
ODD
N/A
Feature
DDNS, DHCP, UPNP
Yes
VMS, RMS
Windows
Smartphone (3G/4G)
Android, iPhone, iPad
Mac Viewer
Apple Mac OS
General
Power Supply
12V/2A
Consumption
24 Watts
Dimension
260 x 45 x 240 mm
6
１-２-３Kute EX-SDI Major Features
Specifications
EX-SDI
(EX-SDI, HD-SDI, 960H)
8CH
4CH
System
OS
Embedded Linux
Control
Mouse, Remote controller, Network
Hexaplex
Realtime monitoring, Recording, Playback, Backup, Network, Setup
Upgrade
USB2.0 Memory(FAT 32) Network
Video
System
NTSC / PAL - Config switch
Video Input
8 BNC
4 BNC
Video Output
1 HD-MI, 1 VGA, 1 BNC
Audio
Audio Input
8 RCA
4 RCA
Audio Output
HD-MI, RCA
Video
Recording
Compression
H.264
Recording Speed
Max. 30 fps/ch
Resolution
1080p, 720p, 960H, D1, 2CIF, CIF
Event
Motion, Sound Detection
Recording Quality
5 Levels
Audio
Recording
Compression
G.711U
Audio Sampling Rate
8KHz
Network
Network Connection
Ethernet 10/100/1G
Compression
H.264 / JPEG
Speed
Max. 1080p 20fps
Resolution
Max. 1080p
Backup
Backup/Download
USB2.0, Network
Format
Video clip(rms, avi), JPEG still image, Log list, Setup data
Alarm
Pre/Post-Alarm
5sec / 5sec~5min
Alarm Action
E-mail, Event Popup, Buzzer,
Remote CMS, Front LED
Display
HD-MI
FHD, XGA
VGA
FHD, XGA
TV
SDTV(720x480/576)
Mode
8/4/1/SEQ- LIVE,
8/4/1 –P.B.
4/1/SEQ- LIVE,
4/1 –P.B.
External
Interface
PTZ
RS485 - Terminal Block
ATM / POS
N/A
Storage
Internal Device /
External Device
1 HDD
ODD
N/A
Feature
DDNS, DHCP, UPNP
Yes
7
１-２-４Kute EX -SDI Components
After unpacking the product, check whether following accessories are included.
- Mouse
- Quick Setup Guide
- CD (VMS, User manual)
- Power code: 12V 2A
- Remote Controller B-Type / AAA 1.5V batteries 2ea (Optional)
VMS, RMS
Windows
Smartphone (3G/4G)
Android, iPhone, iPad
Mac Viewer
Apple Mac OS
General
Power Supply
12V/2A
Consumption
24 Watts
Dimension
260 x 45 x 240 mm
8
１-２-５Lite Major Features
Line Up
5brid DVR
(TVI, AVI, CVI, 960H, IPC)
Channels
16CH
8CH
4CH
System
OS
Embedded Linux
Control
Mouse, Remote controller, Network
Hexaplex
Realtime monitoring, Recording, Playback, Backup, Network, Setup
Upgrade
USB2.0 Memory(FAT 32) Network
Video
Video Input
16 BNC, 8 IPC
8 BNC, 4 IPC
4 BNC, 2 IPC
Video Output
1 HD-MI, 1 VGA, 2 BNC(TVI,CVBS)
Audio
Audio Input
4 RCA
Audio Output
HD-MI, RCA
Video
Recording
Compression
H.264
Recording Speed
Max. 30 fps/ch
Resolution
Max. UHD(4K) / TVI, IP
Event
Motion, Sound Detection
Recording Quality
5 Levels
Audio
Recording
Compression
G.711U
Audio Sampling Rate
8KHz
Network
Network Connection
2 x Ethernet 10/100/1G
Compression
H.264 / JPEG
Speed
Max. 1080p 20fps
Resolution
Max. 1080p
Backup
Backup/Download
USB2.0, Network
Format
Video clip(rms, avi), JPEG still image, Log list, Setup data
Alarm
Pre/Post-Alarm
5sec / 5sec~5min
Alarm Action
E-mail, Event Popup, Buzzer, PTZ Preset
Relay, Spot, Remote CMS
Input/Output
4/1 – NC/NO
Display
HD-MI
UHD, FHD, SxGA, XGA
VGA
UHD, FHD, SxGA, XGA
Spot
HD spot, SD spot
Mode
24/16/8/4/1/SEQ- LIVE,
24/16/8/4/1 –P.B.
12/8/4/1/SEQ- LIVE,
12/8/4/1 –P.B.
6/4/1/SEQ- LIVE,
6/4/1 –P.B.
External
Interface
PTZ / Keyboard
2 RS485 - Terminal Block
ATM / POS
RS232C - Terminal Block / Ethernet POS
Storage
Internal Device /
External Device
2 HDD or 1HDD + 1 eSATA
ODD
N/A
9
１-２-６Lite Components
After unpacking the product, check whether following accessories are included.
- Mouse
- Quick Setup Guide
- CD (VMS, User manual)
- Power Adaptor/Code (4CH: 12V 3.3A, 8/16CH: 12V 5A)
- Screws for HDD installation
- Remote Controller A-Type / AAA 1.5V batteries 2ea (Optional)
Features
DDNS, DHCP, UPNP
Yes
VMS, RMS
Windows
Smartphone (3G/4G)
Android, iPhone, iPad
Mac Viewer
Apple Mac OS
General
Power Supply
12V/5A
12V/3.3A
12V/3.3A
Consumption
60 Watts
40 Watts
40 Watts
Dimension
340 x 60 x 300 mm
10
１-２-７Lite EX-SDI Major Features
Line Up
EX-SDI
(EX-SDI, HD-SDI, 960H)
Channels
16CH
8CH
4CH
System
OS
Embedded Linux
Control
Mouse, Remote controller, Network
Hexaplex
Realtime monitoring, Recording, Playback, Backup, Network, Setup
Upgrade
USB2.0 Memory(FAT 32) Network
Video
Video Input
16 BNC
8 BNC
4 BNC
Video Output
1 HD-MI, 1 VGA, 1 BNC
1 HD-MI, 1 VGA, 1 BNC,
1 RCA (SPOT)
1 HD-MI, 1 VGA, 1 BNC,
1 RCA (SPOT)
Audio
Audio Input
16 RCA
8 RCA
4 RCA
Audio Output
HD-MI, RCA
Video
Recording
Compression
H.264
Recording Speed
Max. 30 fps/ch
Resolution
Max. FHD
Event
Motion, Sound Detection
Recording Quality
5 Levels
Audio
Recording
Compression
G.711U
Audio Sampling Rate
8KHz
Network
Network Connection
Ethernet 10/100/1G
Compression
H.264 / JPEG
Speed
Max. 1080p 5fps
Resolution
Max. 1080p
Backup
Backup/Download
USB2.0, Network
Format
Video clip(rms, avi), JPEG still image, Log list, Setup data
Alarm
Pre/Post-Alarm
5sec / 5sec~5min
Alarm Action
E-mail, Event Popup, Buzzer, PTZ Preset
Relay, Spot, Remote CMS
Input/Output
4/1 – NC/NO
Display
HD-MI
FHD, SxGA, XGA
VGA
FHD, SxGA, XGA
Spot
SDTV(720x480)
Mode
16/8/4/1/SEQ- LIVE,
16/8/4/1 –P.B.
8/4/1/SEQ- LIVE,
8/4/1 –P.B.
4/1/SEQ- LIVE,
4/1 –P.B.
External
Interface
PTZ / Keyboard
2 RS485 - Terminal Block
ATM / POS
RS232C - Terminal Block / Ethernet POS
Storage
Internal Device /
External Device
2 HDD or 1HDD + 1 eSATA
ODD
N/A
Features
DDNS, DHCP, UPNP
Yes
VMS, RMS
Windows
Smartphone (3G/4G)
Android, iPhone, iPad
11
１-２-８Lite EX-SDI Components
After unpacking the product, check whether following accessories are included.
- Mouse
- Quick Setup Guide
- CD (VMS, User manual)
- Power Adaptor/Code (4/8CH: 12V 3.3A, 16CH: 12V 5A)
- Screws for HDD installation
- Remote Controller A-Type / AAA 1.5V batteries 2ea (Optional)
Mac Viewer
Apple Mac OS
General
Power Supply
12V/5A
12V/3.3A
12V/3.3A
Consumption
60 Watts
40 Watts
40 Watts
Dimension
340 x 60 x 300 mm
12
１-２-９Blue Major Features
Line Up
5brid DVR
(TVI, AVI, CVI, 960H, IPC)
Channels
16CH
8CH
4CH
System
OS
Embedded Linux
Control
Mouse, Remote controller, Network
Hexaplex
Realtime monitoring, Recording, Playback, Backup, Network, Setup
Upgrade
USB2.0 Memory(FAT 32) Network
Video
Video Input
16 BNC, 8 IPC
8 BNC, 4 IPC
4 BNC, 2 IPC
Video Output
1 HD-MI, 1 VGA, 2 BNC(TVI,CVBS)
Audio
Audio Input
4 RCA
8 RCA
16 RCA
Audio Output
HD-MI, RCA
Video
Recording
Compression
H.264
Recording Speed
Max. 30 fps/ch
Resolution
Max. UHD(4K) / TVI, IP
Event
Motion, Sound Detection
Recording Quality
5 Levels
Audio
Recording
Compression
G.711U
Audio Sampling Rate
8KHz
Network
Network Connection
2 x Ethernet 10/100/1G
Compression
H.264 / JPEG
Speed
Max. 1080p 20fps
Resolution
Max. 1080p
Backup
Backup/Download
USB2.0, Network
Format
Video clip(rms, avi), JPEG still image, Log list, Setup data
Alarm
Pre/Post-Alarm
5sec / 5sec~5min
Alarm Action
E-mail, Event Popup, Buzzer, PTZ Preset
Relay, Spot, Remote CMS, Front LED
Input/Output
4/1 – NC/NO
Display
HD-MI
UHD, FHD, SxGA, XGA
VGA
UHD, FHD, SxGA, XGA
Spot
HD spot, SD spot
Mode
24/16/8/4/1/SEQ- LIVE,
24/16/8/4/1 –P.B.
12/8/4/1/SEQ- LIVE,
12/8/4/1 –P.B.
6/4/1/SEQ- LIVE,
6/4/1 –P.B.
External
Interface
PTZ / Keyboard
2 RS485 - Terminal Block
ATM / POS
RS232C - Terminal Block / Ethernet POS
Storage
Internal Device /
External Device
3 HDD, 1 eSATA,
ODD
DVD R/W
Features
DDNS, DHCP, UPNP
Yes
VMS, RMS
Windows
Smartphone (3G/4G)
Android, iPhone, iPad
13
１-２-１０Blue Components
After unpacking the product, check whether following accessories are included.
- Mouse
- Quick Setup Guide
- CD (VMS, User manual)
- Power Adaptor (12V 5A)
- RACK Mount Handles
- Screws for HDD installation
- Remote Controller A-Type / AAA 1.5V batteries 2ea (Optional)
Mac Viewer
Apple Mac OS
General
Power Supply
12V/5A
Consumption
60 Watts
Dimension
430 x 86 x 270 mm
14
１-２-１１Deluxe Major Features
Line Up
5brid DVR
(TVI, AVI, CVI, 960H, IPC)
Channels
16CH
System
OS
Embedded Linux
Control
Mouse, Remote controller, Network
Hexaplex
Realtime monitoring, Recording, Playback, Backup, Network, Setup
Upgrade
USB2.0 Memory(FAT 32) Network
Video
Video Input
16 BNC, 8 IPC
Video Output
1 HD-MI, 1 VGA, 2 BNC(TVI,CVBS)
Audio
Audio Input
16 RCA
Audio Output
HD-MI, RCA
Video
Recording
Compression
H.264
Recording Speed
Max. 30 fps/ch
Resolution
Max. UHD(4K) / TVI, IP
Event
Motion, Sound Detection
Recording Quality
5 Levels
Audio
Recording
Compression
G.711U
Audio Sampling Rate
8KHz
Network
Network Connection
2 x Ethernet 10/100/1G
Compression
H.264 / JPEG
Speed
Max. 1080p 20fps
Resolution
Max. 1080p
Backup
Backup/Download
USB2.0, Network
Format
Video clip(rms, avi), JPEG still image, Log list, Setup data
Alarm
Pre/Post-Alarm
5sec / 5sec~5min
Alarm Action
E-mail, Event Popup, Buzzer, PTZ Preset
Relay, Spot, Remote CMS, Front LED
Input/Output
16/4 – NC/NO
Display
HD-MI
UHD, FHD, SxGA, XGA
VGA
UHD, FHD, SxGA, XGA
Spot
HD spot, SD spot
Mode
24/16/8/4/1/SEQ- LIVE, 24/16/8/4/1 –P.B.
External
Interface
PTZ / Keyboard
2 RS485 - Terminal Block
ATM / POS
RS232C - Terminal Block / Ethernet POS
Storage
Internal Device /
External Device
6 HDD, 2 eSATA,
ODD
DVD R/W
Features
DDNS, DHCP, UPNP
Yes
VMS, RMS
Windows
Smartphone (3G/4G)
Android, iPhone, iPad
Mac Viewer
Apple Mac OS
15
１-２-１２Deluxe Components
After unpacking the product, check whether following accessories are included.
- Mouse
- Quick Setup Guide
- CD (VMS, User manual)
- Power Code
- RACK Mount Handles
- Screws for HDD installation
- Remote Controller A-Type / AAA 1.5V batteries 2ea (Optional)
General
Power Supply
AC 100 ~ 250V, 50/60Hz
Consumption
80 Watts
Dimension
440 x 88 x 430 mm
16
Chapter 2. Installation and Connection
2-１ Names and Features of Each Parts
2-１-１Kute Installation and Connection
[Figure 1 Kute 4/8CH 1-１-１Kute Installation and Connection]
No.
Name
Features
Device can be
connected
Type
1
CAMERA IN
Video camera connection
CCTV camera
BNC
2
AUDIO OUT
Audio outpput (Line-out)
Speaker
RCA
3
AUDIO IN
Audio input
Mic
RCA
4
TV
CCTV monitor connection
CCTV Monitor
BNC
5
VGA-OUT
VGA Monitor or LCD Monitor
VGA Monitor
D-SUB 15P
6
HD-MI
HD-MI output
HD-MI Monitor
HD-MI
7
Ethernet
Ethernet 10/100/1G Base-T
LAN cable
RJ-45
8
USB
USB 2.0
USB Mouse, Memory
USB Type-A
9
Terminal Block
RS-485
PTZ Camera
Terminal Block
10
CONFIG
NTSC/PAL
FHD / XGA
DIP S/W, 2-pin
11
Power
DC 12V
Power Adapter
DC Jack
17
Config Switch Setting
Switch 1
Switch 2
Terminal Block
[Figure 2 Kute Series Terminal Block]
This is Termnial block located at the rear side to connect PTZ (RS-485) camera.
Kute series supports one PTZ control.
① PTZ Camera connection
TRX+/TRX- calbes from PTZ cameras can be input to the Termnial block No. 1&2. You can see the compatibility
list of PTZ camera from APPENDIX of this manual.
2-１-２Kute EX-SDI Installation and Connection
[Figure 3 Kute EX-SDI 4CH Installation and Connection]
18
[Figure 4 Kute EX-SDI 8CH Installation and Connection]
No.
Name
Features
Device can be
connected
Type
1
TV
CCTV monitor connection
CCTV Monitor
BNC or RCA
2
CAMERA IN
Video camera connection
CCTV Camera
BNC
3
AUDIO IN
Audio input
Mic
RCA
4
AUDIO OUT
Audio output (Line-out)
Speaker
RCA
5
VGA-OUT
VGA monitor or LCD monitor connection
VGA Monitor
D-SUB 15P
6
HD-MI
HD-MI output
HD-MI Monitor
HD-MI
7
Terminal Block1
SENSOR IN / RELAY OUT
Terminal Block
8
Ethernet
Ethernet 10/100/1G Base-T
LAN Cable
RJ-45
9
USB
USB 2.0
USB Mouse, Memory
USB Type-A
10
Terminal Block2
RS-485
PTZ Camera
Terminal Block
11
CONFIG
NTSC/PAL
FHD / XGA
DIP S/W, 2-pin
12
Power
DC 12V
Power Adapter
DC Jack
19
Config Switch Setting
Switch 1
Switch 2
Terminal Block
[Figure 5 Kute Series TB1 Description]
[Figure 6 Kute Series TB2 Description]
This is Terminal Block loatced at the rear to control PTZ, Sensor and Relay features.
① PTZ Camera connection
TRX+/TRX- calbes from PTZ cameras can be input to the TRX+ and TRX-. You can see the compatibility list of
PTZ camera from APPENDIX of this manual.
② Sensor / Relay / POS
A. Sensor connection
I. Sensors can be input to the Terminal Block S1 ~S16.
II. It can be connected regardless of channel numbers.
B. Relay connection
I. Relay can be input to the Terminal Block R1~R4.
II. Relay can be connected to the Alarm action devices like Siren or Light bar.
Please note that relay might be not working depending on the types. In this
case, power supply has to be connected to the relay.
Sensor and Relay type
NC(Normal Close): Normal close and Event open
NO(Normal Open): Normal open and Event close
20
2-１-３Lite Installation and Connection
[Figure 7 Lite 4/8CH 1-１-１Installation and Connection]
[Figure 8 Lite 16CH 1-１-１Installation and Connection]
No.
Name
Features
Device can be
connected
Type
1
AUDIO OUT
Audio output (Line-out)
Speaker
RCA
2
AUDIO IN
Audio input (4CH)
Mic
RCA
3
CAMERA IN
Video camera connection
CCTV Camera
BNC
4
e-SATA
External SATA
e-SATA
e-SATA
5
FHD SPOT
SD SPOT
FHD SPOT(TVI interface)
SD SPOT(CVBS interface)
TVI input device
CVBS input device
BNC
6
ETHERNET
Ethernet 10/100/1G Base-T
UP : CLIENT S/W
DOWN : IP CAMERA
LAN cable
IP CAMERA
RJ-45
7
VGA-OUT
VGA monitor or LCD monitor connection
VGA monitor
D-SUB 15P
8
HD-MI
HD-MI output
HD-MI monitor
HD-MI
9
Terminal Block
RS-485 / SENSOR IN / RELAY OUT / POS
PTZ camera
Terminal Block
10
CONFIG
RESOLUTION setting UHD/FHD/XGA/SXGA
DIP S/W, 2-pin
11
Power
DC 12V
Power Adapter
DC Jack
21
Config Switch Setting
Switch 1
Switch 2
RESOLUTION
UP
UP
FHD
UP
DOWN
XGA
DOWN
UP
SXGA
DOWN
DOWN
UHD
Terminal Block
[Figure 9 Lite Series Terminal Block Description]
This is Terminal Block loatced at the rear to control PTZ, Sensor, Relay and POS features
① PTZ camera/ Keyboard Controller
PTZ cameras can be input to the Termnial block No. 4&5&6(GND). You can see the compatibility list of PTZ
camera from APPENDIX of this manual.
Keyboard Controller can be connected to the Terminal block No. 2&3.
PTZ might be not working perfectly if there is no connection for GND
② Sensor / Relay / POS
Sensor and Relay type
NC(Normal Close): Normal close and Event open
NO(Normal Open): Normal open and Event close
22
A. Sensor connection
I. Sensors can be input to the Terminal Block S1 ~S4.
II. It can be connected regardless of channel numbers.
B. Relay connection
I. Relay can be input to the Terminal Block R1.
II. Relay can be connected to the Alarm action devices like Siren or Light bar.
C. POS connection
I. POS (RS-232c) can be input the Terminal Block No. 1
Please note that relay might be not working depending on the types. In this
case, power supply has to be connected to the relay.
NTSC/PAL Setting
Open the top case of DVR then change the setting with “2pin Jumper” on the board.
NTSC / PAL SELECT Direction :
JP2
The way of setting
JUMPER OPEN : NTSC
JUMPER SHORT : PAL
Please don’t change this setting without any reason as we provide the products
with correct setting normally.
23
2-１-４Lite EX-SDI Installation and Connection
[Figure 10 Lite EX-SDI 4CH Installation and Connection]
[Figure 11 Lite EX-SDI 8CH Installation and Connection]
[Figure 12 Lite EX-SDI 16CH Installation and Connection]
24
No.
Name
Features
Device can be
conneted
Type
1
AUDIO OUT
Audio output (Line-out)
Speaker
RCA
2
AUDIO IN
Audio input (4CH)
Mic
RCA
3
CAMERA IN
Video camera connection
CCTV Camera
BNC
4
e-SATA
External SATA
e-SATA
e-SATA
5
TV
CCTV monitor connection
CCTV Monitor
BNC
6
HD-MI
HD-MI output
HD-MI Monitor
HD-MI
7
VGA-OUT
VGA or LCD Monitor
VGA Monitor
D-SUB 15P
8
HD-MI
HD-MI output
HD-MI Monitor
HD-MI
8
ETHERNET
Ethernet 10/100/1G Base-T
LAN Cable
RJ-45
9
Terminal Block
RS-485 / SENSOR IN / RELAY OUT / POS
PTZ Camera
Terminal Block
10
CONFIG
RESOLUTION setting UHD/FHD/XGA/SXGA
DIP S/W, 2-pin
11
Power
DC 12V
Power Adapter
DC Jack
12
SPOT
Video output of the event signal channel
CCTV Monitor
RCA
Config Switch Setting
Switch 1
Switch 2
Terminal Block
[Figure 13 Lite Series Terminal Block Description]
This is Terminal Block loatced at the rear to control PTZ, Sensor, Relay and POS features.
① PTZ camera/ Keyboard Controller
A. PTZ cameras can be input to the Termnial block No. 4&5&6(GND). You can see the compatibility
list of PTZ camera from APPENDIX of this manual.
B. Keyboard Controller can be connected to the Terminal block No. 2&3.
25
PTZ might be not working perfectly if there is no connection for GND
② Sensor / Relay / POS
A. Sensor connection
I. Sensors can be input to the Terminal Block S1 ~S4.
II. It can be connected regardless of channel numbers.
B. Relay connection
I. Relay can be input to the Terminal Block R1.
II. Relay can be connected to the Alarm action devices like Siren or Light bar.
C. POS connection
II. POS (RS-232c) can be input the Terminal Block No. 1
Please note that relay might be not working depending on the types. In this
case, power supply has to be connected to the relay.
Sensor and Relay type
NC(Normal Close): Normal close and Event open
NO(Normal Open): Normal open and Event close
26
2-１-５Blue Installation and Connection
To be updated soon.
27
2-１-６Deluxe Installation and Connection
[Figure 14 Deluxe 16CH Installation and Connection]
No.
Name
Features
Device can be
conneted
Type
1
AUDIO OUT
Audio output (Line-out)
Speaker
RCA
2
AUDIO IN
Audio input (16CH)
Mic
RCA
3
CAMERA IN
Video camera
CCTV Camera
BNC
4
e-SATA
External SATA
e-SATA
e-SATA
5
HD SPOT
TVI video output (SD/HD)
TVI Input Device
BNC
6
ETHERNET
Ethernet 10/100/1G Base-T
UP : CLIENT S/W
DOWN : IP CAMERA
LAN cable
IP CAMERA
RJ-45
7
VGA-OUT
VGA or LCD Monitor
VGA Monitor
D-SUB 15P
8
HD-MI
HD-MI Output
HD-MI Monitor
HD-MI
9
Terminal Block
RS-485 / SENSOR IN / RELAY OUT / POS
PTZ Camera
Terminal Block
10
CONFIG
RESOLUTION Setting UHD/FHD/XGA/SXGA
DIP S/W, 2-pin
11
Power
Power Cord Connection
Power Cord
AC Power socket
28
Config Switch Setting
Switch 1
Switch 2
RESOLUTION
UP
UP
FHD
UP
DOWN
XGA
DOWN
UP
SXGA
DOWN
DOWN
UHD
Terminal Block
[Figure 15 Deluxe Series TB1 Terminal Block Description]
[Figure 16 Deluxe Series TB2 Terminal Block Description]
This is Terminal Block loatced at the rear to control PTZ, Sensor, Relay and POS features.
① PTZ camera/ Keyboard Controller
A. PTZ cameras can be input to the Termnial block No. 4&5&6(GND). You can see the compatibility
list of PTZ camera from APPENDIX of this manual.
B. Keyboard Controller can be connected to the Terminal block No. 2&3.
PTZ might be not working perfectly if there is no connection for GND
② Sensor / Relay / POS
Sensor and Relay type
NC(Normal Close): Normal close and Event open
NO(Normal Open): Normal open and Event close
29
A. Sensor connection
I. Sensors can be input to the Terminal Block S1 ~S6.
II. It can be connected regardless of channel numbers.
B. Relay connection
I. Relay can be input to the Terminal Block R1~R4.
II. Relay can be connected to the Alarm action devices like Siren or Light bar.
C. POS connection
I. POS (RS-232c) can be input the Terminal Block No. 1
Please note that relay might be not working depending on the types. In this
case, power supply has to be connected to the relay.
NTSC/PAL Setting
Open the top case of DVR then change the setting with “2pin Jumper” on the board.
NTSC / PAL SELECT Direction :
JP2
The way of setting
JUMPER OPEN : NTSC
JUMPER SHORT : PAL
Please don’t change this setting without any reason as we provide the products
with correct setting normally.
30
Chapter 3. Operation and Setup
DVR can be controlled easily by Front panel, Remote controller, Mouse.
3-１Kute series front panel
No.
Name
Function
1
POWER LED
System power LED
2
RECORD LED
HDD status LED
3
ALARM LED
Event or Motion LED
4
IR Sensor
Remote controller receiving sensor
5
USB
USB mouse, USB memory stick
31
3-２Lite series front panel
No.
Name
Function
1
POWER
Power on/off
2
MOVE & DISPLAY & Select
Moves from one category to antoher or changes the
display mode
3
ESC
Exit the current menu or selects the upper menu
4
MENU
Various modes
5
PLAY
Backward Playback/Rewind (in the Playback Mode)
6
Frame by Frame
Playback frame by frame
7
PAUSE
Pause (in the Playback Mode)
8
Reverse Frame by Frame
Backward Playback frame by frame (in the Playback
Mode
9
Reverse Play
Backward Playback/Rewind (in the Playback Mode)
10
POWER LED
System power LED
11
RECORD LED
HDD(recording) LED
12
LABEL
Badge space to be shown model number or brand
13
USB
USB mouse, USB memory stick
32
3-３Blue series front panel
No.
Name
Function
1
POWER LED
System power LED
2
POWER
Power on/off
3
USB
USB mouse, USB memory stick
4
MOVE & DISPLAY
Moves from one category to antoher or changes the display
mode
5
MENU
Various modes
6
ESC
Exit the current menu or selects the upper menu
7
NUMBER
Channel Selection or Number Input
8
Forward Play / Fast Forward &
PLAY
Playback/Fast Forward (in the Playback Mode)
Play back (in the Monitoring Mode)
9
Forward Frame by Frame &
LOG
Playback Frame by Frame (in the Playback Mode)
System Log View(in the Monitoring Mode)
10
Pause &
LOCK
Pause (in the Playback Mode)
Lock (in the Monitoring Mode)
11
Reverse Frame by Frame &
STATUS
Backward Playback Frame by Frame (in the Playback Mode)
View System Configuration (in the Monitoring Mode).
12
Reverse Play / Fast Reverse &
RELAY
Backward Playback/Rewind (in the Playback Mode)
Relay Control (in the Monitoring Mode)
13
SEARCH
Search the recorded Image.
14
BACKUP
Save the recorded image at other media.
15
CAPTURE
Capture the displaying image into USB
16
PTZ
Pan/Tilt/Zoom control
17
SPOT
Spot Control
18
Eject
CD, DVD Media
19
ODD
CD-RW, DVD-RW
20
ERROR LED
Fan, Recording error indication LED
21
ALARM LED
Event, Motion indication LED
22
NETWORK LED
Remote connection indication LED
23
RECORD LED
HDD operation indication LED
24
LABEL
Badge space to be shown model number or brand
33
3-４Deluxe series front panel
No.
Name
Function
1
LED DISPLAY
HDD and System Power and Status Indication LED
2
POWER
Turn the system power ON or OFF
3
USB
Connection port to the USB mouse and USB memory
stick
4
JOG SHUTTLE
Speed in Playback Mode / Play Direction / Frame Play
5
MENU
Various Modes
6
ESC
Exit the current menu or move to the upper menu
7
MOVE & DISPLAY
Move from one category to another or change to the
display mode or select
8
NUMBER
Channel Selection or Number Input
9
Reverse Play / Fast Reverse &
RELAY
Backward Playback/Rewind (in the Playback Mode)
Relay Control (in the Monitoring Mode)
Reverse Frame by Frame &
STATUS
Backward Playback Frame by Frame (in the Playback
Mode)
View System Configuration (in the Monitoring Mode).
Pause &
LOCK
Pause (in the Playback Mode)
Lock (in the Monitoring Mode)
Forward Frame by Frame &
LOG
Playback Frame by Frame (in the Playback Mode)
System Log View(in the Monitoring Mode)
Forward Play / Fast Forward &
PLAY
Playback/Fast Forward (in the Playback Mode)
Play back (in the Monitoring Mode)
10
SPOT
Spot Control
PTZ
Pan/Tilt/Zoom control
CAPTURE
Capture the displaying image into USB
BACKUP
Save the recorded image at other media.
SEARCH
Search the recorded Image.
11
Eject
CD, DVD Media
12
ODD
CD-RW, DVD-RW
13
LABEL
Badge space to be shown model number or brand
34
3-５Remote controller
3-５-１Remote controller A-Type
① Basic control button
POWER
System power on/off
RECORD
Recording all channels or stop
recording
NUMBER
Input numbers or channels
ID
Selection DVR ID
② System operation and setup button
MENU
Recording, Schedule, System setup
ESC
Exit the current menu
or Move to the upper menu.
SEARCH
Search for the recording data
SELECT
Select the category or execute
sequence disply.
BACK UP
Copy for recording data
PTZ
PTZ control
MOVE
Move from one category to another
or change to the display mode.
35
③ Search Button (playback mode)
Play /
Fast Forward
Frame by Frame
Pause
Reverse Frame by Frame
Reverse Play /
Fast Reverse
④ Other buttons (Monitoring mode)
PLAY
LOG
LOCK
INFO
RELAY
※ Setting up the remote controller ID
Example) in order to control DVR with ID#1, please set as same as below.
Press ID button press the number 0 and 1 press ID button again.
In order to control all of DVRs having different ID at the same time, please set number 999.
36
3-５-２Remote controller B-type
① Basic Control Button
POWER
Not Supported
MODE
Not Supported
FULL
1ch mode
QUAD
4ch mode
9 SPLIT
9ch mode
16 SPLIT
16ch mode
(if you press more, it will be extend like
24ch mode…so on)
SEQ.
Sequnce Mode ON/OFF
② System operation and setup button
MENU
Reording, Schedule, System setting
ESC
Exit the current menu or Move to the
upper menu
PREV
Backward by frame
PAUSE
Pause
FORWARD
Forward by frame
BACKWARD
Backward palyback
PLAY
Playback
3-６Mouse
USB mouse point will be shown after connecting to the DVR.
Click on the right
button
Monitoring Mode / Move from Play Mode to Monitoring
Menu / Pop up or remove Play Menu.
Show sub-folder of the certain Menu window.
Click on the left
button
Select Menu.
Double click on the
left button
Select Menu.
Click the left button
and drag
Move a certain window.
37
3-７Jog/Shuttle
It is useful to control playback.
Front image
Side image
Speed and direction control
Frame control
※ Play Direction Control
This is available in the playback mode. Turning the jog right/left plays
forward/reverse frame by frame.
※ Speed and Direction Control
This is available in the playback mode. Turning the jog right/left plays
forward/reverse x1/x2/x4/x30.
38
Chapter 4. DVR HDD Installation
4-１ Kute series HDD installation
※ Step 1
1) open the top case
1) Normal termination of the system and fully unplugged power code
are required before conducting HDD installation.
2) Touch a grounded metal substance or ground yourself before
installing HDD in order to reduce static electricity. Static electricity may
cause a malfunction of the product.
3) After installing HDD, Do not connect to power supply with the top
case opened. The top case must be covered before usage.
※ Step 2
2) Unscrew and separate the HDD bay from body.
3) Screw the additional HDD bay to current HDD bay
4) Connect HDD to HDD connector on the main board directly without cable.
Reassemble the top case by reversing 1) to finalizing HDD installation.
39
4-２Lite series HDD installation
※ Step 1
1) Normal termination of the system and fully unplugged power code
are required before conducting HDD installation.
2) Touch a grounded metal substance or ground yourself before
installing HDD in order to reduce static electricity. Static electricity may
cause a malfunction of the product.
3) After installing HDD, Do not connect to power supply with the top
case opened. The top case must be covered before usage.
※ Step 2
2) Unscrew and separate the HDD bay from body.
3) Screw the additional HDD bay to current HDD bay
4) Connect HDD to HDD connector on the main board directly without cable.
Reassemble the top case by reversing 1) to finalizing HDD installation.
40
4-３Blue series HDD installation
※ Step 1
1) Normal termination of the system and fully unplugged power code
are required before conducting HDD installation.
2) Touch a grounded metal substance or ground yourself before
installing HDD in order to reduce static electricity. Static electricity may
cause a malfunction of the product.
3) After installing HDD, Do not connect to power supply with the top
case opened. The top case must be covered before usage.
※ Step 2
2) Unscrew and separate the HDD bay from body.
※ Step 3
3) Screw the HDDs to the HDD bay.
※ Step 4
4) As per the photo, Screw the HDD bay, HDD and DVD to the top bay.
※ Step 5
5) Connect the power cable and data cable on HDDs and then reassemble
the top case by reversing 1) to finalizing HDD installation.
41
4-４Deluxe series HDD installation
※ Step 1
1) Using a screw driver, unscrew and take off the top case of the
product.
1) Normal termination of the system and fully unplugged power
code are required before conducting HDD installation.
2) After installing HDD, Do not connect to power supply with
the top case opened. The top case must be covered before
usage.
※ Step 2
2) Using a screw driver, unscrew the fixing bolt of the top HDD bay
② and separate the top HDD bay② from the body.
3) Using a screw driver, unscrew the fixing bolt of the bottom HDD
bay① and separate the bottom HDD bay① from the body.
42
※ Step 3
4) Align screw holes and screw and fix HDD onto the bottom HDD
bay①.
5) Align screw holes and screw and fix HDD onto the top HDD
bay②
6) By reversing Step 2, combine both top② and bottom① HDD bay
with the body.
1) HDD power and data terminal should face the
inner direction.
※ Step 4
7) Reassemble the top case by reversing 1) to finalizing HDD
installation.
43
APPENDIX
A/P/P/E/N/D/I/X
Recommended PTZ Camera Protocol
NO
Vendor
Model
Protocol
1
A.D.
ULTRA_7
SENSORMATIC
ULTRA_8
2
CHOU
COHU3925
COHU
3
Dongyang
Dongyang
DRX-500
DY-255
4
DYNACOLOR
DSCP
DSCP
5
EYE VIEW
EYE VIEW
EYE VIEW
6
FINE SYSTEM
CRR-1600i/s
CRR-1600i/s
7
GE
GE
GE_KARATEL
8
GSP
GSP
CYBERSCAN_1
9
HITRON
FASTRAX2
FASTRAX2
10
HONEYWELL
SCANDOME2
HSDN-251
11
LG
LG
LG_MULTIX,
LG_OLD
12
MIKAMI
MIKAMI
MIKAMI
13
ORIENTAL
ORX-1000
ORX-1000
14
PANASONIC
WVCS854
WVCS854
15
PELCO
PELCO
PELCO – D
PELCO - P
16
PHILIPS
PHILIPS
PHILIPS
17
PROLINE
PROLINE
PROLINE_UK
18
RIFATRON
RIFATRON-1
RIFATRON
19
SAMSUNG TECHWIN
SAMSUNG
SPD-1600
SCC641
20
SUNJIN
SUNJIN
SUNJIN
21
VICON
VICON
VICON
22
YOKO
YOKO
YOKO
Loading...