Ricoh RH 100 User Manual

Page 1
Quick Guide
This guide describes the basic printing procedures using the printer and this machine. In the next pages, the procedures for each step and particular cautions are explained. For safe and correct use, be sure to read Safety Information before using the machine.
Guide to Components of the Finisher
Cassette
Front Cover
DSA121
Mode Switching Lever
Control Panel
Mode indicator
*1
• Light: Press the [Preheat] key to start preheating
• Flashing: Preheating under way
• Off: Preheating completed
Time/temperature indicator [Temperature] key [Preheat] key
Finisher (This machine Rh 100)
*1
[Fixing Time] key [Stop/Unlock] key
[Power] key
DSB130
Page 2
1
Loading the fabric in the cassette
For details, refer to User’s Guide provided with the printer Ri 100.
You can shorten the processing time by putting a garment in the cassette while pre­heating the finisher.
2
Smoothing wrinkles/flattening fibers (Press )
Press the [Power] key to turn on the power.
Make sure the mode switching lever is set in the center.
Set the temperature of the heater. Set the temperature according to the fabric on which you are printing. The default setting is “High”.
When you move the mode switching lever to the left, processing starts. An alarm sounds after preheating is completed.
Confirm that the mode indicator light is off.
When the [Preheat] key is lit, press the [Preheat] key to start preheating. When the [Preheat] key is unlit, no operation is necessary because preheating is completed.
Press the [Stop/Unlock] key for 1 second or more to open the cover. When set to the profes­sional mode, it is not necessary to hold down the [Stop/Unlock] key.
Press the [Stop/Unlock] key for 1 second or more to open the cover. When set to the profes­sional mode, it is not necessary to hold down the [Stop/Unlock] key.
Page 3
3
Printing
For details, refer to User’s Guide provided with the printer Ri 100.
4
Fixing ink (Fix )
Make sure the mode switching lever is set in the center.
Set the temperature of the heater. Set the temperature according to the fabric on which you are printing. The default setting is “High”.
Set the amount of time that the heater is on. Set the time according to the fabric on which you are printing. The default setting is “Medium”.
When you move the mode switching lever to the right, processing starts. An alarm sounds after preheating is completed.
When the [Preheat] key is lit, press the [Preheat] key to start preheating. When the [Preheat] key is unlit, no operation is necessary because preheating is completed.
Press the [Stop/Unlock] key for 1 second or more to open the cover. When set to the profes­sional mode, it is not necessary to hold down the [Stop/Unlock] key.
Confirm that the mode indicator light is off.
Press the [Stop/Unlock] key for 1 second or more to open the cover. When set to the profes­sional mode, it is not necessary to hold down the [Stop/Unlock] key.
Page 4
Basic Usage of the Finisher
CAUTION:
If children use this machine, their parents must be with them and they should be very careful in using • this machine. Otherwise, injury or burns may result.
The finisher has “Standard mode” and “Professional mode”.
Standard mode
The factory-default setting is standard mode. The finisher has the following functions to prevent children from touching the inside of the finisher accidentally when it is very hot.
When the inside of the finisher exceeds 70 °C (158 °F), the front cover locks. To • open the front cover, press the [Stop/ Unlock] key for at least 1 second.
Professional mode
To use this mode, switch from standard mode. As this mode is for users who are accustomed to using the finisher, the front cover does not lock even when the temperature of the inside of the finisher exceeds 70 °C (158 °F). However, during press processing and fixing processing, the front cover locks regard­less of whatever mode is used to prevent erroneous operations.
How to Switch Between Stan- dard Mode and Professional Mode
Press the [Temperature] key and [Fix­ing Time] key simultaneously for at least 2 seconds.
DSB547
Unlock Cover
When set to standard mode, press the [Stop/ Unlock] key for at least 1 second.
When set to the professional mode, it is not necessary to hold down the [Stop/Unlock] key.
DSB548
© 2017 Ricoh Co., Ltd.
EN GB EN US EN AU J361-6607C
Loading...