Ridetech 41160000 User Manual

350 S. St. Charles St. Jasper, In. 47546

Ph. 812.482.2932 Fax [phone]

www.ridetech.com

Part # 41160000

67-69 Camaro TigerCage

Basic Cage

1 41160904 (T046-1) Main hoop assembly

2 41160909 (T025-1) Main hoop mount
2 41160908 (T029) Main hoop reinforcement plate (inside car)
2 41260910 (T013) Main hoop reinforcement plate (under car)
2 49990002 (MISC1011) 1 ¼” plastic plug for rocker panel
1 41160903 (T047-1) Driver side package tray bar
1 41160902 (T048-1) Passenger side package tray bar
2 41160905 (T044) Package tray reinforcement plate
1 41160901 (T049-1) Passenger side trunk bar
1 41160900 (T050-1) Driver side trunk bar
2 41160906 (T032) Trunk bar reinforcement plate (under car- outer)
2 41160907 (T031) Trunk bar reinforcement plate (under car- inner)
2 49990005 (T002) Clamp tab

1 49990003 (T037P) TigerClamp P (threaded)
1 49990000 (T038P) TigerClamp P
1 49990004 (T037D) TigerClamp D (threaded)
1 49990001 (T038D) TigerClamp D
1 Tube of Anti-Seize
Hardware:
16 3/8” x 1” USS Gr. 8 SHCS Clamps / Main hoop to mount
4 3/8” x 1” USS Gr.8 bolt Main hoop mount reinforcement plate to pinch weld
12 3/8” Lock washer Hoop to lower mount mount/ lower mount to plate
32 3/8” x 1 ¼” USS Gr. 8bolt Main hoop mount to reinforcement plates/ trunk bars
32 3/8” USS Gr.8 Nylok nut Main hoop mount reinforcement plates
68 3/8” SAE flat washer Main hoop mount / trunk bars
2 ½” x 1 ½” 12 point Gr. 8 bolt Bar to clamp tab
2 ½” Flange nut Bar to clamp tab

T025-1 Main Hoop Mount T044 Package Tray Plate T031 Trunk Bar Plate-Inner T032 Trunk Bar Plate- Outer

T013 Hoop Plate- Under T029 Hoop Plate- Inside T002 TigerClamp Tab MISC1011 1 ¼” Plug

TGR10000 Installation Instructions

• Initial fitment of the floor mount brackets must be done under the carpet. Final installation can
be done under or over the carpet.

• Use Anti-Seize on all fasteners that are threaded into stainless clamps or brackets.

• Install all bars before final tightening.

• Always tighten the tab side of the clamp first.

• Torque all 3/8” fasteners to 45 ft-lbs and all 1/2” fasteners to 75 ft-lbs.

• Make sure the clamp is exactly where you want it before tightening as the clamp may scratch

the tubing.

• Watch for fuel and brake lines when drilling holes through the floor pan.

1. The first bracket to be mounted
needs to be the main hoop floor
mount. It should be mounted to the
wire trough with the front edge of the
bracket exactly 27” behind the front
edge of the seat mount.

2. Using the bracket as a template,
drill the four holes with a 3/8” bit.

3. The upper portion of the bracket

will fasten to the wire trough with a

reinforcement plate inside the trough.

A 1 ¼” access hole must be drilled (¾”

in front of the bracket and 7/8” from

the top of the trough)

reinforcement plate through. Use

3/8” x 1 ¼” bolts, flat washers and lock

washers to secure the bracket. A

plastic plug is supplied to cover the

access hole.

4. Fasten the main hoop to the

mounts using 3/8” x 1” Socket Head

nd lock washers

5. Secure the lower portion of the

bracket to the floor pan with two 3/8” x

1 ¼” bolt, flat washers and Nylok nuts.

Another reinforcement plate will be

installed under the car. It will also

meet up with the pinch weld.

re 3/8” holes must be

drilled through the pinch weld. 3/8” x

1” bolts, flat washers and Nylok nuts

will be used here.

to slide the

Cap Screws a

6. Two mo

.

7. In order to keep the “T” in the
casting facing up, and the bolts facing
the correct direction, there are two
different direction clamps. Be very
careful as to which clamp halves you
are bolting together. Refer to the
image on page 6 for clamp locations.

8. A correctly assembled clamp
should look like the one in the picture
shown to the left; there should be a

gap on one side for the tab to slide
into.

9. The next bar to be installed is the
package tray bar.

10. Before installing the bar, use the
template on page 7 to drill four holes
in the top of the package tray for the
bar flange to bolt to.

11. Fasten the clamp to the main
hoop with the tab facing rearward.
Use clamp D on the driver side and
clamp P on the passenger side.

12. The other end of the bar will
attach to the top of the package tray.
Drop four 3/8” x 1 ¼” bolts with flat
washers down through the package
tray.

13. The long opening next to the
drilled holes has a lip that will interfere
with the trunk bar mount. The lip must
be flattened; this can be done with a
pair of pliers.

14. Bolt the trunk bar mount up to the
package tray, use 3/8” Nylok nut and
flat washers to secure the assembly.

15. Two 3/8” holes must be drilled
through the vertical plane of the
package tray to install the
reinforcement plate. These holes
must be drilled from the trunk.
Secure the plate with two 3/8” x 1 ¼”
bolts, flat washers and Nylok nuts.

16. The other end of the trunk bar will
attach to the trunk floor, straddling the
frame rail.

17. Two more reinforcement plates
will be installed under the car, one on
each side of the frame rail. Six 3/8” x
1 ¼” bolts, flat washers and Nylok
nuts will be used.

TigerClamp Location Chart

Package Tray Bar Template