Page 1
Chapter
5
SETTINGS/MISCELLANEOUS
Changing Camera Settings................................. 120
Formatting a Card/Internal Memory ........................... 120
Keep Settings ............................................................ 121
Changing LCD Confirmation Time ............................. 122
Auto Power Off Setting ............................................... 123
Beep Sound Setting ................................................... 124
Power Save Mode Setting .......................................... 124
Changing the File Numbering System ....................... 125
Changing Video-Out Signal Method (NTSC/PAL)...... 126
Changing Display Language ...................................... 127
Initializing Settings ..................................................... 127
Using the Remote Control .................................. 129
Shooting ..................................................................... 129
Playing ....................................................................... 131
Erasing ....................................................................... 132
Page 2
Changing Camera Settings
This section explains how to format (initialize) a
SmartMedia memory card or the internal memory, and
how to change the various settings such as auto power
off, beep sound and keep settings.
Formatting a Card/Internal Memory
Note
• A SmartMedia memory card
with a write protect pad
attached to it cannot be
formatted. Remove the pad
to format the SmartMedia
memory card. See
“Protecting Against
Accidental Writing” (p. 26).
Follow the procedure below to format a SmartMedia
memory card or the internal memory.
Before using a new SmartMedia memory card or a
SmartMedia memory card that has been used on
another device (such as a PC), you need to format it
with the camera.
Important
Note
• Formatting a SmartMedia memory card or the internal memory will
erase all the files recorded on the card or in the memory (including
protected files). Copy any important files before formatting. See
“Copying Image Files” (p.103).
• SmartMedia memory cards formatted on another device may be
unusable.
1
Set the mode dial to [ ].
2
Press the or button to select
[FORMAT] and press the ENTER button.
120
SET 1/3
FORMAT
KEEP SETTINGS
LCD CONFIRMATION 1SEC.
AUTO POWER OFF 1MIN
BEEP SOUND ON
SELECT: CHANGE:
SEL.:ENTER
Page 3
3
Press the or button to select
SmartMedia memory card or internal
memory and press the ENTER button.
FORMAT
FORMAT MEMORY CARD
FORMAT INTERNAL MEMORY
BACK:CANCEL SEL.:ENTER
4
FORMAT
FORMAT
MEMORY CARD
START:RELEASE
CANCEL:CANCEL
The “FORMATTING” message will be displayed.
When formatting is completed, the display will
return to the SET menu.
Keep Settings
The keep settings mode is for saving settings after the
camera is turned off. The following settings can be
saved.
• Flash mode (p.60)
• Exposure compensation
(p.62)
• White balance (p.64)
• Date imprint (p.74)
• Language (p.127)
• Recording destination
(CARD/IN) (p.46)
• Focus mode (p.70)
• ISO sensitivity (p.73)
• Flash strength (p.61)
• Sharpness mode (p.79)
• Image with sound (p.58)
• Monochrome mode (p.80)
Non-Compressed mode (p.84)
•
• Exposure metering system
(Photometry) (p.86)
• S mode (p.87)
• Time Exposure mode (p.88)
• Negative mode(p.81)
• Red-Eye Reduction mode
(p.72)
5
Settings/Miscellaneous
121
Page 4
1
Set the mode dial to [ ].
2
Press the or button to select [KEEP
SETTINGS] and press the ENTER button.
SET 1/3
FORMAT
KEEP SETTINGS
LCD CONFIRMATION 1SEC.
AUTO POWER OFF 1MIN
BEEP SOUND ON
SELECT: CHANGE:
3
Press the or button to select the item
to be saved.
SEL.:ENTER
Note
• To cancel the setting, select
[OFF].
Note
• If you select 0 sec. for the
image confirmation time, the
shot image will not be
displayed on the LCD
monitor.
• The shot image will be
displayed until recording is
completed, regardless of the
preset image confirmation
time, when taking still picture/
text with sound, or when in
non-compressed (NC) mode.
4
Press the or button to select [ON].
KEEP SETTINGS
FLASH ON
+
/– OFF
WHITE BALANCE OFF
DATE IMPRINT OFF
LANGUAGE OFF
SELECT: CHANGE:
BACK:CANCEL SEL.:ENTER
Keep Setting will be activated. To set more items,
3
repeat steps
5
Press the ENTER button.
The display will return to the SET menu.
and 4.
1/4
Changing LCD Confirmation Time
When you press the shutter release button to take a
picture in
appears on the LCD monitor. You can select the time
for confirming the image after shooting to 0 sec., 1 sec.,
2 sec., 3 sec., 4 sec. and 5 sec.
1
Set the mode dial to [ ].
(Still Picture) mode, the shot image
122
Page 5
2
Press the or button to select [LCD
CONFIRMATION].
3
Press the or button to select the
image confirmation time (0 SEC., 1 SEC., 2
SEC., 3 SEC., 4 SEC., 5 SEC.) and press the
ENTER button.
SET 1/3
FORMAT
KEEP SETTINGS
LCD CONFIRMATION 1SEC.
AUTO POWER OFF 1MIN
BEEP SOUND ON
SELECT: CHANGE:
SEL.:ENTER
Auto Power Off Setting
The camera will turn off automatically (auto power off) in
recording and playback modes to conserve the battery if
it is left idle (no buttons operated) for the preset time.
You can select from 1 min., 3 min., 5 min., and OFF for
the time until the auto power off function is activated.
1
Set the mode dial to [ ].
2
Press the or button to select [AUTO
POWER OFF].
Note
• Turn the power on again to
reactivate the camera if it
shuts off in auto power off
mode.
• When using an AC adapter
(option), the auto power off
function is disabled even if
you have set a time (except
for interval shooting).
5
Settings/Miscellaneous
3
Press the or button to select the
preset time (1 MIN, 3 MIN, 5 MIN, OFF) and
press the ENTER button.
SET 1/3
FORMAT
KEEP SETTINGS
LCD CONFIRMATION 1SEC.
AUTO POWER OFF 1MIN
BEEP SOUND ON
SELECT: CHANGE:
If you select OFF, the auto power off function will
be disabled.
SEL.:ENTER
123
Page 6
Note
• An error beep is not
suppressed even when
[BEEP SOUND] is set to
[OFF].
Note
• This mode is used to save
10% power consumption
compared with the normal
mode.
Beep Sound Setting
The camera beeps to alert you when it records a
picture. You can enable or disable the beep by
changing the setting.
1
Set the mode dial to [ ].
2
Press the or button to select [BEEP
SOUND].
3
Press the or button to select [ON] or
[OFF] and press the ENTER button.
SET 1/3
FORMAT
KEEP SETTINGS
LCD CONFIRMATION 1SEC.
AUTO POWER OFF 1MIN
BEEP SOUND ON
SELECT: CHANGE:
If you select [OFF], the beep sound will be disabled.
SEL.:ENTER
Power Save Mode Setting
This mode is used to conserve power consumed by the
LCD monitor and extend the battery life.
1
Set the mode dial to [SET].
124
2
Press the and buttons to select
[POWER SAVE MODE].
3
Press the or button to select [ON] or
[OFF] and press the ENTER button.
SET 2/3
POWER SAVE MODE ON
SEQUENTIAL NO. OFF
DATE SETTING 2001/10/15
VIDEO OUT MODE NTSC
LANUAGE ENGLISH
SELECT: CHANGE:
SEL.:ENTER
Page 7
Changing the File Numbering System
By enabling or disabling sequential numbering, you can
determine the method for assigning consecutive
numbers to files. In both cases, there is never any
duplication of file names on the same memory card.
● When sequential numbering is ON
File names are assigned in sequence from R0010001 to
R9999999.
The camera always remembers the last number
assigned so that even when a new (blank) memory
card is inserted, the camera continues assigning
numbers in sequence from where it left off. In other
words, the numbers are not reset.
However if the new memory card contains a file number
higher than the last one remembered by the camera, file
naming will continue from after this higher number. For
example, if the highest number the camera remembers
is R0020500, and the new memory card contains a file
R0020600, file naming will resume from R0020601.
* To reset sequential numbering so that it will assign file
names from R0010001 again, initialize the settings (p. 127)
and insert a blank memory card.
● When sequential numbering is OFF
File names are assigned in sequence from RIMG0001
to RIMG9999, however anytime a new (blank) memory
card is inserted, the numbering resets back to
RIMG0001.
However if the new memory card already contains files,
file naming will begin from after the highest number on
the card. For example, if the new memory card contains
a file RIMG0800, file naming will begin from RIMG0801.
* When the file names reach RIMG9999, [FILE NUMBER
OVER] is displayed and no more images can be recorded.
See “Error Messages” (p.140).
Note
• Numbering starts from
RIMG0001 when the internal
memory is selected as the
recording destination.
• Using the consecutive
numbering system (when
[SEQUENTIAL NO.] is [ON])
is useful when submitting
images to digital printing
services or keeping files on a
PC as there is no risk of the
same number being assigned
twice.
5
Settings/Miscellaneous
1
Set the mode dial to [ ].
2
Press the or button to select
[SEQUENTIAL NO.].
125
Page 8
3
Press the or button to select [ON] or
[OFF] and press the ENTER button.
SET 2/3
POWER SAVE MODE OFF
SEQUENTIAL NO. OFF
DATE SETTING 2001/10/15
VIDEO OUT MODE NTSC
LANGUAGE ENGLISH
SELECT: CHANGE:
If you select [OFF], files will be assigned numbers
starting from RIMG0001.
SEL.:ENTER
Changing Video-Out Signal Method
(NTSC/PAL)
Switches the video system for connecting the camera to
a TV set to play record images on TV.
See
•“Connecting to a TV” (p.90) for instructions on how to connect the
camera to a TV.
•“Using Your Digital Camera in Other Countries” (p.144) for
information about the television systems.
126
1
Set the mode dial to [ ].
2
Press the or button to select [VIDEO
OUT MODE].
3
Press the or button to select [NTSC]
or [PAL] and press the ENTER button.
SET 2/3
POWER SAVE MODE OFF
SEQUENTIAL NO. OFF
DATE SETTING 2001/10/15
VIDEO OUT MODE NTSC
LANGUAGE ENGLISH
SELECT: CHANGE:
The video setting will be changed.
SEL.:ENTER
Page 9
Changing Display Language
The information on the LCD monitor can be displayed in
English, French, German and Japanese.
1
Set the mode dial to [ ].
2
Press the or button to select
[LANGUAGE].
3
Press the or button to select the
display language and press the ENTER
button.
SET 2/3
POWER SAVE MODE OFF
SEQUENTIAL NO. OFF
DATE SETTING 2001/10/15
VIDEO OUT MODE NTSC
LANGUAGE ENGLISH
SELECT: CHANGE:
The language setting will be changed.
SEL.:ENTER
Initializing Settings
You can reset all settings except the date.
1
Set the mode dial to [ ].
2
Press the or button to select
[INITIALIZE SETTING] and press the
ENTER button.
Note
• Enable the keep settings
mode to save the display
language setting. See "Keep
Settings" (p.121).
Important
Note
• Mode settings that have
been saved will also be
initialized.
5
Settings/Miscellaneous
SET 3/3
INITIALIZE SETTING
SELECT: CHANGE:
SEL.:ENTER
127
Page 10
Note
• Recorded files are preserved
intact even when the settings
are initialized.
3
Press the shutter release button.
INITIALIZE SETTING
INITIALIZE ALL SETTINGS?
START:RELEASE
CANCEL:CANCEL
The settings will be reset to their factory default
settings and the display will return to the SET
menu.
128
Page 11
Using the Remote Control
This section explains how to operate the camera using
the optional DR-3 remote control unit.
Shooting
The remote control unit can be used to operate the
camera. It is particularly convenient when the camera is
set up at a remote location or is in a fixed position.
1
Set the mode dial to shooting mode
( • • • • ) and press the
button to select the recording destination.
2
Decide the composition of the picture and
press the RELEASE button.
RELEASE
ERASE
FWD
PROGRAM
EV
MULTI
Use the zoom button to vary the size of the
subject. Press the
zoom button to magnify
the subject and press the
decrease the size of the subject.
● In
(Still Picture) mode
The self-timer LED will light and recording will
start about 2 seconds later.
(Text) mode
●
Recording starts as soon as the RELEASE
button is pressed.
● In
(Continuous Shooting) mode
Shots will be taken continuously while the
RELEASE button is pressed. Shooting will stop
when the RELEASE button is released and the
shots will be recorded.
ENTER
REV
zoom button to
Important
Note
• The remote control receiver
is located at the upper left of
the LCD monitor. Operate the
remote control unit by
pointing it at the LCD
monitor.
Note
• For instructions on replacing
the batteries and maintaining
the remote control unit, refer
to the accompanying manual.
5
Settings/Miscellaneous
129
Page 12
● In (Sound)/ (Motion Picture) mode
Recording of the sound and image will start
when the RELEASE button is pressed.
Recording will stop when the RELEASE button is
pressed again and the shots will be recorded.
■ Setting Exposure Compensation
1
Press the EV (+/–) button.
2
Set the exposure compensation level using
the FWD (왕) or REV (왓) button and press
the ENTER button.
Press the RELEASE button to take the picture.
■ Setting the Focus
Note
• When using MF (Manual)
mode, adjust the focus using
the FWD (왕) and REV (왓)
buttons, then press the
RELEASE button to take the
picture.
130
1
Press the PROGRAM button to select the
desired focus mode.
The focus setting changes in the following
sequence each time the button is pressed: AF
(Auto) → MF (Manual) → 2.5m →
Press the RELEASE button to take the picture.
● How to Cancel the Focus Mode Setting
Press the PROGRAM button and change the
focus mode.
∞ (Infinity).
Page 13
Playing
Use the remote control unit to play back recorded files.
1
Set the mode dial on the camera to [ ]
and press the button to select the
playback source.
The most recently recorded file will be played.
2
Press the FWD (왕) or REV (왓) button to
select a file.
RELEASE
ERASE
FWD
PROGRAM
EV
MULTI
The remote control unit buttons are operated in the
same way as the buttons on the camera.
ENTER
REV
■ Magnifying an Image (Zoom
Playback)
1
Press the PROGRAM button.
The image will be displayed in zoom playback.
5
Settings/Miscellaneous
131
Page 14
2
Press the or button and the FWD (왕)
or REV (왓) button to shift the playback
position.
Depending on the image size, you can change the
magnification by pressing the ENTER button. See
“Zoom Playback” (p.99).
● How to Cancel Zoom Playback Mode
Press the PROGRAM button.
■ Displaying Multiple Images (Multi
Image Playback)
1
Press the MULTI button.
The images will be displayed in Multi playback.
2
Press the or button and the FWD (왕)
or REV (왓) button to select a file to be
played back.
Important
Note
• Files cannot be restored
once they are erased. Before
starting to erase a file, make
sure that you want to erase it.
132
3
Press the ENTER button.
The selected image will be displayed in singleimage mode and multi-image playback mode will be
canceled.
Erasing
You can use the remote control unit to erase a recorded
file.
1
Set the mode dial on the camera to [ ]
and press the button to select the
erase source.
2
Press the ERASE button.
The erase menu will be displayed.
Page 15
3
Use the FWD (왕) or REV (왓) button to
select [ERASE SINGLE IMAGE] and press
the ENTER button.
ERASE
ERASE SINGLE IMAGE
ERASE ALL IMAGES
ERASE SELECTED IMAGES
SELECT:
BACK:CANCEL SEL.:ENTER
4
Use the FWD (왕) or REV (왓) button to
select the file to be erased and press the
RELEASE button.
RELEASE
ERASE
FWD
PROGRAM
EV
REV
MULTI
ENTER
Note
• To cancel operation, press
the CANCEL button on the
camera.
The selected file will be erased.
■ Erasing All Files
1
Select [ERASE ALL IMAGES] on the erase
mode screen (step 3 ).
2
Press the RELEASE button.
RELEASE
ERASE
FWD
PROGRAM
EV
MULTI
All the files will be erased.
ENTER
REV
5
Settings/Miscellaneous
Note
• To cancel operation, press
the CANCEL button on the
camera.
133
Page 16
Note
• To cancel selection, press
the ENTER button again.
Note
• To cancel operation, press
the CANCEL button on the
camera.
■ Erasing Selected Images
1
Select [ERASE SELECTED IMAGES] on the
erase mode screen (step 3 ).
2
Use the or button and the FWD (왕)
or REV (왓) button to select the file to be
erased and press the ENTER button.
Repeat step 2 to select more images.
3
Press the RELEASE button.
134
Loading...