MODIFICATION BULLETIN NO. 2 Page 1 of 2ISSUED ON: October 15, ’91
ModelN210Volt/Hz
Modified ArticleRubber Cushion
Reason for
To prevent the interface board connector from coming out
Modification
Date of
Modification
A rubber cushion has been added to the main board to prevent the interface board connector from coming out from the main
board connector due to wrong DF harness wiring. If a poor connection between the interface board and main board occurs,
RAM data is cleared.
The procedure of wiring the DF harness has been changed. (Refer to RTB No. 2.)
New P/NDescription
54461098Rubber Cushion0 - 1#1643
Q’ty Used
Old New
Index No.Page No.
# : New Index No.
Serial Number
#16
T.Ito, Manager
Copier Technical Support
Page 10
MODIFICATION BULLETIN NO. 2 Page 2 of 2ISSUED ON: October 15, ’91
JAPAN PRODUCTIONRIF PRODUCTION
MODEL NAMEV/HzDESTINATION
CODESERIAL NUMBERCODESERIAL NUMBER
Savin 9150115/60USA, CanadaA075-15From First Production
Nashua 3115115/60Canada, L.AmericaA075-16From First Production
Ricoh FT4415115/60USA, CanadaA075-172921070171
Ricoh FT4415110/60TaiwanA075-19From First Production
Reissued on : November 15, ’91
Nashua 3115
infotec 9215
Ricoh FT4415
Ricoh FT4415
Ricoh FT4415
220,230-240/50
220,230-240/50
220,230-240/50
220,230-240/60
220,230-240/50
Europe. etc.A075-25From First ProductionA075-45
EuropeA075-263B50710033A075-46
Europe, etc.A075-272921070758A075-47
Phillipin, etc.A075-28From First Production
AsiaA075-292921072048
Page 11
MODIFICATION BULLETIN NO. 3 Page 1 of 2ISSUED ON: October 15, ’91
ModelN210Volt/Hz
Modified ArticleRear Heater Holder
Reason for
To prevent the fusing drive gear from heat damage
Modification
To prevent the fusing drive gear [A] from heat damage, the shape of the rear heater holder has been changed as
shown.
Old P/NNew P/NDescription
A0484101A0484105Rear Heater Holder1 - 1X/O531
Q’ty Used
Old New
Interchangeability Index No. Page No.
[A]
Date of
Modification
Serial Number
5
T .Ito, Manager
Copier Technical Support
Page 12
MODIFICATION BULLETIN NO. 3 Page 2 of 2ISSUED ON: October 15, ’91
JAPAN PRODUCTIONRIF PRODUCTION
MODEL NAMEV/HzDESTINATION
CODESERIAL NUMBERCODESERIAL NUMBER
Savin 9150115/60USA, CanadaA075-15721090001
Nashua 3115115/60Canada, L.AmericaA075-16From First Production
MODIFICATION BULLETIN NO. 7 Page 1 of 2ISSUED ON: April 15, ’92
ModelN210Volt/Hz
Modified ArticleMylar Seal 19 x 45
Reason for
To prevent the upper cover from being scratched
Modification
Modification
By opening /closing the platen cover, part A of the upper cover may be scratched by the edge of t he platen cover. To
prevent this, a mylar seal has been added on part A of the upper cover.
Old P/NNew P/NDescriptionQ’tyInterchangeabilityIndex No.Page
----A0541255Mylar Seal 19 x 45
0 → 1
----383
38
A
Date of
Serial Number
T. Ito, Manager
Copier Technical Support
Page 20
MODIFICATION BULLETIN NO. 7 Page 2 of 2ISSUED ON: April 15, ’92
MODIFICATION BULLETIN NO. 9 Page 1 of 2ISSUED ON: June 15, ’92
ModelN210Volt/Hz
Modified ArticleSeparation Torque Limiter
Reason for
To improve the vertical magnification
Modification
With the old part, the image is slightly prolonged in vertical direction, after the paper is free fr om the reverse roller.
This is because the paper separation force of the reverse roller interferes with smooth paper transp ortation. The torque limiter
of the reverse roller has been modified.
MODIFICATION BULLETIN NO. 11 Page 1 of 2ISSUED ON: July 15, ’92
ModelN210Volt/Hz
Modified ArticleLower Registration Roller
Reason for
To improve the vertical magnification
Modification
With the old part, the image is slightly prolonged in the vertical direction due to paper slipping a t the registration rollers.
( * While the paper is caught by the reverse roller, the paper slips slightly at the registration ro ller. Then, after the paper is
free from the reverse roller , the paper speed returns to normal. )
To minimize paper slipping , a new lower registration roller, with the surface of the increased fric tion, has been produced.
MODIFICATION BULLETIN NO. 12 Page 1 of 2ISSUED ON: August 31, ’92
ModelN210Volt/Hz
Modified ArticlePaper Lift Clutch Support Bracket
Reason for
To ensure gear engagement
Modification
To ensure the gears engage, the shape of the paper lift clu tch supp ort bracke t ha s been mod ified to strengthen it.
Old P/NNew P/NDescriptionQ’tyInterchangeabilityIndex No.Page
A0482714A0482728Paper Lift Clutch Support Bracket
-------52031190Bushing 8 x 10 x 4mm
1 → 1
0 → 1
X/X1141
------2341
NOTE : For this new support bracke t, the shaft A welded to the rear frame has been le ngthened.
The lift arm shaft (AA14 02 88) h as also bee n len gt he ne d. Its interchangeabilit y is X/O. (The part number has not
been changed. The old part is no long er supplied. )
A
Date of
Modification
Serial Number
11
103
AA140288
23
11
103
T. Ito, Manager
< New >< Old >
Copier Technical Support
Page 28
Reissued on: September 30, ’92
MODIFICATION BULLETIN NO. 12 Page 2 of 2ISSUED ON: August 31, ’92
MODIFICA TION BULLETIN NO. 14 Page 1 of 4ISSUED ON: October 31, ’92
ModelN210Volt/Hz
Mod i fied ArticleExteriors and Operating Instructions
Reason for
At Gest etn er gr oup request
Modification
Date of
Modification
At Gestetner group requ est, the Nashua brand models (A075-16, 25) have been modified for sale und er all their brands.
The machine codes have been standardized (A075-16 → A075-10, A075-25 → A075-22).
MODIFICA TION BULLETIN NO. 14 Page 2 of 4ISSUED ON: October 31, ’92
DETAILS OF MODIFICATION
< A075-10 Only>
Old P/NNew P/NDescriptionQ’ty UsedInterchangeabilityPageIndex No.
A0758677-----Operating Instructions - English (NSA)1 → 0X/ 69 26
-----A0758697Operating Instructions - English (NRG)0 → 1/O 69 26
A0758678-----Operating Instructions - French (NSA)1 → 0X/ 69 26
-----A0758698Operating Instructions - French (NRG)0 → 1/O 69 26
< A075-22 Only>
Old P/N New P/NDescriptionQ’ty UsedInterchangeabilityPageIndex No.
A0758670-----Operating Instructions - English (NSA)1 → 06926
A0758671-----
A0758672-----Operating Instructions - French (NSA)1 → 06926
A0758673-----Operating Instructions - Italian (NSA)1 → 06926
A0758674-----
Operating Instructions - German
(NSA)
Operating Instructions - Spanish
(NSA)
1 → 06926
1 → 06926
* 2
NOTE: *1 : Even though the model name is missing from the new front cover, it can be placed by sticking one of the new name plate.
The old front cover is no longer supplied.
*2 : The operating instructions for the European market have been eliminated from the machine box. They are supplied as
the merchandise, through the sales section.
Page 33
T. Ito, Manager
Copier Technical Support
DETAILS OF MODIFICATION
MODIFICA TION BULLETIN NO. 14 Page 3 of 4ISSUED ON: October 31, ’92
P/N A0756448
P/N A0756447
Decal - Key Top Cover
Front Cover
Name Plate
P/N A0546335
P/N A0546330
Operation Panel
Page 34
MODIFICA TION BULLETIN NO. 14 Page 4 of 4ISSUED ON: October 31, ’92
MODEL NAMEV /HzDESTINATION
CODESERIAL NUMBERCODESERIAL NUMBER
Gestetner 2515Z
Nashuatec 3115
Savin 9150115/60USA, CanadaA075-15
Nashua 3115115/60Canada, L.AmericaA075-16Se rvice Parts Only
Ricoh FT4415115/60USA, CanadaA075-17
Ricoh FT4415110/60TaiwanA075-19
Gestetner 2515Z
Nashuatec 3115
Nashua 3115220, 230-240/50Europe. etc.A075-25Service Parts OnlyA 075-45Service Parts Only
115/60Canada, L. AmericaA075-10From 1st Production
220, 230-240/50Europe etc.A075-22From 1st ProductionA075-42From 1st Production
JAPAN PR ODUCTIONRIF PR ODUCTION
Page 35
ISSUED ON: February 15, ’93
T. Ito, Manager
Copier Technical Support
MODIFICATION BULLETIN NO. 15 PAGE 1 OF 2
ModelN210Volt/Hz
Modified ArticleGear - 35Z
Reason for
To increase durability
Modification
Date of
Modification
Serial Number
To increase durability, the gear has bee n mod ifie d to one with ball-bearings inside, instead of dry bearin gs.
When the new gear is installed, the follo wing two wash ers (P/N 52031870 and 08075074) should be in stalled together
as shown in the illustration.
Old P/NNew P/NDescriptionQ’ty UsedInterchangeability
AB013434AB013841Gear 35Z1 → 1X/X5116
AA132025Seal 1 x 8 x 121 → 05129
52031870Thrust Washer - 8 x 14 x 1.50 → 1 X/O as a set51# 24
08075074Washer - 8 x 15.8 x 0.50 → 151# 110
<DRIVE SECTION II>
Parts catalog
PageIndex No.
# New Index
108
29
16
108
16
# 110
# 24
Gear 35Z
OldNew
Dry Bearing
Ball Bearing
Page 36
MODIFICATION BULLETIN NO. 15 PAGE 2 OF 2
ISSUED ON: February 15, ’93
MODEL NAMEV/HzDESTINATION
CODESERIAL NUMBERCODESERIAL NUMBER
Gestetner 2515Z
Nashuatec 3115
Savin 9150115/60USA, CanadaA075-157230100001
Nashua 3115115/60Canada, L.AmericaA075-16Service Parts Only
Ricoh FT4415115/60USA, CanadaA075-17A2922120153
Ricoh FT4415110/60TaiwanA075-19A292302XXXX
Gestetner 2515Z
Nashuatec 3115
Nashua 3115220, 230-240/50Europe. etc.A075-25Service Parts OnlyA075-45
To standardize the parts with Pigeon, the following parts have been changed.
A0069003A0699001Cleaning Entrance Seal
----AA150102Seal - 0.05 x 12 x 25
A0063660A0693580Toner Collection Shaft
A0483581A1103580Upper Cleaning Casing
A0483588A1103585Lower Cleaning Casing
New Parts
No.
DescriptionRank
Q’ty Used
Old → New
1 → 1
0 → 2
1 → 1
1 → 1
1 → 1
Date of
Modification
Inter-
change-
ability
O/O1027
* 13627
O/O2727
O/O127
O/O827
Part needed for replacement by new
part
Part No.Description No. Page
Serial
Number
Parts
Catalog
A0484071A1104071Front Side Plate
A0485853A1105853Left AC Drive Board Bracket
A0487601A1103310Case - Lower - Development
AD038023AD038054Roller - Agitate Mix
Rank: A : Replace with new parts immediately.B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
I Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
A0483921A1103921T/S Corona Unit - EU
AD023058AD023082T/S Corona Guide Plate
AA010015AA010072Ozone Filter
A0061724A1101724Rear Spring Plate
New Parts
No.
DescriptionRank
T/S Corona Unit Casing NA, AA, ME
T/S Corona Unit Casing NA, AA, ME
Q’ty Used
Old → New
1 → 1
1 → 1
1 → 1
1 → 1
1 → 1
1 → 1
1 → 1
1 → 1
1 → 1
Inter-
change-
ability
O/O4225
O/O75
O/O1229
O/O1229
O/O129
O/O129
O/O829
O/O137
O/O
Part needed for replacement by new part
Part No.DescriptionNo. Page
Parts
Catalog
101811
13
Page 45
MODIFICATION BULLETIN NO. 19 PAGE 3 OF 4
DETAILS OF MODIFICATION
NOTE: * 1. Cleaning Entrance Seal
The cleaning entrance seal has been changed to that of A7 and Pigeon. When replacing this
seal with new type, the seals (P/N AA150102: seal - 0.05 x 12 x 25) should be stuck at both
ends as shown below.
ISSUED ON: August 31, ’93
36
36
10
T. Ito, Manager
Copier Technical Support
Page 46
MODIFICATION BULLETIN NO. 19 PAGE 4 OF 4
ISSUED ON: August 31, ’93
MODEL NAMEV/HzDESTINATION
Gestetner 2515Z
Nashuatec 3115
Savin 9150115/60USA, CanadaA075-15
Nashua 3115115/60Canada, L.AmericaA075-16Service Parts Only
Ricoh FT4415115/60USA, CanadaA075-17
Ricoh FT4415110/60TaiwanA075-19
Gestetner 2515Z
Nashuatec 3115
Nashua 3115220, 230-240/50Europe. etc.A075-25Service Parts OnlyA075-45Service Parts Only
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 62
MODIFICATION BULLETIN NO. 27 PAGE 2 OF 3
ISSUED ON: December 31, ’93
[A]
DETAILS OF MODIFICATION
To prevent the AC harness from being damaged by the edge of the front side plate, a seal (AA150364) [A] has
been added to cover th e ed ge.
S. Hamano, Assistant General Manager
Technical Support Department
Page 63
MODIFICATION BULLETIN NO. 27 PAGE 3 OF 3
ISSUED ON: December 31, ’93
MODEL NAMEV/HzDESTINATION
Gestetner 2515Z
Nashuatec 3115
Savin 9150115/60USA, CanadaA075-157231100001
Nashua 3115115/60Canada, L.AmericaA075-16Service Parts Only
Ricoh FT4415115/60USA, CanadaA075-17A2923110001
Ricoh FT4415110/60TaiwanA075-19A292312XXXX
Gestetner 2515Z
Nashuatec 3115
Nashua 3115220, 230-240/50Europe. etc.A075-25Service Parts OnlyA075-45Service Parts Only
To facilitate manufacturing, the fan motor bracket (P/N A04 8109 2) an d the sup po rt sprin g pla te (P/N A0 4810 95 ) has
become one unit (P/N A1101090).
Incorrect P/NCorrect P/NDescriptionQ’ty Used
A0481092Fan Motor Bracket
A0481095Support Spring Plate
04430060W
A1101090Exhaust Fan Stay
Hexagon Head Tapping Screw M3 x 6
1 → 0
1 → 0
n → n-1
0 → 1
Inter-
change-
ability
X/O1037
Index No.Page
Parts Catalog
1037
1137
10137
Serial Number
S. Hamano, Assistant General Manager
Technical Support Department
To facilitate manufact uring, the screw which is fixed on the rear side of the lower registration guide (P/N A0 75 2571 ) has
been changed from pan head screw to knob screw.
Old P/NNew P/NDescriptionQ’ty Used
03130040WPhilips Pan Head Screw - M3 x 4
A0752573Knob Screw
n → n-1
0 → 1
Inter-
change-
ability
O/O* 3917
Parts Catalog
Index No.Page
10217
Serial Number
Lower registration guide
* 39
S. Hamano, Assistant General Manager
Technical Support Department
Page 76
MODIFICATION BULLETIN NO. 33 PAGE 2 OF 2
ISSUED ON: April 30, ’94
MODEL NAMEV/HzDESTINATION
Gestetner 2515Z
Nashuatec 3115
Savin 9150115/60USA, CanadaA075-15
Nashua 3115115/60Canada, L.AmericaA075-16Service Parts Only
Ricoh FT4415115/60USA, CanadaA075-17
Ricoh FT4415110/60TaiwanA075-19
Gestetner 2515Z
Nashuatec 3115
Nashua 3115220, 230-240/50Europe. etc.A075-25Service Parts OnlyA075-45Service Parts Only
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
n → n-1
0 → 1
X/X*11239
* New Index
10439
Page 80
MODIFICATION BULLETIN NO. 35 PAGE 2 OF 3
New
* New Index
ISSUED ON: August 31, ’94
Due to vendor chang e, the shape of the ton er supply clutch has been chang ed . Because of this change, the shape of some
other parts have also been changed. The interchangeability of the toner sup ply clutch assembly is O/O. However, the old
parts and new parts are not intercha ng ea ble individually. They are interchangeable as a set.
Page 38
21
(P/N AA080039)
115
(P/N 07200030E)
Old
78.5mm
Old
1 (P/N A0541135)
36mm
(P/N AX210024)
3
(P/N AX210024)
4 (P/N AA148262)
NewOld
33mm
(P/N AX210052)
New
79.5mm
22
(P/N A0541116)
104
(P/N 07200040E)
103
(P/N 08053384)
Old
(P/N AA080039)
New
1 (P/N A0541131)
3
(P/N AX210052)
4 (P/N AA148449)
4
6
9
5
7
12
(P/N 08053384)
22
(P/N A1101117)
10.5mm
13.0mm
(P/N AA148262)
36.2mm
11.5mm
17.0mm33.2mm
(P/N AA148449
S. Hamano, Assistant General Manager
)
Technical Support Department
Page 81
MODIFICATION BULLETIN NO. 35 PAGE 3 OF 3
ISSUED ON: August 31, ’94
MODEL NAMEV/HzDESTINATION
Gestetner 2515Z
Nashuatec 3115
Savin 9150115/60USA, CanadaA075-15724080XXXX
Nashua 3115115/60Canada, L.AmericaA075-16Service Parts Only
Ricoh FT4415115/60USA, CanadaA075-17A292408XXXX
Ricoh FT4415110/60TaiwanA075-19A292408XXXX
Gestetner 2515Z
Nashuatec 3115
Nashua 3115220, 230-240/50Europe. etc.A075-25Service Parts OnlyA075-45Service Parts Only
To minimize the offset image problem caused by the calcium carbonate in the copy pape r, the carbon fibers
have been removed from th e ho t rolle r and in ste ad of th e carbon fibers, another filler ha s bee n ad ded.
Old P/NNew P/NDescriptionQ’ty Used
AE011007AE011035Hot Roller
1 → 1
Inter-
change-
ability
X/O1631
Parts Catalog
Index No.Page
Serial Number
S. Hamano, Assistant General Manager
Technical Support Department
Page 83
MODIFICATION BULLETIN NO. 36 PAGE 2 OF 2
ISSUED ON: November 30, ’94
MODEL NAMEV/HzDESTINATION
Gestetner 2515Z
Nashuatec 3115
Savin 9150115/60USA, CanadaA075-15Service Parts Only
Nashua 3115115/60Canada, L.AmericaA075-16Service Parts Only
Ricoh FT4415115/60USA, CanadaA075-17Service Parts Only
Ricoh FT4415110/60TaiwanA075-19Service Parts Only
Gestetner 2515Z
Nashuatec 3115
Nashua 3115220, 230-240/50Europe. etc.A075-25Service Parts OnlyA075-45Service Parts Only
infotec 9215220, 230-240/50EuropeA075-26Service Parts OnlyA075-46Service Parts Only
Ricoh FT4415220, 230-240/50Europe, etc.A075-27Service Parts OnlyA075-47Service Parts Only
Ricoh FT4415220, 230-240/60Phillipin, etc.A075-28Service Parts Only
Ricoh FT4415220, 230-240/50AsiaA075-29Service Parts Only
115/60Canada, L. AmericaA075-10Service Parts Only
220, 230-240/50Europe etc.A075-22Service Parts OnlyA075-42Service Parts Only
JAPAN PRODUCTIONRIF PRODUCTION
CODESERIAL NUMBERCODESERIAL NUMBER
Page 84
M. Iwasa, Manager
Technical Support Department
MODIFICATION BULLETIN NO. 37 PAGE 1 OF 2
ISSUED ON: July 15, ’95
ModelN210Volt/Hz
Modified ArticlePhotointerruptor
Reason for
Due to parts standardization
Modification
Draw
No.
Old Parts
No.
AW020073AW020075Photointerruptor
AW020021AW020075Photointerruptor
A0482632Paper End Sensor Bracket
New Parts
No.
A0482635Paper Lift Sensor Bracket
DescriptionRank
Q’ty Used
Old→New
1 → 1
1 → 1
1 → 1
1 → 1
1 → 0
0 → 1
Date of
Modification
Inter-
change-
ability
O/O2137
O/O1537
O/O1635
X/X1635
X/X1835
Parts needed for replacement by new part
Part No.DescriptionNo.Page
O/O as a set1835
Serial
Number
Parts
Catalog
Page 85
MODIFICATION BULLETIN NO. 37 PAGE 2 OF 2
ISSUED ON: July 15, ’95
MODEL NAMEV/HzDESTINATION
Gestetner 2515Z
Nashuatec 3115
Savin 9150115/60USA, CanadaA075-15Service Parts Only
Nashua 3115115/60Canada, L.AmericaA075-16Service Parts Only
Ricoh FT4415115/60USA, CanadaA075-17Service Parts Only
Ricoh FT4415110/60TaiwanA075-19Service Parts Only
Gestetner 2515Z
Nashuatec 3115
Nashua 3115220, 230-240/50Europe. etc.A075-25Service Parts OnlyA075-45Service Parts Only
infotec 9215220, 230-240/50EuropeA075-26Service Parts OnlyA075-46
Ricoh FT4415220, 230-240/50Europe, etc.A075-27Service Parts OnlyA075-47
Ricoh FT4415220, 230-240/60Phillipin, etc.A075-28Service Parts Only
Ricoh FT4415220, 230-240/50AsiaA075-29Service Parts Only
115/60Canada, L. AmericaA075-10Service Parts Only
220, 230-240/50Europe etc.A075-22Service Parts OnlyA075-42
JAPAN PRODUCTIONRIF PRODUCTION
CODESERIAL NUMBERCODESERIAL NUMBER
Page 86
MODIFICATION BULLETIN NO. 38 PAGE 1 OF 2
ISSUED ON: July 31, ’95
ModelN210Volt/Hz
Modified ArticleLower Guide Plate
Reason for
Due to parts standardization
Modification
Due to parts standardization, the Lower Guide Plate has been changed.