Rank: A : Replace with new parts immediately.B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 11
T. Ito, Manager
Copier Technical Support
MODIFICATION BULLETIN NO. 4PAGE 2 OF 3
DETAILS OF MODIFICATION
2. TRANSPORT SECTION
Incorrect illustration
ISSUED ON: July 31, ’93
(Correct illustration)
Two pieces of the cushion shee t (#4 8 ) have be en stuck on the ent rance guide plate - lower (#17) an d two pieces of the cushion
(#49) have been stuck on the entrance guide plate - upper (#13).
These are to reduce noise whe n the junction pawls touch th e en trance guide plates. The shap e of the welded bracket for gu ide
rollers (#47) on both the upper and lower entrance guide plates have also been chan ge d as sho wn. This is to fix supp ort guid e
plates when installing this sorte r st apler on anoth er copier in the future. The part numbers have not been cha ng ed.
ModelSorter Stapler for A7 / N440 (Matt 20)Volt/Hz
Modified ArticleUpper and lower support guides
Reason for
To enable installing this sorter stapler on a new model, F400
Modification
Draw
No.
Old Parts
No.
New Parts
No.
A3742260Lower Support Guide0 → 1*507
A3742265Upper Support Guide0 → 1*517
04340060BPhilips Tapping Screw - M4x6n → n+41017
DescriptionRank
Q’ty Used
Old→New
Inter-
change-
ability
Date of
Modification
Parts needed for replacement by new part
Part No.DescriptionNo.Page
*: New index numbers
Serial
Number
Parts
Catalog
Rank: A : Replace with new parts immediately.B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 14
T. Ito, Manager
Copier Technical Support
MODIFICATION BULLETIN NO. 5PAGE 2 OF 3
17
DETAILS OF MODIFICATION
ISSUED ON: July 31, ’93
2. TRANSPORT SECTION
13
48
101
To enable installing this sorter stapler on a new model, F400,
Lower Support Guide (#50), Upper S uppo rt Gu ide (# 51), an d 4
pieces of Philips Tapping Screw - M4 x 6 have been enclo sed
in the machine box.
To enable the operation of the Matt 20 with a new model.
Modification
Inter-
Old P/NNew P/NDescriptionQ’ty Used
A3745100A3745105Main Control Board1 → 1X/O2011
change-
ability
Index No.Page
Date of
Modification
Parts Catalog
When the front door of the MATT20 or t he MA TT20 itself is opened or closed, a rush
current will run into the interface cable betwee n the main frame and the MATT20,
lowering voltage of the logic circuit.
When the MATT20 is installed on a new mod el, F400 , th is will make the MATT20
malfunction.
To prevent this problem with the F400 a rush current preven tio n circuit will be added in
the main control board.
The software will also be modif ied to operate the MATT20 wit h th e F400.
To prevent the bin lift wire from loosening on the pulley during transportation.
Modification
Inter-
Old P/NNew P/NDescriptionQ’ty Used
AA050076AA050084Bin Lift Wire2 → 2X/O 213
change-
ability
Index No.Page
Date of
Modification
Parts Catalog
Serial Number
The bin lift wire may loosen on the wire pu lley during machine transportat ion and the
wire may be wound up wrongly as shown in the figure 1. This will change the bin stop
positions, resulting in pa per ja ms.
To prevent this proble m, th e bin lift wire (#2) has been length en ed as shown in the
figure 2 to wind a half tu rn more on th e pu lley.
Refer to RTB No A7-017 and N44 0-008 for the new wire installation procedure.
As per Infotec’s request, the color of the exte rior cove rs h as been change d.
1 → 1
X/X3011
Page 21
MODIFICATION BULLETIN NO. 8 PAGE 2 OF 2
ISSUED ON: January 31, ’94
MODEL NAME
Savin Sorter Stapler 3115/60USA, CanadaA374-15
Ricoh ST24
NRG SR3227
Infotec SS203220, 240/50EuropeA374-26 3D30730001
V/HzDESTINATIONCODESERIAL NUMBER
115/60
220, 240/50
115/60
220, 240/50
Whole WorldA374-17
Whole WorldA374-25
Page 22
MODIFICATION BULLETIN NO. 9 PAGE 1 OF 2
ISSUED ON: February 15, ’94
ModelSorter Stapler for A7/N440/F400Volt/Hz
Modified ArticleS/S Mounting Frame
Reason for
As per field request
Modification
As per field request, the S/S mou nt ing frame has been registered as a service part.
P/NDescriptionQ’ty Used
Index No.Page
A3741151S/S Mounting Frame1* 527
* New Index No.
Parts Catalog
Date of
Modification
Serial Number
*52
S. Hamano, Assistant General Manager
Technical Support Department
Page 23
MODIFICATION BULLETIN NO. 9 PAGE 2 OF 2
ISSUED ON: February 15, ’94
MODEL NAME
Savin Sorter Stapler 3115/60USA, CanadaA374-15
Ricoh ST24
NRG SR3227
Infotec SS203220, 240/50EuropeA374-26
V/HzDESTINATIONCODESERIAL NUMBER
115/60
220, 240/50
115/60
220, 240/50
Whole WorldA374-17
Whole WorldA374-25
Page 24
MODIFICATION BULLETIN NO. 10 PAGE 1 OF 3
ISSUED ON: July 31, ’94
ModelSorter Stapler for A7 / N440 / F400Volt/Hz
Modified ArticleCushion - Jogger Holder
Reason for
To reduce noise
Modification
Draw
No.
Old Parts
No.
New Parts
No.
A3744182Cushion - Jogger Holder
DescriptionRank
Q’ty Used
Old→→New
0 → 1
Inter-
change-
ability
Date of
Modification
Parts needed for replacement by new part
Part No.DescriptionNo.Page
* New Index
Serial
Number
Parts
Catalog
* 3913
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 25
MODIFICATION BULLETIN NO. 10 PAGE 2 OF 3
[A]
[B]
ISSUED ON: July 31, ’94
DETAILS OF MODIFICATION
To reduce noise, the Jogger Holder Cushion [A] has been added to the Jogge r Lowe r Ho lde r (A37 44 181) [B].
S. Hamano, Assistant General Manager
Technical Support Department
To minimize paper jams at the entrance of the sorter stapler
Modification
Draw
No.
Old Parts
No.
A3742265A3742264Upper Support Guide
New Parts
No.
A3742266Junction Pawl Guide Mylar
DescriptionRank
Q’ty Used
Old→→New
1 → 1
0 → 1
Date of
Modification
Inter-
change-
ability
X/O517
Parts needed for replacement by new part
Part No.DescriptionNo.Page
* New Index
Serial
Number
Parts
Catalog
* 537
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 28
MODIFICATION BULLETIN NO. 11 PAGE 2 OF 3
ISSUED ON: July 31, ’94
DETAILS OF MODIFICATION
It was reported that in th e combination of the F400 and Matt20, paper jam occurs at the exit of the copier main body
if the paper is face curled.
To counter this, the Junction Pawl Gu ide Myla r [A] has been added to the Upp er Su pport Guide [B].
A3742264
A3742265 [B]
A3742266 [A]
S. Hamano, Assistant General Manager
Technical Support Department
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 31
MODIFICATION BULLETIN NO. 12 PAGE 2 OF 3
ISSUED ON: July 31, ’94
DETAILS OF MODIFICATION
It was reported that whe n face curled thick paper is used in the proof tray mode, the paper le ad ing edg e hit s the
exit roller guide [A] and a paper jam occurs.
To counter this, a hexagonal nut [B] has been insert ed between the plate spring [C] and the exit roller guide, so
that the angle [θ] between the guid e an d th e pa pe r has be en redu ced. Due to this modificatio n, the le ngth of the
screw [D] holding the plate spring has been change d.
The exit roller guide [A] is not listed in the parts catalog, but this part was used from the 1st mass-p rod uction.
[A]
[D]
θ
[B]
1
θ
[D]
[A]
[C]
S. Hamano, Assistant General Manager
Technical Support Department
ModelSorter Stapler for A7 / N440 / F400 / SP40Volt/Hz
Modified ArticleMain Control Board
Reason for
To increase the torque margin of the main motor
Modification
Draw
No.
Old Parts
No.
A3745105A3745115Main Control Board
A3745108A3745113IC - AM27C256 - 205DC
AA043202Timing Belt - 145 x L
AB030386Pulley - 40Z
New Parts
No.
AA043450Timing Belt - 100 x L
AB030497Pulley - 16Z
DescriptionRank
Q’ty Used
Old→New
1 → 1
1 → 1
1 → 0
0 → 1
1 → 0
0 → 1
Date of
Modification
Inter-
change-
ability
X/O2011
X/O2111
X/911
/X911
X/ X/O as a set711
/X711
Parts needed for replacement by new part
Part No.DescriptionNo.Page
Serial
Number
Parts
Catalog
A3742216A5542216Encoder
AB030387Pulley - 34Z
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
AB030498Timing Pulley - 27Z
1 → 1
0 → 1
1 → 0
X/X811
X/107
/X107
Page 34
MODIFICATION BULLETIN NO. 13 PAGE 2 OF 4
R103
Reissued on: December 15, ’94
ISSUED ON: November 15, ’94
DETAILS OF MODIFICATION
To increase the torqu e marg in of the main mot o r, the RO M (soft ware) and the two resistors on the main contro l boa rd
have been changed.
1. ROM (Software)
The paper transportation speed at the sort er en tra nce has been reduced to lessen th e mechanical load applied to
the main drive motor.
2. Main motor’s torque up (810 gf cm → 940 gf cm)
The resistors have been change d to increase the motor drive curren t from 1.2A to 1.5A as follows.
Note : When modify the old main cont rol board, R104 (R102), R105 (R103) and ROM sh ould be chan ged to geth er.
A3745105
R104
R105
R110
R102
R109
A3745100
Page 35
MODIFICATION BULLETIN NO. 13 PAGE 3 OF 4
Reissued on: December 15, ’94
ISSUED ON: November 15, ’94
8
P/N A3742216
P/N A5542216
9
P/N AA04 3202
P/N AA04 3450
DETAILS OF MODIFICATION
3. Main drive pulleys and timing belt.
Additionally, to redu ce th e mechanical load on the main drive motor, the tooth shape of th e following parts have
been changed from S2M to S3M.
Page 8
Page 12
10
P/N AB030387
P/N AB030498
7
P/N AB03 03 86 → AB030497
S. Hamano, Assistant General Manager
Technical Support Department
To reduce the mechanical load applied to the main drive motor
Exit Roller
2 → 2
Volt/Hz
Inter-
change-
ability
X/O287
Parts Catalog
Index No.Page
Date of
Modification
To reduce the mechanical load applied to the main drive moto r, the exit roller has been changed to a new t ype one
which has two bushings containing lubricant.
Exit Roller
Serial Number
Old
New
S. Hamano, Assistant General Manager
Technical Support Department
S. Hamano, Assistant General Manager
Technical Support Department
Page 40
MODIFICATION BULLETIN NO. 15 PAGE 2 OF 2
ISSUED ON: November 15, ’94
V/HzDESTINATIONCODESERIAL NUMBER
MODEL NAME
Savin Sorter Stapler 3115/60USA, CanadaA374-15
4063110001
Ricoh ST24
115/60
220, 240/50
Whole WorldA374-17
A3203110063
NRG SR3227
115/60
220, 240/50
Whole WorldA374-25
4863110001
Infotec SS203220, 240/50EuropeA374-26
3D31130001
Page 41
MODIFICATION BULLETIN NO. 16 PAGE 1 OF 3
ISSUED ON: November 15, ’94
Model
Modified Article
Reason for
Modification
Draw
No.
Old Parts
A3743505A3743505
A3743506A3743506
A3744561A3744562
A3743519A3743520
No.
Sorter Stapler for A7 / N440 / F400 / SP40
Parts Catalog
Parts catalog correction
New Parts
No.
A3743507
A3743508
DescriptionRank
Bin Ass’y
Lower Bin Ass’y
Bin Ass’y
Lower Bin Ass’y
Stapler Guide
Pressure Guide Mylar
Volt/Hz
Q’ty Used
Old→New
20 → 19
0 → 1
20 → 19 SAVIN
0 → 1
1 → 1
20 → 19
Inter-
change-
ability
X/O* 2315
X/O* 2315
X/O1515
X/O1615
Parts needed for replacement by new part
Part No.DescriptionNo.Page
RICOH
NRG
INFOTEC
Date of
Modification
Serial
Number
Parts
Catalog
1815
1815
A3743522
A3743514
A3743526
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Bin Support Film
Paper Support Film
Bin Spacer
1 → 1
0 → 19
0 → 2
* New Index
* 2415
* 2515
* 2615
Page 42
MODIFICATION BULLETIN NO. 16 PAGE 2 OF 3
15
A3744561 → A3744562
DETAILS OF MODIFICATION
Please correct your parts catalo g as sho wn.
ISSUED ON: November 15, ’94
* 25
A3743514
18
A3743505
16
A3743519 → A3743520
18 → * 23
A3743505 → A3743507
A3743506 → A3743508
* 24
A3743522
* 26
A3743526
S. Hamano, Assistant General Manager
Technical Support Department
Page 43
MODIFICATION BULLETIN NO. 16 PAGE 3 OF 3
ISSUED ON: November 15, ’94
MODEL NAME
Savin Sorter Stapler 3115/60USA, CanadaA374-15
Ricoh ST24
NRG SR3227
Infotec SS203220, 240/50EuropeA374-26
V/HzDESTINATIONCODESERIAL NUMBER
115/60
220, 240/50
115/60
220, 240/50
Whole WorldA374-17
Whole WorldA374-25
Page 44
M. Iwasa, Manager
Technical Support Department
MODIFICATION BULLETIN NO. 17 PAGE 1 OF 2
ISSUED ON: April 30, ’95
ModelSorter Stapler for A7 / N440 / F400 / SP40Volt/Hz
Modified ArticleUpper Gripper Arm / Drive Cam
Reason for
To ensure the function of the gripper.
Modification
Date of
Modification
To ensure the function of the gripper, the shape of the following parts has been changed.
NOTE: When replacing one of th ese parts, please replace the other part at the same time. The old pa rts are
no longer available.
Old P/NNew P/NDescriptionQ’ty Used
A3744651A3744658Upper Gripper Arm
A3744666A3744667Drive Cam