350 S. St. Charles St. Jasper, In. 47546
Ph. 812.482.2932 Fax 812.634.6632
www.ridetech.com
TGR14002 68-72 GM “A” Body TigerCage Roadrace Door Bars
DoorBars
1 T134-1 Driver side door bar
1 T135-1 Passenger side door bar
1 T098 Driver side door bar floor mount
1 T099 Passenger side door bar floor mount
2 T102 Kick panel reinforcement plate
1 T100D Driver side inner frame mount
1 T100P Passenger side inner frame mount
2 T104-1 Outer reinforcement plate
4 T002 Clamp tabs
2 T037P TigerClamp P (threaded)
2 T038P TigerClamp P
2 T037D TigerClamp D (threaded)
2 T038D TigerClamp D
1 Tube of Anti-Seize
Hardware:
16 3/8” x 1” USS Gr. 8 SHCS Clamps / Main hoop to mount
18 3/8” x 1 ¼” USS Gr. 8 bolt Mounting brackets
4 3/8” x 1 ¾” USS Gr. 8 bolt Mounting brackets
2 3/8” x 1” self-tapping screw Mounting brackets
20 3/8” USS Gr.8 Nylok nut Mounting brackets
38 3/8” SAE flat washer Mounting brackets
4 ½” x 1 ½” 12 point Gr. 8 bolt Bar to clamp tab
4 ½” Flange nut Bar to clamp tab
2 3/8” x 1 ½” Gr. 8 bolt Seat belt tabs
2 3/8” USS Nylok nut Seat belt tabs
T099 T100 T102 T104-1
TGR14002 Installation Instructions
• Initial fitment of the floor mount brackets must be done under the carpet. Final installation can
be done under or over the carpet.
• Use Anti-Seize on all fasteners that are threaded into stainless clamps or brackets.
• Install all bars before final tightening.
• Always tighten the tab side of the clamp first.
• Torque all 3/8” fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs.
• Make sure the clamp is exactly where you want it before tightening as the clamp may scratch
the tubing.
• Watch for fuel and brake lines when drilling holes through the floor pan.
1. In order to keep the “T” in the
casting facing up, and the bolts
facing the correct direction, there are
two different direction clamps. Be
very careful as to which clamp halves
you are bolting together. Refer to
the image on page 4 for clamp
locations.
2. A correctly assembled clamp
should look like the one in the picture
shown to the left; there should be a
gap on one side for the tab to slide
into.
3. Assemble the clamps to the main
hoop. Use clamp P on the driver
side and clamp D on the passenger
side. Tighten the clamp enough to
be able to position it.
4. Use the ½” x 1 ½” 12 point bolt &
flange nut to fasten the door bars to
the clamps.
5. Position the door bar so that the
top of the upper clamp is 19” above
the main hoop flange. This should
position the door bar just above the
rocker.
5. To install the front floor pan
bracket, the kick panel must be
removed.
6. Use the door bar to determine the
location of the floor pan mount. Drill
two 3/8” holes in the kick panel.
Place the reinforcement plate inside
the kick panel and secure the
assembly with two 3/8” x 1 ¼” bolts,
flat washers and lock washers.
7. Remove the door bars.
8. Using the bracket as a template,
drill four 3/8” holes through the floor
pan. (The middle two do not need to
be drilled).
9. The inner two most holes will bolt
to this bracket using 3/8” x 1 ¼” bolts,
flat washers and Nylok nuts.
10. Using the bracket as a template,
drill four 5/16” holes in the frame rail.
Use four 3/8” x 1” self tapping screws
to fasten the bracket to the frame.
11. Reinstall the door bars. Drop two
3/8” x 1 ¾” bolts down through the
outer two holes. The reinforcement
plate will be installed under the car
(it’s the one with a handle on it to aid
installation). The inner two bolts will
use 3/8” x 1 ¼” bolts, flat washers
and Nylok nuts.
12. Since the door bar covers the
factory lap belt mounting holes, tabs
are welded to the bar to secure the
lap belts. 3/8” x 1 ½” bolts are
supplied.
13. All clamps and bolts may now be
tightened.
Installation Complete!
TigerClamp Location Chart
Loading...