According to this correction, the schematic of the main board has be en chan ged
as follows.
These two zener diodes have been added.
Date of
Modification
Serial Number
Zener Diodes
T. Ito, Manager
Copier Technical Support
MODIFICATION BULLETIN NO. 2 Page 2 of 2ISSUED ON: August 31, ’92
MODEL NAME
SAVIN ADF for 9130115/60USA, CanadaA365-15
NRG F321115/60S. AmericaA365-16
RICOH DF40115/60USA, CanadaA365-17
NRG F321220, 240/50Europe etc.A365-25
INFOTEC ADF-1220, 240/50EuropeA365-26
RICOH DF40220, 240/50Europe etc.A365-27
V/HzDESTINATIONCODESERIAL NUMBER
Reissued on: September 30, ’92
MODIFICATION BULLETIN NO. 3 Page 1 of 3ISSUED ON: August 31, ’92
ModelADF for E7Volt/Hz
Modified ArticleUpper Unit Stand etc.
Reason for
To hold the upper unit and ADF at a proper position
Modification
To hold the upper unit and ADF at a proper po sitio n, the follo wing
parts have been packed as an acce ssory to the ADF.
P/NDescriptionQ’tyPageIndex
P/N A3651486
(Index No. 23)
P/N AA143183
(Index No. 22)
P/N 5446 5832
(Index No. 26)
A3651485Upper Unit Stand15*21
AA143183Stepped Screw15*22
A3651486Magnet15*23
A3652080Instruction Decal15*24
A3656001Screw Driver15*25
P/N A365 2080
(Index No. 24)
54465832Connector Guide Pin15*26
Date of
Modification
Serial Number
P/N A365 1485
(Index No. 21)
P/N A3656001
(Index No. 25)
* New Index
Please refer to the E7 RTB No. 3 for details.
Reissued on: September 30, ’92
T. Ito, Manager
Copier Technical Support
MODIFICATION BULLETIN NO. 3 Page 2 of 3ISSUED ON: August 31, ’92
Regarding the cut-in serial number in the production line, plea se ref er to the next page. These pa rts have also
been added before shipme nt to th e do cument feeders which have th e fo llowing serial numbers.
Rank: A : Replace with new parts immediately.B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
To facilitate manufacturing, the feed-out mylar has been changed.
Inter-
Old P/NNew P/NDescriptionQ’ty Used
H5201450A3951450Mylar - Feed Out
1 → 1
change-
ability
X/O2511
Date of
Modification
Parts Catalog
Index No.Page
Serial Number
Mylar - Feed Out
MODIFICATION BULLETIN NO. 10 PAGE 2 OF 3
ISSUED ON: July 31, ’95
DETAILS OF MODIFICATION
With the old mylar, the end of the mylar was inse rted into the gap between the cover an d the
antistatic brush. With the ne w mylar, the edge is free and a thicker material is used.
Antistatic Brush
Mylar - Feed Out
Exit Roller
Old
Antistatic Brush
Mylar - Feed Out
Exit Roller
New
M. Iwasa, Manager
Technical Support Departme nt
MODIFICATION BULLETIN NO. 10 PAGE 3 OF 3
ISSUED ON: July 31, ’95
MODEL NAME
SAVIN ADF for 9130115/60USA, CanadaA365-153915040001
To prevent interference with the exit roller drive belt.
New Parts
No.
DescriptionRank
Grip Cover
Q’ty Used
Old→New
1 → 1
1 → 1
1 → 1
1 → 1
Date of
Modification
Inter-
change-
ability
X/O-17, -2717
X/O-1517
X/O
X/O-16, -2517
-26
Destination
Serial
Number
Parts
Catalog
No.Page
17
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
MODIFICATION BULLETIN NO. 12 PAGE 2 OF 3
ISSUED ON: May 15, ’96
T. Inoue, General Manager
1st Field Information Dept. QAC
DETAILS OF MODIFICATION
To prevent interfere nce with the exit roller drive belt , a pa rt of the grip cove r h as been re move d.
Grip Cover
This part has
been removed.
MODIFICATION BULLETIN NO. 12 PAGE 3 OF 3
ISSUED ON: May 15, ’96
MODEL NAME
SAVIN ADF for 9130115/60USA, CanadaA365-153916010001