350 S. St. Charles St. Jasper, In. 47546
Ph. 812.482.2932 Fax 812.634.6632
www.ridetech.com
41172000 70-73 Camaro TigerCage
Road Race Door Bar Kit
Door Bars
1 41172901 Driver side road race style door bar assembly
1 41172900 Passenger side road race style door bar assembly
1 41172904 Driver side door bar floor mount
1 41172905 Passenger side door bar floor mount
2 41172906 Door bar floor mount reinforcement plate (under car)
4 41170912 Door bar floor mount reinforcement plate (kick panel)
4 49990005 Clamp tab
2 49990003 TigerClamp P (threaded)
2 49990001 TigerClamp P
2 49990004 TigerClamp D (threaded)
2 49990000 TigerClamp D
1 Tube of Anti-Seize
Hardware:
16 3/8” x 1” USS SHCS Clamps
8 3/8” x 1 3/4” USS Gr. 8 bolt Door bar mount
8 3/8” x 1 ¼” USS Gr. 8 bolt Door bar mount through floor/ kick panel
24 3/8” SAE flat washer Door bar mount
16 3/8” USS Gr. Nylok nut Door bar mount
4 ½” x 1 ½” 12 point Gr. 8 bolt Bar to clamp tab
4 ½” Flange nut Bar to clamp tab
T065 Door Bar Floor Mount T002 TigerClamp Tab T054 Kick Panel Plate T058 Under Car Plate
TGR12002 Installation Instructions
• Initial fitment of the floor mount brackets must be done under the carpet. Final installation can
be done under or over the carpet.
• Use Anti-Seize on all fasteners that are threaded into stainless clamps or brackets.
• Install all bars before final tightening.
• Always tighten the tab side of the clamp first.
• Torque all 3/8” fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs.
• Make sure the clamp is exactly where you want it before tightening as the clamp may scratch
the tubing.
• Watch for fuel and brake lines when drilling holes through the floor pan.
1. In order to keep the “T” in the
casting facing up, and the bolts
facing the correct direction, there are
two different direction clamps. Be
very careful as to which clamp halves
you are bolting together. Refer to
the image on page 4 for clamp
locations.
2. A correctly assembled clamp
should look like the one in the picture
shown to the left; there should be a
gap on one side for the tab to slide
into.
3. Assemble the clamps to the main
hoop. Use clamp P on the driver
side and clamp D on the passenger
side. Tighten the clamp enough to
be able to position it.
4. Use the ½” x 1 ½” 12 point bolt &
flange nut to fasten the door bars to
the clamps.
5. Position the door bar so that the
bottom of the upper clamp is 11 ¼”
above the main hoop flange. This
should position the door bar just
above the rocker.
5. To install the front floor pan
bracket, the kick panel must be
removed. To remove the kick panel
the parking brake assembly must be
removed. It will also help to remove
the dimmer switch. There is also a
bolt and clamp that attach the
parking brake to the floor pan that
must be removed.
6. Use the door bar to determine the
location of the floor pan mount. Drill
two 3/8” holes in the kick panel.
Place the reinforcement plate inside
the kick panel and secure the
assembly with two 3/8” x 1 ¼” bolts,
flat washers and lock washers.
7. Using the bracket as a template,
drill six 3/8” holes through the floor
pan.
8. Hold the reinforcement plate up
against the bottom of the floor pan.
Drop two 3/8” x 1 ¼” bolts through
the inside two holes. The four outer
holes also pass through the door bar
flange and require 3/8” x 1 ¾” bolts.
The outer rear bolt must be installed
from the bottom up to clear the bar.
Installation complete!
TigerClamp Location Chart
Loading...