Ricon 10-305 Operator's Manual

Download

10-305

10” Woodworking Bandsaw

Operator’s Manual

Record the serial number and date of purchase in your manual for future reference.

Serial Number: _________________________ Date of purchase: _________________________

For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167

10-305M4

4001824

www.rikontools.com

TABLE OF CONTENTS

Specications.....................................................................................................................2

Safety Instructions ........................................................................................................3 - 6

Contents of Package ....................................................................................................7

Assembly .........................................................................................................................7 - 8

Getting To Know Your Bandsaw .........................................................................................8

Adjustments...............................................................................................................9 - 11

Operation ..................................................................................................................11

Maintenance ....................................................................................................................11

Wiring Diagram ................................................................................................................12

Troubleshooting ........................................................................................................12 - 15

Parts Diagrams & Parts Lists ..................................................................................16 - 19

Notes ...............................................................................................................................20

Accessories .............................................................................................................................21

How To Guide for all Band Saw Blades ................................................................................22

Warranty ..........................................................................................................................23

SPECIFICATIONS

Motor .............................................................................................1/3 HP

Motor Speed (no load).............................................................1720 RPM

Volts ............................................................................................... 110 V

Amps, Hertz .........................................................................3.5 A, 60 Hz

Blade Length ............................................................. 70-1/2” (1791 mm)

Blade Width ....................................................1/8” - 1/2” (3.2 - 12.7 mm)

Blade Speed ..........................................................................2780 ft/min

Table Size ....................................12-1/2” x 13-3/4” (318 mm x 349 mm)

Table Tilt .............................................................................. Right 0 - 45

Maximum Cutting Width (throat) ....................................9-5/8” (245 mm)

Maximum Cuttng Depth (height) ....................................4-5/8” (118 mm)

Table Height .................................................................14-1/2” (368 mm)

Fence Height ..........................................................................2” (51 mm)

Fence Length .............................................................. 13-1/2” (343 mm)

Dust Port ............................................................. 2-1/2” Diameter (O.D.)

Overall Size ......................33-3/4” x 21” x 15-1/4” (857 x 533 x 387 mm)

Base Size ..............................................9-1/4” x 15-3/4” (236 x 400 mm)

Net Weight ......................................................................... 68 lbs (31 kg)

SAFETY INSTRUCTIONS

IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following

instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, re,

and/or serious personal injury. There are certain applications for which this tool was designed. We strongly recommend that this tool not be modied and/ or used for any other application other than that for which it was designed. If you have any questions about its application, do not use the tool until you have contacted us and we have advised you.

SAFETY SYMBOLS

SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION. This symbol may be used in

conjunction with other symbols or pictographs.

Indicates an imminently hazardous situation, which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation, which, if not avoided, could result in minor or moderate injury.

NOTICE: Shown without Safety Alert Symbol indicates a situation that may result in property damage.

GENERAL SAFETY

KNOW YOUR POWER TOOL. Read the owner’s manual

carefully. Learn the tool’s applications, work capabilities, and its specic potential hazards.

BEFORE USING YOUR MACHINE

To avoid serious injury and damage to the tool, read and follow all of the Safety and Operating Instructions before operating the machine.

1. Some dust created by using power tools contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement, and other

• masonry products.

• Arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment, such as those dust masks that are specially designed to lter out microscopic particles.

2. READ the entire Owner’s Manual. LEARN how to use the tool for its intended applications.

3. GROUND ALL TOOLS. If the tool is supplied with a 3 prong plug, it must be plugged into a 3-contact electrical receptacle. The 3rd prong is used to ground the tool and provide protection against accidental electric shock. DO NOT remove the 3rd prong. See Grounding Instructions on the following pages.

4. AVOID A DANGEROUS WORKING ENVIRONMENT. DO NOT use electrical tools in a damp environment or

expose them to rain.

5. DO NOT use electrical tools in the presence of ammable liquids or gasses.

6. ALWAYS keep the work area clean, well lit, and organized. DO NOT work in an environment with oor surfaces that are slippery from debris, grease, and wax.

7. KEEP VISITORS AND CHILDREN AWAY. DO NOT permit people to be in the immediate work area, especially when the electrical tool is operating.

8. DO NOT FORCE THE TOOL to perform an operation for which it was not designed. It will do a safer and higher quality job by only performing operations for which the tool was intended.

9. WEAR PROPER CLOTHING. DO NOT wear loose clothing, gloves, neckties, or jewelry. These items can get caught in the machine during operations and pull the operator into the moving parts. The user must wear a protective cover on their hair, if the hair is long, to prevent it from contacting any moving parts.

10. CHILDPROOF THE WORKSHOP AREA by removing switch keys, unplugging tools from the electrical receptacles, and using padlocks.

11. ALWAYS UNPLUG THE TOOL FROM THE ELECTRICAL RECEPTACLE when making adjustments, changing parts or performing any maintenance.

SAFETY INSTRUCTIONS

12. KEEP PROTECTIVE GUARDS IN PLACE AND IN WORKING ORDER.

13. AVOID ACCIDENTAL STARTING. Make sure that the power switch is in the “OFF” position before plugging in the power cord to the electrical receptacle.

14. REMOVE ALL MAINTENANCE TOOLS from the immediate area prior to turning “ON” the machine.

15. USE ONLY RECOMMENDED ACCESSORIES. Use of incorrect or improper accessories could cause serious injury to the operator and cause damage to the tool. If in doubt, check the instruction manual that comes with that particular accessory.

16. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to the “OFF” position. DO NOT leave the tool until it has come to a complete stop.

17. DO NOT STAND ON A TOOL. Serious injury could result if the tool tips over, or you accidentally contact the tool.

18. DO NOT store anything above or near the tool where anyone might try to stand on the tool to reach it.

19. MAINTAIN YOUR BALANCE. DO NOT extend yourself over the tool. Wear oil resistant rubber soled shoes. Keep oor clear of debris, grease, and wax.

20. MAINTAIN TOOLS WITH CARE. Always keep tools clean and in good working order. Keep all blades and tool bits sharp, dress grinding wheels and change other abrasive accessories when worn.

21. EACH AND EVERY TIME, CHECK FOR DAMAGED PARTS PRIOR TO USING THE TOOL. Carefully check all guards to see that they operate properly, are not damaged, and perform their intended functions. Check for alignment, binding or breaking of moving parts. A guard or other part that is damaged should be immediately repaired or replaced.

22. DO NOT OPERATE TOOL WHILE TIRED, OR

UNDER THE INFLUENCE OF DRUGS, MEDICATION OR ALCOHOL.

23. SECURE ALL WORK. Use clamps or jigs to secure the workpiece. This is safer than attempting to hold the workpiece with your hands.

24. STAY ALERT, WATCH WHAT YOU ARE DOING,

AND USE COMMON SENSE WHEN OPERATING A POWER TOOL.

A moment of inattention while operating power tools may result in serious personal injury.

25. ALWAYS WEAR A DUST MASK TO PREVENT

INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust

and asbestos dust. Direct particles away from face and body. Always operate tool in well ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly tting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.

26. USE A PROPER EXTENSION CORD IN GOOD CONDITION. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. The table on the following page shows the correct size to use depending on cord length and nameplate amperage rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the larger diameter of the extension cord. If in doubt of the proper size of an extension cord, use a shorter and thicker cord. An undersized cord will cause a drop in line voltage resulting in a loss of power and overheating.

USE ONLY A 3-WIRE EXTENSION CORD THAT HAS A 3-PRONG GROUNDING PLUG AND A 3-POLE RECEPTACLE THAT ACCEPTS THE TOOL’S PLUG.

27. ADDITIONAL INFORMATION regarding the safe and proper operation of this product is available from:

• Power Tool Institute 1300 Summer Avenue Cleveland, OH 44115-2851 www.powertoolinstitute.org

• National Safety Council 1121 Spring Lake Drive Itasca, IL 60143-3201 www.nsc.org

• American National Standards Institute 25 West 43rd Street, 4th Floor New York, NY 10036 www.ansi.org

• ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor regulations www.osha.gov

28. SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others.

SAFETY INSTRUCTIONS

ELECTRICAL SAFETY

THIS TOOL REQUIRES A 3-PRONG 110V RECEPTICAL, AND MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC SHOCK.

IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,

grounding provides the path of least resistance for electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor. The plug MUST be plugged into a matching electrical receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.

DO NOT MODIFY ANY PLUG. If it will not t the electrical receptacle, have the proper electrical receptacle installed by a qualied electrician.

EXTENSION CORDS

Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool.

Check extension cords before each use. If damaged replace immediately. Never use a tool with a damaged cord, since touching the damaged area could cause electrical shock, resulting in serious injury.

Use a proper extension cord. Only use cords listed by Underwriters Laboratories (UL). Other extension cords can cause a drop in line voltage, resulting in a loss of power and overheating of tool. When operating a power tool outdoors, use an outdoor extension cord marked “W-A” or “W”. These cords are rated for outdoor use and reduce the risk of electric shock.

IMPROPER ELECTRICAL CONNECTION of the equipment grounding conductor can result in risk of electric shock. The conductor with the green insulation (with or without yellow stripes) is the equipment grounding conductor. DO NOT connect the equipment grounding conductor to a live terminal if repair or replacement of the electric cord or plug is necessary.

CHECK with a qualied electrician or service personnel if you do not completely understand the grounding instructions, or if you are not sure the tool is properly grounded when installing or replacing a plug.

USE ONLY A 3-WIRE EXTENSION CORD THAT HAS A 3-PRONG GROUNDING PLUG AND A 3-POLE RECEPTACLE THAT ACCEPTS THE TOOL’S PLUG. *

REPLACE A DAMAGED OR WORN CORD IMMEDIATELY.

This tool is intended for use on a circuit that has a 110 volt electrical receptacle. FIGURE 1 shows the type of the 110v, 3-wire electrical plug and electrical receptacle that has a grounding conductor that is required.

THIS SYMBOL DESIGNATES THAT THIS TOOL IS LISTED BY THE INTERTEK TESTING SERVICES, TO UNITED STATES AND CANADIAN STANDARDS.

Sample of 110 volt plug required for this machine.

* Canadian electrical codes require extension cords to

be certied SJT type or better.

** The use of an adapter in Canada is not acceptable.

Figure 1

SAFETY INSTRUCTIONS

SPECIFIC SAFETY INSTRUCTIONS FOR BAND SAWS

1. Always allow the bandsaw blade to stop before removing scrap pieces from table.

2. Always keep hands and ngers away from the blade.

3. Never attempt to saw stock that does not have a at surface, unless a suitable support is used.

4. Always hold material rmly and feed it into the blade at a moderate speed.

5. Always turn off the machine if the material is to be backed out of an uncompleted cut.

6. Adjust the upper guide about 1/8” to 1/4” above the material being cut.

7. Check for proper blade size and type for thickness and type of material being cut.

8. Make sure that the blade tension and blade tracking are properly adjusted.

9. Make “relief” cuts before cutting long curves.

10. Release blade tension when the saw will not be used for a long period of time.

California Proposition 65 Warning

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially designed to lter out microscopic particles.

For more detailed information about California Proposition 65 log onto rikontools.com.

This owner’s manual is not a teaching aid. Use of this owner’s manual is intended to

show assembly, adjustments, and general use.

SAVE THESE INSTRUCTIONS.

Refer to them often.

NOTE: The specications, photographs, drawings and information in this manual represent the current

model when the manual was prepared. Changes and improvements may be made at any time, with no obligation on the part of Rikon Power Tools, Inc. to modify previously delivered units. Reasonable care has been taken to ensure that the information in this manual is correct, to provide you with the guidelines for the proper safety, assembly and operation of this machine.

ASSEMBLY

10-305

www.rikontools.com

10-305M4

10” Woodworking Bandsaw

Operator’s Manual

Record the serial number and date of purchase in your manual for future reference.

Serial Number: _________________________ Date of purchase: _________________________

For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167

4001824

1. TOOLS REQUIRED FOR ASSEMBLY

Item Description Qty.

Medium Screwdriver..............................1

Adjustable Wrench.................................1

Square ...................................................1

2. UNPACKING AND CHECKING CONTENTS

The 10-305 10” Bandsaw is shipped complete in one box.

a. Separate all parts from carton and check each item with “Table of Carton Contents” to make sure all items are accounted for, before discarding any packing material.

b. Remove the protective oil that is applied to the table. Use any ordinary house hold type grease and spot remover.

c. Apply a coat of paste wax to the table to prevent rust. Wipe all parts thoroughly with a clean dry cloth.

LIST OF LOOSE PARTS IN BAG

Item Description Qty

Blade Tension Knob.........................................1

Hex. Socket Head Cap Screw M6x30...............1

Washer 6.........................................................1

Wing Nut M6....................................................1

Hex. Bolt M6x12..............................................4

Lock Washer 6.................................................4

CARTON CONTENTS

Item Description Qty

A Main Machine...............................................................1

B Fence.............................................................1

C Table...................................................................1

D Guide Rail..................................................1

E Manual..............................................................1

F Upper Table Trunnion Assembly........................................1

G Bag of Loose Parts........................................................1

Star Knob Screw...............................................2

Washer 6 .........................................................2

M3 Hex “L” Wrench..........................................1

M5 Hex “L” Wrench...........................................1

2. INITIAL ASSEMBLY

The machine is supplied partly assembled. Prior to use, the following items have to be installed: Table, Blade Tension Knob and Rip Fence.

WARNING: To Avoid injury, do not attempt to run or use this ma-

chine until all parts are assembled and working properly.

a. Assemble the upper table trunnion to the lower table trunion with Carriage Bolt, Glide Piece, Washer and Wing Nut. Place the table

on to the upper table trunnion, taking care when passing the saw blade through the slot of the table (See Fig. 1). Locate four hex bolts and four lock washers from the bag of loose parts. Mount the table to the upper table trunnion and install a bolt with washer in each hole, then tighten with adjustable wrench.

FIG. 1

d. Place the blade tension knob on to the blade tensioner located at the top of the frame (See Fig. 4).

Blade Tension Knob

b. Fasten the guide rail with two each star knob screw and washer to the table. Use the hex socket head cap screw, washer and wing nut for correcting the working table atness. (See Fig. 2)

FIG. 2

c. Lay the rip fence onto the guide rail. Adjust the rip fence parallel to the saw blade. Tighten rip fence handle by pressing downward. (See Fig. 3)

FIG. 4

e. To ensure sufcient upright stability of the machine it should be bolted to oor, bench or worktable. For this purpose 6mm holes are provided in the machine’s base. (See Fig. 5)

FIG. 5

f. The bandsaw has a 2-1/2” dust port included. (See Fig. 6) It is recommended that when in use, the bandsaw is connected to a suitable dust collector.

Lock switch

Guide rail

FIG. 3

GETTING TO KNOW YOUR BANDSAW

Blade tension knob

Door locking knob

Guide post locking knob

Blade guide

Upper table trunnion

Lower table trunnion

Dust port

FIG. 6

Blade tracking knob

Guide post adjusting knob

Fence

Motor

ADJUSTMENT

1. CENTERING THE TABLE

a. Loosen the four hex. bolts mounting the table to the upper table trunnion. (See Fig. 7)

Hex. bolt

FIG. 7

b. Move the table sideways as required, until the saw blade runs through the center of the table insert. c. If the adjustment of “b” is not enough to center the table, loosen the four ange nuts holding the lower table trunnion and move the table sideways to place the table in the center. d. Re-tighten hex. bolts for trunnion, recheck the saw blade position.

2. SETTING TABLE SQUARE TO SAW BLADE

Loosen the wing nut on the lower table trunnion and place a suitably sized square against the saw blade. If the table requires adjustment, proceed as follows:

a. Using a wrench, release the hex. nut on the frame. (See Fig.8) b. Place the wrench on the hex. bolt and adjust until the table square to the saw blade.(See Fig.8)

3. TILTING THE TABLE

For bevel cuts, the table tilts 0 through 45 degrees.

a. To tilt the table, loosen the wing nut on the table trunnion, set the table to the required angle and tighten the wing nut again (Fig. 10).

Wing nut

FIG. 10

b. It is recommended to verify the correct angle setting using an angle guide, or by making trial cuts in scrap wood. Adjust the indicator accordingly by using a phillips head screwdriver.

4. ADJUSTING THE RIP FENCE

The locking pressure of the rip fence has been factory-set, if adjustment is required proceed as follows:

a. Raise the fence handle to horizontal position. b. Turn the fence handle clockwise to increase clamping pressure, counterclockwise to decrease clamping pressure.(See Fig. 11) c. After counterclockwise truning the fence handle, sliding the rip fence to the desired position on the guide rail.(See Fig. 11) d. The fence handle has a cam action, press down the handle to clamp tightly to the table after setting rip fence to desired position.

Square

Hex. bolt

Hex. nut

c. Tighten the hex nut and check the blade and table for squareness. d. Lock the table into position and check that the indicator reads zero degree on the side of lower table trunnion. Loosen the screw securing the indicator and reset if necessary to give zero degree reading. (See Fig. 9)

FIG. 8

FIG. 9

Fence handle

FIG. 11

NOTE: Do not adjust the fence handle such that excessive pres-

sure is exerted during operation - this may lead to deformation of the end clamp at the rear of the rip fence. Set the fence handle to apply just enough pressure to enable safe operation during cutting.

5. CHANGING AND ADJUSTING THE SAW BLADE

This bandsaw is factory-equipped with a general-purpose wood cutting blade, the saw blade is set prior to delivery. To change the saw blade, the following procedure must be followed:

WARNING: To avoid injury from unexpected starting, whenever

changing the saw blade or carrying out adjustments, switch the bandsaw off and remove the power cord from the main outlet. To avoid injury to hands when handling the saw blade, wear gloves whenever necessary.

a. Remove the rip fence, the guide rail, the wing nut and screw from the table. b. Open the upper and lower doors by turning the door locking knobs.

c. Loosen the blade tension by turning the blade tension knob on the top of the upper wheel housing counterclockwise until the saw blade has slackened (viewed from above) (See Fig. 12).

c. Set the blade guide to the required height by turning the guide post adjusting knob. d. Tighten the wing nut after setting.

Guide post adjusting knob

Wing nut

FIG. 14

FIG. 12

d. Remove the saw blade from the upper and lower wheels. e. When tting the new saw blade ensure the blade teeth are pointing downwards and towards you at the position where the saw blade passes through the table. f. Re-tension the new saw blade and check the saw blade tracking by turning the upper wheel by hand. The saw blade should run in the center of the bandsaw wheels. g. If need adjust the tracking of the saw blade, proceed as mentioned below “ TRACKING THE SAW BLADE” h. Replace the rip fence, the guide rail, the wing nut and screw to the table. i. Close the upper and lower doors by turning the door locking knobs before reconnecting the power supply.

6. TRACKING THE BANDSAW BLADE

Set the tracking of the saw blade before setting the blade guides. Once the saw blade is installed and tensioned, track the saw blade by adjusting the tracking knob by hand (See Fig. 13). The saw blade should run in the center of the bandsaw wheels. When the correct adjustment is achieved lock the tracking knob with the wing nut.

8. ADJUSTING THE BLADE GUIDES

The Upper Blade Guide

a. To adjust the upper blade guides, rst position the right and left roller guides relative to the blade by slackening the ratcher handle Fig.15 and moving the guide carrier until both roller guides are approximately 1/16” behind the gullets of the saw blade.

b. Set both roller guides to within 1/32” of the saw blade by releasing the guide adjusting screw, (A) Fig. 15, on each side of the saw blade. Do not set the roller guides too close as this will adversely affect the life of the saw blade.

c. Adjust the rear roller guide to be just clear of the back of the saw blade by unlocking the guide adjusting screw (B) Fig. 15

d. When the correct adjustment is reached, lock the rear roller guide in position with the guide adjusting screw (B) Fig.15

Ratchet handle

Guide adjusting

screw (B)

Wing nut

Tracking knob

FIG. 13

7. SETTING THE CUTTING HEIGHT

a. The upper blade guide should be set as close as practical against the workpiece. b. To adjust this height, loosen the wing nut at the side of the upper wheel housing. (See Fig. 14)

Guide adjusting screw (A)

FIG. 15

The Lower Blade Guide

a. To adjust the lower blade guides, rst position the right and left roller guides relative to the blade by slackening the lock nut Fig.16 and moving the guide carrier until both roller guides are approximately 1/16” behind the gullets of the saw blade

b. Set both roller guides to within 1/32” of the saw blade by releasing the guide adjusting screw (C) Fig. 16 on each side of the saw blade. Do not set the roller guides too close as this will adversely affect the life of the saw blade.

c. Adjust the rear roller guide to be just clear of the back of the saw blade by unlocking the guide adjusting screw. (D) Fig. 16

d. When the correct adjustment is reached, lock the rear roller guide in position with the guide adjusting screw. (D) Fig.16

Lock nut

Guide adjusting screw (D)

Guide adjusting

screw (C)

FIG. 16

9. CHANGING THE DRIVE BELT TENSION

a. Release the saw blade tension by turning the blade tension knob on the top of bandsaw counterclockwise. b. Using a M6 hex. “L” wrench (not provided) to release the hex. socket head cap screw on motor mounting ange. (See Fig. 17)

OPERATION

WARNING: Before starting check if any part of your bandsaw is

missing, malfuctioning, has been damaged or broken... such as the motor switch, or other operation control, a safety device or the power cord, turn the bandsaw off and unplug it until the particular part is properly repaired or replaced.

The saw blade cuts on a continuous downstroke. To avoid injury when hands are unavoidably near to the saw blade, they should be placed on either side of the blade, not in line with it. Use a push stick whenever possible when working in close proximity to the saw

blade.

Hex. socket head cap screw

FIG. 17

c. Tension the drive belt until there is 3/8” to 1/2” of deection. d. Follow procedures for CHANGING AND ADJUSTING THE SAW BLADE & TRACKING THE BANDSAW BLADE, before restoring power to the bandsaw and setting up for use.

For best results the saw blade must be sharp. Select the right saw blade for the job, depending on the thickness of the wood the cut to be made. The thinner and harder the wood, the ner the teeth of the saw blade. Use a ne tooth blade for cutting sharp curves.

The machine is especially suited for cutting curves, but will also make straight cuts. Do not attempt to turn the workpiece without pushing it, as this may cause the workpiece to get stuck, or the saw blade to bend.

The rip fence is to enable safe and accurate straight cuts of the workpiece, usually in the same direction as the grain of the timber.

Start the bandsaw by turning the lock switch on and wait for the

bandsaw to come to full speed before starting to cut. Never start the bandsaw with the workpiece in contact with the saw blade.

Slowly feed the workpiece towards the saw blade, putting only light pressure on it. With both hands, rmly hold the workpiece down on the table, and feed it towards the saw blade slowly.

MAINTENANCE

WARNING: To avoid injury due to unexpected starting, before

cleaning or carrying out maintenance work, switch off and disconnect the bandsaw from the power source.

Never use water or other liquids to clean the bandsaw. Use a dry brush.

Regular maintenance of the bandsaw will prevent unnecessary problems.

A miter gauge (available separately) is to enable safe and accurate crosscut of the workpiece.

The tiltable table is used for bevel cuts.

WARNING: When sawing with the rip fence and a tilted table, the rip fence must be installed on that side of the table which is tilted downward.

a. Keep the table clean to ensure accurate cutting. b. Keep the outside of the machine clean to ensure accurate operation of all moving parts and prevent excessive wear. c. Keep the ventilation slots of the motor clean to prevent it from overheating. d. Keep the inside (near the saw blade, etc.) clean to prevent accumulation of dust. Use dust collection if possible. e. To prolong the life of the saw blade, when the bandsaw is not in use for extended periods, release the saw blade tension. Before reusing the bandsaw ensure that the blade is re-tensioned and tracking is checked.

ELECTRICAL SCHEMATIC

WARNING: This machine must be grounded. To avoid electrocution or re, any repairs to electrical system should be done only by a

qualied electrician, using genuine replacement parts.

TROUBLESHOOTING

Problem Diagnosis Remedy

The machine does not work when switched on.

The saw blade does not move with the motor running.

The saw blade does not cut in a straight line.

The saw blade does not cut, or cuts very slowly.

Sawdust builds up inside the machine. This is normal Clean the machine regularly. Open the

1. No power supply.

2. Defective switch. 3 Defective motor.

1. The blade tension knob has not been tightened.

2. The blade has come off one of the wheels.

3. The saw blade has broken.

4. The drive belt has snapped.

1. Rip fence for cutting not used.

2. Feed rate too fast.

3. The blade teeth are dull or damaged.

4. Blade guides not suitably adjusted.

1. The teeth are dull, caused by cutting hard material or long use.

2. The saw blade was tted the wrong way on the bandsaw.

1. Check the cable for breakage.

2. Replace the lock switch.

3. Defective motor.

1. Switch off the motor, tighten the blade tension knob.

2. Open the doors and check.

3. Replace the blade.

4. Replace the belt.

1. Use a rip fence.

2. Put light pressure on the workpiece. Make sure the saw blade does not bend.

3. Try a new saw blade.

4. Adjust the blade guides (see ADJUSTMENT instructions).

1. Replace the saw blade, use a 6 T.P.I. saw blade for wood and soft material. Use a 14 T.P.I. saw blade for harder materials. A 14 T.P.I. saw blade always cuts slower due to the ner teeth and the slower cutting performance.

2. Fit the saw blade correctly.

doors and remove the sawdust with a vacuum cleaner.

Sawdust inside the motor housing. This is normal Clean the ventilating slots of the motor

The machine does not cut at 45 or 90

degrees.

1. The table is not at right angles to the blade.

2. The saw blade is dull or too much pressure was put on the workpiece.

with a vacuum cleaner. From time to time remove the sawdust to prevent it from being drawn into the housing.

1. Adjust the table.

2. Replace the saw blade or put less pressure on the workpiece.

TROUBLESHOOTING

CHANGING THE MOTOR DRIVE BELT

(Refer to parts diagram on page 16)

Before changing the belt, make sure that the bandsaw is unplugged from the power source.

Release the saw blade tension from the drive belt by turning the tension knob (Part #16) counter clockwise on top of the saw.

Release the drive belt tension by loosening the Hex. Socket Head Cap Screw M8x30 (Part #125) on the motor located at the rear of the saw. . Remove the lower wheel (Wheel Assembly, Part #138) by removing the retaining ring (Part #140) in the middle of the wheel’s hub. Carefully slide the lower wheel off of the lower wheel shaft, and at the same time remove the saw blade from this wheel.

Remove the old drive belt from the wheel’s pulley, and install the new belt. Make sure that the ribs in the drive belt are seated correctly in the pulley before reassembling and tensioning the drive belt.

Reverse the procedure to re-assemble the saw parts. Tension the drive belt until there is 3/8” to 1/2” of deection.

CHANGING BANDSAW TIRES

Use a putty knife to get underneath the tire and pull it up and away from the wheel. Work the putty knife all the way around the wheel to loosen the tire. Then, use the putty knife as leverage to ip the tire over and off of the wheel. Clean the inside of the groove, removing any dirt, debris or cement with lacquer thinner.

Soak the replacement tire in warm water to make it more exible. Dry the tire, and while it is still warm, lay it on top of the wheel. Start by setting the tire into the wheel groove at the top of the wheel. Using a putty knife, work the new tire around the wheel, making sure not to slice the tire. If rubber cement is to be used as a binder, make sure to distribute it evenly. Having high spots between the wheel and the tire will cause a vibration and effect blade tracking.

TROUBLESHOOTING

LOWER WHEEL ADJUSTMENTS

The following instructions will correct common blade issues related to the lower wheel’s alignment in relation to the upper wheel. These adjustments will correct the blade position on the lower wheel and blade oscillation (wobble). These are critical adjustments which affect the performance and accuracy of the bandsaw.

PLEASE READ AND UNDERSTAND THESE STEPS THOROUGHLY BEFORE

MAKING ANY ADJUSTMENTS. FAILURE TO DO SO COULD DAMAGE THE MACHINE.

Please contact a tech support representative if you have questions before attempting these adjustments. RIKON Tech Support 877-884-5167 techsupport@rikontools.com

Release the blade tension completely before making any lower wheel adjustments. Pressure must be released on the lower wheel to allow proper adjustments and to avoid damaging the machine.

If the blade is not running true, or it is not running on center of the lower wheel but is correct on the upper wheel, then an adjustment to the wheel hub on the rear of the bandsaw is required.

The numbers shown on the rear hub photo represent the positions on a clock face.

If a blade is tracking forward on the lower wheel toward the door, follow these correction steps:

1.) De-tension the saw blade.

2.) Loosen 9 o’clock shaft bolt to take pressure off the shaft.

3.) Loosen 12 o’clock shaft bolt one half rotation.

4.) Tighten the 6 o’clock shaft bolt until the shaft touches the 12 o’clock adjusting bolt.

5.) Lock all three shaft bolts.

6.) Re-tension the saw blade and set the upper wheel to plumb by adjusting the tracking knob. Spin the upper wheel by hand and track the blade.

7.) Repeat if further adjustment is necessary.

Incorrect

Correct

TROUBLESHOOTING

If a blade is tracking on the rear of the lower wheel, away from the door, follow these steps:

1.) De-tension the saw blade.

2.) Loosen 9 o’clock shaft bolt to take pressure off the shaft.

3.) Loosen 6 o’clock shaft bolt one half rotation.

4.) Tighten the 12 o’clock shaft bolt until the shaft touches the 6 o’clock adjusting bolt.

5.) Lock all three shaft bolts.

6.) Re-tension the saw blade and set the upper wheel to plumb by adjusting the tracking knob. Spin the upper wheel by hand and track the blade.

7.) Repeat if further adjustment is necessary.

Incorrect Correct

If a blade is moving back and forth (wobbling) follow these steps:

Adjustment to the wheel hub on the rear of the bandsaw is required.

1.) De-tension the saw blade.

2.) Loosen 6 o’clock shaft bolt to take pressure off of the shaft.

3.) Loosen 9 o’clock shaft bolt one half rotation.

4.) Tighten the 3 o’clock shaft bolt until the shaft touches the 9 o’clock adjusting bolt.

5.) Lock all three shaft bolts.

6.) Re-tension the saw blade and set the upper wheel to plumb by adjusting the tracking knob. Spin the upper wheel by hand and track the blade.

7.) Start the bandsaw and check blade movement.

8.) If movement has diminished then continue with the adjustment.

9.) If movement is worse, reverse the adjustments in steps 3 and 4.

Back and forth

movement.

PARTS DIAGRAM

PARTS LIST

KEY NO. DESCRIPTION MFG. PART NO.

15 16 17

20 21 22

25 26 27

29 30 31 32 33 34 35 36 37 38 39

40 41 42

45 46 47

Rivet 4x8 Leaf Spring Blade Tension Knob Cap Blade Tension Knob Body Blade Tensioner Washer 8 Flange Nut M6 Carriage Bolt M8x50 Bushing Ring Top Plug Frame Hex. Bolt M6x12 Lock Nut M6 Washer 6 Gear Special Spring Washer 8 Tube Plastic Nut M20 Adjusting Knob Body Adjusting Knob Cap Blade Tracking Knob Cap Blade Tracking Knob Body Hex. Bolt M6x60 Hex. Nut M6 Wing Nut M6 Washer 6 Tapping Screw ST3.5x13 Rack Slider Carriage Bolt M8x20 Bolt Guide Wing Nut M8 Blade Guide T-nut M6 Hex. Bolt M6x10

P10-305-9 P10-305-10 P10-305-15 P10-305-16 P10-305-17 P10-305-18 P10-305-19 P10-305-20 P10-305-21 P10-305-22 P10-305-23 P10-305-24 P10-305-25 P10-305-26 P10-305-27 P10-305-28 P10-305-29 P10-305-30 P10-305-31 P10-305-32 P10-305-33 P10-305-34 P10-305-35 P10-305-36 P10-305-37 P10-305-38 P10-305-39 P10-305-40 P10-305-41 P10-305-42 P10-305-43 P10-305-44 P10-305-45 P10-305-46 P10-305-47

KEY NO. DESCRIPTION MFG. PART NO.

49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79

80 81 82

T-nut M6 Washer 6 Hex. Socket Set Screw M6x25 Ratchet handle Guide Adjust Screw Ball Bearing 6mm Washer 6 Bearing Mount Cylinder Hex. Socket Set Screw M6x10 Upper Guide Mount Upper Guide Shaft Bearing Mount Cylinder w/Cap Upper Guide Body Carriage Bolt M6x30 Glide Piece Upper Table Trunion Lock Washer 6 Hex. Bolt M6x12 Lower Table Trunion Carriage Bolt M6x16 Wing Nut M6 Washer 6 Flange Nut M6 Indicator Tapping Screw ST3.5x9.5 Table Table Insert Hex. Socket Head Cap Scr M6x30 Washer 6 Wing Nut M6 Fence Clamper Threaded Rod Spring Rod Guide Fence

P10-305-48 P10-305-49 P10-305-50 P10-305-51 P10-305-52 P10-305-53 P10-305-54 P10-305-55 P10-305-56 P10-305-57 P10-305-58 P10-305-59 P10-305-60 P10-305-61 P10-305-62 P10-305-63 P10-305-64 P10-305-65 P10-305-66 P10-305-67 P10-305-68 P10-305-69 P10-305-70 P10-305-71 P10-305-72 P10-305-73 P10-305-74 P10-305-75 P10-305-76 P10-305-77 P10-305-78 P10-305-79 P10-305-80 P10-305-81 P10-305-82

NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts.

For Parts under Warranty, the serial number of your machine is required.

PARTS DIAGRAM

PARTS LIST

KEY NO. DESCRIPTION MFG. PART NO.

85 86 87

89 90 91 92 98 99

100 101 102

103

104

105 106 107

108

109

110

115 116 117 125 126 127

128 128A

129 130 131 132 133 134

Flat Countersunk Scr M6x10 Rod Guide Guide Rail Fence Carrier Special Screw Washer 10 Fence Handle Roll Pin 3x18 Star knob screw Washer 6 Bearing Mount Cylinder Hex. Socket Set Screw M6x10 Lower Guide Body Lower Guide Shaft Lower Guide Mount Lock Nut M6 Washer 6 Washer 6 Hex. Bolt M6x20 Guide Adjust Screw Ball Bearing 6mm Guide Key Washer 6 Lower Door Leaf Spring Rivet 4X8 Hex. Socket Hd Cap Scr M8x30 Spring Washer 8 Washer 8 Motor Motor Capacitor (not shown) Hex. Bolt M6x20 Hex. Nut M6 Lower Bearing Bolt Hex. Nut M14 Motor Pulley Hex. Socket Set Scr M6x10

P10-305-83 P10-305-84 P10-305-85 P10-305-86 P10-305-87 P10-305-88 P10-305-89 P10-305-90 P10-305-91 P10-305-92 P10-305-98 P10-305-99 P10-305-100 P10-305-101 P10-305-102 P10-305-103 P10-305-104 P10-305-105 P10-305-106 P10-305-107 P10-305-108 P10-305-109 P10-305-110 P10-305-115 P10-305-116 P10-305-117 P10-305-125 P10-305-126 P10-305-127 P10-305-128 P10-305-128A P10-305-129 P10-305-130 P10-305-131 P10-305-132 P10-305-133 P10-305-134

KEY NO. DESCRIPTION MFG. PART NO.

135 136 137 138 139

140 141 142

143

144

145 146 147

148

149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170

Drive Belt Ball Bearing 12mm Retaining Ring 28 Lower Wheel Tire Retaining Ring 12 Saw Blade Upper Wheel Upper Bearing Bolt Wheel Carrier Bracket Hex. Nut M14 Star Lock Mount Shaft Blade Tensioner Carriage Bolt M8x65 Brush Strip Flange Nut M8 Hex. Bolt M6x35 Hex. Nut M6 Cable w/Plug Lock Washer 4 Washer 4 Pan Head Screw M4x8 Switch Cover Plate Lock Switch Pan Head Screw M4x12 Tension Bracket Rubber Tube Washer 8 Nut Bushing Hex Screw Upper Door Hex Screw Handle Lower Door

P10-305-135 P10-305-136 P10-305-137 P10-305-138 P10-305-139 P10-305-140 P10-305-141 P10-305-142 P10-305-143 P10-305-144 P10-305-145 P10-305-146 P10-305-147 P10-305-148 P10-305-149 P10-305-150 P10-305-151 P10-305-152 P10-305-153 P10-305-154 P10-305-155 P10-305-156 P10-305-157 P10-305-158 P10-305-159 P10-305-160 P10-305-161 P10-305-162 P10-305-163 P10-305-164 P10-305-165 P10-305-166 P10-305-167 P10-305-168 P10-305-169 P10-305-170

NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts.

For Parts under Warranty, the serial number of your machine is required.