RIDGID R6000-1 User Manual

Page 1
OPERATOR’S MANUAL
DOUBLE INSULATED
R6000-1
Your drywall screwdriver has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID® product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
1
Page 2
TABLE OF CONTENTS
Introduction ...................................................................................................................................................................... 2
General Safety Rules .....................................................................................................................................................3-4
Specific Safety Rules ........................................................................................................................................................ 4
Symbols .........................................................................................................................................................................5-6
Electrical ........................................................................................................................................................................... 7
Features ............................................................................................................................................................................ 8
Assembly .......................................................................................................................................................................... 9
Operation ...................................................................................................................................................................10-11
Maintenance ................................................................................................................................................................... 12
Warranty .........................................................................................................................................................................13
Customer Service Information ........................................................................................................................................ 14
INTRODUCTION
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability have been given top priority in the design of this product making it easy to maintain and operate.
2
Page 3
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS WORK AREA
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
ELECTRICAL SAFETY
Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way.
Double insulation wire grounded power cord and grounded power supply system.
Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec­tric shock.
Do not abuse the cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords immediately. Damaged cords increase
the risk of electric shock.
When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These cords
are rated for outdoor use and reduce the risk of electric shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating
power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
eliminates the need for the three-
Avoid accid ental startin g. B e sure switch is off before plugging in. Carrying tools with your finger on the
switch or plugging in tools that have the switch on invites accidents.
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the tool in unexpected situations.
TOOL USE AND CARE
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and may lead to loss of control.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off. Any
tool that cannot be controlled with the switch is danger ous and must be repaired.
Disconnect the plug from power source before making
any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
Store idle tools out of the reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by
poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used on another tool.
Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based products, or any strong solvents to clean your tool. Fol­lowing this rule will reduce the risk of loss of control and deterioration of the enclosure plastic.
3
-
Page 4
GENERAL SAFETY RULES
SERVICE
Tool service must be performed only by qualified re-
pair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
SPECIFIC SAFETY RULES
Hold tool by insulated gripping surfaces when per-
forming an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the cutting tool “live” and shock the operator.
Know your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock, fire, or serious injury.
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT safety glasses. Following this rule will reduce the risk of serious
personal injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the risk
of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Inspect tool cords periodically and, if damaged, have
repaired at your nearest authorized service center. Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should be carefully checked to determine that it will operate
When servicing a tool, use only identical replacement
parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance instructions may create a risk of shock or injury.
properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gauge size (A.W.G.) of at least 14 is rec­ommended for an extension cord 50 feet or less in length. A cord exceeding 50 feet is not recommended. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. An undersized
cord will cause a drop in line voltage resulting in loss of power and overheating.
Inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
If the power supply cord is damaged, it must be replaced
only by the manufacturer or by an authorized service center to avoid risk.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
4
Page 5
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
min Minutes Time
Alternating Current Type of current
Direct Current Type or a characteristic of current
n
o
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
No Load Speed Rotational speed, at no load
Class II Construction Double-insulated construction
DESIGNATION/EXPLANATION
Wet Conditions Alert Do not expose to rain or use in damp locations.
Read The Operator’s Manual
Eye Protection
Safety Alert Precautions that involve your safety.
No Hands Symbol
No Hands Symbol
No Hands Symbol
No Hands Symbol
To reduce the risk of injury, user must read and understand operator’s manual before using this product.
Always wear safety goggles or safety glasses with side shields and, as necessary, a full face shield when operating this product.
Failure to keep your hands away from the blade will result in serious personal injury.
Failure to keep your hands away from the blade will result in serious personal injury.
Failure to keep your hands away from the blade will result in serious personal injury.
Failure to keep your hands away from the blade will result in serious personal injury.
Hot Surface
To reduce the risk of injury or damage, avoid contact with any hot surface.
5
Page 6
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
WARNING:
CAUTION:
CAUTION:
Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property damage.
SERVICE
Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the product to your nearest AUTHORIZED SERVICE CENTER for repair. When servic­ing, use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt to use this product until you read thoroughly and understand completely the operator’s manual. If you do not understand the warnings and instructions in the operator’s manual, do not use this product. Call RIDGID® customer service for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
6
Page 7
ELECTRICAL
DOUBLE INSULATION
Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protect­ing insulation. Double insulated tools do not need to be grounded.
WARNING:
The double insulated system is intended to protect the user from shock resulting from a break in the tool’s internal wiring. Observe all normal safety precautions to avoid electrical shock.
NOTE: Servicing of a product with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the tool to your nearest authorized service center for repair. Always use original factory replace­ment parts when servicing.
ELECTRICAL CONNECTION
This tool has a precision-built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the tool does not operate when plugged into an outlet, double-check the power supply.
EXTENSION CORDS
When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the product will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter’s Laboratories (UL) should be used.
When working outdoors with a product, use an extension cord that is designed for outside use. This type of cord is designated with “WA” on the cord’s jacket.
Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation.
**Ampere rating (on product data plate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25' 16 16 16 16 14 14
50' 16 16 16 14 14 12
100' 16 16 14 12 10
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools, or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury.
WARNING:
Check extension cords before each use. If damaged replace immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.
7
Page 8
FEATURES
PRODUCT SPECIFICATIONS
Bit Shank ..................................................................1/4 in.
Switch .........................................................Variable Speed
No Load Speed .................................0-4,000 r/min. (RPM)
BELT CLIP
ADJUSTABLE
NOSEPIECE
Input ............................... 120 V, 60 Hz, AC only, 6.5 Amps
Net Weight .............................................................. 3.1 lbs.
FORWARD/
REVERSE
LEVER
SWITCH
TRIGGER
LOCK-ON
BUTTON
MAGNETIC BIT
HOLDER
KNOW YOUR DRYWALL SCREWDRIVER
See Figure 1.
The safe use of this product requires an understanding of the information on the product and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules.
ADJUSTABLE NOSEPIECE
The screwdriver has an adjustable nosepiece for varying screw depth and easy bit changes.
BELT CLIP
A convenient belt clip is located on top of the motor housing.
DUAL GRIP HANDLE
The soft-grip handle is designed with two grip position op­tions for operator comfort and ease of handling.
FORWARD/REVERSE LEVER
The forward/reverse lever changes the direction of bit rotation.
LIGHTED PLUG
Fig. 1
LIGHTED PLUG
The lighted plug helps to easily identify live tools.
LOCK-ON BUTTON
The lock-on feature allows for continuous driving of screws for extended periods of time.
MAGNETIC BIT HOLDER
The magnet holds the screwdriver bit and screws until you are ready to drive them into drywall.
POWER CORD
The drywall screwdriver has a 12-foot power cord with a built-in cord wrap. The shape of the plug is designed not to snag on the workpiece.
SWITCH TRIGGER
The switch trigger for the drywall screwdriver is conveniently located on the handle of the tool.
VARIABLE SPEED
The variable speed switch delivers higher speed with in­creased trigger pressure.
8
Page 9
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list are included.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
PACKING LIST
Drywall Screwdriver with Magnetic Bit Holder and #2 Phillips Bit installed
R2 Square Recess Screwdriver Bit
Operator’s Manual
WARNING:
If any parts are damaged or missing do not operate this product until the parts are replaced. Failure to heed this warning could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.
INSTALLING AND REPLACING BIT HOLDER AND BITS
See Figure 2.
To install or replace bits:
Install 1/4 in. screwdriver bits by inserting them into the
magnetic bit holder.
NOTE: It is not necessary to remove the adjustable nose-
piece to install or remove bits.
Replace 1/4 in. screwdriver bits by pulling them out of
the magnetic bit holder.
To remove the magnetic bit holder:
Pull the adjusting sleeve. The adjusting sleeve and adjust-
able nosepiece come off the gear casing as a set.
Remove the magnetic bit holder. Pull the bit holder out
with pliers if you cannot remove it by hand.
To reassemble the bit holder and nosepiece:
Push the bit holder into the hex opening of the spindle
until the ball lock snaps into the groove in the bit holder shank.
Attach the adjustable nosepiece to the gear case. Align
the raised tab inside the adjustable nosepiece with the groove on the gear case and push the nosepiece until it snaps into place.
1/4 in. PHILLIPS
SCREWDRIVER BIT
R2 BIT
PULL TO REMOVE
ADJUSTABLE
NOSEPIECE
REPLACE ADJUSTABLE
ADJUSTABLE
NOSEPIECE
ADJUSTING
SLEEVE
ALIGN AND PUSH TO
NOSEPIECE
BELT CLIP
GROOVE
GEAR
CASING
MAGNETIC BIT HOLDER
WITH 1/4 in. HEX OPENING
Fig. 2
9
Page 10
OPERATION
WARNING:
Do not allow familiarity with products to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury.
WARNING:
Always wear safety goggles or safety glasses with side shields when operating products. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.
APPLICATIONS
You may use this product for the purpose listed below:
Driving screws in drywall
FORWARD/
REVERSE LEVER
SWITCH
TRIGGER
REVERSE
LOCK-ON
BUTTON
Fig. 3
FORWARD
STARTING/STOPPING THE SCREWDRIVER
See Figure 3.
To turn the screwdriver ON, depress the switch trigger. Re­lease the switch trigger to turn the screwdriver OFF.
VARIABLE SPEED
The screwdriver has a variable speed switch for operator control of speed and torque limits.
Depress the switch trigger all the way for maximum speed and torque. Depress the switch trigger only part of the way for less speed and torque.
Avoid running the tool at low speeds for extended periods of time. Constant use at low speeds may cause overheating. If this occurs, cool the screwdriver by running it without a load and at full speed.
LOCK-ON BUTTON
See Figure 3.
The screwdriver is equipped with a lock-on feature which is convenient for continuous driving of screws for extended periods of time. To lock-on, depress the switch trigger, push in and hold the lock-on button located on the side of the handle, then release switch trigger. Release the lock-on but­ton and the screwdriver will continue running.
To release the lock, depress the switch trigger and re­lease.
If you have the lock-on feature engaged during use and the screwdriver becomes disconnected from the power supply, disengage the lock-on feature immediately.
Fig. 4
FORWARD/REVERSE LEVER
See Figure 4.
The direction of rotation of the bit is controlled by a lever located above the switch trigger. With the screwdriver held in normal operating position, the direction of rotation lever should be positioned to the left of the switch for forward driving operation. The direction of rotation is in reverse when the lever is to the right of the switch.
NOTE: The screwdriver will not run unless the forward/re­verse lever is pushed fully to the left or right. The design of the switch will not permit changing the direction of rotation while the screwdriver is running. Release the switch trig­ger and allow the screwdriver to stop before changing its direction.
10
Page 11
OPERATION
SETTING DEPTH
See Figure 5.
The adjustable nosepiece of the tool will automatically drive screws to preset depths. It may be helpful to begin each new job by driving several test screws in scrap material to check and adjust the depth setting.
To make preset depth adjustments:
Rotate the adjusting sleeve until you obtain the desired
depth for the bit holder or screwdriver bit.
Test drive a screw in scrap material to determine if it is
correct.
Adjust as necessary to increase or decrease the desired
depth.
DRIVING SCREWS
See Figures 6 - 7.
There are two two options for gripping the handle of the screwdriver, determined by operator comfort and working angle.
The screwdriver has a variable speed switch for operator control of speed and torque limits.
Be sure the screwdriver is in the OFF position before
connecting it to the power supply.
Check the direction of rotation lever for correct setting
(forward or reverse).
Secure the workpiece. Use clamps if necessary.
Plug the screwdriver into power supply source.
Depress the switch trigger to start the screwdriver. Do not
lock the switch ON for jobs where the screwdriver may need to be stopped suddenly.
Hold the screwdriver firmly and place the bit and screw
at the point to be driven.
NOTE: The bit holder is magnetized and will hold most
commercial drywall screws.
Apply quick, snap action type pressure to the bit. The
pressure applied will engage the clutch and drive the screw.
TO DECREASE DEPTH OF
SCREWDRIVER BIT
TO INCREASE
DEPTH OF
SCREWDRIVER BIT
PRESET DEPTH
SETTING OF
SCREWDRIVER BIT
Fig. 5
Fig. 6
11
Fig. 7
Page 12
MAINTENANCE
WARNING:
When servicing use only identical RIDGID® replacement parts. Use of any other parts may create a hazard or cause product damage.
WARNING:
Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personal injury.
Electric tools used on fiberglass material, wallboard, spack ling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommend using this product for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the product us­ing compressed air.
LUBRICATION
All of the bearings in this product are lubricated with a suf­ficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required.
-
12
Page 13
WARRANTY
RIDGID® HAND HELD AND STATIONARY POWER TOOL 3 YEAR LIMITED SERVICE WARRANTY
Proof of purchase must be presented when requesting warranty service.
Limited to RIDGID® hand held and stationary power tools purchased 2/1/04 and after. This product is manufactured by One World Technologies, Inc. The trademark is licensed from RIDGID, Inc. All warranty communications should be directed to One World Technologies, Inc., attn: RIDGID Hand Held and Stationary Power Tool Technical Service at (toll free) 1-866-539-1710.
90-DAY SATISFACTION GUARANTEE POLICY
During the first 90 days after the date of purchase, if you are dissatisfied with the performance of this RIDGID® Hand Held and Stationary Power Tool for any reason you may return the tool to the dealer from which it was purchased for a full refund or exchange. To receive a replacement tool you must present proof of purchase and return all original equipment packaged with the original product. The replacement tool will be covered by the limited warranty for the balance of the 3 YEAR service warranty period.
WHAT IS COVERED UNDER THE 3 YEAR LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power Tools covers all defects in workmanship or materials and normal wear items such as brushes, chucks, motors, switch­es, cords, gears and even cordless batteries in this RIDGID® tool for three years following the purchase date of the tool. Warranties for other RIDGID® products may vary.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID® tool you must return it; freight prepaid, or take it in to an authorized service center for RIDGID® branded hand held and stationary power tools. You may obtain the location of the authorized service cen­ter nearest you by calling (toll free) 1-866-539-1710 or by logging on to the RIDGID® website at www.ridgid.com. When requesting warranty service, you must present the original dated sales receipt. The authorized service center will repair any faulty workmanship, and either repair or replace any part covered under the warranty, at our option, at no charge to you.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail and may not be transferred. This warranty only covers defects arising under normal usage and does not cover any malfunction, failure or defect resulting from misuse, abuse, neglect, alteration, modification or repair by other than an authorized service center for RIDGID® branded hand held and stationary power tools. Consumable accessories provided with the tool such as, but not limited to, blades, bits and sand paper are not covered.
RIDGID, INC. AND ONE WORLD TECHNOLOGIES, INC. MAKE NO WARRANTIES, REPRESENTATIONS OR PROMISES AS TO THE QUALITY OR PERFORMANCE OF ITS POWER TOOLS OTHER THAN THOSE SPECIFI CALLY STATED IN THIS WARRANTY.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, including warranties of merchant­ability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to three years from the date of purchase. One World Technologies, Inc. and RIDGID, Inc. are not responsible for direct, indirect, incidental or co nsequential damages. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
One World Technologies, Inc.
P.O. Box 35, Hwy. 8
Pickens, SC 29671
-
13
Page 14
OPERATOR’S MANUAL
DOUBLE INSULATED
R6000-1
987000-143 5-07-07 (REV:00)
Customer Service Information:
For parts or service, contact your nearest RIDGID® authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at www.ridgid.com.
The model number of this product is found on a plate attached to the motor hous-
ing. Please record the serial number in the space provided below. When ordering
repair parts, always give the following information:
Model No.
Serial No.
R6000-1
14
Loading...