Ricoh A054 Modification Bulletin FT4421

Page 1
MODIFICATION BULLETIN NO. 1 Page 1 of 1 ISSUED ON: April 30, ’91
Model N230 Volt/Hz
Modified Article Seals
Reason for
Parts Catalog Correction
Modification
The following seals have been added to the lens shielding cover and original length sensor from the first mass production. These seals are used to prevent light flares that cause lighter image in enlarge mode. The small lens shielding seal (#A0541756) was not previously put on any mass production machines. Please correct your catalog as shown in the following table:
P/N Description Index No. Page No. Q’ty A0541752 Shielding Plate Seal - Upper #50 21 0 - 1 A0541812 Shielding Plate Seal - Lower #51 21 0 - 1 A0541759 Lens Cover Seal - Large #52 21 0 - 1 A0541760 Lens Cover Seal - Small #53 21 0 - 1
Date of
Modification
Serial Number
A0541756 Small Lens Shielding Seal 49 21 1 - 0
#51
T .Ito, Manager Copier Technical Support
Page 2
MODIFICATION BULLETIN NO. 2 Page 1 of 3 ISSUED ON: April 30, ’91
Model N230 Volt/Hz
Modified Article Edging
Reason for
Modification
Draw
No.
Old Parts
No.
Date of
Modification
To increase safety
New Parts
No.
A0541173 Edging - 269 mm 0 - 1 #44 9 A0541174 Edging - 110 mm 0 - 1 #45 9 A0541175 Edging - 69 mm 0 - 1 #46 9 A0541180 Edging - 48 mm 0 - 1 #47 9
Description
A.B.C. Q’ty Used
Old
Rank Part No. Description Index No. Page
New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
# : New Index No.
Serial Number
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhall. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 3
MODIFICATION BULLETIN NO. 2 Page 2 of 3 ISSUED ON: April 30, ’91
DETAILS OF MODIFICATION
The edgings (plastic edge protectors) have been added to the lower front side of the main frame. This prevents the customer or customer engineer from being injured by the sharp edge.
#44
T.Ito, Manager Copier Technical Support
Page 4
MODIFICATION BULLETIN NO. 2 Page 3 of 3 ISSUED ON: April 30, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010200180
Nashua 3120 115/60 Canada, L. America A054-16 From first production Ricoh FT4421 115/60 USA, Canada A054-17 2761020141 Ricoh FT4421 110/60 Taiwan A054-19 276104XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From first production
infotec 9122Z 220,240/50 Europe A054-26 3A40210051 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761020990 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276104XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761022618
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 5
MODIFICATION BULLETIN NO. 3 Page 1 of 4 ISSUED ON: June 15, ’91
Model N230 Volt/Hz
Modified Article Cassette Holders
Reason for
To facilitate servicing
Modification
Draw
No.
Old Parts
No.
A0546739 Front Cassette Holder - 3rd Feed 1 - 0 45 25
A0546740 Rear Cassette Holder - 3rd Feed 1 - 0 44 25
New Parts
No.
- Savin -
A0546732 Front Lower Cassette Holder 0 - 1 O/X #48 25 A0546730 Front Upper Cassette Holder 0 - 1 O/X #49 25
Description
Date of
Modification
A.B.C. Q’ty Used
Old
Rank Part No. Description Index No. Page
New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
Serial Number
A0546742 Rear Lower Cassette Holder 0 - 1 O/X #46 25 A0546741 Rear Upper Cassette Holder 0 - 1 OX #47 25
# : New Index No.
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhaul. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 6
MODIFICATION BULLETIN NO. 3 Page 2 of 4 ISSUED ON: June 15, ’91
Draw
No.
Old Parts
No.
A0542697 Front Cassette Holder - 3rd Feed 1 - 0 45 25
A0542696 Rear Cassette Holder - 3rd Feed 1 - 0 44 25
A0546139 Front Cassette Holder - 3rd Feed 1 - 0 45 25
New Parts
No.
- Ricoh -
A0542732 Front Lower Cassette Holder 0 - 1 O/X #48 25 A0542730 Front Upper Cassette Holder 0 - 1 O/X #49 25
A0542742 Rear Lower Cassette Holder 0 - 1 O/X #46 25 A0542741 Rear Upper Cassette Holder 0 - 1 O/X #47 25
- Infotec -
A0546132 Front Lower Cassette Holder 0 - 1 O/X #48 25
Description
A.B.C. Q’ty Used
Old
Rank Part No. Description Index No. Page
New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
# : New Index No.
A0546130 Front Upper Cassette Holder 0 - 1 O/X #49 25
A0546140 Rear Cassette Holder - 3rd Feed 1 - 0 44 25
A0546142 Rear Lower Cassette Holder 0 - 1 O/X #46 25 A0546141 Rear Upper Cassette Holder 0 - 1 O/X #47 25
# : New Index No.
Page 7
MODIFICATION BULLETIN NO. 3 Page 3 of 4 ISSUED ON: June 15, ’91
DETAILS OF MODIFICATION
To facilitate servicing, the cassette holders have been divided into two parts as shown in the illustration.
#49
44
45
T.Ito, Manager Copier Technical Support
Page 8
MODIFICATION BULLETIN NO. 3 Page 4 of 4 ISSUED ON: June 15, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010200180
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761020141 Ricoh FT4421 110/60 Taiwan A054-19 276104XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25
infotec 9122Z 220,240/50 Europe A054-26 3A40210051 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761020990 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276104XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761022618
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 9
MODIFICATION BULLETIN NO. 4 Page 1 of 2 ISSUED ON: June 15, ’91
Model N230 Volt/Hz
Modified Article Toner Supply Clutch
Reason for
Parts Catalog Correction
Modification
The magnetic type clutch for the toner supply mechanism has been used from the first mass production machines. The part number in the parts catalog is for the spring type clutch. Please correct your ca talog as follows:
Incorrect P/N Correct P/N Description
A0485263 AX210024 Toner Supply Clutch 3 57
AA148301 AA148262 Toner Supply Shaft 4 57
A0481135 A0549500 Toner Supply Bracket 1 57
A0549502
Toner Supply Clutch Stopper
Index
No.
#114 57
Page
No.
Date of
Modification
Serial Number
08053384 Bushing - 4M 103 57
A0549501 Bushing - 4M # 21 57
# : New Index No.
Page 10
MODIFICATION BULLETIN NO. 4 Page 2 of 2 ISSUED ON: June 15, ’91
1
# 21
4
3
#114
1
4
3
T .Ito, Manager Copier Technical Support
Page 11
MODIFICATION BULLETIN NO. 5 Page 1 of 3 ISSUED ON: June 15, ’91
Model N230 Volt/Hz
Modified Article Toner Supply Clutch
Reason for
To facilitate servicing
Modification
Draw
No.
Old Parts
No.
A0549500 Toner Supply Bracket 1 - 0 1 57 A0549502 Toner Supply Clutch Stopper 1 - 0 114 57
A0549501 Bushing - 4M 1 - 0 21 57
New Parts
No.
A0541116 Toner Supply Clutch Ass’y 0 - 1 # 22 57
A0541135 Toner Supply Bracket 0 - 1 X/X 1 57
AA080039 Bushing - 3M 0 - 1 X/X 21 57
Description
Date of
Modification
A.B.C. Q’ty Used
Old
Rank Part No. Description Index No. Page
New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
Serial Number
# : New Index No.
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhall. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 12
MODIFICATION BULLETIN NO. 5 Page 2 of 3 ISSUED ON: June 15, ’91
DETAILS OF MODIFICATION
To facilitate servicing, the toner supply bracket [A] and the toner supply clutch stopper [B] have been combined into one part [C], and the shape of the bushing was changed as shown. The old and new parts are not interchangeable. They are interchangeable as a set. (Please use the new parts when the old parts are replaced.) To facilitate servicing, the toner supply clutch assembly has been resistered as a service part.
[A]
[C]
[B]
12
4
7
4
6
9
T.Ito, Manager Copier Technical Support
Page 13
MODIFICATION BULLETIN NO. 5 Page 3 of 3 ISSUED ON: June 15, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010400371
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761040001 Ricoh FT4421 110/60 Taiwan A054-19 276104XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761040231 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 2761040779 Ricoh FT4421 220,240/50 Asia A054-29 2761040784
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 14
MODIFICATION BULLETIN NO. 6 Page 1 of 3 ISSUED ON: June 15, ’91
Model N230 Volt/Hz
Modified Article Fusing Cover
Reason for
To reduce dog-eared copies
Modification
Draw
No.
Old Parts
No.
A0484151 A0484155 Fusing Cover 1 - 1 X/O 1 41
New Parts
No.
Description
Date of
Modification
A.B.C. Q’ty Used
Old
Rank Part No. Description Index No. Page
New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
Serial Number
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhall. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 15
MODIFICATION BULLETIN NO. 6 Page 2 of 3 ISSUED ON: June 15, ’91
DETAILS OF MODIFICATION
Dog ear may appear on the leading edge of paper. This is caused by the curled leading edge [A] contacting the paper guide [B] on the fusing cover. This problem tends to occur in the duplex mode. The length of the paper guide of the fusing cover has been extended by 10 mm as shown.
[B]
10 mm
Drum
[A]
Paper
T.Ito, Manager Copier Technical Support
Page 16
MODIFICATION BULLETIN NO. 6 Page 3 of 3 ISSUED ON: June 15, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010500711
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761050001 Ricoh FT4421 110/60 Taiwan A054-19 276106XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761040233 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276106XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761050094
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 17
MODIFICATION BULLETIN NO. 7 Page 1 of 3 ISSUED ON: June 15, ’91
Model N230 Volt/Hz
Modified Article Front Cover Chain
Reason for
To improve durability
Modification
Draw
No.
Old Parts
No.
A0171286 A0481285 Front Cover Chain 1 - 1 X/O 21 9
New Parts
No.
Description
Date of
Modification
A.B.C. Q’ty Used
Old
Rank Part No. Description Index No. Page
New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
Serial Number
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhaul. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 18
MODIFICATION BULLETIN NO. 7 Page 2 of 3 ISSUED ON: June 15, ’91
DETAILS OF MODIFICATION
To improve durability of the chain, the material of it has been changed form resin to metal.
T.Ito, Manager Copier Technical Support
Page 19
MODIFICATION BULLETIN NO. 7 Page 3 of 3 ISSUED ON: June 15, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010400439
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761050001 Ricoh FT4421 110/60 Taiwan A054-19 276105XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761040231 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276105XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761050094
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 20
MODIFICATION BULLETIN NO. 8 Page 1 of 2 ISSUED ON: June 30, ’91
Model N230 Volt/Hz
Modified Article Drum Holder
Reason for
To ensure drum ground
Modification
Old P/N New P/N Description
A0062260 A0482258 Drum Holder 1- 1 X/O 18 35
03140200W 03140200B Philips Pan Head Screw - M4X25 2 - 2 X/O 104 35
Q’ty Used
Old New
Interchangeability Index No. Page
To ensure drum ground, the surface treatment of the drum holder has been changed from zinc galvanizing to nickel plating.
Date of
Modification
Serial Number
T.Ito, Manager Copier Technical Support
Page 21
MODIFICATION BULLETIN NO. 8 Page 2 of 2 ISSUED ON: June 30, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010500711
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761050001 Ricoh FT4421 110/60 Taiwan A054-19 276105XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 3A40610001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761040231 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276105XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761050094
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 22
MODIFICATION BULLETIN NO. 9 Page 1 of 2 ISSUED ON: June 30, ’91
Model N230 Volt/Hz
Modified Article Main Board & Eraser
Reason for
To improve erase function
Modification
Old P/N New P/N Description
A0545102 A0545120 Main Board 1 - 1 X/X 5 63 A0545104 A0545125 IC-D27512 - V05 1 - 1 X/X 2 65 A0485275 A0485230 Eraser 1 - 1 X/X 34 55 A0482061 A0485820 Eraser Bracket 1 - 1 X/X 36 55
11024208 CT Header - 9P 2 - 1 109 65
Q’ty Used
Old New
Interchangeability Index No. Page
Date of
Modification
Serial Number
11024626 Connetor - 9P 1 - 2 X/X 123 65
To improve the erase function, the eraser and the main board have been changed.
1. The number of the LEDs has been changed from 35 pcs to 43 pcs.
2. The main board has been modified for the new erase function. The old and new part are not interchangeable individually, but they are interchangeable as a set . NOTE: To make distinguishing the new part from the old one easier, the color of the connectors of the era ser
and on the main board has been changed from "White" to "Blue".
T.Ito, Manager Copier Technical Support
Page 23
MODIFICATION BULLETIN NO. 9 Page 2 of 2 ISSUED ON: June 30, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010500711
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761050001 Ricoh FT4421 110/60 Taiwan A054-19 276106XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 3A40610001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761050042 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276106XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761050094
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 24
MODIFICATION BULLETIN NO. 10 Page 1 of 3 ISSUED ON: June 30, ’91
Model N230 Volt/Hz
Modified Article Rubber Cushion
Reason for
To ensure the connection between the main board and interface board connectors
Modification
Draw
No.
Old Parts
No.
New Parts
No.
54461098 Rubber Cushion 0 - 1 #26 61
Description
Date of
Modification
A.B.C. Q’ty Used
Old
Rank Part No. Description Index No. Page
New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
# : New Index No.
Serial Number
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhaul. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 25
MODIFICATION BULLETIN NO. 10 Page 2 of 3 ISSUED ON: June 30, ’91
DETAILS OF MODIFICATION
If the DF harness is not routed properly, the rear cover may press the DF harness against the interface board when the rear cover is closed. This might cause the interface board connector to come off from the main board connector, which would clear RAM memory. To ensure the connection, the rubber cushion has been adhered on the main board as shown in the illustration.
NOTE: The DF harness must be routed correctly. Please refer to RTB No. 002 for the details.
T.Ito, Manager Copier Technical Support
Page 26
MODIFICATION BULLETIN NO. 10 Page 3 of 3 ISSUED ON: June 30, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010500711
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761050001 Ricoh FT4421 110/60 Taiwan A054-19 276105XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 3A40610001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761040231 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276105XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761050094
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 27
MODIFICATION BULLETIN NO. 11 Page 1 of 2 ISSUED ON: June 30, ’91
Model N230 Volt/Hz
Modified Article Dust Proof Glass
Reason for
To facilitate servicing
Modification
Old P/N New P/N Description
A0481875 A0481877 Dust Proof Glass
Q’ty Used
Old New
1 1
Interchangeability Index No. Page
X/O 35 55
To facilitate servicing, the spectral characteristics of the filter on the dust proof glass has been changed. The light intensity passing through the filter has been increased. With the new filter, the adjustment value of the SP mode #48 (exposure lamp intensity adjustment) at the factory has been decreased. This increases the adjustment rarge of SP mode #48 in the field.
Date of
Modification
Serial Number
T.Ito, Manager Copier Technical Support
Page 28
MODIFICATION BULLETIN NO. 11 Page 2 of 2 ISSUED ON: June 30, ’91
JAPAN PRODUCTION RIF PRODUCTION
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010400371
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761040001 Ricoh FT4421 110/60 Taiwan A054-19 276105XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
infotec 9122Z 220,240/50 Europe A054-26 3A40610001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761040231 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 2761040779 Ricoh FT4421 220,240/50 Asia A054-29 2761040784
Page 29
MODIFICATION BULLETIN NO. 12 Page 1 of 3 ISSUED ON: June 30, ’91
Model N230 Volt/Hz
Modified Article Drum Support Plate
Reason for
To facilitate servicing
Modification
Draw
No.
Old Parts
No.
A0482260 Drum Support Plate 0 - 1 17 35 A0482263 Front Drum Side Plate 0 - 1 16 35
New Parts
No.
A0482254 Drum Support Plate Ass’y 1 - 1 X/O #43 35
Description
Date of
Modification
A.B.C. Q’ty Used
Old
Rank Part No. Description Index No. Page
New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
# : New Index No.
Serial Number
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhaul. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 30
MODIFICATION BULLETIN NO. 12 Page 2 of 3 ISSUED ON: June 30, ’91
DETAILS OF MODIFICATION
The PG gap is preset with special tools at the factory and the screws securing the drum support plat e and front drum side plate are paint locked. Basically, those parts should not be removed except when they are being replaced. To make part replacement easier, the service parts have been changed as follows:
The drum support plate assembly, consisting of the drum side plate and the front drum side plate, ha s been registered as a service part instead of the component parts. (For the details, please refer to RTB #4.) The drum support plate an d the front drum side plate are no longer abailable as service parts.
NOTE: Do not loosen or remove the screws [A] which are paint locked.
Two screw holes [B] have been added to the drum side plate so that the drum support plate assembly can be replaced.
[B]
16
[A]
17
T.Ito, Manager Copier Technical Support
Page 31
MODIFICATION BULLETIN NO. 12 Page 3 of 3 ISSUED ON: June 30, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010600896
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761060001 Ricoh FT4421 110/60 Taiwan A054-19 276107XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 3A40610001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761060674 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276107XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761060754
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 32
MODIFICATION BULLETIN NO. 13 Page 1 of 2 ISSUED ON:June 30, ’91
Model N230 Volt/Hz
Modified Article Small Cassette Cover
Reason for
Parts Standardization
Modification
Due to parts standardization, the following parts have been changed.
Old P/N New P/N Description interchangeability Page Index A0082737 A0602955 Small Cassette Cover (Ricoh) O/O 19 23 52156446 52156676 Small Cassette Cover (NSA, KAL, Savin) O/O 19 23
Date of
Modification
Serial Number
T. Ito, Manager Copier Technical Support
Page 33
MODIFICATION BULLETIN NO. 13 Page 2 of 2 ISSUED ON:June 30, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010300191
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761030001 Ricoh FT4421 110/60 Taiwan A054-19 276105XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 3A40610001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761030261 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 2761040779 Ricoh FT4421 220,240/50 Asia A054-29 2761030461
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 34
MODIFICATION BULLETIN NO. 14 Page 1 of 2 ISSUED ON: June 30, ’91
Model N230 Volt/Hz
Modified Article Shield Mylar
Reason for
To decrease the possibility of a dirty background copy
Modification
New P/N Description
A0482055 Shield Mylar 0 - 1 #42 55
Q’ty Used
Old New
Index No. Page
# : New Index No.
To decrease that the 6th mirror and the filter on the dust proof glass get dirty with dust, which ma y cause dirty background copy prematurely, a shield mylar has been added as shown.
Date of
Modification
Serial Number
6th Mirror
T.Ito, Manager Copier Technical Support
Page 35
MODIFICATION BULLETIN NO. 14 Page 2 of 2 ISSUED ON: June 30, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010400371
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761040001 Ricoh FT4421 110/60 Taiwan A054-19 276106XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 3A4061XXXX A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761040231 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 2761040779 Ricoh FT4421 220,240/50 Asia A054-29 2761040784
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 36
MODIFICATION BULLETIN NO. 15 Page 1 of 2 ISSUED ON: June 30, ’91
Model N230 Volt/Hz
Modified Article Shield Mylar
Reason for
To improve assemblying procedure at the factory
Modification
Old P/N New P/N Description
A0482055 A0482058 Shield Mylar 1 - 1 X/O 42 55
Q’ty Used
Old New
Interchangeability Index No. Page
To improve asseblying procedure at the factory, the shape of the shield mylar has been cahnged as fo llows:
Date of
Modification
Serial Number
T.Ito, Manager Copier Technical Support
Page 37
MODIFICATION BULLETIN NO. 15 Page 2 of 2 ISSUED ON: June 30, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010500711
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761050001 Ricoh FT4421 110/60 Taiwan A054-19 276106XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 3A4061XXXX A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761040380 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276106XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761050094
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 38
MODIFICATION BULLETIN NO. 16 Page 1 of 2 ISSUED ON: June 30, ’91
Model N230 Volt/Hz
Modified Article Ferrite Core
Reason for
To improve CPU malfunction
Modification
New P/N Description
16070478 Ferrite Core - RISC - 5 - F 0 - 3 #44 59
Q’ty Used
Old New
Index No. Page
To improve CPU malfunction due to T&S corona leakage, the ferrite cores have been installed on the T&S corona cables as shown.
Date of
Modification
# : New Index No.
Serial Number
T.Ito, Manager Copier Technical Support
Page 39
MODIFICATION BULLETIN NO. 16 Page 2 of 2 ISSUED ON: June 30, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010500711
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761050001 Ricoh FT4421 110/60 Taiwan A054-19 276106XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production
infotec 9122Z 220,240/50 Europe A054-26 3A40610001 A054-46 From First Production Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761040231 A054-47 From First Production Ricoh FT4421 220,240/60 Philippines, etc. A054-28 2761040779 Ricoh FT4421 220,240/50 Asia A054-29 2761040784
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 40
MODIFICATION BULLETIN NO. 17 Page 1 of 3 ISSUED ON: July 15, ’91
Model N230 Volt/Hz
Modified Article Drive Roller Knob
Reason for
To facilitate removal of misfed paper
Modification
Draw
No.
Old Parts
No.
AG050047 AG050056 Drive Roller Knob 1 - 1 X/O 15 25
New Parts
No.
Description
Date of
Modification
A.B.C.
Rank Part No. Description Index No. Page
Q’ty Used
Old New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
Serial Number
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts t tim f overhaul. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 41
DETAILS OF MODIFICATION
MODIFICATION BULLETIN NO. 17 Page 2 of 3 ISSUED ON: July 15, ’91
The shape of the drive roller knob has been changed for the following reasons:
To facilitate removal of misfed paper
(A customer can rotate the drive roller more easily to remove misfed paper.)
To ensure the engagement between the ratchet [A] and the relay roller drive
gear [B].
[A]
[A]
#AB013445
[A]
[B]
16 mm
20 mm
T.Ito, Manager Copier Technical Support
Page 42
MODIFICATION BULLETIN NO. 17 Page 3 of 3 ISSUED ON: July 15, ’91
JAPAN PRODUCTION RIF PRODUCTION
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 801080XXXX
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761070001 Ricoh FT4421 110/60 Taiwan A054-19 276108XXXX
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
Nashua 3120 220,240/50 Europe. etc. A054-25 2451070001 infotec 9122Z 220,240/50 Europe A054-26 3A40710001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761071256 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276108XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761071656
Page 43
MODIFICATION BULLETIN NO. 18 Page 1 of 3 ISSUED ON: July 15, ’91
Model N230 Volt/Hz
Modified Article T&S Corona Unit
Draw
No.
Reason for
Modification
Old Parts
No.
A0483876 A0483921 T&S Corona Unit 1 - 1 X/O 1 41 A0483877 A0483881 T&S Corona Guide 1 - 1 X/O 2 41 AD023057 AD023078 T&S Corona Unit Casing 1 - 1 X/X A0483888 A0483922 T&S Corona Guide Plate 1 - 1 X/X 13 41
1. To improve duplex copy quality
2. To reduce the possibility of corona current leakage
New Parts
No.
Description
Date of
Modification
A.B.C.
Rank Part No. Description Index No. Page
Q’ty Used
Old New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
X/O as a set
Serial Number
12 41
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhaul. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 44
MODIFICATION BULLETIN NO. 18 Page 2 of 3 ISSUED ON: July 15, ’91
DETAILS OF MODIFICATION
1. To improve duplex copy quality, the T&S corona unit casing has been changed as shown in the illus tration. The mylar on the T&S corona guide plate has been changed to a conductive material.
2. To reduce the possibility of corona current leakage, the distance [A] between the separation coro na wire [B] and the guide [C] has been increased by changing the shape of the guide as shown.
[C]
OLD
3 mm
[A]
NEW
12 mm
[B]
3.6 mm
9 mm
T.Ito, Manager Copier Technical Support
Page 45
MODIFICATION BULLETIN NO. 18 Page 3 of 3 ISSUED ON: July 15, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 Ricoh FT4421 110/60 Taiwan A054-19
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Nashua 3120 220,240/50 Europe. etc. A054-25 2451060001 infotec 9122Z 220,240/50 Europe A054-26 3A40610001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761050042 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 Ricoh FT4421 220,240/50 Asia A054-29
Page 46
Model N230
Modified Article T&S Corona Unit
Reason for
To reduce the possibility of corona current leakage
Modification
MODIFICATION BULLETIN NO. 19
Page 1 of 3 ISSUED ON: July 15, ’91
Date
Volt/Hz
Modification
of
Serial Number
Draw
No. No.
Old Parts
A0483876 A0483879 A0483877
New Parts
No.
A0483881
A.B.C.
Description Old -
Rank
T&S Corona Unit 1-1 T&S Corona Guide 1-1
Q’ty Used lnter-
New
change-
ability
X/O X/O
Part needed for replacement by new part
Part No.
Description
Parts Catalog
Index No. Page
1
2
41 41
Rank: A: Replace with new parts immediately. B: Replace with new parts at time of repair. C : Replace with new parts at time of overhaul.
Interchangeability:
(I) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in “Parts needed for replacement by new part” to
install the new part.
(2) The mark to the left of the slash indicates whether the old part can be
in the old machine. x = Not interchangeable o = Interchangeable
used in the new machine, and the mark to the right indicates whether the new part can be used
Page 47
MODIFICATION BULLETIN NO. 19
DETAILS OF MODIFICATION
To reduce the possibility of corona current leakage, the distance [A] between the separation corona wire [B] and the guide
[C] has been increased by changing the shape of the guide as shown. WIth this modification, the part number of the T&S corona unit has been changed.
Page 2 of 3
ISSUED ON:
[c]
[A]
July 15,’91
[B]
T.lto, Manager Copier Technical Support
Page 48
MODIFICATION BULLETIN NO. 19
Page
3 of 3
ISSUED ON:
July 15,’91
MODEL NAME
Savin
9210
Nashua 3120
Ricoh
FT4421 115/60
Ricoh
FT4421 110/60 Taiwan Nashua 3120 infotec9122Z 220,240/50
Ricoh FT4421 Ricoh FT4421 Ricoh
FT4421
V/Hz DESTINATION
115/60 115/60
220,240/50
220,240/50 220,240/60 220,240/50 Asia A054-29 2761050094
Canada, L. America
JAPAN PRODUCTION
CODE
USA, Canada A054-15 8010600896
A054-16
USA, Canada A054-17
A054-19 276106XXXX
Europe. etc.
Europe
Europe, etc.
Philippines, etc. A054-28 276106XXXX
A054-25 A054-26 A054-46 A054-27
SERIAL NUMBER
2761060001
CODE
A054-47
RIF
PRODUCTION
SERIAL NUMBER
Page 49
MODIFICATION BULLETIN NO. 20 Page 1 of 1 ISSUED ON: September 15, ’91
Model N230 Volt/Hz
Modified Article Development Drive Clutch
Reason for
To ensure the clutch function
Modification
To ensure the development drive clutch function, the internal diameter of the spring in the clutch h as been changed from 13.82 mm to 13.78 mm.
Old P/N New P/N Description
AB040007 AB040011 Development Drive Clutch 1 - 1 X/O 3 51
Q’ty Used
Old New
Interchangeability Index No. Page No.
NOTE: To distinguish the new part from the old one, the color of the gear on the clutch has been changed from "White" to "Black".
Date of
Modification
Serial Number
T .Ito, Manager Copier Technical Support
Page 50
MODIFICATION BULLETIN NO. 20 Page 2 of 1 ISSUED ON: September 15, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010800911
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761070001 Ricoh FT4421 110/60 Taiwan A054-19 276108XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 2451070001 infotec 9122Z 220,240/50 Europe A054-26 3A40710001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761071256 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276108XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761071656
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 51
MODIFICATION BULLETIN NO. 21 Page 1 of 3 ISSUED ON: September 15, ’91
Model N230 Volt/Hz
Modified Article Transport guide
Reason for
To prevent thick paper from being misfed
Modification
Draw
No.
Old Parts
No.
AA020003 AA020013 Magnet Catch - Transport Guide 2 - 2 X/X 6 27 A0482664 A0482663 Front Guide Pate Holder 1 - 1 X/X 1 29 A0482665 A0482666 Rear Guide Plate Holder 1 - 1 X/X 2 29 A0482645 A0482649 Transport Guide Plate 1 - 1 X/O 7 27
52032679 Pinion Tightening Screw - M4x5 2 - 1 34 27
New Parts
No.
Description
Date of
Modification
A.B.C.
Rank Part No. Description Index No. Page
Q’ty Used
Old New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
Serial Number
X/O as a set
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhaul. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 52
MODIFICATION BULLETIN NO. 21 Page 2 of 3 ISSUED ON: September 15, ’91
DETAILS OF MODIFICATION
When thick paper is fed from the paper tray, the turn guide plate is pressed by the paper and may sw ing out. This causes paper misfeed. To prevent thick paper from being misfed, the magnet catches and front and rear guide plate holders have been changed to increase the power of the magnet catch. To make servicing easier, the shape of the turn guide plate hinge has been changed as shown.
Index #2
Index #7
Index #6
Index #1
T.Ito, Manager Copier Technical Support
Page 53
MODIFICATION BULLETIN NO. 21 Page 3 of 3 ISSUED ON: September 15, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010800911
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761070451 Ricoh FT4421 110/60 Taiwan A054-19 276108XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 2451070246 infotec 9122Z 220,240/50 Europe A054-26 3A40710040 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761071336 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276108XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761071776
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 54
MODIFICATION BULLETIN NO. 22 Page 1 of 2 ISSUED ON: September 15, ’91
Model N230 Volt/Hz
Modified Article T/S Corona Receptacle
Reason for
To facilitate servicing
Modification
Date of
Modification
The ferrite cores have been installed on the T&S corona cables. (Please refer to MB #16.) To facilitate servicing, the ferrite cores and the T&S corona receptacle has been combined into a si ngle part as shown in the illustration.
Old P/N New P/N Description
AD021059 AD021079 T/S Corona Receptacle 1 - 1 X/O 26 59
16070478 Ferrite Core - RISC - 5 - F 3 - 0 44 59
Q’ty Used
Old New
Interchangeability Index No. Page No.
NOTE: The ferrite core (#16070478) is still available as a service part.
Serial Number
#16070478
Ferrite Core
Ferrite Core
T.Ito, Manager Copier Technical Support
Page 55
MODIFICATION BULLETIN NO. 22 Page 2 of 2 ISSUED ON: September 15, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010800911
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761070001 Ricoh FT4421 110/60 Taiwan A054-19 276108XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 2451070001 infotec 9122Z 220,240/50 Europe A054-26 3A40710001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761071256 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276108XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761071656
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 56
Reissued on : November 15, ’91
MODIFICATION BULLETIN NO. 23 Page 1 of 2 ISSUED ON: October 15, ’91
Model N230 Volt/Hz
Modified Article Main Board and ROM (Service Parts Only)
Reason for
Software Modification
Modification
Date of
Modification
The software has been modified to improve the following problems for the ROM, which is used on the m achines produced before applying the modification to improve the erase function. (Refer to MB #9 for the cut-in seria l numbers.)
1. Black copy
2. Service Call 12 (Refer to MB #10 for the details.) The part numbers of the main board and ROM only for the service parts have been changed as shown bel ow:
Old P/N New P/N Description
#A0545102 #A0545130 Main Board 1 - 1 X/O
Q’ty Used
Old New
Interchangeability Index No. Page No.
5 *
Serial Number
63 65
#A0545104 ROM 2 65
#A0545136 IC - TMM27512AD-20 1 - 1 X/O 2 65
NOTE: The software of the new ROM (#A0545125) used on the production has been modified to improve the abov e
problems.
T .Ito, Manager Copier Technical Support
Page 57
Reissued on : November 15, ’91
MODIFICATION BULLETIN NO. 23 Page 2 of 2 ISSUED ON: October 15, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 Service Parts Only
Nashua 3120 115/60 Canada, L. America A054-16 Service Parts Only Ricoh FT4421 115/60 USA, Canada A054-17 Service Parts Only Ricoh FT4421 110/60 Taiwan A054-19 Service Parts Only
Nashua 3120 220,240/50 Europe. etc. A054-25 Service Parts Only
infotec 9122Z 220,240/50 Europe A054-26 Service Parts Only A054-46 Service Parts Only Ricoh FT4421 220,240/50 Europe, etc. A054-27 Service Parts Only A054-47 Service Parts Only Ricoh FT4421 220,240/60 Philippines, etc. A054-28 Service Parts Only Ricoh FT4421 220,240/50 Asia A054-29 Service Parts Only
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 58
MODIFICATION BULLETIN NO. 24 Page 1 of 3 ISSUED ON: October 15, ’91
Model N230 Volt/Hz
Modified Article Parts Catalog
Reason for
Parts Catalog Correction
Modification
Please correct your catalog as shown below:
1. Incorrect Index No.
P/N Description
AF020195 Upper Turn Roller 36 40 45 AF020155 Lower Turn Roller 40 36 45
Incorrect Index
No.
2. Part number missing
Date of
Modification
Correct Index No. Page No.
Serial Number
P/N Description Index No. Page No. A0541761 Shielding Plate Seal - Small #54 21 A0482658 Mylar - Transport Guide Bracket #46 27
# : New Index Number
T .Ito, Manager Copier Technical Support
Page 59
3. Incorrect part number
Incorrect P/N Correct P/N Description Index No. Page No.
AX070007 AX000007 Paper Feed Solenoid 38 27
MODIFICATION BULLETIN NO. 24 Page 2 of 3 ISSUED ON: October 15, ’91
#54 #46
Page 60
MODIFICATION BULLETIN NO. 24 Page 3 of 3 ISSUED ON: October 15, ’91
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 Ricoh FT4421 110/60 Taiwan A054-19
Nashua 3120 220,240/50 Europe. etc. A054-25 infotec 9122Z 220,240/50 Europe A054-26 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 Ricoh FT4421 220,240/50 Asia A054-29
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 61
MODIFICATION BULLETIN NO. 25 Page 1 of 2 ISSUED ON: October 15, ’91
Model N230 Volt/Hz
Modified Article Magnet Plate
Reason for
Part Standardization
Modification
Date of
Modification
For part standardization, the magnet plate has been changed. The shape of the magnet plate is differ ent for the old and new parts. They are completely interchangeable.
Old P/N New P/N Description
A0171285 A0481311 Magnet Plate 1 - 1 O/O 29 9
Q’ty Used
Old New
Interchangeability Index No. Page No.
Serial Number
T.Ito, Manager Copier Technical Support
Page 62
MODIFICATION BULLETIN NO. 25 Page 2 of 2 ISSUED ON: October 15, ’91
JAPAN PRODUCTION RIF PRODUCTION
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010800915
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 276110XXXX Ricoh FT4421 110/60 Taiwan A054-19 276110XXXX
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
Nashua 3120 220,240/50 Europe. etc. A054-25 From First Production infotec 9122Z 220,240/50 Europe A054-26 3A4101XXXX A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 276110XXXX A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276110XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761090599
Page 63
MODIFICATION BULLETIN NO. 26 Page 1 of 2 ISSUED ON: October 15, ’91
Model N230 Volt/Hz
Modified Article Rear Heater Holder
Reason for
To prevent the fusing drive gear from heat damage
Modification
To prevent the fusing drive gear [A] from heat damage, the shape of the rear heater holder has been changed as shown.
Old P/N New P/N Description
A0484101 A0484105 Rear Heater Holder 1 - 1 X/O 5 45
Q’ty Used
Old New
Interchangeability Index No. Page No.
[A]
Date of
Modification
Serial Number
5
T .Ito, Manager Copier Technical Support
Page 64
MODIFICATION BULLETIN NO. 26 Page 2 of 2 ISSUED ON: October 15, ’91
JAPAN PRODUCTION RIF PRODUCTION
MODEL NAME V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
Savin 9210 115/60 USA, Canada A054-15 8010800911
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761080001 Ricoh FT4421 110/60 Taiwan A054-19 276109XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 2451080001 infotec 9122Z 220,240/50 Europe A054-26 3A4091XXXX A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 276109XXXX A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276109XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761090599
Page 65
MODIFICATION BULLETIN NO. 27 Page 1 of 2 ISSUED ON: October 15, ’91
Model N230 Volt/Hz
Modified Article Knob Bracket
Reason for
To set the transport guide plate correctly
Modification
The shape of the knob bracket has been changed so that the transport guide plate is correctly set to the original position.
Old P/N New P/N Description
A0482648 A0482652 Knob Bracket 1 - 1 X/O 10 27
Q’ty Used
Old New
Interchangeability Index No. Page No.
Date of
Modification
Serial Number
T .Ito, Manager Copier Technical Support
Page 66
MODIFICATION BULLETIN NO. 27 Page 2 of 2 ISSUED ON: October 15, ’91
JAPAN PRODUCTION RIF PRODUCTION
MODEL NAME V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
Savin 9210 115/60 USA, Canada A054-15 8010800911
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761080001 Ricoh FT4421 110/60 Taiwan A054-19 276109XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 2451080001 infotec 9122Z 220,240/50 Europe A054-26 3A4091XXXX A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 276109XXXX A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276109XXXX Ricoh FT4421 220,240/50 Asia A054-29 2761090599
Page 67
MODIFICATION BULLETIN NO. 28 Page 1 of 2 ISSUED ON: December 15, ’91
Model N230 Volt/Hz
Modified Article Decal
Reason for
Power source (voltage) change in Europe
Modification
Date of
Modification
The power source (voltage) is going to change from 220/240V to 230V in Europe. To change the machine specification for this voltage change, a decal has been enclosed with the machine as an accessory.
New P/N Description Q’ty Used Index No. Page No.
AA000095 Decal - Power Supply - 230V 1 * 9
* : Accessory
NOTE:
When machines produced before this modification are installed in 230V areas, the decal should be att ached on the rear cover instead of the decal for 220V.
Serial Number
#AA000095
T .Ito, Manager Copier Technical Support
Page 68
MODIFICATION BULLETIN NO. 28 Page 2 of 2 ISSUED ON: December 15, ’91
JAPAN PRODUCTION RIF PRODUCTION
MODEL NAME V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
Savin 9210 115/60 USA, Canada A054-15
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 Ricoh FT4421 110/60 Taiwan A054-19
Nashua 3120 220,240/50 Europe. etc. A054-25 2451080001 infotec 9122Z 220,240/50 Europe A054-26 3A41210001 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761101061 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 Ricoh FT4421 220,240/50 Asia A054-29
Page 69
MODIFICATION BULLETIN NO. 29 Page 1 of 5 ISSUED ON: January 31, ’92
Model N230 Volt/Hz
Modified Article Operation Panel
Reason for
To minimize the operation panel malfunction
Modification
Draw
No.
Old Parts
No.
A0545550 A0545551 Operation Panel Ass’y - LT 1 - 1 X/O * 15 A0541452 A0541552 Operation Panel Cover - LT 1 - 1 X/O 1 15 A0541500 A0541510 Operation Panle Board - LT 1 - 1 X/O 11 15 A0545650 A0545651 Operation Panel Ass’y - A4 1 - 1 X/O * 15 A0541453 A0541553 Operation Panel Cover - A4 1 - 1 X/O 1 15
New Parts
No.
Ricoh version
Description
Date of
Modification
A.B.C.
Rank Part No. Description Index No. Page
Q’ty Used
Old New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
Serial Number
A0541503 A0541513 Operation Panel Board - A4 1 - 1 X/O 11 15 A0541499 Insulating Mylar - 220/240V 1 - 0 38 15
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair. C : Replace with new parts at time of overhaul. Interchangeability: (1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for replacement by new part" to install the new part. (2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
Page 70
MODIFICATION BULLETIN NO. 29 Page 2 of 5 ISSUED ON: January 31, ’92
Draw
No.
Old Parts
No.
A0546691 A0546692 Operation Panel Ass’y 1 - 1 X/O * A0541504 A0541514 Operation Panel Board 1 - 1 X/O 11 A0546693 A0546695 Operation Panle Cover 1 - 1 X/O 1
A0546091 A0546094 Operation Panel Ass’y 1 - 1 X/O * 15 A0541503 A0541507 Operation Panel Board 1 - 1 X/O 11 15 A0546093 A0546095 Operation Panel Cover 1 - 1 X/O 1 15 A0541499 Insulating Sheet - 220/240V 1 - 0 X/O 37 15
New Parts
No.
Savin version
HCS infotec version
Description
A.B.C.
Rank Part No. Description Index No. Page
Q’ty Used
Old New
Inter-
change-
ability
Part needed for replacement by new part Parts Catalog
Page 71
MODIFICATION BULLETIN NO. 29 Page 3 of 5 ISSUED ON: January 31, ’92
(Reason of modification)
1) Operation panel board
To minimize display malfunction, 8 diodes have been added to the operation panel board. (See Fig. 1)
To make controlling parts easier, part numbers of the operation panel boards for each destination have been registered. (See Table 1)
(Fig. 1: Operation panel board schematics)
These 8 diodes are added. (D541 D548)
(Table 1: Jumper wire combination table)
Description P/N J401 J402 J403
Ricoh - LT A0541510 -- ON ON Ricoh - A4 A0541513 ON -- ON
Savin A0541514 -- -- ON
HCS infotec A0541507 -- -- --
ON: Jumper wire is connected.
Page 72
DETAILS OF MODIFICATION
2) Operation panel cover
If the operation panel cover is pressed down around the sort key area, the copier may accept th e
sort mode by error because of a warped cover. To prevent the cover from warping, a rib has been added to hold the operation panel cover to the main frame.
3) Insulating mylar (220/240V only)
It was found that the insulating mylar is not necessary, even from the view point of safety s tandard
regulators. The insulating mylar has been eliminated.
MODIFICATION BULLETIN NO. 29 Page 4 of 5 ISSUED ON: January 31, ’92
T. Ito, Manager Copier Technical Support
Page 73
MODIFICATION BULLETIN NO. 29 Page 5 of 5 ISSUED ON: January 31, ’92
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8010800911
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761070026 Ricoh FT4421 110/60 Taiwan A054-19 276202XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 infotec 9122Z 220,240/50 Europe A054-26 3A41210004 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761071256 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 2762010764 Ricoh FT4421 220,240/50 Asia A054-29 2761090599
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 74
MODIFICATION BULLETIN NO. 30 Page 1 of 2 ISSUED ON: January 31, ’92
Model N230 Volt/Hz
Modified Article Knob Collar
Reason for
To increase margin of drum ground
Modification
The bearing of the knob collar has been changed to increase margin of drum ground. Conductivity grease is lubricated into the new bearing.
Old P/N New P/N Description
AA132074 AA132153 Knob Collar 1 - 1 X/O 19 33
Q’ty Used
Old New
Date of
Modification
Interchangeability Index No. Page No.
Serial Number
T.Ito, Manager Copier Technical Support
Page 75
MODIFICATION BULLETIN NO. 30 Page 2 of 2 ISSUED ON: January 31, ’92
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8020101934
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2761110793 Ricoh FT4421 110/60 Taiwan A054-19 276202XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 2451110001 infotec 9122Z 220,240/50 Europe A054-26 3A4022XXXX A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 2761110805 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 2762010764 Ricoh FT4421 220,240/50 Asia A054-29 2761110945
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 76
Model
N230
MODIFICATION BULLETIN NO. 31
Page 1 of 2
Volt/Hz
ISSUED ON:
of
Date
Modification
.Ianuarv
31.’92
Serial Number
Modified Article
DG Gauge
Reason for
Change of the DG adjustment standard
Modification
The DG gauge has been changed to meet the new adjustment standard. (Refer to RTB -012)
Old P/N
A0489500 A0489507
New P/N
Description
DG Gauge - 0.63/0.72
Q’ty Used
Old
1-1
New
Interchangeability Index No. Page No.
X/O
1
83
Copier Technical Support
Page 77
MODEL NAME
V/Hz
MODIFICATION BULLETIN NO. 31
JAPAN PRODUCTION
DESTINATION
Page 2 of
2
RIF
ISSUED ON: January 31,’92
PRODUCTION
Savin
9210
Nashua 3120
Ricoh
FT4421
Ricoh FT4421
Nashua 3120 infotec 9122Z Ricoh
FT4421
Ricoh FT4421 Ricoh FT4421
115/60 115/60 115/60
110/60 Taiwan 220,240/50 220,240/50 220,240/50
220,240/60 220,240/50
USA, Canada
Canada, L. America
USA, Canada
Europe. etc.
Europe
Europe, etc.
Philippines, etc. A054-28 Service part only
Asia
CODE
A054-15 Service part only
A054-16 A054-17 Service part only A054-19
A054-25
A054-26 A054-27
A054-29
SERIAL NUMBER
Service part only Service part only Service part only Service part only
Service part only
CODE
A054-46
A054-47 Service part only
SERIAL NUMBER
Service part only
Page 78
Reissued on: April 30, ’92
MODIFICATION BULLETIN NO. 32 Page 1 of 2 ISSUED ON: March 31, ’92
Model N230 (220/240V machine only) Volt/Hz
Modified Article Power Supply Cord - 220/240V
Reason for
To minimize the radio frequency noise emission level
Modification
To minimize the radio frequency noise emission level, the ferrite core has been installed to the gro unding wire for the power supply cord.
Old P/N New P/N Description
A0485671 A0485672 Power Supply Cord - 220/240V
---- 16070433 Ferrite Core RI - 14 - 28
Q’ty Used
Old New
1 1 0 1
Interchangeability
X/O 18 63
----- 113 63
Date of
Modification
Parts Catalog
Index No. Page
Serial Number
18
T. Ito, Manager Copier Technical Support
Page 79
Reissued on: April 30, ’92
MODIFICATION BULLETIN NO. 32 Page 2 of 2 ISSUED ON: March 31, ’92
JAPAN PRODUCTION RIF PRODUCTION
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 Ricoh FT4421 110/60 Taiwan A054-19
Nashua 3120 220,240/50 Europe. etc. A054-25 2452010001
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
infotec 9122Z 220,240/50 Europe A054-26 3A4042XXXX A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 276204XXXX A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 2762010764 Ricoh FT4421 220,240/50 Asia A054-29 2761120617
Page 80
Reissued on: April 30, ’92
MODIFICATION BULLETIN NO. 33 Page 1 of 2 ISSUED ON: April 15, ’92
Model N230 Volt/Hz
Modified Article Mylar Seal 19 x 45
Reason for
To prevent the upper cover from being scratched
Modification
Modification
By opening /closing the platen cover, part A of the upper cover may be scratched by the edge of t he platen cover. To prevent this, a mylar seal has been added on part A of the upper cover.
Old P/N New P/N Description Q’ty Interchangeability Index No. Page
---- A0541255 Mylar Seal 19 x 45
0 1
---- 49 9
49
A
Date of
Serial Number
T. Ito, Manager Copier Technical Support
Page 81
Reissued on: April 30, ’92
MODIFICATION BULLETIN NO. 33 Page 2 of 2 ISSUED ON: April 15, ’92
JAPAN PRODUCTION RIF PRODUCTION
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8020201986
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2762010483 Ricoh FT4421 110/60 Taiwan A054-19 276205XXXX
Nashua 3120 220,240/50 Europe. etc. A054-25 2452040001
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
infotec 9122Z 220,240/50 Europe A054-26 3A4052XXXX A054-46 3A46320201 Ricoh FT4421 220,240/50 Europe, etc. A054-27 276205XXXX A054-47 2762630033 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 276205XXXX Ricoh FT4421 220,240/50 Asia A054-29 2762010774
Page 82
MODIFICATION BULLETIN NO. 34
Page 1 of 2
ISSUED ON: April 15,’92
Model
Modified Article
—..
Reason for
Modification
To standardize the parts with other models, the cushion has been modified.
[
Old
PIN
A0483865
N230
Cushion -3 x 18x
Parts standardization
New P/N
~
- -.
-.— ~
A0483864
150mm
Description Cushion -3 x 18 x 150mm Seal - 14 x 18 x 60mm
15
Q’ty
0-1
1-2
Interchangeability
0/0
Volt/Hz
Index No.
3
15 13
Modification
Date of
Page
13
Serial Number
Old
New
Copier Technical Support
Page 83
MODIFICATION BULLETIN NO. 34
Page 2 of 2
ISSUED ON: April 15.’92
MODEL NAME
Savin
.
Nashua 3120
Ricoh FT4421 Ricoh
FT4421 Nashua 3120 infotec 9122Z
Ricoh FT4421 Ricoh
FT4421
Ricoh
FT4421
9210
V/Hz
115/60 115/60 115/60 110/60
I
220,240/50
I
220,240/50
I
220,240/50
I
220,240/60
I
220,240/50
I
DESTINATION
USA, Canada
Canada, L. America
USA, Canada
I
I
I
I
I
I
Taiwan
Europe. etc.
Europe
Europe, etc.
Philippines, etc.IA054-28
Asia
I
I
I I
I
JAPAN PRODUCTIO N
CODE SERIAL NUMBER CODE SERIAL NUMBER
A054-15
A054-16 A054-17 2762030001 A054-19
A054-25 A054-26 A054-27
A054-29
I
I
I
I I
I
8020302011
276205XXXX
2452030005
3A4052XXXX
276205XXXX
276205XXXX
2762030571
I
I
A054-46
I
A054-47
I I
I
RIF PRODUCTION
I
I
3966920001
I
2762670198
I
I I
Page 84
MODIFICATION BULLETIN NO. 36 Page 1 of 2 ISSUED ON: April 30, ’92
Model N230 Volt/Hz
Modified Article Parts Catalog
Reason for
Parts catalog correction
Modification
Please correct your parts catalog as follows:
Incorrect P/N Correct P/N Description Q’ty Used Index No. Page
AB013106 Gear - Drive - Third - Z18 1 41 59
AB030265 Pulley - 24Z 1 41 59
Date of
Modification
Serial Number
T. Ito, Manager Copier Technical Support
Page 85
MODIFICATION BULLETIN NO. 36 Page 2 of 2 ISSUED ON: April 30, ’92
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 Ricoh FT4421 110/60 Taiwan A054-19
Nashua 3120 220,240/50 Europe. etc. A054-25
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
infotec 9122Z 220,240/50 Europe A054-26 A054-46 Ricoh FT4421 220,240/50 Europe, etc. A054-27 A054-47 Ricoh FT4421 220,240/60 Philippines, etc. A054-28 Ricoh FT4421 220,240/50 Asia A054-29
Page 86
MODIFICATION BULLETIN NO. 37 Page 1 of 2 ISSUED ON: June 15, ’92
Model N230 Volt/Hz
Modified Article Bushing - Registration Roller
Reason for
Parts standardization
Modification
To standardize the parts with the N210, the registration roller bushings have been changed.
Old P/N New P/N Description
AA080082 AA080094 Bushing - Front Registration Roller 1 - 1 X/X 10 25 AA080083 AA080095 Bushing - Rear Registration Roller 1 - 1 X/X 29 25 AA143287 54472768 Stepped Screw - M3 2 - 2 X/X 11 25
Q’ty Used
Old New
Interchangeability
The old and new parts are interchangeable as a set (bushing and stepped screw).
Date of
Modification
Parts Catalog
Index No. Page
Serial Number
T. Ito, Manager Copier Technical Support
Page 87
MODIFICATION BULLETIN NO. 37 Page 2 of 2 ISSUED ON: June 15, ’92
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8020502496
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2762050001 Ricoh FT4421 110/60 Taiwan A054-19 276207XXXX
Gestetner 2520ZD 220, 240/50 Europe, etc. A054-22 2452050001
Nashua 3120 220, 240/50 Europe, etc. A054-25 2452050043 infotec 9122Z 220, 240/50 Europe A054-26 3A4072XXXX A054-46 Ricoh FT4421 220, 240/50 Europe, etc. A054-27 2762050315 A054-47 Ricoh FT4421 220, 240/60 Philippines, etc. A054-28 276207XXXX Ricoh FT4421 220, 240/50 Asia A054-29 2762050345
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 88
Reissued on : August 31, ’92
Reissued on :September 30, ’92
MODIFICATION BULLETIN NO. 38 Page 1 of 2 ISSUED ON: June 15, ’92
Model N230 Volt/Hz
Modified Article Scanner Shoe & Scanner Slide Rails
Reason for
To improve the scanner shoe durability
Modification
Date of
Modification
To improve the scanner shoe durability, the mate rial of the scanner shoe and both front an d rea r scann er slide rails h as been changed.
Old P/N New P/N Description
A0481817 Rear Scanner Slide Rail A0481818 Front Scanner Slide Rail
A0751817 Scanner Slide Rail
A0061705 A0691854 Scanner Shoe
Q’ty Used
Old New
1 0 1 0 0 2 7 7
Interchangeability
X/X *1 1 11 X/X 17 11
X/O (as a set) 1 11
X/O *2 12 19
Parts Catalog
Index No. Page
Serial Number
NOTE: (1) As the material of the scanner slide ra ils has be en chan ge d, the fron t an d rea r rails sh ould be replaced at the
same time. (2) The new scanner shoe can be used with the old scan ne r slide rails. However, the scanner shoe must be replaced when the new scanner slide rails are insta lled .
T. Ito, Manager Copier Technical Support
Page 89
Reissued on : August 31, ’92
Reissued on :September 30, ’92
MODIFICATION BULLETIN NO. 38 Page 2 of 2 ISSUED ON: June 15, ’92
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8020302011
Nashua 3120 115/60 Canada, L. America A054-16
Ricoh FT4421 115/60 USA, Canada A054-17 2762020056 Ricoh FT4421 110/60 Taiwan A054-19 276207XXXX
Gestetner 2520ZD 220, 240/50 Europe, etc. A054-22 2452050001
Nashua 3120 220, 240/50 Europe. etc. A054-25 2452020001 A054-45 From 1st Production infotec 9122Z 220, 240/50 Europe A054-26 3A4072XXXX A054-46 3A46620001
Ricoh FT4421 220, 240/50 Europe, etc. A054-27 2762050315 A054-47 2762660001 Ricoh FT4421 220, 240/60 Philippines, etc. A054-28 276207XXXX Ricoh FT4421 220, 240/50 Asia A054-29 2762020381
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 90
MODIFICATION BULLETIN NO. 39 Page 1 of 2 ISSUED ON: June 15, ’92
Model N230 Volt/Hz
Modified Article Rear Base Shielding Plate
Reason for
Parts standardization
Modification
To standardize the parts with the N210, the rear base shielding plate has been changed.
Old P/N New P/N Description
A0481808 A0751808
Rear Base Shielding Plate
Q’ty Used
Old New
1 - 1 X/O 15 21
Interchangeability
Date of
Modification
Parts Catalog
Index No. Page
Serial Number
T. Ito, Manager Copier Technical Support
Page 91
MODIFICATION BULLETIN NO. 39 Page 2 of 2 ISSUED ON: June 15, ’92
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8020402236
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2762040001 Ricoh FT4421 110/60 Taiwan A054-19 276207XXXX
Gestetner 2520ZD 220, 240/50 Europe, etc. A054-22 2452060001
Nashua 3120 220, 240/50 Europe, etc. A054-25 2452040001 infotec 9122Z 220, 240/50 Europe A054-26 3A4072XXXX A054-46 Ricoh FT4421 220, 240/50 Europe, etc. A054-27 2762060856 A054-47 Ricoh FT4421 220, 240/60 Philippines, etc. A054-28 276207XXXX Ricoh FT4421 220, 240/50 Asia A054-29 2762040476
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 92
MODIFICATION BULLETIN NO. 40 Page 1 of 2 ISSUED ON: June 15, ’92
Model N230 Volt/Hz
Modified Article Bushing - Registration Roller
Reason for
To continue supplying parts
Modification
Date of
Modification
Serial Number
The bushings for the registration roller were modified as shown below. (Refer to MB No. 18 and No. 74 for the details.)
(Bushing - Front Registration Roller)
AA080064 AA080082 AA080082 AA080094
X/X X/O as a set X/X X/O as a set
52062684 AA143287 AA143287 54472768
(Bushing - Rear Registration Roller)
AA080065 AA080083 AA080083 AA080095
X/X X/O as a set X/X X/O as a set
52062684 AA143287 AA143287 54472768
But, the oldest parts (AA080064 & AA080065) are no longer available. To continue supplying parts to the field, the following parts have been registered as service parts.
Old P/N New P/N Description
AA080064 Bushing - Front Registration Roller 10 25
A0489508 Bushing Kit - Front Registration Roller 1 - 1 X/O * 25
AA080065 Bushing - Rear Registration Roller 29 25
A0489509 Bushing Kit - Rear Registration Roller 1 - 1 X/O * 25
Q’ty Used
Old New
Interchangeability
Parts Catalog
Index No. Page
Each bushing kit consists of the bushing and stepped screw (AA080094 & 54472768, AA080095 &
54472768).
T. Ito, Manager Copier Technical Support
Page 93
MODIFICATION BULLETIN NO. 40 Page 2 of 2 ISSUED ON: June 15, ’92
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 Service Parts Only
Nashua 3120 115/60 Canada, L. America A054-16 Service Parts Only Ricoh FT4421 115/60 USA, Canada A054-17 Service Parts Only Ricoh FT4421 110/60 Taiwan A054-19 Service Parts Only
Gestetner 2520ZD 220, 240/50 Europe, etc. A054-22 Service Parts Only
Nashua 3120 220, 240/50 Europe, etc. A054-25 Service Parts Only infotec 9122Z 220, 240/50 Europe A054-26 Service Parts Only A054-46 Service Parts Only Ricoh FT4421 220, 240/50 Europe, etc. A054-27 Service Parts Only A054-47 Service Parts Only Ricoh FT4421 220, 240/60 Philippines, etc. A054-28 Service Parts Only Ricoh FT4421 220, 240/50 Asia A054-29 Service Parts Only
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 94
MODIFICATION BULLETIN NO. 41 Page 1 of 2 ISSUED ON: June 15, ’92
Model N230 Volt/Hz
Modified Article Right Contact Stay
Reason for
Parts standardization
Modification
To standardize the parts with the N210, the right contact stay has been changed.
Old P/N New P/N Description
A0481841 A0751841 Right Contact Stay 1 - 1 O/O 11 11
Q’ty Used
Old New
Interchangeability
Date of
Modification
Parts Catalog
Index No. Page
Serial Number
T. Ito, Manager Copier Technical Support
Page 95
MODIFICATION BULLETIN NO. 41 Page 2 of 2 ISSUED ON: June 15, ’92
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8020302011
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2762030001 Ricoh FT4421 110/60 Taiwan A054-19 276207XXXX
Gestetner 2520ZD 220, 240/50 Europe, etc. A054-22 2452050001
Nashua 3120 220, 240/50 Europe, etc. A054-25 2452020001 infotec 9122Z 220, 240/50 Europe A054-26 3A4072XXXX A054-46 Ricoh FT4421 220, 240/50 Europe, etc. A054-27 2762050315 A054-47 Ricoh FT4421 220, 240/60 Philippines, etc. A054-28 276207XXXX Ricoh FT4421 220, 240/50 Asia A054-29 2762030571
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 96
MODIFICATION BULLETIN NO. 42 Page 1 of 2 ISSUED ON: June 15, ’92
Model N230 Volt/Hz
Modified Article Eraser
Reason for
To ensure the image density of the ID sensor pattern
Modification
To ensure the image density of the ID sensor pattern, the acceptable variation for the LEDs light in tensity has been reduced.
Old P/N New P/N Description
A0485230 A0485235 Eraser 1 - 1 X/O 34 55
Q’ty Used
Old New
Interchangeability
Date of
Modification
Parts Catalog
Index No. Page
Serial Number
T. Ito, Manager Copier Technical Support
Page 97
MODIFICATION BULLETIN NO. 42 Page 2 of 2 ISSUED ON: June 15, ’92
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8020402236
Nashua 3120 115/60 Canada, L. America A054-16 Ricoh FT4421 115/60 USA, Canada A054-17 2762040001 Ricoh FT4421 110/60 Taiwan A054-19 276207XXXX
Gestetner 2520ZD 220, 240/50 Europe, etc. A054-22 2452050001
Nashua 3120 220, 240/50 Europe, etc. A054-25 2452040001 infotec 9122Z 220, 240/50 Europe A054-26 3A4072XXXX A054-46 Ricoh FT4421 220, 240/50 Europe, etc. A054-27 2762050315 A054-47 Ricoh FT4421 220, 240/60 Philippines, etc. A054-28 276207XXXX Ricoh FT4421 220, 240/50 Asia A054-29 2762040476
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 98
MODIFICATION BULLETIN NO. 43 Page 1 of 2 ISSUED ON: July 15, ’92
Model N230 Volt/Hz
Modified Article Drum Support Plate Ass’y
Reason for
Parts standardization
Modification
To standardize the parts with the N210, the drum support plate ass’y has been changed.
Old P/N New P/N Description
A0482254 A0752254 Drum Support Plate Ass’y 1 - 1 O/O 43 35
Q’ty Used
Old New
Interchangeability
Date of
Modification
Parts Catalog
Index No. Page
Serial Number
T. Ito, Manager Copier Technical Support
Page 99
MODIFICATION BULLETIN NO. 43 Page 2 of 2 ISSUED ON: July 15, ’92
MODEL NAME
Savin 9210 115/60 USA, Canada A054-15 8020502496
Nashua 3120 115/60 Canada, L. America A054-16
Ricoh FT4421 115/60 USA, Canada A054-17 2762050001 Ricoh FT4421 110/60 Taiwan A054-19 2762070441
Gestetner 2520ZD 220, 240/50 Europe, etc. A054-22 2452060001
Nashua 3120 220, 240/50 Europe. etc. A054-25 2452050043 infotec 9122Z 220, 240/50 Europe A054-26 3A40720001 A054-46
Ricoh FT4421 220, 240/50 Europe, etc. A054-27 2762060856 A054-47 Ricoh FT4421 220, 240/60 Philippines, etc. A054-28 276208XXXX Ricoh FT4421 220, 240/50 Asia A054-29 2762050345
V/Hz DESTINATION
CODE SERIAL NUMBER CODE SERIAL NUMBER
JAPAN PRODUCTION RIF PRODUCTION
Page 100
MODIFICATION BULLETIN NO. 44 Page 1 of 2 ISSUED ON: July 15, ’92
Model N230 Volt/Hz
Modified Article Upper Left Drum Stay
Reason for
Parts standardization
Modification
To standardize the parts with the N210, the upper left drum stay has been changed.
Old P/N New P/N Description
A0482268 A0752268 Upper Left Drum Stay 1 - 1 O/O 11 35
Q’ty Used
Old New
Interchangeability
Date of
Modification
Parts Catalog
Index No. Page
Serial Number
T. Ito, Manager Copier Technical Support
Loading...