Ridetech 42152000 User Manual

2005-2011 MUSTANG TIGER CAGE
PAGE
ROAD RACE BAR INSTRUCTIONS MANUAL
1
Thank you for purchasing our 2005 -2011 Mustang Tiger Cage Road Race Bar Assembly. Please read through all of the instructions first and then start installing the kit.
We hope that you enjoy the added performance that this products brings to your Mustang.
www.ridetech.com
2PAGE
2005-2011 MUSTANG TIGER CAGE
ROAD RACE BAR ASSEMBLY
COMPONENTS LIST
PART #42152000
PART # 42152000 MUSTANG TIGER CAGE ROAD RACE BAR ASSEMBLY COMPONENTS:
QTY. PART # DESCRIPTION
2 42152001 MUSTANG SEAT BRACKET FRONT LOWER 2 42150009 MUSTANG LOWER PLATE 1 42152003 MUSTANG DOOR BAR BRACKET UPPER DRIVER SIDE 1 42152004 MUSTANG DOOR BAR BRACKET UPPER PASSENGER SIDE 2 42152005 MUSTANG DOOR BAR BENT BRACKET 1 42152006 MUSTANG ROAD RACE BAR DRIVER SIDE 1 42152007 MUSTANG ROAD RACE BAR PASSENGER SIDE 2 49990005 TIGER CAGE ROLL BAR PIVOT PLATE 1 49990003 TIGERCLAMP P ½ (THREADED) 1 49990001 TIGERCLAMP P ½ 1 49990004 TIGERCLAMP D ½ (THREADED) 1 49990000 TIGERCLAMP D ½ 1 99010002 MUSTANG TIGER CAGE DOOR BAR FASTENER ASSEMBLY
350 S. St. Charles St. Jasper, In. 47546
Ph. 812.482.2932 Fax 812.634.6632
www.ridetech.com
1 TUBE OF ANTI-SEIZE
3PAGE
FASTENER LIST ROAD RACE BAR
Use anti-seize on all fasteners that are threaded into stainless clamps or brackets. Torque all 3/8”and M10
fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs
ROAD RACE BAR FASTENER KIT PART # 99010002
2 1 5
Item
Number
1 3/8" FLAT WASHER Zinc 14
2 3/8" X 16 - 1" LONG SS
3 3/8"-16 LOCKING NUT Zinc 12 4 1/2" - 20 X 1 1/2" LONG
5 1/2" - 20 HEX NUT Nickel
6 M10 - 1.5MM 30MM LONG Nickel
7 3/8" - 16 x 1 1/2" long
8 3/8" x 1 1/2" -16 BOLT Zinc 2
Document
Number
2 6
Title Material Quantity
ALLEN HEAD
12 POINT FLANGE HEAD CAP SCREW
socket head cap screw
PAGE
Nickel Plated Steel
Nickel Plated Steel
Plated Steel
Plated Steel
Nickel Plated Steel
8
8
2
2
2
10
7
4
4
COMPONENTS IN KIT
42152003 MUSTANG DOOR BAR BRACKET UPPER DRIVER SIDE QTY 1 42152004 MUSTANG DOOR BRACKET UPPER PASSENGER SIDE QTY 1
49990004 TIGER CAGE CLAMP QTY 1 49990000 QTY 1 49990003 QTY 1 49990001 QTY 1
49990005 TIGER CAGE
PIVOT PLATE QTY2
42150009 MUSTANG
LOWER PLATE QTY 2
5PAGE
COMPONENTS IN KIT
42152006 MUSTANG DOOR BAR DRIVER SIDE QTY 1 42152007 MUSTANG DOOR BAR PASSENGER SIDE QTY 1
42152001 MUSTANG SEAT BRACKET FRONT LOWER QTY 2
6PAGE
Fig (1)
PARTS TO REMOVE BEFORE INSTALLATION
FACTORY NUTS
FACTORY BOLTS
Removal of the seat fasteners is recommended to allow you more access to install the Tiger Cage Road Race bars.
There are 2 bolts in the front of the seat, and two nuts in the rear of the seat that hold the seat to the floor pan (see fig 1).
Another good idea that we do here at Ridetech is masking off the door jamb area to keep it from being scratched during the installation of the door bars.
7PAGE
REMOVE FRONT KICK PANELS
Driver side kick panel Passenger side kick panel
Remove the front kick panels from the Mustang.
They are clipped on.
The passenger side also has the fuse panel door that will need to be
removed with the kick panel.
Next roll the carpet back.
8PAGE
MODIFICATION OF PASSENGER SIDE
KICK PANEL
Fig(3)
The passenger side front kick panel will need to be modified for the Door Bar to fit.
It will need to be cut out for clearance to the Door bar as shown. (see fig 3).
PAGE
9
REAR SEAT TRACK MODIFICATION
The Mustang seat track has a tab on the rear of it.
This tab must be bent down for the Door Bar
brackets to fit.
10PAGE
REMOVE BOLTS FROM EXISTING
UPPER MAIN HOOP BRACKETS
REMOVE THESE FASTENERS
Fig (4)
The front bolts on the Main Hoop Upper Brackets will need to be removed for the installation of the Door Bars. (see fig 4)
11PAGE
ROAD RACE BAR PART # 42152006
AND PART # 42152007 INSTALLATION
The Mustang Road Race Door Bar Assembly Kit is an optional kit that works with the Mustang Main Hoop Assembly.
This kit uses some of the existing brackets from the Mustang Main Assembly kit.
12PAGE
INSTALLATION OF PART #42152003
AND PART #42152004
FUEL PUMP RESET SWITCH Fig (5)
EXISTING BOLTS
The first bracket to install is the Mustang Door Bar bracket upper driver side.
This bracket is aligned to two existing bolts that are located under the fuel pump reset
EXISTING BOLTS
switch. (see fig 5)
Remove the two existing bolts.
Line up the bracket to the existing holes.
Install the two bolts back into the kick panel and tighten.
13PAGE
INSTALLATION OF MUSTANG DOOR
BAR BRACKETS
HOLES TO BE DRILLED
Mark the four holes in the Mustang Door Bar bracket.
Drill four 7/16” holes through the floor pan.
Fit the passenger side Mustang Door Bracket Upper the same as the Driver
Side and repeat steps.
These brackets can be installed on top of the carpet or below.
Once they are installed you can reinstall the kick panels.
14PAGE
INSTALLATION OF MUSTANG DOOR BAR
LOCATE THE REAR BRACKET TO
MAIN HOOP UPPER BRKT AND
SEAT STUD
Fig (6)
Fig (7)
Next is the installation of the Mustang Door Bar.
To install the door bar you will need to locate it to the Door Bar Bracket Front and
the Rear Main Hoop Upper Bracket. (see fig 6)
Line up the front of the door bar to the four holes in the Door Bracket upper (see fig 7).
Now you will need to set the door bar into the Mustang and mark where the Front Door Bar support stud hole will need to be drilled.
15PAGE
MUSTANG ROAD RACE DOOR BAR INSTALLATION
STUD LOCATIONFig (7)
Once it is located you will need to drill out a 7/16” hole for the stud located under the front door bar support. (see fig 7)
After the hole is drilled you can put the carpeting back down.
Make sure to cut a hole in the carpet for the stud to go through.
16PAGE
MUSTANG ROAD RACE DOOR BAR INSTALLATION
Fig(8)
Now it is time to put the Road Race Bar into the car.
The easiest way to do this is to roll the seat toward the center of the car with the
door bar underneath it.
Make sure to line up the Mustang Door Bar Support stud to the hole in the floor pan.
The Mustang Front Seat bracket sit on the outside of the front seat bolt location.
(see fig 8)
17PAGE
MUSTANG ROAD RACE DOOR BAR
INSTALLATION
SEAT STUD SLOT
Fig (6)
Now that you have the Road Race bar under the seat and in the car, line up the seat mounting stud on the Mustang Rear Seat Bracket and the Mustang Front Seat bracket to the factory seat mounting holes.
Now install the two 3/8”-16 x 1 ½” bolts (#7), 3/8” flat washers (#1) through the Mustang Rear seat bracket. (see fig 6)
Install the factory rear seat nuts.
Install four 3/8”-16 x 1 ½” long allen head bolts (#7) through the Mustang
Front Door Bracket Upper. (see fig 7)
Fig (7)
18PAGE
INSTALLATION OF ROAD RACE DOOR BAR
Install one 3/8”-16 x 1 ½” long allen head bolt (#7) and 3/8” flat washer (#1) through the Mustang Seat bracket front upper.
19PAGE
LOWER PLATE INSTALLATION
Once the bolts are through the Upper Brackets, you can install the Mustang Lower Plate, and the Mustang Lower Seat Bracket.
Install six 3/8” flat washers (#1), and six 3/8”-16 locking nuts onto the 3/8”-16 x 1 ½” bolts from the upper brackets.
Tighten.
20PAGE
TIGER CLAMP ORIENTATION
In order to keep the “T” in the casting facing up, and the bolts facing the correct direction, there are two different direction clamps. Clamp half “A” will be mated to clamp half “B”, Clamp half “C” will be
mated to clamp half “D”. Be very careful as to which clamp halves you are bolting together.
In order to keep the “T” in the casting facing up, and the bolts facing the correct direction, there are two different direction clamps. Be very careful as to which clamp halves you are bolting together.
A correctly assembled clamp should look like the one in the picture shown above; there should be a gap on one side for the tab to slide into.
Assemblethe clamps to the main hoop. Use clamp D on the driver side and clamp P on the passenger side.
21PAGE
INSTALLATION OF TIGER CLAMPS AND
MUSTANG DOOR BAR BENT BRACKET
MUSTANG BENT BRKT
Fig (9)
Install Tiger Cage Clamp around the Main Hoop.
Insert the Mustang Bent Bracket into the front of the Tiger Clamp. (see fig 9)
Install two 3/8”-16 x 1” (#2) long allen head bolts into the front Tiger Clamp holes.
Install two 3/8”-16 x 1” (#2) long allen head bolts into the rear of the Tiger Clamp.
Install two ½”-20 x 1 ½” (#4) long 12 point bolts into the door bar.
Install two ½” -20 (#5) hex nuts and tighten.
22PAGE
SEAT BOLTS
M10 BOLT
Install the factory seat bolt that is near the tunnel.
The outer bolt will be replaced with a longer bolt supplied in the kit.
Install the M10-1.5mm x 30mm (#6) long bolt into the outer front
Mustang Seat bracket and tighten.
Check all bolts and nuts to make sure they are tight.
Now the Door Bar installation is complete.
23PAGE
MUSTANG ROAD RACE DOOR BAR
INSTALLED
This is what your new Road Race Bar will look like once it is installed.
Please enjoy your new Tiger Cage from Ridetech!!!!!!!!!!
24PAGE
Loading...