2005-2011 MUSTANG TIGER CAGE
SHOULDER SEAT BELT BAR INSTRUCTIONS MANUAL
PAGE 1
Thank you for purchasing our 2005 -2011 Mustang
Tiger Cage Shoulder Seat Belt Bar. Please read
through all of the instructions first and then start
installing the kit.
We hope that you enjoy the added performance that
this products brings to your Mustang.
www.ridetech.com
PAGE 2
2005-2011 MUSTANG TIGER CAGE
SHOULDER BAR ASSEMBLY
COMPONENTS LIST
PART #42153000
PART # 42153000 MUSTANG TIGER CAGE DOOR BAR ASSEMBLY COMPONENTS:
QTY. PART # DESCRIPTION
1 42153001 MUSTANG SEAT BELT BAR
2 49990005 TIGER CAGE ROLL BAR PIVOT PLATE
1 49990003 TIGERCLAMP P ½ (THREADED)
1 49990001 TIGERCLAMP P ½
1 49990004 TIGERCLAMP D ½ (THREADED)
1 49990000 TIGERCLAMP D ½
1 99010003 MUSTANG TIGER CAGE SHOULDER BAR FASTENER ASSEMBLY
350 S. St. Charles St. Jasper, In. 47546
Ph. 812.482.2932 Fax 812.634.6632
www.ridetech.com
1 TUBE OF ANTI-SEIZE
3PAGE
FASTENER LIST SEAT BELT BAR
Use anti-seize on all fasteners that are threaded into
stainless clamps or brackets. Torque all 3/8”and M10
fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs
SEAT BELT BAR FASTENER KIT PART # 99010003
3 1
Item
Number
1 3/8" X 16 - 1" LONG SS
ALLEN HEAD
2 1/2" - 20 X 1 1/2" LONG
12 POINT FLANGE HEAD
CAP SCREW
3 1/2" - 20 HEX NUT Nickel
Title Material Quantity
Nickel
Plated
Steel
Nickel
Plated
Steel
Plated
Steel
2
8
2
2
4PAGE
COMPONENTS IN KIT
42153001 MUSTANG SEAT BELT BAR QTY 1
49990004 TIGER CAGE CLAMP QTY 1
49990000 QTY 1
49990003 QTY 1
49990001 QTY 1
49990005 TIGER CAGE
PIVOT PLATE QTY 2
5PAGE
SHOULDER SEAT BELT BAR PART
ASSEMBLY PART # 42153000
•This is the Shoulder Seat Belt Bar Assembly for the 2005-2011 Mustang
Tiger Cage.
•This kit comes with everything to attach it to the Mustang Tiger Cage
Main Assembly Hoop.
6PAGE
TIGER CLAMP
•In order to keep the “T” in the casting facing up, and the bolts facing the correct direction, there are
two different direction clamps. Clamp half “A” will be mated to clamp half “B”, Clamp half “C” will be
mated to clamp half “D”. Be very careful as to which clamp halves you are bolting together.
•In order to keep the “T” in the casting facing up, and the bolts facing the correct direction, there are
two different direction clamps. Be very careful as to which clamp halves you are bolting together.
•A correctly assembled clamp should look like the one in the picture shown above; there should be a
gap on one side for the tab to slide into.
•Assemblethe clamps to the main hoop. Use clamp D on the driver side and clamp P on the passenger
side.
7PAGE
INSTALLATION OF SEAT BELT BAR
fig(1)
• First step is to take the Tiger Cage Clamp and align it to the Mustang Main Hoop.
• Install the Tiger Cage pivot plate to the clamp with two 3/8”-16 x 1” allen head bolts. (see fig1)
• Make sure the clamp is exactly where you want it before tightening as the clamp may scratch the
tubing.
• Install the other two 3/8”-16 x 1”bolts to the clamp (see fig2)
8PAGE
INSTALLATION OF MUSTANG SEAT BELT
BAR
fig (2)
• Install the Mustang Seat Belt Bar into the Tiger Cage pivot plate.
• Install two ½” -20 1 ½” long 12 point bolts into the seat belt bar and
two ½”-20 nuts.
• Repeat these steps to the passenger side of the car.
9PAGE
INSTALLED MUSTANG SEAT BELT BAR
•The Mustang Shoulder Seat Belt Bar can be adjusted on the main hoop to the desired
location and clamped.
•Now your install is complete.
10PAGE
Loading...