R5433V Series
Li-ion/polymer 3/4/5Cell protector
The R5433V Series are high voltage CMOS-based protection ICs for over-charge/discharge of rechargeable 3/4/5cell Li-ion/Lithium polymer battery. Each of these ICs is composed of ten voltage detectors, reference units, a delay circuit, an oscillator, a counter, and logic circuits. Disconnection between the battery and the protection board can be detected.
SSOP-16 package is available.
FEATURES
• Supply Voltage (VDD)····································30V (Absolute Maximum Rating) |
• Over-discharge |
Detector Threshold Range ······· |
2.0 to 3.0V (0.005V Steps) |
||
• Operating Input Voltage Range (VDD)·············1.7V to |
25.0V |
(VDET2) |
Voltage Accuracy ···················· |
±2.5% |
|
• Supply Current (IDD) ·····································Typ.6.0μA |
|
Output Delay Time (tVDET2)······· |
Settable by Ext.capacitance1 |
||
• Over-charge |
Detector Threshold Range····· 3.6V to |
4.5V (0.005V Steps) |
• 0V-battery charge············································ |
Available |
|
(VDET1) |
Voltage Accuracy··············· ±25mV |
|
• Package ·························································· |
SSOP-16 |
Output Delay Time (tVDET1)···· 1.0s
BLOCK DIAGRAMS
R5433VxxxxA |
R5433VxxxxB |
VDD |
VDD |
VC1 |
VC1 |
VD1-1 |
|
|
VD1-1 |
VC2 |
|
VD2-1 |
|
Regulator |
VC2 |
VD2-1 |
Regulator |
|
|
|
VD1-2 |
|
Regulator |
|
VD1-2 |
Regulator |
|
|
|
|
|
|
|
|
||
|
|
|
Logic |
|
|
Logic |
|
|
|
0VDET2 |
|
Circuit |
|
0VDET2 |
Circuit |
|
|
|
|
|
Oscillator |
DS |
DS |
Oscillator |
DS |
DS |
|
|
|
Circuit |
|||||
VC3 |
|
VD2-2 |
|
|
VD2-2 |
Circuit |
||
|
|
|
VC3 |
|
|
|||
|
|
VD1-3 |
|
|
|
VD1-3 |
|
|
0VDET3 |
Counter |
0VDET3 |
Counter |
|
VC4 |
VD2-3 |
Logic |
VC4 |
VD2-3 |
Logic |
|
VD1-4 |
Circuit |
|
VD1-4 |
Circuit |
|
0VDET4 |
|
|
0VDET4 |
|
VC5 |
VD2-4 |
|
VC5 |
VD2-4 |
|
|
VD1-5 |
|
|
VD1-5 |
|
|
|
|
|
|
Regulator |
|
|
COUT |
|
|
COUT |
VSS |
VD2-5 |
|
|
VSS |
VD2-5 |
|
|
odd sw |
|
|
DOUT |
odd sw |
|
|
Regulator |
even sw |
|
|
even sw |
|
|
||
|
Logic |
tVDET2 |
|
Logic |
tVDET2 |
||
|
Circuit |
|
Circuit |
||||
|
|
|
DOUT |
||||
|
|
|
|
|
|
|
|
T Stop |
Logic |
|
|
T Stop |
Logic |
|
|
|
Circuit |
|
|
|
Circuit |
|
|
T Start |
|
|
|
T Start |
|
|
|
CTLT |
SEL1 |
SEL2 |
CT |
CTLT |
SEL1 |
SEL2 |
CT |
SELECTION GUIDE
Halogen Free |
Package |
Quantity per Reel |
Part No. |
||
|
SSOP-16 |
2,000pcs |
R5433V |
|
-E2-FE |
|
.xxx.$. |
||||
|
|
|
|
|
|
.xxx |
: Serial Number for the R5433V Series designing input two thresholds such as over-charge |
. |
: Select the output type from ( |
.A. |
) Nch. open drain or ( |
.B. |
) CMOS. |
|||
|
|
and over-discharge. |
|
|
|
|
|
|
||
|
.$. |
: Designation of Output delay option of Over-charge and Over-discharge. |
|
|
|
|
|
|
||
|
|
( |
.A. |
) tVDET1 : 1s, tVDET2 : 3.64 × C1(nF) |
|
|
|
|
|
|
PACKAGE
SSOP-16
16 15 14 13 12 11 10 9 |
|
1 |
DOUT |
|
9 |
NC |
|
||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
COUT |
|
|
|
10 |
NC |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
3 |
SEL2 |
|
|
|
11 |
VC5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4 |
SEL1 |
|
|
|
12 |
VC4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 |
DS |
|
|
|
13 |
VC3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
6 |
CT |
|
|
|
14 |
VC2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7 |
CTLT |
|
|
|
15 |
VC1 |
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
|
|
|
|
|
|
|
|
|
|||||||||
8 |
VSS |
16 |
VDD |
|
|||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
APPLICATIONS
•Li-ion/Li polymer protector of over-charge and over-discharge for battery pack
•Over-charge and discharge for notebook PCs, power tools, and any other gadgets using on board Li-ion/Li Polymer battery.
No. EK-266-111024 |
Li-ion / Li-polymer Multi-Cell protect IC |
1.The products and the product specifications described in this document are subject to change or discontinuation of production without notice for reasons such as improvement. Therefore, before deciding to use the products, please refer to Ricoh sales representatives for the latest information thereon.
2.The materials in this document may not be copied or otherwise reproduced in whole or in part without prior written consent of Ricoh.
3.Please be sure to take any necessary formalities under relevant laws or regulations before exporting or otherwise taking out of your country the products or the technical information described herein.
4.The technical information described in this document shows typical characteristics of and example application circuits for the products. The release of such information is not to be construed as a warranty of or a grant of license under Ricoh's or any third party's intellectual property rights or any other rights.
5.The products listed in this document are intended and designed for use as general electronic components in standard applications (o ce equipment, telecommunication equipment, measuring instruments, consumer electronic products, amusement equipment etc.). Those customers intending to use a product in an application requiring extreme quality and reliability, for example, in a highly specific application where the failure or misoperation of the product could result in human injury or death (aircraft, spacevehicle, nuclear reactor control system, tra c control system, automotive and transportation equipment, combustion equipment, safety devices, life support system etc.) should first contact us.
6.We are making our continuous e ort to improve the quality and reliability of our products, but semiconductor products are likely to fail with certain probability. In order to prevent any injury to persons or damages to property resulting from such failure, customers should be careful enough to incorporate safety measures in their design, such as redundancy feature, firecontainment feature and fail-safe feature. We do not assume any liability or responsibility for any loss or damage arising from misuse or inappropriate use of the products.
7.Anti-radiation design is not implemented in the products described in this document.
8.Please contact Ricoh sales representatives should you have any questions or comments concerning the products or the technical information.
RICOH COMPANY., LTD. Electronic Devices Company
■Ricoh presented with the Japan Management Quality Award for 1999.
Ricoh continually strives to promote customer satisfaction, and shares the achievements of its management quality improvement program with people and society.
http://www.ricoh.com/LSI/
RICOH COMPANY, LTD.
Electronic Devices Company
● Higashi-Shinagawa O ce (International Sales)
3-32-3, Higashi-Shinagawa, Shinagawa-ku, Tokyo 140-8655, Japan Phone: +81-3-5479-2857 Fax: +81-3-5479-0502
RICOH EUROPE (NETHERLANDS) B.V.
● Semiconductor Support Centre
Prof. W.H.Keesomlaan 1, 1183 DL Amstelveen, The Netherlands P.O.Box 114, 1180 AC Amstelveen
Phone: +31-20-5474-309 Fax: +31-20-5474-791
RICOH ELECTRONIC DEVICES KOREA Co., Ltd.
11 floor, Haesung 1 building, 942, Daechidong, Gangnamgu, Seoul, Korea Phone: +82-2-2135-5700 Fax: +82-2-2135-5705
RICOH ELECTRONIC DEVICES SHANGHAI Co., Ltd.
Room403, No.2 Building, 690#Bi Bo Road, Pu Dong New district, Shanghai 201203, People's Republic of China
Phone: +86-21-5027-3200 Fax: +86-21-5027-3299
■Ricoh awarded ISO 14001 certification.
The Ricoh Group was awarded ISO 14001 certification, which is an international standard for environmental management systems, at both its domestic and overseas production facilities. Our current aim is to obtain ISO 14001 certification for all of our business offices.
Ricoh completed the organization of the Lead-free production for all of our products. After Apr. 1, 2006, we will ship out the lead free products only. Thus, all products that will be shipped from now on comply with RoHS Directive.
RICOH COMPANY, LTD.
Electronic Devices Company
● Taipei o ce
Room109, 10F-1, No.51, Hengyang Rd., Taipei City, Taiwan (R.O.C.) Phone: +886-2-2313-1621/1622 Fax: +886-2-2313-1623